Skip to the content
12345678910

FDC1004DGSR

Texas InstrumentsExtended

-40℃~+125℃ 1kV 29uA 3V~3.6V 4 750uA Capacitive Touch MSOP-10 Touch Sensors ROHS

Part id
ti/FDC1004DGSR
Category
Touch Sensors
Package
MSOP-10
Pins
10
In stock
7,127 at JLCPCB (C2865994)
Used on
9 open-source boards

Overview

The FDC1004DGSR is a touch Sensor made by Texas Instruments in a MSOP-10 package with 10 pins. -40℃~+125℃ 1kV 29uA 3V~3.6V 4 750uA Capacitive Touch MSOP-10 Touch Sensors ROHS.

PCBKit's library has its KiCad symbol (Sensor_Proximity:FDC1004DGS, from KiCad's library) and its footprint (Package_SO:MSOP-10_3x3mm_P0.5mm, from KiCad's library), ready for a KiCad board. 7,127 are in stock at JLCPCB (part C2865994). 9 open-source boards in 6 repositories on GitHub use it.

Symbol

1SHLD12CIN13CIN24CIN35CIN46SHLD27GND8VDD9SCL10SDA
Sensor_Proximity:FDC1004DGSFrom KiCad's library

Footprint

12345678910
Package_SO:MSOP-10_3x3mm_P0.5mmFrom KiCad's library

From the datasheet

13
Supply, least
3 V · VDD, recommended operating min · p. 4
Supply, most
3.6 V · VDD, recommended operating max · p. 4
Supply, absolute maximum
6 V · VDD, absolute max · p. 4
Works from
-40 °C · Operating temperature min · p. 4
Works up to
125 °C · Operating temperature max · p. 4
Junction, hottest
150 °C · Junction temperature absolute max · p. 4
Takes working
750 µA · VDD, conversion mode typical, digital inputs at VDD or GND · p. 5
Takes at most
950 µA · VDD, conversion mode max, digital inputs at VDD or GND · p. 5
Takes asleep
29 µA · VDD, standby typical, digital inputs at VDD or GND · p. 5
A pin gives at most
3 mA · Input current at any pin, absolute max · p. 4
Junction to air (VSSOP (DGS))
46.8 K/W · Junction-to-ambient thermal resistance · p. 4
Junction to case (VSSOP (DGS))
48.7 K/W · Junction-to-case(top) thermal resistance · p. 4
Junction to board (VSSOP (DGS))
70.6 K/W · Junction-to-board thermal resistance · p. 4

What it is and has

7
Input range
±15pF · p. 1
Measurement resolution
0.5fF · p. 1
Maximum offset capacitance
100pF · p. 1
Programmable output rates
100/200/400 S/s · p. 1
Maximum shield load
400pF · p. 1
Interface
I2C · p. 1
Number of channels
4 · p. 1

Around it

2
cap 1μF
between VDD and GND; Tantalum; example decoupling combination with a 0.1uF multilayer ceramic capacitor. · p. 3
cap 0.1μF
between VDD and GND; Multilayer ceramic; example decoupling combination with a 1uF tantalum capacitor. · p. 3

