Skip to the content
123456789

LMR33640ADDA

Texas InstrumentsExtended

-40℃~+125℃@(TJ) 1 1V~24V 24uA 3.8V~36V 400kHz 4A Adjustable Buck Buck Built-in Yes ESOP-8 DC-DC Converters ROHS

Part id
ti/LMR33640ADDA
Category
DC DC Converters
Package
ESOP-8
Pins
9
In stock
2,635 at JLCPCB (C2836966)
Used on
2 open-source boards

Overview

The LMR33640ADDA is a DC DC Converter made by Texas Instruments in a ESOP-8 package with 9 pins. -40℃~+125℃@(TJ) 1 1V~24V 24uA 3.8V~36V 400kHz 4A Adjustable Buck Buck Built-in Yes ESOP-8 DC-DC Converters ROHS.

PCBKit's library has its KiCad symbol (Regulator_Switching:LMR33640ADDA, from KiCad's library) and its footprint (Package_SO:Texas_HSOP-8-1EP_3.9x4.9mm_P1.27mm, from KiCad's library), ready for a KiCad board. 2,635 are in stock at JLCPCB (part C2836966). 2 open-source boards in 2 repositories on GitHub use it.

Symbol

1GND2VIN3EN4PG5FB6VCC7BOOT8SW
Regulator_Switching:LMR33640ADDAFrom KiCad's library

Footprint

123456789
Package_SO:Texas_HSOP-8-1EP_3.9x4.9mm_P1.27mmFrom KiCad's library

From the datasheet

14
Supply, least
3.8 V · VIN, recommended operating min · p. 5
Supply, most
36 V · VIN, recommended operating max · p. 5
Supply, absolute maximum
38 V · VIN to PGND, absolute max · p. 5
Junction, hottest
150 °C · Junction temperature, absolute max · p. 5
Takes working
25 µA · VIN, typical input supply current in regulation; 3.3-V output, no load · p. 8
Takes asleep
5 µA · VIN, typical shutdown current; EN = 0 · p. 6
Gives
4 A · Rated continuous output current max · p. 5
Current limit
5.5 A · High-side current limit, typical · p. 6
Current limit
4.5 A · Low-side current limit, typical · p. 6
Feedback reference
1 V · FB, adjustable feedback reference, typical · p. 6
Dropout
150 mV · Typical at 1 A, 5-V output; −1% regulation, 140 kHz · p. 8
Junction to air (DDA (HSOIC))
42.9 K/W · Junction-to-ambient thermal resistance, typical · p. 6
Junction to board (DDA (HSOIC))
13.6 K/W · Junction-to-board thermal resistance, typical · p. 6
Junction to case (DDA (HSOIC))
54 K/W · Junction-to-case top thermal resistance, typical · p. 6

What it is and has

6
Converter
3.8-V to 36-V, 4-A synchronous step-down · p. 1
Functional safety
Functional Safety-Capable · p. 1
Control
Peak-current mode control · p. 1
Operating junction temperature
–40°C to +125°C · p. 1
System interface
Power-good flag and precision enable · p. 1
Package
HSOIC (8), 5.00 mm × 4.00 mm · p. 1

Around it

3
cap 1-µF
between VCC and PGND; High-quality capacitor; VCC supplies internal control circuits. · p. 4
cap 100-nF
between BOOT and SW; High-quality bootstrap capacitor for the internal high-side driver. · p. 4
res 100-kΩ
between PG and VCC or VOUT; Power-good pull-up; leave PG floating if unused. · p. 11

