
ISO1050DUBR
Texas InstrumentsExtended
-55℃~+105℃ 1 1Mbps 2500 3V~5.5V 4.75V~5.25V 50kV/us Bus fault detection and protection、Fail-safe SOP-8 Isolated CAN Transceivers ROHS
- Part id
- ti/ISO1050DUBR
- Category
- Isolated CAN Transceivers
- Package
- SOP-8
- Pins
- 8
- In stock
- 1,663 at JLCPCB (C16428)
- Used on
- 8 open-source boards
Overview
The ISO1050DUBR is an isolated CAN Transceiver made by Texas Instruments in a SOP-8 package with 8 pins. -55℃~+105℃ 1 1Mbps 2500 3V~5.5V 4.75V~5.25V 50kV/us Bus fault detection and protection、Fail-safe SOP-8 Isolated CAN Transceivers ROHS.
PCBKit's library has its KiCad symbol (Interface_CAN_LIN:ISO1050DUB, from KiCad's library) and its footprint (Package_SO:SOP-8_3.76x4.96mm_P1.27mm, from KiCad's library), ready for a KiCad board. 1,663 are in stock at JLCPCB (part C16428). 8 open-source boards in 6 repositories on GitHub use it.
Symbol
Footprint
From the datasheet
17- Supply, least
- 3 V · VCC1, recommended operating min · p. 6
- Supply, most
- 5.5 V · VCC1, recommended operating max · p. 6
- Supply, least
- 4.75 V · VCC2, recommended operating min · p. 6
- Supply, most
- 5.25 V · VCC2, recommended operating max · p. 6
- Supply, absolute maximum
- 6 V · VCC1, absolute max · p. 6
- Works from
- -55 °C · Operating ambient temperature min · p. 6
- Works up to
- 105 °C · Operating ambient temperature max · p. 6
- Junction, hottest
- 150 °C · Junction temperature absolute max · p. 6
- A pin gives at most
- 15 mA · RXD source or sink absolute max · p. 6
- Takes working
- 9.8 mA · sum of ICC1 and ICC2 typical, recessive receive, VCC1 = 3.3 V, VCC2 = 5 V · p. 10
- Takes at most
- 76.6 mA · sum of ICC1 and ICC2 max, bus dominant, RL = 60 Ω · p. 10
- Junction to air (DUB)
- 84.3 K/W · Junction-to-ambient thermal resistance · p. 7
- Junction to case (DUB)
- 63.2 K/W · Junction-to-case top thermal resistance · p. 7
- Junction to board (DUB)
- 43 K/W · Junction-to-board thermal resistance · p. 7
- Data rate, most
- 1 Mbit/s · CAN signaling rate max · p. 1
- Edge
- 3 ns · RXD output rise or fall time typical · p. 12
- Takes working
- 53.8 mA · sum of typical ICC1 at VCC1 = 3.3 V and ICC2, bus dominant, RL = 60 Ω · p. 10
What it is and has
11- CAN standard
- ISO11898-2 · p. 1
- Isolation
- 2500 VRMS (ISO1050DUB) · p. 1
- Fail-safe outputs
- Supported · p. 1
- Bus-fault protection
- –27 V to 40 V · p. 1
- TXD protection
- Driver dominant time-out function · p. 1
- Logic compatibility
- 3.3 V and 5 V microprocessors · p. 1
- UL approval
- UL 1577 · p. 1
- Standard
- ISO11898-2 · p. 1
- Isolation
- 2500 VRMS, ISO1050DUB · p. 1
- Fail-safe outputs
- Yes · p. 1
- Transient immunity
- 50 kV/μs typical · p. 1
Around it
2- res unspecified
- between TXD and VCC1; Pull up TXD to force a recessive input level if the microprocessor output floats. · p. 21
- res 120 Ω
- between CANH and CANL; Terminate each end of the bus, on the cable or in a terminating node. · p. 25
Specifications
101| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Supply voltage, side 1 VCC1 | Over operating free-air temperature range | min -0.5 · max 6 V | 6 |
