Skip to the content
57

DRV8301DCAR

Texas InstrumentsExtended

-40℃~+125℃ 1.7A 2.3A 20uA 25ns 25ns 6 6V~60V MOSFET Three Phase Under Voltage Protection、Over Voltage Protection、Over Current Protection、Overtemperature protection (OTP) HTSSOP-56-6mm Gate Drivers ROHS

Part id
ti/DRV8301DCAR
Category
Brushless DC (BLDC) Motor Driver
Package
HTSSOP-56-6mm
Pins
56
In stock
6,548 at JLCPCB (C98969)
Used on
8 open-source boards

Overview

The DRV8301DCAR is a brushless DC (BLDC) Motor Driver made by Texas Instruments in a HTSSOP-56-6mm package with 57 pins. -40℃~+125℃ 1.7A 2.3A 20uA 25ns 25ns 6 6V~60V MOSFET Three Phase Under Voltage Protection、Over Voltage Protection、Over Current Protection、Overtemperature protection (OTP) HTSSOP-56-6mm Gate Drivers ROHS.

PCBKit's library has its KiCad symbol (Celestial_Driver_Motor:TI DRV8301DCAR, from Altium's library) and its footprint (EasyEDA_Cloud:HTSSOP-56_L14.0-W6.0-P0.50-LS8.0-BL, from EasyEDA), ready for a KiCad board. 6,548 are in stock at JLCPCB (part C98969). 8 open-source boards in 8 repositories on GitHub use it.

Symbol

1RT_CLK2COMP3VSENSE4PWRGD5OCTW6FAULT7DTC8SCS9SDI10SDO11SCLK12DC_CAL13GVDD14CP115CP216EN_GATE23DVDD24REF25SO126SO227AVDD28AGND29PVDD149VDD_SPI50PH51PH52BST_BK53PVDD254PVDD255EN_BUCK56SS_TR57GND
Celestial_Driver_Motor:TI DRV8301DCARFrom Altium's library

Footprint

57
EasyEDA_Cloud:HTSSOP-56_L14.0-W6.0-P0.50-LS8.0-BLFrom EasyEDA

From the datasheet

17
Supply, least
6 V · PVDD1, recommended operating min · p. 7
Supply, most
60 V · PVDD1, recommended operating max · p. 7
Supply, least
3.5 V · PVDD2, recommended operating min · p. 7
Supply, absolute maximum
65 V · PVDD, absolute max relative to PGND · p. 6
Supply, absolute maximum
7 V · VDD_SPI, absolute max · p. 6
Works from
-40 °C · ambient operating min · p. 7
Works up to
125 °C · ambient operating max · p. 7
Junction, hottest
150 °C · operating junction temperature max · p. 6
Takes asleep
21.3 µA · sum of typical PVDD1 standby and PVDD2 shutdown currents · p. 8
Gives
1.5 A · integrated buck converter rated output max · p. 1
Current limit
2.7 A · buck current limit typical, VIN = 12 V, TJ = 25°C · p. 10
A pin gives at most
7 mA · nFAULT and nOCTW sinking current absolute max · p. 6
Switches at
581 kHz · buck switching frequency typical, RT = 200 kΩ · p. 10
Junction to air (DCA (HTSSOP))
30.3 K/W · junction-to-ambient thermal resistance typical · p. 7
Junction to board (DCA (HTSSOP))
17.5 K/W · junction-to-board thermal resistance typical · p. 7
Junction to case (DCA (HTSSOP))
33.5 K/W · junction-to-case top thermal resistance typical · p. 7
Edge
25 ns · Gate drive output rise time typical, CL = 1 nF, 10% to 90% · p. 11

What it is and has

15
Device
Three-phase gate driver with dual current shunt amplifiers and buck regulator · p. 1
Gate drive current
1.7-A source, 2.3-A sink · p. 1
Slew rate control
EMI reduction · p. 1
PWM input modes
6 or 3 PWM · p. 1
Current shunt amplifiers
Dual integrated · p. 1
Buck converter
Integrated, 1.5 A · p. 1
Logic interface
3.3 V and 5 V support · p. 1
SPI
Supported · p. 1
Protection
Programmable dead time control · p. 1
Protection
Programmable overcurrent protection · p. 1
Protection
GVDD overvoltage lockout · p. 1
Protection
Overtemperature warning and shutdown · p. 1
Package
HTSSOP (56), 14.00 mm × 8.10 mm nominal body · p. 1
Current shunt amplifiers
Two bidirectional low-side amplifiers · p. 26
Protection
External MOSFET overcurrent protection through VDS sensing · p. 26

