Skip to the content
1234567891011121314151617181920

ISOW1044BDFMR

Texas InstrumentsExtended

CAN FD、总线故障检测与保护、低功耗模式、唤醒功能、使能/关断模式 DFM-20 Isolated CAN Transceivers (with Power) ROHS

Part id
ti/ISOW1044BDFMR
Category
AC DC Controllers And Regulators
Package
DFM-20
Pins
20
In stock
0 at JLCPCB (C5216545)
Used on
10 open-source boards

Overview

The ISOW1044BDFMR is an AC DC Controllers And Regulator made by Texas Instruments in a DFM-20 package with 20 pins. CAN FD、总线故障检测与保护、低功耗模式、唤醒功能、使能/关断模式 DFM-20 Isolated CAN Transceivers (with Power) ROHS.

PCBKit's library has its KiCad symbol (Interface_CAN_LIN:ISOW1044, from KiCad's library) and its footprint (Package_SO:SOIC-20W_7.5x12.8mm_P1.27mm, from KiCad's library), ready for a KiCad board. JLCPCB lists it (part C5216545). 10 open-source boards in 4 repositories on GitHub use it.

Symbol

1VIO2IN3TXD4STB5RXD6GNDIO8EN/FLT9VDD10GND111GND212VISOOUT13VSIN14OUT15GISOIN18CANL19CANH20VISOIN
Interface_CAN_LIN:ISOW1044From KiCad's library

Footprint

1234567891011121314151617181920
Package_SO:SOIC-20W_7.5x12.8mm_P1.27mmFrom KiCad's library

From the datasheet

20
Supply, least
1.71 V · VIO, recommended operating min, 1.8V operation · p. 6
Supply, most
1.89 V · VIO, recommended operating max, 1.8V operation · p. 6
Supply, least
2.25 V · VIO, recommended operating min, 2.5V, 3.3V, and 5.5V operation · p. 6
Supply, most
5.5 V · VIO, recommended operating max, 2.5V, 3.3V, and 5.5V operation · p. 6
Supply, least
4.5 V · VDD, recommended operating min · p. 6
Supply, absolute maximum
6 V · VDD, absolute max · p. 6
Works from
-40 °C · ambient operating min, ≤ 50% of bits dominant · p. 7
Works up to
125 °C · ambient operating max, ≤ 50% of bits dominant · p. 7
Junction, hottest
150 °C · junction temperature absolute max · p. 6
A pin gives at most
15 mA · RXD and OUT source or sink absolute max · p. 6
Gives
20 mA · VISOOUT additional output current typical, CAN fully loaded · p. 10
Junction to air (DFM)
68.5 K/W · junction-to-ambient thermal resistance · p. 7
Junction to board (DFM)
44.8 K/W · junction-to-board thermal resistance · p. 7
Junction to case (DFM)
20.9 K/W · junction-to-case top thermal resistance · p. 7
Data rate, most
5 Mbit/s · CAN signaling rate max · p. 7
Data rate, most
10 Mbit/s · extra GPIO channel data rate max · p. 7
Takes working
82.5 mA · sum of IDD and IIO, typical, 5 Mbps 50% duty square wave · p. 13
Takes at most
217 mA · sum of IDD and IIO, max, bus dominant, VIO = 2.25 to 5.5V · p. 13
Takes asleep
18.7 mA · sum of IDD and IIO, typical standby, VIO = 3 to 3.6V · p. 13
Edge
1 ns · RXD output rise time, typical, CL(RXD) = 15pF · p. 14

What it is and has

23
Classical CAN
1Mbps · p. 1
CAN FD
2 and 5Mbps · p. 1
GPIO
Additional 10Mbps channel · p. 1
Converter efficiency
47% typical · p. 1
Isolated output voltage accuracy
± 5% · p. 1
Additional output current
20mA · p. 1
DC bus fault protection
± 58V · p. 1
Receiver common mode input voltage
±12V · p. 1
Wakeup
Remote wakeup using BUS wake-up pattern · p. 1
Loop delay
167ns typical · p. 1
CMTI
100kV/µs typical · p. 1
Protection
Current limit and thermal shutdown · p. 1
Package
20-pin wide SOIC · p. 1
Isolation
Basic · p. 3
UL recognition
UL 1577 component recognition program · p. 1
Physical layer standard
ISO 11898-2:2016 · p. 1
Power converter
Integrated DC-DC converter with low emissions and low noise · p. 1
Power converter frequency
25MHz · p. 1
Protection
±58V DC bus fault protection · p. 23
Standby and wake-up
Standby mode and remote bus wake-up · p. 23
Undervoltage lockout
VDD, VIO and VISOOUT; positive-going and negative-going thresholds with hysteresis · p. 27
ESD
8kV contact ESD per IEC 61000-4-2 standalone · p. 32
Integrated DC-DC converter
low-emissions, low-noise · p. 1