Specifications

68
ParameterConditionsAs printedPage
VoltagesVIN to PGNDmin -0.3 · max 38 V5
VoltagesEN to AGND; maximum VIN + 0.3 Vmin -0.3 V5
VoltagesFB to AGNDmin -0.3 · max 5.5 V5
VoltagesPG to AGNDmin 0 · max 22 V5
VoltagesAGND to PGNDmin -0.3 · max 0.3 V5
VoltagesSW to PGND; maximum VIN + 0.3 Vmin -0.3 V5
VoltagesSW to PGND less than 100-ns transientsmin -3.5 · max 38 V5
VoltagesBOOT to SWmin -0.3 · max 5.5 V5
VoltagesVCC to AGNDmin -0.3 · max 5.5 V5
Junction temperature TJmin -40 · max 150 °C5
Storage temperature Tstgmin -55 · max 150 °C5
Electrostatic discharge V(ESD)Human-body model (HBM); ±2500 V ratingmax 2500 V5
Electrostatic discharge V(ESD)Charged-device model (CDM); ±750 V ratingmax 750 V5
Input voltageVIN to PGNDmin 3.8 · max 36 V5
Input voltageEN; maximum VINmin 0 V5
Input voltagePGmin 0 · max 18 V5
Adjustable output voltage VOUTmin 1 · max 24 V5
Output current IOUTmin 0 · max 4 A5
Junction-to-ambient thermal resistance RθJADDA (HSOIC), 8 PINStyp 42.9 °C/W6
Junction-to-case (top) thermal resistance RθJC(top)DDA (HSOIC), 8 PINStyp 54 °C/W6
Junction-to-board thermal resistance RθJBDDA (HSOIC), 8 PINStyp 13.6 °C/W6
Junction-to-top characterization parameter ψJTDDA (HSOIC), 8 PINStyp 4.3 °C/W6
Junction-to-board characterization parameter ψJBDDA (HSOIC), 8 PINStyp 13.8 °C/W6
Junction-to-case (bottom) thermal resistance RθJC(bot)DDA (HSOIC), 8 PINStyp 4.3 °C/W6
Minimum operating input voltage VINVIN = 12 V, VEN = 4 V unless otherwise statedmax 3.8 V6
Non-switching input current; measured at VIN pin IQVFB = 1.2 Vtyp 24 · max 34 uA6
Shutdown quiescent current; measured at VIN pin ISDEN = 0typ 5 · max 10 uA6
EN input level required to turn on internal LDO VEN-VCC-HRising thresholdmax 1 V6
EN input level required to turn off internal LDO VEN-VCC-LFalling thresholdmin 0.3 V6
EN input level required to start switching VEN-HRising thresholdmin 1.2 · typ 1.231 · max 1.26 V6
Hysteresis below VEN-H VEN-HYSHysteresis below VEN-H; fallingtyp 100 mV6
Enable input leakage current ILKG-ENVEN = 3.3 Vtyp 0.2 nA6
Internal LDO output voltage appearing at the VCC pin VCC6 V ≤ VIN ≤ 36 Vmin 4.75 · typ 5 · max 5.25 V6
Bootstrap voltage undervoltage lock-out threshold VBOOT-UVLOtyp 2.2 V6
Feedback voltage; ADJ option VFBADJ optionmin 0.985 · typ 1 · max 1.015 V6
Current into FB pin; ADJ option IFBFB = 1 Vtyp 0.2 · max 50 nA6
High-side current limit ISCLMR33640min 4.8 · typ 5.5 · max 6.2 A6
Low-side current limit ILIMITLMR33640min 3.9 · typ 4.5 · max 5 A6
Minimum peak inductor current IPEAK-MINLMR33640typ 0.824 A6
Zero current detector threshold IZCtyp -0.106 A7
Internal soft-start time tSSmin 2.9 · typ 4 · max 6 ms7
Power-good upper threshold - rising VPG-HIGH-UP% of FB voltagemin 105 · typ 107 · max 110 %7
Power-good upper threshold - falling VPG-HIGH-DN% of FB voltagemin 103 · typ 105 · max 108 %7
Power-good lower threshold - rising VPG-LOW-UP% of FB voltagemin 92 · typ 94 · max 97 %7
Power-good lower threshold - falling VPG-LOW-DN% of FB voltagemin 90 · typ 92 · max 95 %7
Power-good glitch filter delay tPGmin 60 · max 170 us7
Power-good flag RDSON RPGVIN = 12 V, VEN = 4 Vtyp 76 · max 150 Ω7
Power-good flag RDSON RPGVEN = 0 Vtyp 35 · max 60 Ω7
Minimum input voltage for proper PG function VIN-PG50-uA, EN = 0 Vmax 2 V7
PG logic low output VPG50-uA, EN = 0 V, VIN = 2Vmax 0.2 V7
High-side MOSFET ON-resistance RDS-ON-HSDDA packagetyp 95 · max 160 mΩ7
Low-side MOSFET ON-resistance RDS-ON-LSDDA packagetyp 66 · max 110 mΩ7
Minimum switch on-time tON-MINDDA package; VIN = 12 V, VEN = 4 V; typ field is NOMtyp 75 · max 108 ns7
Minimum switch off-time tOFF-MINDDA package; VIN = 12 V, VEN = 4 V; typ field is NOMtyp 50 · max 85 ns7
Maximum switch on-time tON-MAXVIN = 12 V, VEN = 4 V; typ field is NOMtyp 7 · max 9 us7
Operating input voltage range VINVOUT = 3.3 V, IOUT= 0 Amin 3.8 · max 36 V8
Output voltage regulation for VOUT = 5 V VOUTVOUT = 5 V, VIN = 7 V to 36 V, IOUT = 0 A to 4 Amin -1.6 · max 2.5 %8
Output voltage regulation for VOUT = 5 V VOUTVOUT = 5 V, VIN = 7 V to 36 V, IOUT = 1 A to 4 Amin -1.6 · max 1.5 %8
Output voltage regulation for VOUT = 3.3 V VOUTVOUT = 3.3 V, VIN = 3.8 V to 36 V, IOUT = 0 A to 4 Amin -1.6 · max 2.5 %8
Output voltage regulation for VOUT = 3.3 V VOUTVOUT = 3.3 V, VIN = 3.8 V to 36 V, IOUT = 1 A to 4 Amin -1.6 · max 1.5 %8
Input supply current when in regulation ISUPPLYVIN = 12 V, VOUT = 3.3 V, IOUT = 0 A, RFBT = 1 MΩtyp 25 uA8
Dropout voltage; (VIN – VOUT) VDROPVOUT = 5 V, IOUT = 1A; Dropout at –1% of regulation, ƒSW = 140 kHztyp 150 mV8
Maximum switch duty cycle DMAXVIN = VOUT = 12 V, IOUT = 1 Atyp 98 %8
FB pin voltage required to trip short-circuit hiccup mode VHCtyp 0.4 V8
Time between current-limit hiccup burst tHCtyp 94 ms8
Switch voltage dead time tDtyp 2 ns8
Thermal shutdown temperature TSDShutdown temperaturetyp 165 °C8
Thermal shutdown temperature TSDRecovery temperaturetyp 148 °C8

