Skip to the content

DRV2625YFF

Texas InstrumentsExtended

-40℃~+85℃ 0V~400mV 1.41V 2 2.5mA 2.7V~5.5V Half-Bridge Under Voltage Protection、Over Current Protection、Overtemperature protection (OTP)、- DSBGA-9 Gate Drivers ROHS

Part id
ti/DRV2625YFF
Category
Brushed DC Motor Drivers
Package
DSBGA-9
Pins
9
In stock
281 at JLCPCB (C553134)
Used on
6 open-source boards

Overview

The DRV2625YFF is a brushed DC Motor Driver made by Texas Instruments in a DSBGA-9 package with 9 pins. -40℃~+85℃ 0V~400mV 1.41V 2 2.5mA 2.7V~5.5V Half-Bridge Under Voltage Protection、Over Current Protection、Overtemperature protection (OTP)、- DSBGA-9 Gate Drivers ROHS.

PCBKit's library has its KiCad symbol (EasyEDA_Cloud:DRV2625YFFR, from EasyEDA) and its footprint (EasyEDA_Cloud:DSBGA-9_L1.4-W1.3-R3-C3-P0.40-BL, from EasyEDA), ready for a KiCad board. 281 are in stock at JLCPCB (part C553134). 6 open-source boards in 1 repository on GitHub use it.

Symbol

C2VDDB3GNDA2REGC3OUT-A3OUT+B1SDAC1SCLA1TRIG/INTZB2NRST
EasyEDA_Cloud:DRV2625YFFRFrom EasyEDA

Footprint

EasyEDA_Cloud:DSBGA-9_L1.4-W1.3-R3-C3-P0.40-BLFrom EasyEDA

From the datasheet

12
Supply, least
2.7 V · VDD, recommended operating min · p. 4
Supply, most
5.5 V · VDD, recommended operating max · p. 4
Supply, absolute maximum
6 V · VDD, absolute max · p. 4
Works from
-40 °C · Operating free-air temperature min · p. 4
Works up to
85 °C · Operating free-air temperature max · p. 4
Junction, hottest
150 °C · Operating junction temperature max · p. 4
Takes working
2.5 mA · Quiescent current typical, NRST = VDD, idle mode, no signal · p. 5
Takes asleep
105 nA · Shutdown current typical, V(NRST) = 0 V · p. 5
Takes asleep
1.55 µA · Standby current typical, V(NRST) = VDD · p. 5
Junction to air (DSBGA)
107 K/W · Junction-to-ambient thermal resistance · p. 4
Junction to case (DSBGA)
0.9 K/W · Junction-to-case top thermal resistance · p. 4
Junction to board (DSBGA)
18.1 K/W · Junction-to-board thermal resistance · p. 4

What it is and has

9
Actuator support
ERM and LRA · p. 10
Package
DSBGA, 9 pins, YFF · p. 3
Waveform sequencer
Built-in library and loopable waveform sequencer · p. 1
Playback
Real-time playback (RTP) mode · p. 1
Waveform shapes
Sine-wave or square-wave in LRA open-loop mode · p. 13
Protection
Thermal and over-current protection · p. 16
Brownout protection
On-chip brownout protection · p. 17
Actuator diagnostics
Open and short detection · p. 13
I2C watchdog
Automatic protocol reset after 4.33 ms · p. 16

Around it

2
cap 0.1-µF
between VDD and GND; Required supply capacitor. · p. 3
cap 0.1-µF
between REG and GND; Required regulator output capacitor. · p. 3