Around it

3
res 47 kΩ
between nFAULT and 3-5.5 V; External pullup used for the specified high output threshold. · p. 8
res ≥ 10 kΩ
between PWRGD and VCC; RPWRGD pull-up; VCC is the logic supply to the MCU. · p. 17
cap ≥4.7 µF
between PVDD2 and GND (PowerPAD); CPVDD2; 20% ceramic, rated for PVDD2. · p. 17

Specifications

132
ParameterConditionsAs printedPage
Supply voltage VPVDDRelative to PGNDmin -0.3 · max 65 V6
Maximum supply voltage ramp rate VPVDDVoltage rising up to PVDDMAXmax 1 V/uS6
Maximum voltage between PGND and GND VPGNDmin -0.3 · max 0.3 V6
Maximum current for all digital and analog inputs IIN_MAXINH_A, INL_A, INH_B, INL_B, INH_C, INL_C, SCLK, SCS, SDI, EN_GATE, DC_CAL, DTCmin -1 · max 1 mA6
Maximum sinking current for open-drain pins (nFAULT and nOCTW Pins) ISINK_MAXmax 7 mA6
Voltage for SPx and SNx pins VOPA_INmin -0.6 · max 0.6 V6
Input voltage range for logic/digital pins VLOGICINH_A, INL_A, INH_B, INL_B, INH_C, INL_C, EN_GATE, SCLK, SDI, SCS, DC_CALmin -0.3 · max 7 V6
Maximum voltage for GVDD pin VGVDDmax 13.2 V6
Maximum voltage for AVDD pin VAVDDmax 8 V6
Maximum voltage for DVDD pin VDVDDmax 3.6 V6
Maximum voltage for VDD_SPI pin VVDD_SPImax 7 V6
Maximum reference voltage for current amplifier VREFmax 7 V6
Maximum current for REF pin IREFmax 100 uA6
Maximum operating junction temperature TJmin -40 · max 150 °C6
Storage temperature Tstgmin -55 · max 150 °C6
Electrostatic discharge V(ESD)Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins; ± ratingmax 2000 V6
Electrostatic discharge V(ESD)Charged device model (CDM), per JEDEC specification JESD22-C101, all pins; ± ratingmax 500 V6
DC supply voltage PVDD1 for normal operation VPVDD1Relative to PGNDmin 6 · max 60 V7
DC supply voltage PVDD2 for buck converter VPVDD2min 3.5 · max 60 V7
Input current of digital pins when EN_GATE is high IDIN_ENmax 100 uA7
Input current of digital pins when EN_GATE is low IDIN_DISmax 1 uA7
Maximum output capacitance on outputs of shunt amplifier CO_OPAmax 20 pF7
Dead time control resistor range. Time range is 50 ns (-GND) to 500 ns (150 kΩ) with a linear approximation. RDTCmin 0 · max 150 kΩ7
nFAULT pin sink current, open-drain IFAULTV = 0.4 Vmax 2 mA7
nFAULT pin sink current, open-drain IOCTWV = 0.4 Vmax 2 mA7
External voltage reference voltage for current shunt amplifiers VREFmin 2 · max 6 V7
Operating switching frequency of gate driver ƒgateQg(TOT) = 25 nC or total 30-mA gate drive average currentmax 200 kHz7
Total average gate drive current Igatemax 30 mA7
Ambient temperature TAmin -40 · max 125 °C7
Junction-to-ambient thermal resistance RθJADRV8301, DCA (HTSSOP), 56 PINStyp 30.3 °C/W7
Junction-to-case (top) thermal resistance RθJC(top)DRV8301, DCA (HTSSOP), 56 PINStyp 33.5 °C/W7
Junction-to-board thermal resistance RθJBDRV8301, DCA (HTSSOP), 56 PINStyp 17.5 °C/W7
Junction-to-top characterization parameter ψJTDRV8301, DCA (HTSSOP), 56 PINStyp 0.9 °C/W7
Junction-to-board characterization parameter ψJBDRV8301, DCA (HTSSOP), 56 PINStyp 7.2 °C/W7