| Supply voltage, side 2 VCC2 | Over operating free-air temperature range | min -0.5 · max 6 V | 6 |
| Logic input voltage range (TXD) VIO | Maximum VCC1+0.5 V; must not exceed 6 V | min -0.5 V | 6 |
| Voltage on bus pins (CANH, CANL) VBUS | min -27 · max 40 V | 6 | |
| Output current on RXD pin IO | min -15 · max 15 mA | 6 | |
| Junction temperature TJ | min -55 · max 150 ℃ | 6 | |
| Storage temperature TSTG | min -65 · max 150 ℃ | 6 | |
| Electrostatic discharge, Human body model (HBM), per ANSI/ESDA/JEDEC JS-001 V(ESD) | All pins | min -4000 · max 4000 V | 6 |
| Electrostatic discharge, Charged device model (CDM), per JEDEC specification JESD22-C101 V(ESD) | All pins | min -1500 · max 1500 V | 6 |
| Electrostatic discharge, Charged machine model, ANSI/ESDS5.2-1996 V(ESD) | All pins | min -200 · max 200 V | 6 |
| Supply Voltage, Side 1 VCC1 | min 3 · max 5.5 V | 6 | |
| Supply Voltage, Side 2 VCC2 | min 4.75 · max 5.25 V | 6 | |
| Voltage at bus pins (separately or common mode) VI or VIC | min -12 · max 12 V | 6 | |
| High-level input voltage (TXD) VIH | min 2 · max 5.25 V | 6 | |
| Low-level input voltage (TXD) VIL | min 0 · max 0.8 V | 6 | |
| Differential input voltage VID | min -7 · max 7 V | 6 | |
| High-Level Output current, Driver IOH | min -70 mA | 6 | |
| High-Level Output current, Receiver IOH | min -4 mA | 6 | |
| Low-level output current, Driver IOL | max 70 mA | 6 | |
| Low-level output current, Receiver IOL | max 4 mA | 6 | |
| Operating ambient temperature TA | min -55 · max 105 °C | 6 | |
| Junction temperature TJ | min -55 · max 125 °C | 6 | |
| Thermal shutdown temperature TJshutdown | typ 190 °C | 6 | |
| Junction-to-ambient thermal resistance RΘJA | DUB, 8 PINS | typ 84.3 °C/W | 7 |
| Junction-to-case (top) thermal resistance RΘJC(top) | DUB, 8 PINS | typ 63.2 °C/W | 7 |
| Junction-to-board thermal resistance RΘJB | DUB, 8 PINS | typ 43 °C/W | 7 |
| Junction-to-top characterization parameter ΨJT | DUB, 8 PINS | typ 27.4 °C/W | 7 |
| Junction-to-board characterization parameter ΨJB | DUB, 8 PINS | typ 42.7 °C/W | 7 |
| Maximum power dissipation (both sides) PD | VCC1 = VCC2 = 5.25 V, TJ = 150°C, RL = 60 Ω; TXD with 5V, 500kHz 50% duty square wave | max 200 mW | 7 |
| Maximum power dissipation (side-1) PD1 | VCC1 = VCC2 = 5.25 V, TJ = 150°C, RL = 60 Ω; TXD with 5V, 500kHz 50% duty square wave | max 25 mW | 7 |
| Maximum power dissipation (side-2) PD2 | VCC1 = VCC2 = 5.25 V, TJ = 150°C, RL = 60 Ω; TXD with 5V, 500kHz 50% duty square wave | max 175 mW | 7 |
| External clearance CLR | DUB-8; side 1 to side 2 distance through air; >6.1 mm | min 6.1 mm | 8 |
| External Creepage CPG | DUB-8; side 1 to side 2 distance across package surface; >6.8 mm | min 6.8 mm | 8 |
| Distance through the insulation DTI | DUB-8; minimum internal gap (internal clearance); >13.5 um | min 13.5 um | 8 |
| Comparative tracking index CTI | DUB-8; IEC 60112; UL 746A; >600 V | min 600 V | 8 |
| Maximum repetitive peak isolation voltage VIORM | DUB-8; AC voltage (bipolar) | max 560 VPK | 8 |
| Maximum isolation working voltage VIOWM | DUB-8; AC voltage (sine wave); time-dependent dielectric breakdown (TDDB) test | max 395 VRMS | 8 |