Around it

10
res 5kΩ or greater
between EN/FLT and VIO; Pullup when EN/FLT is used as fault output. · p. 4
ferrite not specified
between GND2 and GISOIN; Optional alternative to a direct PCB connection. · p. 4
ferrite not specified
between VISOOUT and VISOIN; Optional alternative to a direct PCB connection. · p. 4
cap 10 nF
between VDD and GND1; Bypass capacitor within 1 mm of VDD for radiated emissions performance. · p. 32
cap 47µF
between VDD and GND1; Recommended higher bulk decoupling for best noise and ripple performance. · p. 33
cap 10nF
between VDD and GND1; High frequency bypass, 0402 size, within 1mm of the supply pin. · p. 36
cap at least 10μF
between VDD and GND1; Bulk capacitor, after the 10nF capacitor, 2–4mm from the supply pin. · p. 36
cap 100nF or higher
between VIO and GND1; Ceramic bypass capacitor close to the device pins. · p. 36
ferrite BLM15EX331SN1
between VISOOUT and VISOIN; 0402 size; suppress high frequency noise from the power converter output. · p. 36
res 120Ω
between CANH and CANL; Terminate both ends of a cable with 120Ω characteristic impedance. · p. 33

Specifications

150
ParameterConditionsAs printedPage
Power converter supply voltage VDDover operating free-air temperature rangemin -0.5 · max 6 V6
Isolated supply voltage, input supply for CAN transceiver VISOINover operating free-air temperature rangemin -0.5 · max 6 V6
Isolated supply voltage, Power converter output VISOOUTover operating free-air temperature rangemin -0.5 · max 6 V6
Logic supply voltage VIOover operating free-air temperature rangemin -0.5 · max 6 V6
Voltage on bus pins (CANH, CANL with respect to GND2) VBUSover operating free-air temperature rangemin -58 · max 58 V6
Max Differential voltage on bus pins (CANH-CANL) VBUS_DIFFover operating free-air temperature rangemin -45 · max 45 V6
Logic I/O voltage level ( RXD, TXD, STB, EN, IN) Vlogic_IOMaximum VIO + 0.5 V; must not be greater than 6 Vmin -0.5 V6
Logic I/O voltage level Vlogic_IOOUT; maximum VISOIN + 0.5 Vmin -0.5 V6
Output current on RXD, OUT pins IOmin -15 · max 15 mA6
Junction temperature TJmin -40 · max 150 °C6
Storage temperature Tstgmin -65 · max 150 °C6
Electrostatic discharge V(ESD)Human body model (HBM), per ANSI/ESDA/JEDEC JS-001; all pins except bus pins; ±2000 Vmax 2000 V6
Electrostatic discharge V(ESD)Human body model (HBM), per ANSI/ESDA/JEDEC JS-001; CANH, CANL Bus pins w.r.t GND2(pin15/16/17); ±12000 Vmax 12000 V6
Electrostatic discharge V(ESD)Charged device model (CDM), per JEDEC specification JESD22-C101; ±1500 Vmax 1500 V6
Electrostatic discharge V(ESD)per IEC61000-4-2 contact discharge, CANH and CANL with respect to GND2; ±8000 Vmax 8000 V6
Electrostatic discharge V(ESD)per IEC61000-4-2 contact discharge, CANH and CANL with respect to GND1 (across Isolation barrier); ±8000 Vmax 8000 V6
Logic supply voltage VIO1.8V operationmin 1.71 · max 1.89 V6
Logic supply voltage VIO2.5V, 3.3V, and 5.5V operationmin 2.25 · max 5.5 V6
Power converter supply voltage VDDmin 4.5 · max 5.5 V6
Supply threshold when Power converter supply is rising VDD(UVLO+)NOM column recorded in typtyp 2.7 · max 2.95 V6
Supply threshold when Power converter supply is falling VDD(UVLO-)NOM column recorded in typmin 2.4 · typ 2.55 V6
Power converter supply voltage hysteresis VHYS1(UVLO)NOM column recorded in typmin 0.15 · typ 0.24 V6
Rising threshold of Logic supply voltage VIO(UVLO+)max 1.7 V6
