DRV8873SPWP
Texas InstrumentsExtended
-40℃~+125℃ 1 10A 150mΩ 15uA SPI Yes HTSSOP-24-EP Brushed DC Motor Drivers ROHS
- Part id
- ti/DRV8873SPWP
- Category
- Brushed DC Motor Drivers
- Package
- HTSSOP-24-EP
- Pins
- 25
- In stock
- 1,783 at JLCPCB (C2150662)
Overview
The DRV8873SPWP is a brushed DC Motor Driver made by Texas Instruments in a HTSSOP-24-EP package with 25 pins. -40℃~+125℃ 1 10A 150mΩ 15uA SPI Yes HTSSOP-24-EP Brushed DC Motor Drivers ROHS.
PCBKit's library has its KiCad symbol (EasyEDA_Cloud:DRV8873SPWPR, from EasyEDA) and its footprint (EasyEDA_Cloud:HTSSOP-24_L7.8-W4.4-P0.65-LS6.4-BL-EP5.2, from EasyEDA), ready for a KiCad board. 1,783 are in stock at JLCPCB (part C2150662).
Symbol
Footprint
From the datasheet
14- Supply, least
- 4.5 V · VM, recommended operating min · p. 5
- Supply, most
- 38 V · VM, recommended operating max · p. 5
- Supply, absolute maximum
- 40 V · VM, absolute maximum · p. 4
- Works from
- -40 °C · Operating ambient temperature min · p. 5
- Works up to
- 125 °C · Operating ambient temperature max · p. 5
- Junction, hottest
- 150 °C · Operating junction temperature max · p. 5
- Takes working
- 5 mA · VM operating supply current typical, VVM = 13.5 V, nSLEEP = 1, DISABLE = 0 · p. 5
- Takes at most
- 10 mA · VM operating supply current max, VVM = 13.5 V, nSLEEP = 1, DISABLE = 0 · p. 5
- Takes asleep
- 15 µA · VM sleep mode supply current typical, VVM = 13.5 V, nSLEEP = 0 · p. 5
- A pin gives at most
- 10 mA · nFAULT open drain output current absolute max · p. 4
- Current limit
- 3.85 A · Current limit threshold typical, ITRIP_LVL = 00b, VVM = 13.5 V · p. 7
- Current limit
- 5.4 A · Current limit threshold typical, ITRIP_LVL = 01b, VVM = 13.5 V · p. 7
- Current limit
- 6.5 A · Current limit threshold typical, ITRIP_LVL = 10b, VVM = 13.5 V · p. 7
- Current limit
- 7 A · Current limit threshold typical, ITRIP_LVL = 11b, VVM = 13.5 V · p. 7
What it is and has
13- Driver
- H-bridge motor driver · p. 1
- Peak current drive
- 10 A · p. 1
- Logic inputs
- 1.8 V, 3.3 V, 5 V · p. 1
- Control interface
- PH/EN · p. 1
- Control interface
- PWM (IN1/IN2) · p. 1
- Control interface
- Independent half-bridge control · p. 1
- Package
- 24 HTSSOP PowerPAD · p. 1
- Protection
- VM undervoltage lockout · p. 1
- Protection
- Charge pump undervoltage · p. 1
- Protection
- Overcurrent protection · p. 1
- Protection
- Open load detection · p. 1
- Protection
- Thermal shutdown · p. 1
- Fault indication
- nFAULT / SPI · p. 1
Around it
4- cap 47 nF
- between CPH and CPL; X7R charge pump switching capacitor. · p. 3
- cap 1-µF
- between DVDD and GND; 6.3-V ceramic bypass capacitor. · p. 3
- cap 1-µF
- between VCP and VM; 16-V ceramic charge pump capacitor. · p. 4
- cap 0.1-µF
- between VM and GND; Ceramic bypass capacitor at VM pin 13; also requires a bulk capacitor. · p. 4
Specifications
113| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Power supply voltage | VM | min -0.3 · max 40 V | 4 |