Junction-to-case (bottom) thermal resistance RθJC(bot)DRV8301, DCA (HTSSOP), 56 PINStyp 0.9 °C/W7
High input threshold VIHINH_X, INL_X, nSCS, SDI, SCLK, EN_GATE, DC_CAL; PVDD = 6 to 60 V, TC = 25°Cmin 2 V8
Low input threshold VILINH_X, INL_X, nSCS, SDI, SCLK, EN_GATE, DC_CAL; PVDD = 6 to 60 V, TC = 25°Cmax 0.8 V8
Internal pulldown resistor for EN_GATE REN_GATEPVDD = 6 to 60 V, TC = 25°Ctyp 100 kΩ8
Internal pulldown resistor for high-side PWMs (INH_A, INH_B, and INH_C) RINH_XEN_GATE high; PVDD = 6 to 60 V, TC = 25°Ctyp 100 kΩ8
Internal pulldown resistor for low-side PWMs (INL_A, INL_B, and INL_C) RINH_XEN_GATE high; PVDD = 6 to 60 V, TC = 25°Ctyp 100 kΩ8
Internal pulldown resistor for nSCS RnSCSEN_GATE high; PVDD = 6 to 60 V, TC = 25°Ctyp 100 kΩ8
Internal pulldown resistor for SDI RSDIEN_GATE high; PVDD = 6 to 60 V, TC = 25°Ctyp 100 kΩ8
Internal pulldown resistor for DC_CAL RDC_CALEN_GATE high; PVDD = 6 to 60 V, TC = 25°Ctyp 100 kΩ8
Internal pulldown resistor for SCLK RSCLKEN_GATE high; PVDD = 6 to 60 V, TC = 25°Ctyp 100 kΩ8
Low output threshold VOLnFAULT and nOCTW; IO = 2 mA; PVDD = 6 to 60 V, TC = 25°Cmax 0.4 V8
High output threshold VOHnFAULT and nOCTW; External 47 kΩ pullup resistor connected to 3-5.5 V; PVDD = 6 to 60 V, TC = 25°Cmin 2.4 V8
Leakage Current on Open-Drain Pins When Logic High nFAULT and nOCTW) IOHPVDD = 6 to 60 V, TC = 25°Cmax 1 uA8
Gate driver Vgs voltage VGX_NORMPVDD = 8 to 60 V, Igate = 30 mA, CCP = 22 nF; TC = 25°Cmin 9.5 · max 11.5 V8
Gate driver Vgs voltage VGX_NORMPVDD = 8 to 60 V, Igate = 30 mA, CCP = 220 nF; TC = 25°Cmin 9.5 · max 11.5 V8
Gate driver Vgs voltage VGX_MINPVDD = 6 to 8 V, Igate = 15 mA, CCP = 22 nF; TC = 25°Cmin 8.8 V8
Gate driver Vgs voltage VGX_MINPVDD = 6 to 8 V, Igate = 30 mA, CCP = 220 nF; TC = 25°Cmin 8.3 V8
Maximum source current setting 1, peak Ioso1Vgs of FET equals to 2 V. REG 0x02; PVDD = 6 to 60 V, TC = 25°Ctyp 1.7 A8
Maximum sink current setting 1, peak Iosi1Vgs of FET equals to 8 V. REG 0x02; PVDD = 6 to 60 V, TC = 25°Ctyp 2.3 A8
Source current setting 2, peak Ioso2Vgs of FET equals to 2 V. REG 0x02; PVDD = 6 to 60 V, TC = 25°Ctyp 0.7 A8
Sink current setting 2, peak Iosi2Vgs of FET equals to 8 V. REG 0x02; PVDD = 6 to 60 V, TC = 25°Ctyp 1 A8
Source current setting 3, peak Ioso3Vgs of FET equals to 2 V. REG 0x02; PVDD = 6 to 60 V, TC = 25°Ctyp 0.25 A8
Sink current setting 3, peak Iosi3Vgs of FET equals to 8 V. REG 0x02; PVDD = 6 to 60 V, TC = 25°Ctyp 0.5 A8
Gate output impedence during standby mode when EN_GATE low (pins GH_x, GL_x) Rgate_offPVDD = 6 to 60 V, TC = 25°Cmin 1.6 · max 2.4 kΩ8
PVDD1 supply current, standby IPVDD1_STBEN_GATE is low. PVDD1 = 8 V; TC = 25°Ctyp 20 · max 50 uA8
PVDD1 supply current, operating IPVDD1_OPEN_GATE is high, no load on gate drive output, switching at 10 kHz, 100 nC gate charge; PVDD = 6 to 60 V, TC = 25°Ctyp 15 mA8
PVDD1 Supply current, Hi-Z IPVDD1_HIZEN_GATE is high, gate not switching; PVDD = 6 to 60 V, TC = 25°Cmin 2 · typ 5 · max 10 mA8