| Maximum isolation working voltage VIOWM | DUB-8; DC voltage | max 560 VDC | 8 |
| Maximum transient isolation voltage VIOTM | DUB-8; VTEST = VIOTM, t = 60 s qualification; VTEST = 1.2 × VIOTM, t = 1 s production | max 4000 VPK | 8 |
| Maximum surge isolation voltage VIOSM | DUB-8; IEC 62368-1, 1.2/50 us waveform, VTEST = 1.6 x VIOSM = 6.4 kVPK qualification | max 4000 VPK | 8 |
| Apparent charge qpd | DUB-8; Method a after I/O safety test subgroup 2/3; Vini = VIOTM, tini = 60 s; Vpd(m) = 1.2 × VIORM, tm = 10 s | max 5 pC | 8 |
| Apparent charge qpd | DUB-8; Method a after environmental tests subgroup 1; Vini = VIOTM, tini = 60 s; Vpd(m) = 1.3 × VIORM, tm = 10 s | max 5 pC | 8 |
| Apparent charge qpd | DUB-8; Method b routine production test; Vini = 1.2 x VIOTM, tini = 1 s; Vpd(m) = 1.5 x VIORM, tm = 1 s | max 5 pC | 8 |
| Barrier capacitance, input to output CIO | DUB-8; VIO = 0.4 × sin (2 πft), f = 1 MHz | typ 1 pF | 8 |
| Pollution degree | DUB-8 | max 2 | 8 |
| Withstand isolation voltage VISO | DUB-8; UL 1577; VTEST = VISO, t = 60 s qualification; VTEST = 1.2 × VISO, t = 1 s production | max 2500 VRMS | 8 |
| Safety input, output, or supply current IS | DUB-8; RθJA = 84.3°C/W, VI = 5.5 V, TJ = 150°C, TA = 25°C | max 269 mA | 9 |
| Safety input, output, or supply current IS | DUB-8; RθJA = 84.3°C/W, VI = 3.6 V, TJ = 150°C, TA = 25°C | max 411 mA | 9 |
| Maximum safety temperature TS | DUB-8 | max 150 °C | 9 |
| Supply current Side 1 ICC1 | VI = 0 V or VCC1, VCC1 = 3.3 V | typ 1.8 · max 3.6 mA | 10 |
| Supply current Side 1 ICC1 | VI = 0 V or VCC1, VCC1 = 5.0 V | typ 2.3 · max 3.6 mA | 10 |
| Supply current Side 2 ICC2 | VI = 0 V, bus dominant, RL = 60 Ω | typ 52 · max 73 mA | 10 |
| Supply current Side 2 ICC2 | VI = VCC1 | typ 8 · max 12 mA | 10 |
| Bus output voltage(Dominant), CANH VO(DOM) | See Figure 7-1 and Figure 7-2, VI = 0 V, RL = 60 Ω | min 2.9 · typ 3.5 · max 4.5 V | 10 |
| Bus output voltage(Dominant), CANL VO(DOM) | See Figure 7-1 and Figure 7-2, VI = 0 V, RL = 60 Ω | min 0.8 · typ 1.2 · max 1.78 V | 10 |
| Bus output voltage(recessive), CANH and CANL VO(REC) | See Figure 7-1 and Figure 7-2, VI = 2 V, RL = 60 Ω | min 2 · typ 2.3 · max 3 V | 10 |
| Differential output voltage(dominant) VOD(DOM) | See Figure 7-1 and Figure 7-2, VI = 0 V, RL = 60 Ω | min 1.5 · max 3 V | 10 |
| Differential output voltage(dominant) VOD(DOM) | See Figure 7-1 and Figure 7-2, VI = 0 V, RL = 45 Ω, VCC > 4.8 V | min 1.4 · max 3 V | 10 |
| Differential output voltage(recessive) VOD(REC) | See Figure 7-1 and Figure 7-2, VI = 3 V, RL = 60 Ω | min -120 · max 12 mV | 10 |
| Differential output voltage(recessive) VOD(REC) | VI = 3 V, No Load | min -500 · max 50 mV | 10 |
| Common-mode output voltage (Dominant) VOC(DOM) | See Figure 7-8 | min 2 · typ 2.3 · max 3 V | 10 |
| Peak-to-peak common-mode output voltage VOC(pp) | See Figure 7-8 | typ 0.3 V | 10 |
| High level input leakage current IIH | VI = 2 V | max 5 uA | 10 |
| Low level input leakage current IIL | VI = 0.8 V | min -5 uA | 10 |
| Power-off TXD leakage current IO(off) | VCC1, VCC2 at 0 V, TXD = 5 V | max 10 uA | 10 |