| Charge pump voltage | VCP, CPH; maximum VVM + 5.7 V | min -0.3 V | 4 |
| Charge pump switching pin | CPL; maximum VVM | min -0.3 V | 4 |
| Internal logic regulator voltage | DVDD | min -0.3 · max 5.7 V | 4 |
| Digital pin voltage | EN/IN1, PH/IN2, nSLEEP, DISABLE, nFAULT, SCLK, SDI, SDO, nSCS | min -0.3 · max 5.7 V | 4 |
| Analog pin voltage VTRIP | IPROPI1, IPROPI2 | min 0 · max 5.5 V | 4 |
| H-Bridge source pin voltage VSRC | min -0.3 · max 0.3 V | 4 | |
| Open drain output current | nFAULT | min 0 · max 10 mA | 4 |
| Push-pull output current | SDO | min 0 · max 10 mA | 4 |
| Operating junction temperature TJ | min -40 · max 150 °C | 4 | |
| Storage temperature Tstg | min -65 · max 150 °C | 4 | |
| Electrostatic discharge V(ESD) | Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins; ±2000 V | max 2000 V | 5 |
| Electrostatic discharge V(ESD) | Charged device model (CDM), per JEDEC specification JESD22-C101; corner pins (1, 12, 13, and 24); ±750 V | max 750 V | 5 |
| Electrostatic discharge V(ESD) | Charged device model (CDM), per JEDEC specification JESD22-C101; other pins; ±500 V | max 500 V | 5 |
| Power supply voltage VVM | min 4.5 · max 38 V | 5 | |
| Logic level input voltage VI | min 0 · max 5.5 V | 5 | |
| Applied PWM signal (EN/IN1, PH/IN2) fPWM | max 100 kHz | 5 | |
| Operating ambient temperature TA | min -40 · max 125 °C | 5 | |
| VM operating voltage VVM | min 4.5 · max 38 V | 5 | |
| VM operating supply current IVM | VVM = 13.5 V; nSLEEP = 1; DISABLE = 0 | typ 5 · max 10 mA | 5 |
| VM sleep mode supply current IVM(Q) | VVM = 13.5 V; nSLEEP = 0 | typ 15 · max 30 uA | 5 |
| Internal logic regulator voltage VDVDD | 2-mA load, VVM > 5.5 V | min 4.7 · typ 5 · max 5.3 V | 5 |
| Sleep time t(SLEEP) | nSLEEP low to start device shutdown | min 50 us | 5 |
| nSLEEP reset pulse t(RESET) | nSLEEP low to only clear fault registers | min 5 · max 20 us | 5 |
| Wake-up time t(WAKE) | nSLEEP high to device ready for input signals | max 1.5 ms | 5 |
| Turn-on time ton | VM > V(UVLO); nSLEEP = 1, to output transition | max 1.5 ms | 5 |
| DISABLE deglitch time t(DISABLE) | DISABLE signal transition | typ 2.5 us | 5 |
| VCP current IVCP | VVM = 13.5 V | typ 7 · max 10 mA | 5 |
| Charge pump switching frequency f(VCP) | VVM > V(UVLO); nSLEEP = 1 | typ 400 kHz | 5 |
| Input logic-low voltage VIL | EN/IN1, PH/IN2, nSLEEP, SCLK, SDI | min 0 · max 0.8 V | 6 |
| Input logic-high voltage VIH | EN/IN1, PH/IN2, nSLEEP, SCLK, SDI | min 1.6 · max 5.3 V | 6 |
| Input logic hysteresis VHYS | EN/IN1, PH/IN2, nSLEEP, SCLK, SDI | typ 150 mV | 6 |
| Input logic-low current IIL | VIN = 0 V | min -5 · max 5 uA | 6 |
| Input logic-high current IIH | VIN = 5 V | typ 50 uA | 6 |
| Internal pulldown resistance RPD | to GND | typ 100 kΩ | 6 |
| Propagation delay (EN/IN1, PH/IN2 to OUTx = 50%) tpd | SR = 000b; IO = 1 A | typ 1.2 us | 6 |