Falling threshold of Logic supply voltage VIO(UVLO-)min 1 V6
Logic supply voltage hysteresis VHYS2(UVLO)NOM column recorded in typmin 75 · typ 125 mV7
Low-level input voltage (TXD, STB, EN, and IN inputs) VILMaximum 0.3 × VIOmin 0 V7
High-level output current RXD IOHVIO = 5Vmin -4 mA7
High-level output current RXD IOHVIO = 3.3Vmin -2 mA7
High-level output current RXD IOHVIO = 1.8V or 2.5Vmin -1 mA7
Low-level output current RXD IOLVIO = 5Vmax 4 mA7
Low-level output current RXD IOLVIO = 3.3Vmax 2 mA7
Low-level output current RXD IOLVIO = 1.8V or 2.5Vmax 1 mA7
High-level output current OUT IOHVDD=4.5V to 5.5Vmin -4 mA7
Low-level output current OUT IOLVDD=4.5V to 5.5Vmax 4 mA7
Signaling rate 1/tUICANmax 5 Mbps7
Data rate for extra GPIO channel DRGPIOmax 10 Mbps7
Power up time after applying input supply(Isolated output supply reaches 90% of setpoint and data transmission can start after this) TpwrupNOM column recorded in typtyp 5 ms7
Ambient operating temperature TA≤ 50% of bits are dominantmin -40 · max 125 °C7
Ambient operating temperature TANo condition printed on this linemin -40 · max 105 °C7
Junction-to-ambient thermal resistance RθJADFM, 20 PINStyp 68.5 °C/W7
Junction-to-case (top) thermal resistance RθJC(top)DFM, 20 PINStyp 20.9 °C/W7
Junction-to-board thermal resistance RθJBDFM, 20 PINStyp 44.8 °C/W7
Junction-to-top characterization parameter ΨJTDFM, 20 PINStyp 13 °C/W7
Junction-to-board characterization parameter ΨJBDFM, 20 PINStyp 44 °C/W7
Maximum power dissipation (both sides) PDVIO = VDD = 5.5V, STB= GND1, CAN Bus load RL= 60Ω, TXD=repetitive pattern of 1ms time period with 990us LOW time, 10us HIGH time, Extra load on VISOOUT= 20mAmax 1060 mW7
Maximum power dissipation (side-1) PD1VIO = VDD = 5.5V, STB= GND1, CAN Bus load RL= 60Ω, TXD=repetitive pattern of 1ms time period with 990us LOW time, 10us HIGH time, Extra load on VISOOUT= 20mAmax 490 mW7
Maximum power dissipation by (side-2) PD2VIO = VDD = 5.5V, STB= GND1, CAN Bus load RL= 60Ω, TXD=repetitive pattern of 1ms time period with 990us LOW time, 10us HIGH time, Extra load on VISOOUT= 20mAmax 570 mW7
External clearance(1) CLRShortest terminal-to-terminal distance through air; value >8 mmmin 8 mm8
External creepage(1) CPGShortest terminal-to-terminal distance across the package surface; value >8 mmmin 8 mm8
Distance through the insulation DTIMinimum internal gap (internal clearance – capacitive signal isolation); value >17 ummin 17 um8
Distance through the insulation DTIMinimum internal gap (internal clearance- transformer power isolation); value >120 ummin 120 um8
Comparative tracking index CTIIEC 60112; UL 746A; value >600 Vmin 600 V8
Maximum repetitive peak isolation voltage VIORMDIN EN IEC 60747-17 (VDE 0884-17); AC voltage (bipolar)max 1500 VPK8
Maximum working isolation voltage VIOWMAC voltage (sine wave) Time dependent dielectric breakdown (TDDB) testmax 1000 VRMS8
Maximum working isolation voltage VIOWMDC voltagemax 1500 V8
Maximum transient isolation voltage VIOTMVTEST = VIOTM, t = 60s (qualification); VTEST = 1.2 × VIOTM, t = 1s (100% production)max 7071 VPK8
Maximum surge isolation voltage ISOW1044B(3) VIOSMTest method per IEC 62368-1, 1.2/50 us waveformmax 7800 VPK8
Apparent charge (4) qpdMethod a: After I/O safety test subgroup 2/3, Vini = VIOTM, tini = 60s; Vpd(m) = 1.2 × VIORM , tm = 10s; value ≤5 pCmax 5 pC8
Apparent charge (4) qpdMethod a: After environmental tests subgroup 1, Vini = VIOTM, tini = 60s; ISOW1044B: Vpd(m) = 1.2 × VIORM, tm = 10s; value ≤5 pCmax 5 pC8