Specifications

40
ParameterConditionsAs printedPage
Input voltageVDDmin -0.3 · max 6 V4
Input voltageSCL, SDAmin -0.3 · max 6 V4
Input voltageat any other pinmin -0.3 V4
Input currentat any pinmax 3 mA4
Junction temperature(2)max 150 °C4
Storage temperature TSTGmin -65 · max 150 °C4
Supply voltage (VDD-GND)Over operating temperature rangemin 3 · typ 3.3 · max 3.6 V4
Temperaturemin -40 · max 125 °C4
Junction-to-ambient thermal resistance RθJAVSSOP (DGS), 10 PINStyp 46.8 °C/W4
Junction-to-case(top) thermal resistance RθJCVSSOP (DGS), 10 PINStyp 48.7 °C/W4
Junction-to-board thermal resistance RθJBVSSOP (DGS), 10 PINStyp 70.6 °C/W4
Supply current IDDConversion mode; Digital input to VDD or GND; VDD = 3.3V, TA = 25°Ctyp 750 · max 950 uA5
Supply current IDDStandby; Digital input to VDD or GND; VDD = 3.3V, TA = 25°Ctyp 29 · max 70 uA5
Max input offset capacitance COMAXper channel, Series resistance at CINn n=1.4 = 0 Ω; VDD = 3.3V, TA = 25°Ctyp 100 pF5
Effective resolution (4) RESSample rate = 100S/s (5); no external capacitance connected; VDD = 3.3V, TA = 25°Ctyp 16 bit5
Output noise EONSample rate = 100S/s (5); no external capacitance connected; VDD = 3.3V, TA = 25°Ctyp 33.2 aF/√Hz5
Offset deviation over temperature TcCOFF-40°C < T < 125°C; VDD = 3.3Vtyp 46 fF5
Gain error GERRVDD = 3.3V, TA = 25°Ctyp 0.2 %5
Gain drift vs temperature tcG-40°C < T < 125°C; VDD = 3.3Vtyp -37.5 ppm/°C5
DC power supply rejection PSRR3V < VDD < 3.6V, single-ended mode (channel vs GND); TA = 25°Ctyp 13.6 fF/V5
Full-scale range FRCAPDACCAPDAC; VDD = 3.3V, TA = 25°Ctyp 96.9 pF5
Offset drift vs. temperature TcCOFFCAPDACCAPDAC; -40°C < T < 125°C; VDD = 3.3Vtyp 30 fF5
Frequency ƒEXCITATION; VDD = 3.3V, TA = 25°Ctyp 25 kHz5
AC voltage across capacitance VACEXCITATION; VDD = 3.3V, TA = 25°Ctyp 2.4 Vpp5
Average DC voltage across capacitance VDCEXCITATION; VDD = 3.3V, TA = 25°Ctyp 1.2 V5
Driver capability DRVƒ = 25kHz, SHLDn to GND, n = 1,2; VDD = 3.3V, TA = 25°Cmax 400 pF5
Output low voltage VOLSink current 3 mA; VDD = 3.3V, TA = TJ = 25°Cmax 0.4 V5
Clock frequency(1) fSCLVDD = 3.3V, TA = TJ = 25°Cmin 10 · max 400 kHz6
Clock low time(1) tLOWVDD = 3.3V, TA = TJ = 25°Cmin 1.3 us6
Clock high time(1) tHIGHVDD = 3.3V, TA = TJ = 25°Cmin 0.6 us6
Hold time (repeated) START condition(1) tHD;STAAfter this period, the first clock pulse is generated; VDD = 3.3V, TA = TJ = 25°Cmin 0.6 us6
Set-up time for a repeated START condition(1) tSU;STAVDD = 3.3V, TA = TJ = 25°Cmin 0.6 us6
Data hold time(1) (2) tHD;DATVDD = 3.3V, TA = TJ = 25°Cmin 0 ns6
Data setup time(1) tSU;DATVDD = 3.3V, TA = TJ = 25°Cmin 100 ns6
SDA fall time(1) tfIL ≤ 3mA; CL ≤ 400pF; VDD = 3.3V, TA = TJ = 25°Cmax 300 ns6
Set-up time for STOP condition(1) tSU;STOVDD = 3.3V, TA = TJ = 25°Cmin 0.6 us6
Bus free time between a STOP and START condition(1) tBUFVDD = 3.3V, TA = TJ = 25°Cmin 1.3 us6
Data valid time(1) tVD;DATVDD = 3.3V, TA = TJ = 25°Cmax 0.9 ns6
Data valid acknowledge time(1) tVD;ACKVDD = 3.3V, TA = TJ = 25°Cmax 0.9 ns6
Pulse width of spikes that must be suppressed by the input filter(1) tSPVDD = 3.3V, TA = TJ = 25°Cmax 50 ns6