| Propagation delay (EN/IN1, PH/IN2 to OUTx = 50%) tpd | SR = 001b; IO = 1 A | typ 1.6 us | 6 |
| Propagation delay (EN/IN1, PH/IN2 to OUTx = 50%) tpd | SR = 010b; IO = 1 A | typ 2.6 us | 6 |
| Propagation delay (EN/IN1, PH/IN2 to OUTx = 50%) tpd | SR = 011b; IO = 1 A | typ 3.4 us | 6 |
| Propagation delay (EN/IN1, PH/IN2 to OUTx = 50%) tpd | SR = 100b; IO = 1 A | typ 4.1 us | 6 |
| Propagation delay (EN/IN1, PH/IN2 to OUTx = 50%) tpd | SR = 101b; IO = 1 A | typ 5.2 us | 6 |
| Propagation delay (EN/IN1, PH/IN2 to OUTx = 50%) tpd | SR = 110b; IO = 1 A | typ 7.8 us | 6 |
| Propagation delay (EN/IN1, PH/IN2 to OUTx = 50%) tpd | SR = 111b; IO = 1 A | typ 13.3 us | 6 |
| Internal pull-up resistance RPU,DIS | DISABLE to DVDD | typ 100 kΩ | 6 |
| Input logic-low voltage VIL,DIS | DISABLE | min 0 · max 0.8 V | 6 |
| Input logic-high voltage VIH,DIS | DISABLE | min 1.6 · max 5.3 V | 6 |
| Input logic-low voltage VIL,nSCS | nSCS | min 0 · max 0.8 V | 6 |
| Input logic-high voltage VIH,nSCS | nSCS | min 1.6 · max 5.3 V | 6 |
| Internal pull-up resistance RPU,nSCS | nSCS to nSLEEP | typ 450 kΩ | 6 |
| Input logic-low voltage VIL,SLEEP | nSLEEP | min 0 · max 0.8 V | 6 |
| Input logic-high voltage VIH,SLEEP | nSLEEP | min 2.7 · max 5.3 V | 6 |
| Internal pull-down resistance RPD,SDO | With respect to GND | typ 30 · max 50 Ω | 6 |
| Internal pull-up resistance RPU,SDO | With respect to nSLEEP | typ 120 · max 240 Ω | 6 |
| Output logic-low voltage VOL | IO = 2 mA; nFAULT | max 0.1 V | 6 |
| Output high-impedance leakage IOZ | VO = 5 V; nFAULT | min -2 · max 2 uA | 6 |
| High-side FET on-resistance RDS(ON) | VVM = 13.5 V; TA = 25°C; TJ = 25°C | typ 75 mΩ | 6 |
| High-side FET on-resistance RDS(ON) | VVM = 13.5 V; TA = 25°C; TJ = 150°C | typ 125 · max 155 mΩ | 6 |
| Low-side FET on-resistance RDS(ON) | VVM = 13.5 V; TA = 25°C; TJ = 25°C | typ 75 mΩ | 6 |
| Low-side FET on-resistance RDS(ON) | VVM = 13.5 V; TA = 25°C; TJ = 150°C | typ 125 · max 155 mΩ | 6 |
| Output dead time t(DEAD) | SR = 100b | typ 500 ns | 6 |
| Body diode forward voltage VF(DIODE) | IO = 1 A | typ 0.8 V | 6 |
| Sink current when OUTx = Hi-Z ISINK | nSLEEP = 0 | typ 62 uA | 7 |
| Sink current when OUTx = Hi-Z ISINK | nSLEEP = 1, DISABLE = 1 | typ 340 uA | 7 |
| Slew rate (SPI Device) OUTx 10% to 90% changing SR | IO = 1 A; SR = 000b | typ 53.2 V/us | 7 |
| Slew rate (SPI Device) OUTx 10% to 90% changing SR | IO = 1 A; SR = 001b | typ 34 V/us | 7 |
| Slew rate (SPI Device) OUTx 10% to 90% changing SR | IO = 1 A; SR = 010b | typ 18.3 V/us | 7 |
| Slew rate (SPI Device) OUTx 10% to 90% changing SR | IO = 1 A; SR = 011b | typ 13 V/us | 7 |
| Slew rate (SPI Device) OUTx 10% to 90% changing SR | IO = 1 A; SR = 100b | typ 10.8 V/us | 7 |
| Slew rate (SPI Device) OUTx 10% to 90% changing SR | IO = 1 A; SR = 101b | typ 7.9 V/us | 7 |
| Slew rate (SPI Device) OUTx 10% to 90% changing SR | IO = 1 A; SR = 110b | typ 5.3 V/us | 7 |