Apparent charge (4) qpdAt routine test (100% production), Vini = 1.2 × VIOTM, tini = 1s; ISOW1044B: Vpd(m) = 1.5 × VIORM , tm = 1s (method b1) or Vpd(m) = Vini, tm = tini (method b2); value ≤5 pCmax 5 pC8
Barrier capacitance, input to output(5) CIOVIO = 0.4 sin (2πft), f = 1MHz; value ≅3.5 pFtyp 3.5 pF8
Pollution degreeValue 2typ 28
Withstand isolation voltage VISOUL 1577; VTEST = VISO, t = 60s (qualification); VTEST = 1.2 × VISO , t = 1s (100% production)max 5000 VRMS8
Safety input, output, or supply current(1) ISRθJA = 68.5°C/W, VI = 5.5V, TJ = 150°C, TA = 25°C, See Figure 8-1max 332 mA9
Safety input, output, or supply current(1) ISRθJA = 68.5°C/W, VI = 3.6V, TJ = 150°C, TA = 25°C, See Figure 8-1max 507 mA9
Safety input, output, or total power(1) PSRθJA = 68.5°C/W, TJ = 150 °C, TA = 25°C, See Figure 8-2max 1826 mA9
Safety temperature(1) TSmax 150 ℃9
Isolated Output supply voltage VISOOUTEN=VDD, STB, TXD, IN floatingmin 4.75 · typ 5 · max 5.25 V10
Extra current available on Visoout IoutVDD = 4.5 to 5.5V, CAN full loaded 60Ω, TXD toggling 5Mbps, IN toggling 10Mbpstyp 20 mA10
Output low voltage on OUT pin VOLVDD = 5V ± 10%, IOL = 4mA, IN = GND2max 0.4 V10
Input current, IN IIIN at GND1 or VIOmin -25 · max 25 uA10
Input current, EN IIEN at GND1 or VIOmin -25 · max 25 uA10
Input leakage current IITXD TERMINAL; TXD = VIO or GND1min -25 · max 25 uA10
Input capacitance CITXD TERMINAL; VIN = 0.4 × sin(2 × π × 1E+6 × t) + 1.65V, VIO = 3.3Vtyp 2 pF10
Low level output voltage VOLRXD TERMINAL; IO = 4mA for 4.5V ≤ VIO ≤ 5.5V, See Figure 7-4typ 0.2 · max 0.4 V10
Low level output voltage VOLRXD TERMINAL; IO = 2mA for 3.0V ≤ VIO ≤ 3.6V, See Figure 7-4typ 0.07 · max 0.2 V10
Low level output voltage VOLRXD TERMINAL; IO = 1mA for 2.25V ≤ VIO ≤ 2.75V, See Figure 7-4typ 0.035 · max 0.1 V10
Low level output voltage VOLRXD TERMINAL; IO = 1mA for 1.71V ≤ VIO ≤ 1.89V, See Figure 7-4typ 0.04 · max 0.1 V10
Input leakage current IISTB Terminal; STB = VIO or GND1min -25 · max 25 uA10
Input capacitance CISTB Terminal; VIN = 0.4 × sin(2 × π × 1E+6 × t) + 1.65V, VIO = 3.3Vtyp 2 pF10
Bus output voltage(Dominant), CANH VO(DOM)STB=GND1, TXD = 0V, 50Ω ≤ RL ≤ 65Ω, and CL = open, See Figure 9-1 and Figure 9-2min 2.75 · max 4.5 V10
Bus output voltage(Dominant), CANL VO(DOM)STB=GND1, TXD = 0V, 50Ω ≤ RL ≤ 65Ω, and CL = open, See Figure 9-1 and Figure 9-2min 0.5 · max 2.25 V10
Bus output voltage(recessive), CANH and CANL VO(REC)STB=GND1, TXD = VIO and RL = open, See Figure 9-1 and Figure 9-2; typical 0.5 × VISOINmin 2 · max 3 V10
Differential output voltage(dominant) VOD(DOM)STB=GND1, TXD = 0V, 45Ω ≤ RL ≤ 70Ω, CL = openmin 1.4 · max 3.3 V11
Differential output voltage(dominant) VOD(DOM)STB=GND1, TXD = 0V, 50Ω ≤ RL ≤ 65Ω, CL = openmin 1.5 · max 3 V11
Differential output voltage(dominant) VOD(DOM)STB=GND1, TXD = 0V, RL = 2240Ω, CL = openmin 1.5 · max 5 V11
Differential output voltage(recessive) VOD(REC)TXD = VIO, RL = 60Ω, CL = openmin -120 · max 12 mV11
Differential output voltage(recessive) VOD(REC)TXD = VIO, RL = open, CL = openmin -50 · max 50 mV11
Bus Output Voltage, CANH, Standby mode VO(STB)STB = VIO, RL = openmin -100 · max 100 mV11
Bus Output Voltage, CANL, Standby mode VO(STB)STB = VIO, RL = openmin -100 · max 100 mV11
Bus Output Voltage, CANH-CANL, Standby mode VOD(STB)STB=VIO, RL = openmin -200 · max 200 mV11