Specifications

46
ParameterConditionsAs printedPage
Supply Voltage VDDover operating free-air temperature rangemin -0.3 · max 6 V4
Input voltage NRSTover operating free-air temperature rangemin -0.3 · max 6 V4
Input voltage SDAover operating free-air temperature rangemin -0.3 · max 6 V4
Input voltage SCLover operating free-air temperature rangemin -0.3 · max 6 V4
Input voltage TRIG/INTZover operating free-air temperature rangemin -0.3 · max 6 V4
Operating free-air temperature range TAmin -40 · max 85 °C4
Operating junction temperature range TJmin -40 · max 150 °C4
Storage temperature Tstgmin -65 · max 150 °C4
Electrostatic discharge V(ESD)Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pinsmin -1500 · max 1500 V4
Electrostatic discharge V(ESD)Charged device model (CDM), per JEDEC specification JESD22-C101, all pinsmin -500 · max 500 V4
Supply voltage VDDover operating free-air temperature rangemin 2.7 · max 5.5 V4
Load impedance RLover operating free-air temperature rangemin 8 Ω4
Load capacitance CLover operating free-air temperature rangemax 100 pF4
LRA frequency ƒ(LRA)over operating free-air temperature rangemin 45 · max 300 Hz4
Junction-to-ambient thermal resistance RθJADRV2625, DSBGA, 9 PINStyp 107 °C/W4
Junction-to-case (top) thermal resistance RθJC(top)DRV2625, DSBGA, 9 PINStyp 0.9 °C/W4
Junction-to-board thermal resistance RθJBDRV2625, DSBGA, 9 PINStyp 18.1 °C/W4
Junction-to-top characterization parameter ψJTDRV2625, DSBGA, 9 PINStyp 3.8 °C/W4
Junction-to-board characterization parameter ψJBDRV2625, DSBGA, 9 PINStyp 18.1 °C/W4
Voltage at the REG pin V(REG)TA = 25 °C, VDD = 3.6 Vtyp 1.84 V5
Digital low-level input current IILTA = 25 °C; NRST, TRIG/INTZ, SDA, SCL; VDD = 5.5 V, VI = 0 Vmax 100 nA5
Digital high-level input current IIHTA = 25 °C; SDA, SCL; VDD = 5.5 V, VI = VDDmax 0.1 uA5
Digital high-level input current IIHTA = 25 °C; NRST; VDD = 5.5 V, VI = VDDmax 1 uA5
Digital high-level input current IIHTA = 25 °C; TRIG/INTZ; VDD = 5.5 V, VI = VDDtyp 2.7 · max 3.5 uA5
Digital low-level input voltage VILTA = 25 °C, VDD = 3.6 V; NRST, TRIG/INTZ, SDA, SCLmax 0.4 V5
Digital high-level input voltage VIHTA = 25 °C, VDD = 3.6 V; NRST, TRIG/INTZ, SDA, SCLmin 1.41 V5
Digital low-level output voltage VOLTA = 25 °C, VDD = 3.6 V; TRIG/INTZ, SDA; 3-mA sink currentmax 0.4 V5
Drain-source on-state resistance (LS + HS) RDS(on)TA = 25 °C, VDD = 3.6 Vtyp 0.75 Ω5
Shutdown current I(SD)TA = 25 °C, VDD = 3.6 V; V(NRST) = 0 Vtyp 105 · max 180 nA5
Standby current I(STBY)TA = 25 °C, VDD = 3.6 V; V(NRST) = VDD; In stand-by modetyp 1.55 · max 2 uA5
Quiescent current I(Q)TA = 25 °C, VDD = 3.6 V; V(NRST) = VDD; In idle mode - no signaltyp 2.5 mA5
Output impedance in shutdown ZO(SD)TA = 25 °C, VDD = 3.6 V; OUT+ to GND, OUT– to GNDmin 15 kΩ5
Output impedance in standby ZO(STBY)TA = 25 °C, VDD = 3.6 V; OUT+ to GND, OUT– to GNDmin 15 kΩ5
Load impedance threshold for over-current detection ZLOAD(th)TA = 25 °C, VDD = 3.6 V; OUT+ to GND, OUT– to GNDmin 4 Ω5
Frequency at the SCL pin with no wait states ƒ(SCL)TA = 25 °C, VDD = 3.6 Vmax 400 kHz5
Pulse duration, SCL high tw(H)TA = 25 °C, VDD = 3.6 Vmin 0.6 us5
Pulse duration, SCL low tw(L)TA = 25 °C, VDD = 3.6 Vmin 1.3 us5
Setup time, SDA to SCL tsu(1)TA = 25 °C, VDD = 3.6 Vmin 100 ns5
Hold time, SCL to SDA th(1)TA = 25 °C, VDD = 3.6 Vmin 10 ns5
Bus free time between stop and start condition t(BUF)TA = 25 °C, VDD = 3.6 Vmin 1.3 us5
Setup time, SCL to start condition tsu(2)TA = 25 °C, VDD = 3.6 Vmin 0.6 us5
Hold time, start condition to SCL th(2)TA = 25 °C, VDD = 3.6 Vmin 0.6 us5
Setup time, SCL to stop condition tsu(3)TA = 25 °C, VDD = 3.6 Vmin 0.6 us5
Device startup time t(on)TA = 25 °C, VDD = 3.6 V; from shutdown standbytyp 1 ms5
Waveform startup time t(start)TA = 25 °C, VDD = 3.6 V; from trigger to output signaltyp 1 ms5
PWM output frequency (in OUT+ and OUT-) fO(PWM)TA = 25 °C, VDD = 3.6 Vtyp 20.5 kHz5