| Slew rate (SPI Device) OUTx 10% to 90% changing SR | IO = 1 A; SR = 111b | typ 2.6 V/us | 7 |
| Current mirror scaling k | typ 1100 A/A | 7 | |
| Current mirror scaling kERR | IO < 1 A | min -50 · max 50 mA | 7 |
| Current mirror scaling kERR | IO ≥ 1 A | min -5 · max 5 % | 7 |
| OUTx to IPROPI t(IPROPI) | VO = 2 V; SR = 000b | typ 2.2 us | 7 |
| OUTx to IPROPI t(IPROPI) | VO = 2 V; SR = 111b | typ 10.5 us | 7 |
| Current limit threshold ITRIP | ITRIP_LVL = 00b; VVM = 13.5 V | min 3.27 · typ 3.85 · max 4.43 A | 7 |
| Current limit threshold ITRIP | ITRIP_LVL = 01b; VVM = 13.5 V | min 4.6 · typ 5.4 · max 6.2 A | 7 |
| Current limit threshold ITRIP | ITRIP_LVL = 10b; VVM = 13.5 V | min 5.5 · typ 6.5 · max 7.5 A | 7 |
| Current limit threshold ITRIP | ITRIP_LVL = 11b; VVM = 13.5 V | min 5.95 · typ 7 · max 8.1 A | 7 |
| PWM off-time tOFF | TOFF = 00b | typ 20 us | 7 |
| PWM off-time tOFF | TOFF = 01b | typ 40 us | 7 |
| PWM off-time tOFF | TOFF = 10b | typ 60 us | 7 |
| PWM off-time tOFF | TOFF = 11b | typ 80 us | 7 |
| PWM blanking time tBLANK | typ 5 us | 7 | |
| VM undervoltage lockout V(UVLO) | VM falling; UVLO report | typ 4.35 · max 4.45 V | 7 |
| VM undervoltage lockout V(UVLO) | VM rising; UVLO recovery | typ 4.5 · max 4.7 V | 7 |
| VM UVLO falling deglitch time t(UVLO) | VM falling; UVLO report | typ 10 us | 7 |
| VM UVLO reset V(RST) | VM falling; UVLO report; device reset | max 4.1 V | 7 |
| Overcurrent protection trip level I(OCP) | min 10 A | 7 | |
| Overcurrent deglitch time t(OCP) | typ 3 · max 5 us | 7 | |
| Overcurrent retry time (SPI Device) t(RETRY) | OCP_TRETRY = 00b | typ 0.5 ms | 7 |
| Overcurrent retry time (SPI Device) t(RETRY) | OCP_TRETRY = 01b | typ 1 ms | 7 |
| Overcurrent retry time (SPI Device) t(RETRY) | OCP_TRETRY = 10b | typ 2 ms | 7 |
| Overcurrent retry time (SPI Device) t(RETRY) | OCP_TRETRY = 11b | typ 4 ms | 7 |
| Open load active mode VOLA | min 150 · typ 300 · max 450 mV | 7 | |
| Open load diagnostic delay time td(OL) | OL_DLY = 0b | typ 0.3 ms | 8 |
| Open load diagnostic delay time td(OL) | OL_DLY = 1b | typ 1.2 ms | 8 |
| Open load current IOL | typ 3 mA | 8 | |
| Thermal warning temperature TOTW | Die temperature (TJ) | min 140 · typ 150 · max 160 °C | 8 |
| Thermal shutdown temperature TTSD | Die Temperature (TJ) | min 165 · typ 175 · max 185 °C | 8 |
| Thermal shutdown hysteresis Thys | Die temperature (TJ) | typ 20 °C | 8 |
| SPI ready, VM > V(UVLO) t(READY) | typ 1 ms | 8 | |
| SCLK minimum period t(CLK) | min 100 ns | 8 | |
| SCLK minimum high time t(CLKH) | min 50 ns | 8 | |
| SCLK minimum low time t(CLKL) | min 50 ns | 8 | |
| SDI input setup time tsu(SDI) | min 20 ns | 8 | |
| SDI input hold time th(SDI) | min 30 ns | 8 | |
| SDO output delay time, SCLK high to SDO valid, CL = 20 pF td(SDO) | max 30 ns | 8 | |
| nSCS input setup time tsu(nSCS) | min 50 ns | 8 | |
| nSCS input hold time th(nSCS) | min 50 ns | 8 | |