Output symmetry (VISOIN - VO(CANH) - VO(CANL)) VSYM_DCRL = 60Ω, CL = open, TXD = VIO or GND1min -400 · max 400 mV11
Short circuit current steady state output current, dominant IOS(SS_DOM)-15 V < CANH < 40 V, CANL = open, TXD = 0 Vmin -115 mA11
Short circuit current steady state output current, dominant IOS(SS_DOM)-15 V < CANL < 40 V, CANH = open, TXD = 0 Vmax 115 mA11
Short circuit current steady state output current, recessive IOS(SS_REC)-27 V < VBUS < 32 V, VBUS = CANH = CANL, TXD = VIOmin -5 · max 5 mA11
Input common mode range VCMSee Figure 9-4 and Table 9-1min -12 · max 12 V11
Differential input threshold voltage, normal mode VIT-12V ≤ VCM ≤ 12V, STB = GND1min 500 · max 900 mV11
Differential input threshold voltage, standby mode VIT(STB)-12V ≤ VCM ≤ 12V, STB = VIOmin 400 · max 1150 mV11
Hysteresis voltage for differential input threshold, normal mode VHYS-12V ≤ VCM ≤ 12V, STB = GND1typ 100 mV11
Dominant state differential input voltage range, normal mode VDIFF(DOM)-12V ≤ VCM ≤ 12V, STB = GND1min 0.9 · max 9 V11
Dominant state differential input voltage range, standby mode VDIFF(DOM)-12V ≤ VCM ≤ 12V, STB = VIOmin 1.15 · max 9 V11
Recessive state differential input voltage range, normal mode VDIFF(REC)-12V ≤ VCM ≤ 12V, STB = GND1min -4 · max 0.5 V11
Recessive state differential input voltage range, standby mode VDIFF(REC)-12V ≤ VCM ≤ 12V, STB = VIOmin -4 · max 0.4 V11
power-off bus input leakage current IOFF(LKG)CANH = CANL = 5V, VDD = VIO = GND1max 5 uA11
Input capacitance to ground (CANH or CANL) CITXD = VIOmax 20 pF11
Differential input capacitance CIDTXD = VIOmax 10 pF11
Differential input resistance RIDTXD = VIO ; -12V ≤ VCM ≤ +12Vmin 40 · max 90 kΩ11
Input resistance (CANH or CANL) RINTXD = VIO ; -12V ≤ VCM ≤ +12Vmin 20 · max 45 kΩ12
Input resistance matching: (1 - RIN(CANH)/RIN(CANL)) × 100% RIN(M)VCANH = VCANL = 5Vmin -1 · max 1 %12
Power converter supply current IDDPower converter disabled; EN = GND1, STB, TXD, IN floatingtyp 0.23 · max 0.27 mA13
Logic supply current IIOPower converter disabled; EN = GND1, STB, TXD, IN floatingtyp 0.34 · max 0.7 mA13
Power converter supply current IDDNormal Mode; TXD = GND1, Bus dominant, RL= 60Ωtyp 124 · max 211 mA13
Power converter supply current IDDNormal Mode; TXD = VIO, Bus recessive, RL = 60Ωtyp 26 · max 46 mA13
Power converter supply current IDDNormal Mode; TXD = 1Mbps 50% duty square wave, RL = 60Ωtyp 76 · max 123 mA13
Power converter supply current IDDNormal Mode; TXD = 5 Mbps 50% duty square wave, RL= 60Ωtyp 78 · max 136 mA13
Logic supply current IIONormal Mode; TXD = GND1, Bus dominant, VIO = 1.71 to 1.89Vtyp 4.3 · max 5.5 mA13
Logic supply current IIONormal Mode; TXD = GND1, Bus dominant, VIO = 2.25 to 5.5Vtyp 4.9 · max 6 mA13
Logic supply current IIONormal Mode; TXD = VIO, Bus recessive, VIO = 1.71 to 1.89Vtyp 3.3 · max 5.4 mA13
Logic supply current IIONormal Mode; TXD = VIO, Bus recessive, VIO = 2.25 to 5.5Vtyp 3.8 · max 5.5 mA13
Logic supply current IIONormal Mode; TXD = 1 Mbps square wave 50% duty, VIO = 3 to 3.6Vtyp 4.4 · max 5.3 mA13
Logic supply current IIONormal Mode; TXD = 5 Mbps square wave 50% duty, VIO = 3 to 3.6Vtyp 4.5 · max 6.2 mA13
Power converter supply current IDDStandby mode; STB = VIO , RL = 60Ωtyp 16 · max 23 mA13
Logic supply current IIOStandby mode; STB = VIO , VIO = 3 to 3.6Vtyp 2.7 · max 3.5 mA13