AVDD voltage AVDDPVDD = 8 to 60 V; TC = 25°Cmin 6 · typ 6.5 · max 7 V8
AVDD voltage AVDDPVDD = 6 to 60 V; TC = 25°Cmin 5.5 · max 6 V8
DVDD voltage DVDDPVDD = 6 to 60 V, TC = 25°Cmin 3 · typ 3.3 · max 3.6 V8
Undervoltage protection limit, PVDD VPVDD_UVPVDD falling; TC = 25°Cmax 5.9 V8
Undervoltage protection limit, PVDD VPVDD_UVPVDD rising; TC = 25°Cmax 6 V8
Undervoltage protection limit, GVDD VGVDD_UVGVDD falling; PVDD = 6 to 60 V, TC = 25°Cmax 8 V8
Overvoltage protection limit, GVDD VGVDD_OVPVDD = 6 to 60 V, TC = 25°Ctyp 16 V9
Drain-source voltage protection limit VDS_OCPVDD = 8 to 60 V; TC = 25°Cmin 0.125 · max 2.4 V9
Drain-source voltage protection limit VDS_OCPVDD = 6 to 8 V; TC = 25°C; reduced AVDD limits overcurrent protection settingsmin 0.125 · max 1.491 V9
OC sensing response time TocPVDD = 6 to 60 V, TC = 25°Ctyp 1.5 us9
nOCTW pin reporting pulse stretch length for OC event TOC_PULSEPVDD = 6 to 60 V, TC = 25°Ctyp 64 us9
Junction temperature for resetting overtemperature warning OTW_CLRPVDD = 6 to 60 Vtyp 115 °C9
Junction temperature for overtemperature warning and resetting over temperature shut down OTW_SET/OTSD_CLRPVDD = 6 to 60 Vtyp 130 °C9
Junction temperature for overtemperature shut down OTSD_SETPVDD = 6 to 60 Vtyp 150 °C9
Gain option 1 G1TC = –40°C to 125°Cmin 9.5 · typ 10 · max 10.5 V/V9
Gain option 2 G2TC = –40°C to 125°Cmin 18 · typ 20 · max 21 V/V9
Gain Option 3 G3TC = –40°C to 125°Cmin 38 · typ 40 · max 42 V/V9
Gain Option 4 G4TC = –40°C to 125°Cmin 75 · typ 80 · max 85 V/V9
Settling time to 1% tsettlingTC = 0 to 60°C, G = 10, Vstep = 2 Vtyp 300 ns9
Settling time to 1% tsettlingTC = 0 to 60°C, G = 20, Vstep = 2 Vtyp 600 ns9
Settling time to 1% tsettlingTC = 0 to 60°C, G = 40, Vstep = 2 Vtyp 1.2 us9
Settling time to 1% tsettlingTC = 0 to 60°C, G = 80, Vstep = 2 Vtyp 2.4 us9
Output swing linear range VswingTC = 25°Cmin 0.3 · max 5.7 V9
Slew rateG = 10; TC = 25°Ctyp 10 V/us9
Offset error RTI DC_offsetG = 10 with input shorted; TC = 25°Cmax 4 mV9
Offset drift RTI Drift_offsetTC = 25°C unless otherwise specifiedtyp 10 uV/C9
Input bias current IbiasTC = 25°Cmax 100 uA9
Common input mode range Vin_comTC = 25°Cmin -0.15 · max 0.15 V9
Differential input range Vin_difTC = 25°Cmin -0.3 · max 0.3 V9
Overall CMRR with gain resistor mismatch CMRR_OVCMRR at DC, gain = 10; TC = 25°Cmin 70 · typ 85 dB9
Internal undervoltage lockout threshold VUVLONo voltage hysteresis, rising and falling; TC = 25°Ctyp 2.5 V10
Shutdown supply current ISD(PVDD2)EN = 0 V, 25°C, 3.5 V ≤ VIN ≤ 60 Vtyp 1.3 · max 4 uA10
Operating: nonswitching supply current INON_SW(PVDD2)VSENSE = 0.83 V, VIN = 12 V; TC = 25°Ctyp 116 · max 136 uA10
Enable threshold voltage VEN_BUCKNo voltage hysteresis, rising and falling; TC = 25°Cmin 1.11 · typ 1.25 · max 1.36 V10
On-resistance RDS_ONVIN = 3.5 V, BOOT-PH = 3 V; TC = 25°Ctyp 300 mΩ10
Current limit threshold ILIMVIN = 12 V, TJ = 25°Cmin 1.8 · typ 2.7 A10
Thermal shutdown OTSD_BKtyp 182 °C10
Switching frequency FswRT = 200 kΩ; TC = 25°Cmin 450 · typ 581 · max 720 kHz10