| Short circuit current steady state output current, dominant IOS(ss) | See Figure 7-11, CANH = –12 V, CANL Open | min -105 · typ -72 mA | 10 |
| Short circuit current steady state output current, dominant IOS(ss) | See Figure 7-11, VCANH = 12 V, CANL Open | typ 0.36 · max 6.2 mA | 10 |
| Short circuit current steady state output current, dominant IOS(ss) | See Figure 7-11, VCANL =–12 V, CANH Open | min -1 · typ -0.5 mA | 10 |
| Short circuit current steady state output current, dominant IOS(ss) | See Figure 7-11, VCANL = 12 V, CANH Open | typ 71 · max 105 mA | 10 |
| Common-mode transient immunity CMTI | Driver; See Figure 7-13, VI = VCC or 0 V | min 25 · typ 50 kV/us | 10 |
| Positive-going bus input threshold voltage VIT+ | See Table 1 | typ 750 · max 900 mV | 10 |
| Negative-going bus input threshold voltage VIT- | See Table 1 | min 500 · typ 650 mV | 10 |
| Hysteresis voltage for differential input threshold VHYS | See Table 1 | typ 150 mV | 10 |
| High level output voltage with Vcc = 5 V VOH | IO = -4 mA, See Figure 7-6; minimum Vcc - 0.8 V | typ 4.6 V | 10 |
| High level output voltage with Vcc = 5 V VOH | IO = -20 uA, See Figure 7-6; minimum Vcc - 0.1 V | typ 5 V | 10 |
| High level output voltage with Vcc1 = 3.3 V VOH | IO = 4 mA, See Figure 7-6; minimum Vcc - 0.8 V | typ 3.1 V | 10 |
| High level output voltage with Vcc1 = 3.3 V VOH | IO = 20 uA, See Figure 7-6; minimum Vcc - 0.1 V | typ 3.3 V | 10 |
| Low level output voltage VOL | IO = 4 mA, See Figure 7-6 | typ 0.2 · max 0.4 V | 10 |
| Low level output voltage VOL | IO = 20 uA, See Figure 7-6 | typ 0 · max 0.1 V | 10 |
| Input capacitance to ground (CANH or CANL) CI | TXD = 3 V, VI = 0.4 sin (4e6pi*t) + 2.5 V | typ 12 pF | 11 |
| Differential input capacitance CID | TXD = 3 V, VI = 0.4 sin (4e6pi*t) | typ 8 pF | 11 |
| Differential input resistance RID | TXD = 3 V | min 40 · max 90 kΩ | 11 |
| Input resistance (CANH or CANL) RIN | TXD = 3 V | min 20 · max 45 kΩ | 11 |
| Input resistance matching: (1 - RIN(CANH)/RIN(CANL)) x 100% RIN(M) | VCANH = VCANL | min -3 · max 3 % | 11 |
| Common-mode transient immunity CMTI | Receiver; See Figure 7-13, VI = VCC or 0 V | min 25 · typ 50 kV/us | 11 |
| Total loop delay, driver input TXD to receiver RXD, recessive to dominant tPROP(LOOP1) | See Figure 7-9 | min 100 · typ 150 · max 210 ns | 12 |
| Total loop delay, driver input TXD to receiver RXD, dominant to recessive tPROP(LOOP2) | See Figure 7-9 | min 112 · typ 150 · max 210 ns | 12 |
| Propagation delay time, recessive-to-dominant output tPLH | Driver; See Figure 7-4 | typ 74 · max 110 ns | 12 |
| Propagation delay time, dominant-to-recessive output tPHL | Driver; See Figure 7-4 | typ 82 · max 110 ns | 12 |
| Differential output signal rise time tR | Driver; See Figure 7-4 | typ 20 · max 50 ns | 12 |
| Differential output signal fall time tF | Driver; See Figure 7-4 | typ 52 · max 63 ns | 12 |
| Dominant time out tTXD_DTO | CL = 100 pF, See Figure 7-10 | min 1.2 · max 4 ms | 12 |
| Propagation delay time, low-to-high-level output tPLH | Receiver; TXD at 3 V, See Figure 7-6 | min 66 · typ 90 · max 130 ns | 12 |