Total loop delay, driver input TXD to receiver RXD, recessive to dominant tPROP(LOOP1)RL = 60Ω, CL = 100pF, CL(RXD) = 15pF; input rise/fall time (10% to 90%) on TXD = 1ns; 1.71V < VIO < 5.5Vtyp 140 · max 205 ns14
Total loop delay, driver input TXD to receiver RXD, dominant to recessive tPROP(LOOP2)RL = 60Ω, CL = 100pF, CL(RXD) = 15pF; input rise/fall time (10% to 90%) on TXD =1ns; 1.71V < VIO < 5.5Vtyp 167 · max 222 ns14
Mode change time, from Normal to Standby or from Standby to Normal tMODEmax 20 us14
Filter time for a valid wake-up pattern tWK_FILTERmin 0.5 · max 1.8 us14
Bus wake-up timeout value tWK_TIMEOUTmin 0.8 · max 5 ms14
Common mode transient immunity CMTITXD = VIO or GND1, VCM = 1200VPKmin 85 · typ 100 kV/us14
Propagation delay time, LOW to HIGH TXD edge to driver recessive (dominant to recessive) tpHRRL = 60Ω and CL = 100pF; input rise/fall time (10% to 90%) on TXD =1nstyp 87 · max 110 ns14
Propagation delay time, HIGH TO LOW TXD edge to driver dominant (recessive to dominant) tpLDRL = 60Ω and CL = 100pF; input rise/fall time (10% to 90%) on TXD =1nstyp 78 · max 105 ns14
pulse skew (|tpHR - tpLD|) tsk(p)RL = 60Ω and CL = 100pF; input rise/fall time (10% to 90%) on TXD =1nstyp 15 ns14
Differential output signal rise time tRRL = 60Ω and CL = 100pF; input rise/fall time (10% to 90%) on TXD =1nstyp 27 ns14
Differential output signal fall time tFRL = 60Ω and CL = 100pF; input rise/fall time (10% to 90%) on TXD =1nstyp 48 ns14
Driver symmetry (VO(CANH) + VO(CANL))/VCC VSYMRTERM = 60Ω, CL = open, CSPLIT = 4.7nF, TXD = Dominant or recessive or toggling at 250kHz, 1MHzmin 0.9 · max 1.1 V/V14
Dominant time out tTXD_DTORL = 60Ω and CL = openmin 1.2 · max 3.8 ms14
Propagation delay time, bus dominant to recessive transition to RXD high output (dominant to recessive) tpRHCL(RXD) = 15pF, See Figure 7-5typ 90 · max 115 ns14
Propagation delay time, bus recessive to dominant transition to RXD low output (recessive to dominant) tpDLCL(RXD) = 15pF, See Figure 7-5typ 80 · max 105 ns14
Output signal rise time(RXD) tRCL(RXD) = 15pF, See Figure 7-5typ 1 ns14
Output signal fall time(RXD) tFCL(RXD) = 15pF, See Figure 7-5typ 1 ns14
Bit time on CAN bus output pins with tBIT(TXD) = 500ns tBIT(BUS)RL = 60Ω, CL = 100pF, CL(RXD) = 15pF; input rise/fall time (10% to 90%) on TXD =1nsmin 435 · max 530 ns14
Bit time on CAN bus output pins with tBIT(TXD) = 200ns tBIT(BUS)RL = 60Ω, CL = 100pF, CL(RXD) = 15pF; input rise/fall time (10% to 90%) on TXD =1nsmin 155 · max 210 ns14
Bit time on RXD bus output pins with tBIT(TXD) = 500ns tBIT(RXD)RL = 60Ω, CL = 100pF, CL(RXD) = 15pF; input rise/fall time (10% to 90%) on TXD =1nsmin 400 · max 550 ns14
Bit time on RXD bus output pins with tBIT(TXD) = 200ns tBIT(RXD)RL = 60Ω, CL = 100pF, CL(RXD) = 15pF; input rise/fall time (10% to 90%) on TXD =1nsmin 120 · max 220 ns14
Receiver timing symmetry with tBIT(TXD) = 500ns ∆tRECRL = 60Ω, CL = 100pF, CL(RXD) = 15pF; input rise/fall time (10% to 90%) on TXD =1ns; ΔtREC = tBIT(RXD) - tBIT(BUS)min -65 · max 40 ns15
Receiver timing symmetry with tBIT(TXD) = 200ns ∆tRECRL = 60Ω, CL = 100pF, CL(RXD) = 15pF; input rise/fall time (10% to 90%) on TXD =1ns; ΔtREC = tBIT(RXD) - tBIT(BUS)min -45 · max 15 ns15
Propagation delay time tPLH, tPHLGPIO Channeltyp 11 · max 25 ns15
Pulse Width distortion, |tPLH- tPHL| PWDGPIO Channeltyp 3.5 · max 10 ns15
Output signal rise time trGPIO Channeltyp 2.2 · max 5 ns15
Output signal fall time tfGPIO Channeltyp 2.2 · max 5 ns15