VSENSE threshold PWRGDVSENSE falling; TC = 25°Ctyp 92 %10
VSENSE threshold PWRGDVSENSE rising; lower threshold; TC = 25°Ctyp 94 %10
VSENSE threshold PWRGDVSENSE rising; upper threshold; TC = 25°Ctyp 109 %10
VSENSE threshold PWRGDVSENSE falling; upper threshold; TC = 25°Ctyp 107 %10
HysteresisVSENSE falling; TC = 25°Ctyp 2 %10
Output high leakageVSENSE = VREF, V(PWRGD) = 5.5 V, 25°Ctyp 10 nA10
On resistanceI(PWRGD) = 3 mA, VSENSE < 0.79 V; TC = 25°Ctyp 50 Ω10
SPI ready after EN_GATE transitions to HIGH tSPI_READYPVDD > 6 Vtyp 5 · max 10 ms10
Minimum SPI clock period tCLKmin 100 ns10
Clock high time tCLKHSee Figure 1min 40 ns10
Clock low time tCLKLSee Figure 1min 40 ns10
SDI input data setup time tSU_SDImin 20 ns10
SDI input data hold time tHD_SDImin 30 ns10
SDO output data delay time, CLK high to SDO valid tD_SDOCL = 20 pFmax 20 ns10
SDO output data hold time tHD_SDOSee Figure 1min 40 ns10
SCS setup time tSU_SCSSee Figure 1min 50 ns10
SCS hold time tHD_SCSmin 50 ns10
SCS minimum high time before SCS active low tHI_SCSmin 40 ns10
SCS access time, SCS low to SDO out of high impedance tACCtyp 10 ns10
SCS disable time, SCS high to SDO high impedance tDIStyp 10 ns10
Positive input falling to GH_x falling tpd,If-OCL = 1 nF, 50% to 50%; over operating free-air temperature rangetyp 45 ns11
Positive input rising to GL_x falling tpd,Ir-OCL = 1 nF, 50% to 50%; over operating free-air temperature rangetyp 45 ns11
Minimum dead time after hand shaking (1) td_minOver operating free-air temperature rangemax 50 ns11
Dead time tdtpWith RDTC set to different values; over operating free-air temperature rangemin 50 · max 500 ns11
Rise time, gate drive output tGDrCL = 1 nF, 10% to 90%; over operating free-air temperature rangetyp 25 ns11
Fall time, gate drive output tGDFCL = 1 nF, 90% to 10%; over operating free-air temperature rangetyp 25 ns11
Minimum on pulse tON_MINNot including handshake communication. Hi-Z to on state, output of gate driver; over operating free-air temperature rangemax 50 ns11
Propagation delay matching between high side and low side tpd_matchOver operating free-air temperature rangemax 5 ns11
Deadtime matching tdt_matchOver operating free-air temperature rangemax 5 ns11
Start-up time, from EN_GATE active high to device ready for normal operation tpd,R_GATE-OPPVDD is up before start-up, all charge pump caps and regulator caps as in recommended condition; over operating free-air temperature rangetyp 5 · max 10 ms11
If EN_GATE goes from high to low and back to high state within quick reset time, it will only reset all faults and gate driver without powering down charge pump, current amp, and related internal voltage regulators. tpd,R_GATE-QuickMaximum low pulse time; over operating free-air temperature rangemax 10 us11
Delay, error event to all gates low tpd,E-LOver operating free-air temperature rangetyp 200 ns11
Delay, error event to nFAULT low tpd,E-FAULTOver operating free-air temperature rangetyp 200 ns11