| nSCS minimum high time before active low t(HI_nSCS) | min 500 ns | 8 | |
| nSCS disable time, nSCS high to SDO high impedance tdis(nSCS) | typ 10 ns | 8 |
Pins, by the datasheet
24- 1 DVDD
- 5-V internal digital-supply regulator; bypass to GND with a 6.3-V, 1-uF ceramic capacitor. · p. 3
- 2 nFAULT
- Pulled low for a fault condition; requires an external pullup resistor. · p. 4
- 3 SDO
- Push-pull serial data output; data shifts out on the rising edge of SCLK. · p. 4
- 4 SDI
- Serial data input; captured on the falling edge of SCLK. · p. 4
- 5 SCLK
- Serial clock input; serial data shifts out and is captured on the corresponding rising and falling edges. · p. 4
- 6 nSCS
- Active-low serial chip select; internal pullup to nSLEEP. · p. 4
- 7 EN/IN1
- Control input with internal pulldown to GND. · p. 3
- 8 PH/IN2
- Control input with internal pulldown to GND. · p. 4
- 9 DISABLE
- Logic high disables the H-bridge to Hi-Z; internal pullup to DVDD. · p. 3
- 10 IPROPI1
- Analog current proportional to the high-side FET current in the half bridge. · p. 3
- 11 nSLEEP
- Set low to enter low-power sleep mode. · p. 4
- 12 IPROPI2
- Analog current proportional to the high-side FET current in the half bridge. · p. 3
- 13 VM
- Motor power supply; bypass to GND with a 0.1-uF ceramic capacitor and a bulk capacitor. · p. 4
- 14 OUT2
- Half-bridge output 2; connect to the motor or load. · p. 3
- 15 OUT2
- Half-bridge output 2; connect to the motor or load. · p. 3
- 16 SRC
- Power FET source; tie to GND through a low-impedance path. · p. 4
- 17 SRC
- Power FET source; tie to GND through a low-impedance path. · p. 4
- 18 OUT1
- Half-bridge output 1; connect to the motor or load. · p. 3
- 19 OUT1
- Half-bridge output 1; connect to the motor or load. · p. 3
- 20 VM
- Motor power supply; bypass to GND with a 0.1-uF ceramic capacitor and a bulk capacitor. · p. 4
- 21 VCP
- Charge pump output; connect a 16-V, 1-uF ceramic capacitor to VM. · p. 4
- 22 CPH
- Charge pump switching node; connect a 47-nF X7R capacitor between CPH and CPL. · p. 3
- 23 CPL
- Charge pump switching node; connect a 47-nF X7R capacitor between CPH and CPL. · p. 3
- 24 GND
- Ground pin. · p. 3
Parts like it
1Questions
Is there a KiCad symbol and footprint for the DRV8873SPWP?
Yes. The symbol is EasyEDA_Cloud:DRV8873SPWPR and the footprint EasyEDA_Cloud:HTSSOP-24_L7.8-W4.4-P0.65-LS6.4-BL-EP5.2, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the DRV8873SPWP?
HTSSOP-24-EP, with 25 pins. Its footprint is drawn on this page.
Where is the DRV8873SPWP datasheet?
Texas Instruments publishes it: the Datasheet link on this page opens it.
Where can I order the DRV8873SPWP?
JLCPCB lists it as part C2150662, with 1,783 in stock; the sellers' links on this page open their listings.
What can replace the DRV8873SPWP?
Parts like it in the library: the DRV8873HPWP by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.