Pins, by the datasheet

20
1 VIO
Side 1 Logic supply. · p. 4
2 IN
General purpose logic (GPIO) input with internal pull-down. · p. 4
3 TXD
CAN transmit data input; LOW for dominant and HIGH for recessive bus states. · p. 4
4 STB
Standby enable; connect to GNDIO in normal mode; floating or logic high puts driver in standby mode. · p. 4
5 RXD
CAN receive data output; LOW for dominant and HIGH for recessive bus states. · p. 4
6 GNDIO
Side 1 ground for VIO; short to GND1 on PCB because they are not internally connected. · p. 4
7 NC
Not connected internally. · p. 4
8 EN/FLT
Use as either converter enable input or active-low fault output. Enable high or floating, disable low. Fault output requires a pullup resistor of 5kΩ or greater. · p. 4
9 VDD
Side 1 DC-DC converter power supply. · p. 4
10 GND1
Ground for VDD; short to GNDIO on PCB because they are not internally connected. · p. 4
11 GND2
Ground for VISOOUT; connect to GISOIN directly on PCB or through a ferrite bead. · p. 4
12 VISOOUT
Isolated power converter output voltage; connect to VISOIN directly on PCB or through a ferrite bead. · p. 4
13 VSIN
Power converter input; short pin 12 and pin 13 directly on PCB. · p. 4
14 OUT
General purpose logic (GPIO) output; default output is low. · p. 5
15 GISOIN
Ground for VISOIN; connect to GND2 directly on PCB or through a ferrite bead. · p. 5
16 GISOIN
Ground for VISOIN; connect to GND2 directly on PCB or through a ferrite bead. · p. 5
17 GISOIN
Ground for VISOIN; connect to GND2 directly on PCB or through a ferrite bead. · p. 5
18 CANL
Low-level CAN bus line. · p. 5
19 CANH
High-level CAN bus line. · p. 5
20 VISOIN
Power supply input for CAN transceiver; connect to VISOOUT directly on PCB or through a ferrite bead. · p. 5