Pins, by the datasheet

52
1 RT_CLK
Buck regulator resistor timing and external clock; connect resistor to GND (PowerPAD) with a very short trace. · p. 3
2 COMP
Buck error amplifier output and input to the output switch current comparator. · p. 3
3 VSENSE
Buck output voltage sense; inverting node of error amplifier. · p. 3
4 PWRGD
Requires an external pullup; asserts low for low buck output due to thermal shutdown, dropout, overvoltage, or EN_BUCK shutdown. · p. 3
5 nOCTW
Overcurrent and/or overtemperature warning; requires an external pullup and has SPI-programmable output mode. · p. 3
6 nFAULT
Fault report indicator; requires an external pullup resistor. · p. 3
7 DTC
Dead-time adjustment with external resistor to GND. · p. 3
8 nSCS
SPI chip select. · p. 3
9 SDI
SPI input. · p. 3
10 SDO
SPI output. · p. 3
11 SCLK
SPI clock signal. · p. 4
12 DC_CAL
High shorts shunt amplifier inputs and disconnects loads for external microcontroller DC offset calibration. · p. 4
13 GVDD
Internal gate driver voltage regulator; connect GVDD capacitor to GND. · p. 4
14 CP1
Charge pump pin 1; use a ceramic capacitor between CP1 and CP2. · p. 4
15 CP2
Charge pump pin 2; use a ceramic capacitor between CP1 and CP2. · p. 4
16 EN_GATE
Enables gate driver and current shunt amplifiers; buck is controlled through EN_BUCK. · p. 4
17 INH_A
High-side PWM input, half-bridge A. · p. 4
18 INL_A
Low-side PWM input, half-bridge A. · p. 4
19 INH_B
High-side PWM input, half-bridge B. · p. 4
20 INL_B
Low-side PWM input, half-bridge B. · p. 4
21 INH_C
High-side PWM input, half-bridge C. · p. 4
22 INL_C
Low-side PWM input, half-bridge C. · p. 4
23 DVDD
Internal 3.3-V supply output; connect capacitor to AGND; not specified to drive external circuitry. · p. 4
24 REF
Sets shunt amplifier output bias to half this pin voltage; connect to microcontroller ADC reference. · p. 4
25 SO1
Output of current amplifier 1. · p. 4
26 SO2
Output of current amplifier 2. · p. 4
27 AVDD
Internal 6-V supply output; always install capacitor to AGND; not specified to drive external circuitry. · p. 4
28 AGND
Analog ground; connect directly to GND (PowerPAD). · p. 4
29 PVDD1
Supply for gate driver, current shunt amplifier, and SPI; independent of PVDD2; connect capacitor to GND. · p. 4
30 SP2
Positive input of current amplifier 2; connect to ground side of sense resistor for best common mode rejection. · p. 4
31 SN2
Negative input of current amplifier 2. · p. 4
32 SP1
Positive input of current amplifier 1; connect to ground side of sense resistor for best common mode rejection. · p. 4
33 SN1
Negative input of current amplifier 1. · p. 4
34 SL_C
Low-side MOSFET source, half-bridge C; low-side VDS measured between this pin and SH_C. · p. 4
35 GL_C
Low-side MOSFET gate drive, half-bridge C. · p. 4
36 SH_C
High-side MOSFET source, half-bridge C; high-side VDS measured between this pin and PVDD1. · p. 4
37 GH_C
High-side MOSFET gate drive, half-bridge C. · p. 4
38 BST_C
Bootstrap capacitor pin for half-bridge C. · p. 4
39 SL_B
Low-side MOSFET source, half-bridge B; low-side VDS measured between this pin and SH_B. · p. 4
40 GL_B
Low-side MOSFET gate drive, half-bridge B. · p. 4
41 SH_B
High-side MOSFET source, half-bridge B; high-side VDS measured between this pin and PVDD1. · p. 4
42 GH_B
High-side MOSFET gate drive, half-bridge B. · p. 4
43 BST_B
Bootstrap capacitor pin for half-bridge B. · p. 4
44 SL_A
Low-side MOSFET source, half-bridge A; low-side VDS measured between this pin and SH_A. · p. 4
45 GL_A
Low-side MOSFET gate drive, half-bridge A. · p. 4
46 SH_A
High-side MOSFET source, half-bridge A; high-side VDS measured between this pin and PVDD1. · p. 4
47 GH_A
High-side MOSFET gate drive, half-bridge A. · p. 4
49 VDD_SPI
VDD_SPI supply pin. · p. 3
53 PVDD2
Buck converter supply. · p. 3
54 PVDD2
Buck converter supply. · p. 3
55 EN_BUCK
Controls the buck converter. · p. 3
57 GND
PowerPAD ground. · p. 3