Pins, by the datasheet

9
C2 VDD
Supply input (2.7 V to 5.5 V); a 0.1-uF capacitor is required. · p. 3
B3 GND
Supply ground. · p. 3
A2 REG
1.8 V regulator output; a 0.1-uF capacitor is required. · p. 3
C3 OUT-
Negative haptic driver differential output. · p. 3
A3 OUT+
Positive haptic driver differential output. · p. 3
B1 SDA
I2C data. · p. 3
C1 SCL
I2C clock. · p. 3
A1 TRIG/INTZ
Selectable input trigger pulse, input enable, or output interrupt; internal pull-down; connect to ground if unused. · p. 3
B2 NRST
Device reset pin for shutdown mode; connect to VDD if unused; no internal pull-up or pull-down. · p. 3

Open-source boards using it

6
  • 2 layers141 × 90.9 mmHaptic bracelet, the printed circuit board in 3D

    Haptic bracelet

    earlynerd/ELRS-haptics

    Battery-powered attitude feedback for FPV flying, with eight haptic actuators around each wrist. An ESP32-C6 receives telemetry over ESP-NOW and controls eight M2003FC1AE/DRV2625 pods using the music robot's UART ring…

    269 parts
  • 4 layers21 × 55.9 mmBefore five pad, the printed circuit board in 3D

    Before five pad

    earlynerd/ELRS-haptics

    Battery-powered attitude feedback for FPV flying, with eight haptic actuators around each wrist. An ESP32-C6 receives telemetry over ESP-NOW and controls eight M2003FC1AE/DRV2625 pods using the music robot's UART ring…

    93 parts
  • 4 layers21 × 55.9 mmBefore pod symmetry, the printed circuit board in 3D

    Before pod symmetry

    earlynerd/ELRS-haptics

    Battery-powered attitude feedback for FPV flying, with eight haptic actuators around each wrist. An ESP32-C6 receives telemetry over ESP-NOW and controls eight M2003FC1AE/DRV2625 pods using the music robot's UART ring…

    80 parts
  • 4 layers21 × 55.9 mmBefore simple usb, the printed circuit board in 3D

    Before simple usb

    earlynerd/ELRS-haptics

    Battery-powered attitude feedback for FPV flying, with eight haptic actuators around each wrist. An ESP32-C6 receives telemetry over ESP-NOW and controls eight M2003FC1AE/DRV2625 pods using the music robot's UART ring…

    93 parts
  • 4 layers17 × 35 mmPod-6, the printed circuit board in 3D

    Pod-6

    earlynerd/ELRS-haptics

    Battery-powered attitude feedback for FPV flying, with eight haptic actuators around each wrist. An ESP32-C6 receives telemetry over ESP-NOW and controls eight M2003FC1AE/DRV2625 pods using the music robot's UART ring…

    23 parts
  • 4 layers20 × 46 mmSatellite, the printed circuit board in 3D

    Satellite

    earlynerd/ELRS-haptics

    Battery-powered attitude feedback for FPV flying, with eight haptic actuators around each wrist. An ESP32-C6 receives telemetry over ESP-NOW and controls eight M2003FC1AE/DRV2625 pods using the music robot's UART ring…

    28 parts

Parts like it

2

Questions

Is there a KiCad symbol and footprint for the DRV2625YFF?

Yes. The symbol is EasyEDA_Cloud:DRV2625YFFR and the footprint EasyEDA_Cloud:DSBGA-9_L1.4-W1.3-R3-C3-P0.40-BL, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the DRV2625YFF?

DSBGA-9, with 9 pins. Its footprint is drawn on this page.

Where is the DRV2625YFF datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the DRV2625YFF?

JLCPCB lists it as part C553134, with 281 in stock; the sellers' links on this page open their listings.

What can replace the DRV2625YFF?

Parts like it in the library: the DRV2624YFF by Texas Instruments and the AW86224AFCR by AWINIC. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the DRV2625YFF?

6 boards in 1 repository on GitHub; the most starred are listed on this page, with their KiCad files.