Ordering codes, by the datasheet

6
ISOW1044BDFMR
SOIC (DFM) | 20 · 850 | LARGE T&R; operating temperature -40 to 125°C · p. 43
ISOW1044BDFMR.A
SOIC (DFM) | 20 · 850 | LARGE T&R; operating temperature -40 to 125°C · p. 43
ISOW1044DFMR
SOIC (DFM) | 20 · 850 | LARGE T&R; operating temperature -40 to 125°C · p. 43
ISOW1044DFMR.A
SOIC (DFM) | 20 · 850 | LARGE T&R; operating temperature -40 to 125°C · p. 43
ISOW1044DFMRG4
SOIC (DFM) | 20 · 850 | LARGE T&R; operating temperature -40 to 125°C · p. 43
ISOW1044DFMRG4.A
SOIC (DFM) | 20 · 850 | LARGE T&R; operating temperature -40 to 125°C · p. 43

Open-source boards using it

10See all 10
  • 6 layers55 × 35 mmTACCO, the printed circuit board in 3D

    TACCO

    Stab-Rabbit-coding/Serenity-UAV

    A functional, security conscious, Unmanned Aerial Vehicle based on the Firefly Class spacecraft Serenity from the 2002 show..

    163 parts1CERN-OHL-W-2.0
  • 2 layers60 × 54 mmAif io, the printed circuit board in 3D

    Aif io

    hcmos/aif-io_pcb

    91 parts
  • 2 layers64.3 × 19.5 mmCAN PERIPH GW-1, the printed circuit board in 3D

    CAN PERIPH GW-1

    Stab-Rabbit-coding/Serenity-UAV

    A functional, security conscious, Unmanned Aerial Vehicle based on the Firefly Class spacecraft Serenity from the 2002 show..

    49 parts1CERN-OHL-W-2.0
  • 4 layers55 × 35 mmCAPE A-2, the printed circuit board in 3D

    CAPE A-2

    Stab-Rabbit-coding/Serenity-UAV

    A functional, security conscious, Unmanned Aerial Vehicle based on the Firefly Class spacecraft Serenity from the 2002 show..

    40 parts1CERN-OHL-W-2.0
  • 4 layers55 × 35 mmCAPE B-2, the printed circuit board in 3D

    CAPE B-2

    Stab-Rabbit-coding/Serenity-UAV

    A functional, security conscious, Unmanned Aerial Vehicle based on the Firefly Class spacecraft Serenity from the 2002 show..

    42 parts1CERN-OHL-W-2.0
  • 4 layers90 × 65 mmFlightEngineer, the printed circuit board in 3D

    FlightEngineer

    Stab-Rabbit-coding/Serenity-UAV

    A functional, security conscious, Unmanned Aerial Vehicle based on the Firefly Class spacecraft Serenity from the 2002 show..

    153 parts1CERN-OHL-W-2.0
  • 6 layers55 × 35 mmPilot, the printed circuit board in 3D

    Pilot

    Stab-Rabbit-coding/Serenity-UAV

    A functional, security conscious, Unmanned Aerial Vehicle based on the Firefly Class spacecraft Serenity from the 2002 show..

    136 parts1CERN-OHL-W-2.0

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the ISOW1044BDFMR?

Yes. The symbol is Interface_CAN_LIN:ISOW1044 and the footprint Package_SO:SOIC-20W_7.5x12.8mm_P1.27mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the ISOW1044BDFMR?

DFM-20, with 20 pins. Its footprint is drawn on this page.

Where is the ISOW1044BDFMR datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the ISOW1044BDFMR?

JLCPCB lists it as part C5216545, with 0 in stock; the sellers' links on this page open their listings.

What can replace the ISOW1044BDFMR?

Parts like it in the library: the UCC3895DWTR by Texas Instruments, the L4981AD013 by STMicroelectronics, the STNRG012 by STMicroelectronics and the UCC28513DW by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the ISOW1044BDFMR?

10 boards in 4 repositories on GitHub; the most starred are listed on this page, with their KiCad files.