| Propagation delay time, high-to-low-level output tPHL | Receiver; TXD at 3 V, See Figure 7-6 | min 51 · typ 80 · max 105 ns | 12 |
| Output signal rise time(RXD) tR | Receiver; TXD at 3 V, See Figure 7-6 | typ 3 · max 6 ns | 12 |
| Output signal fall time(RXD) tF | Receiver; TXD at 3 V, See Figure 7-6 | typ 3 · max 6 ns | 12 |
| Fail-Safe output delay time from bus-side power loss tfs | VCC1 at 5 V, See Figure 7-12 | typ 6 us | 12 |
| High level output voltage with Vcc = 5 V VOH | IO = -4 mA, See Figure 7-6; minimum is Vcc - 0.8 V | typ 4.6 V | 10 |
| High level output voltage with Vcc = 5 V VOH | IO = -20 uA, See Figure 7-6; minimum is Vcc - 0.1 V | typ 5 V | 10 |
| High level output voltage with Vcc1 = 3.3 V VOH | IO = 4 mA, See Figure 7-6; minimum is Vcc - 0.8 V | typ 3.1 V | 10 |
| High level output voltage with Vcc1 = 3.3 V VOH | IO = 20 uA, See Figure 7-6; minimum is Vcc - 0.1 V | typ 3.3 V | 10 |
Pins, by the datasheet
8- 1 VCC1
- Digital-side supply voltage (3 to 5.5 V). · p. 5
- 2 RXD
- CAN receive data output, LOW for dominant and HIGH for recessive bus states. · p. 5
- 3 TXD
- CAN transmit data input, LOW for dominant and HIGH for recessive bus states. · p. 5
- 4 GND1
- Digital-side ground connection. · p. 5
- 5 GND2
- Transceiver-side ground connection. · p. 5
- 6 CANL
- Low-level CAN bus line. · p. 5
- 7 CANH
- High-level CAN bus line. · p. 5
- 8 VCC2
- Transceiver-side supply voltage (5 V). · p. 5
Ordering codes, by the datasheet
9- ISO1050DUBR
- SOP (DUB) | 8 · Active; 350 | LARGE T&R; -55 to 105 °C · p. 33
- ISO1050DUBR.A
- SOP (DUB) | 8 · Active; 350 | LARGE T&R; -55 to 105 °C · p. 33
- ISO1050DUBRG4
- SOP (DUB) | 8 · Active; 350 | LARGE T&R; -55 to 105 °C · p. 33
- ISO1050DUBRG4.A
- SOP (DUB) | 8 · Active; 350 | LARGE T&R; -55 to 105 °C · p. 33
- ISO1050DW
- SOIC (DW) | 16 · Obsolete; -55 to 105 °C · p. 33
- ISO1050DWR
- SOIC (DW) | 16 · Active; 2000 | LARGE T&R; -55 to 105 °C · p. 33
- ISO1050DWR.A
- SOIC (DW) | 16 · Active; 2000 | LARGE T&R; -55 to 105 °C · p. 33
- ISO1050DWRG4
- SOIC (DW) | 16 · Active; 2000 | LARGE T&R; -55 to 105 °C · p. 33
- ISO1050DWRG4.A
- SOIC (DW) | 16 · Active; 2000 | LARGE T&R; -55 to 105 °C · p. 33
Open-source boards using it
8- 2 layers100 × 100 mm

- 2 layers115.7 × 107.6 mm

- 4 layers100 × 107.7 mm

- 2 layers320 × 55 mm

- 2 layers135.1 × 159.4 mm

- 2 layers104.9 × 90 mm

- 2 layers130 × 90 mm

- 2 layers80 × 30 mm

Questions
Is there a KiCad symbol and footprint for the ISO1050DUBR?
Yes. The symbol is Interface_CAN_LIN:ISO1050DUB and the footprint Package_SO:SOP-8_3.76x4.96mm_P1.27mm, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the ISO1050DUBR?
SOP-8, with 8 pins. Its footprint is drawn on this page.
Where is the ISO1050DUBR datasheet?
Texas Instruments publishes it: the Datasheet link on this page opens it.
Where can I order the ISO1050DUBR?
JLCPCB lists it as part C16428, with 1,663 in stock; the sellers' links on this page open their listings.
Which open-source boards use the ISO1050DUBR?
8 boards in 6 repositories on GitHub; the most starred are listed on this page, with their KiCad files.