Pins, by the datasheet

9
1 PGND
Power ground; connect to system ground, AGND, and bypass capacitor with short wide traces. · p. 4
2 VIN
Regulator input supply; connect high-quality bypass capacitors directly between this pin and PGND. · p. 4
3 EN
Enable input: high turns on, low turns off; may connect directly to VIN; do not float. · p. 4
4 PG
Power-good flag; connect through a current-limiting resistor to a suitable supply; high indicates power OK; may remain open when unused. · p. 4
5 FB
Feedback input; connect to feedback divider tap; do not float or ground. · p. 4
6 VCC
Internal 5-V LDO output; no external loads except power-good logic supply; connect a 1-uF capacitor to PGND. · p. 4
7 BOOT
Bootstrap supply for internal high-side driver; connect a 100-nF capacitor to SW. · p. 4
8 SW
Regulator switch node; connect to power inductor. · p. 4
THERMAL PAD AGND
Analog ground and thermal connection; solder to the system ground plane for electrical and thermal performance. · p. 4

Open-source boards using it

2
  • 6 layers100 × 100 mmThe Secret Weapon, the printed circuit board in 3D

    The Secret Weapon

    KaiPereira/The-Secret-Weapon

    Your goal is simple: help build the largest collaborative PCB alongside 100 other highschoolers!

    58 parts5
  • 2 layers20 × 37 mm24to5-lmr33640, the printed circuit board in 3D

    24to5-lmr33640

    X-Green/PowerSupply-24Vto5V4A-USB_C_Output

    24 parts

Questions

Is there a KiCad symbol and footprint for the LMR33640ADDA?

Yes. The symbol is Regulator_Switching:LMR33640ADDA and the footprint Package_SO:Texas_HSOP-8-1EP_3.9x4.9mm_P1.27mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the LMR33640ADDA?

ESOP-8, with 9 pins. Its footprint is drawn on this page.

Where is the LMR33640ADDA datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the LMR33640ADDA?

JLCPCB lists it as part C2836966, with 2,635 in stock; the sellers' links on this page open their listings.

Which open-source boards use the LMR33640ADDA?

2 boards in 2 repositories on GitHub; the most starred are listed on this page, with their KiCad files.