Ordering codes, by the datasheet

6
DRV8301DCA
HTSSOP (DCA) | 56 · 35 | TUBE; operating temperature -40 to 125 °C · p. 32
DRV8301DCA.A
HTSSOP (DCA) | 56 · 35 | TUBE; operating temperature -40 to 125 °C · p. 32
DRV8301DCAR
HTSSOP (DCA) | 56 · 2000 | LARGE T&R; operating temperature -40 to 125 °C · p. 32
DRV8301DCAR.A
HTSSOP (DCA) | 56 · 2000 | LARGE T&R; operating temperature -40 to 125 °C · p. 32
DRV8301DCARG4
HTSSOP (DCA) | 56 · 2000 | LARGE T&R; operating temperature -40 to 125 °C · p. 32
DRV8301DCARG4.A
HTSSOP (DCA) | 56 · 2000 | LARGE T&R; operating temperature -40 to 125 °C · p. 32

Open-source boards using it

8
  • 4 layers58 × 50 mmBldc motor cntroller, the printed circuit board in 3D

    Bldc motor cntroller

    azmat-bilal/bldc_motor_controller_pcb

    A Brushless DC Motor controller board. The design is inspired and is compatible with Odrive project (https://github.com/madcowswe/ODriveHardware) except that this one has a single channel.

    146 parts112MIT
  • 4 layers84.5 × 60 mmBldc driver, the printed circuit board in 3D

    Bldc driver

    koson/spel-bldc-esc

    Open-source BLDC motor electronic speed controller (yet another)

    100 parts4
  • 4 layers78 × 94 mmVesc6, the printed circuit board in 3D

    Vesc6

    PaulReichhold/vesc_6_dual_couch

    266 parts2
  • 4 layers46 × 2 mmEsp bldc foc, the printed circuit board in 3D

    Esp bldc foc

    keionbis/Brushless_robot_arm_controler

    126 parts1
  • 4 layers72.6 × 72.6 mmFOC V1 PCB, the printed circuit board in 3D

    FOC V1 PCB

    arthur-wirjo/FOC_v1_project

    A custom-designed, 60V 50A Field Oriented Control (FOC) BLDC motor controller built from scratch. Designed for high-performance robotics, featuring a 4-layer power PCB, isolated USB telemetry, and CAN bus communication.

    95 partsMIT
  • 4 layers53 × 70 mmODrive, the printed circuit board in 3D

    ODrive

    Sasasu/ODrive

    162 parts
  • 4 layers80 × 50 mmVesc6, the printed circuit board in 3D

    Vesc6

    DavidTheFighter/rocketry

    122 partsMIT

Parts like it

2

Questions

Is there a KiCad symbol and footprint for the DRV8301DCAR?

Yes. The symbol is Celestial_Driver_Motor:TI DRV8301DCAR and the footprint EasyEDA_Cloud:HTSSOP-56_L14.0-W6.0-P0.50-LS8.0-BL, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the DRV8301DCAR?

HTSSOP-56-6mm, with 57 pins. Its footprint is drawn on this page.

Where is the DRV8301DCAR datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the DRV8301DCAR?

JLCPCB lists it as part C98969, with 6,548 in stock; the sellers' links on this page open their listings.

What can replace the DRV8301DCAR?

Parts like it in the library: the DRV8302DCA by Texas Instruments and the TPIC2050RDFD by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the DRV8301DCAR?

8 boards in 8 repositories on GitHub; the most starred are listed on this page, with their KiCad files.