Pins, by the datasheet

10
1 SHLD1
Capacitive Input Active AC Shielding. · p. 3
2 CIN1
Capacitive input; connect measured capacitance between CIN1 and GND; leave open if unused. · p. 3
3 CIN2
Capacitive input; connect measured capacitance between CIN2 and GND; leave open if unused. · p. 3
4 CIN3
Capacitive input; connect measured capacitance between CIN3 and GND; leave open if unused. · p. 3
5 CIN4
Capacitive input; connect measured capacitance between CIN4 and GND; leave open if unused. · p. 3
6 SHLD2
Capacitive Input Active AC Shielding. · p. 3
7 GND
Ground. · p. 3
8 VDD
Power supply voltage; decouple to GND using a low impedance capacitor, for example 1uF tantalum and 0.1uF multilayer ceramic. · p. 3
9 SCL
Serial interface clock input; connect to controller clock line; requires pullup resistor if not provided elsewhere. · p. 3
10 SDA
Serial interface bidirectional data; connect to controller data line; requires pullup resistor if not provided elsewhere. · p. 3

Open-source boards using it

9See all 9
  • 2 layers130 × 24 mmEspressoSensorBoard, the printed circuit board in 3D

    EspressoSensorBoard

    jcohenadad/espresso-pimpup

    DIY project to pimp up my espresso machine to display various measures

    16 parts1MIT
  • 4 layers42 × 155 mmBefore, the printed circuit board in 3D

    Before

    alxgmpr/moisture-sensor

    Indoor capacitive soil moisture sensor - nRF54L15 + nPM1300 + FDC1004, BTHome v2 over BLE

    65 parts
  • 2 layers59 × 35.5 mmHydration Tracker, the printed circuit board in 3D

    Hydration Tracker

    Dom-Taing/Hydration-Tracker

    The goal of this product is to track how much water a user drink in a day. The sensor device would be a sleeve that can be worn onto a water bottle, it'll detect the water level in the bottle and convert that into…

    16 parts
  • 2 layers14.6 × 12.3 mmFDC1004Q Breakout, the printed circuit board in 3D

    FDC1004Q Breakout

    dfieschko/Breakouts

    A repository for breakout boards designed with KiCAD.

    4 parts4GPL-3.0
  • 4 layers42 × 155 mmNrf moisture sensor, the printed circuit board in 3D

    Nrf moisture sensor

    alxgmpr/moisture-sensor

    Indoor capacitive soil moisture sensor - nRF54L15 + nPM1300 + FDC1004, BTHome v2 over BLE

    60 parts
  • 4 layers42 × 155 mmNrf moisture sensor, the printed circuit board in 3D

    Nrf moisture sensor

    alxgmpr/moisture-sensor

    Indoor capacitive soil moisture sensor - nRF54L15 + nPM1300 + FDC1004, BTHome v2 over BLE

    62 parts
  • 4 layers42 × 155 mmNrf moisture sensor, the printed circuit board in 3D

    Nrf moisture sensor

    alxgmpr/moisture-sensor

    Indoor capacitive soil moisture sensor - nRF54L15 + nPM1300 + FDC1004, BTHome v2 over BLE

    59 parts
  • 4 layers45 × 120 mmMoisture, the printed circuit board in 3D

    Moisture

    marmbrus/circuits

    13 parts

Parts like it

6

Questions

Is there a KiCad symbol and footprint for the FDC1004DGSR?

Yes. The symbol is Sensor_Proximity:FDC1004DGS and the footprint Package_SO:MSOP-10_3x3mm_P0.5mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the FDC1004DGSR?

MSOP-10, with 10 pins. Its footprint is drawn on this page.

Where is the FDC1004DGSR datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the FDC1004DGSR?

JLCPCB lists it as part C2865994, with 7,127 in stock; the sellers' links on this page open their listings.

What can replace the FDC1004DGSR?

Parts like it in the library: the BS814A-1 by HOLTEK, the BS814C-1-10MSOP by Holtek Semicon, the IQS263B-0-MSR by Azoteq and the AS03B(AI03B) by Sam&wing. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the FDC1004DGSR?

9 boards in 6 repositories on GitHub; the most starred are listed on this page, with their KiCad files.