
BQ29700DSE
Texas InstrumentsExtended
-40℃~+85℃ 1 2.8V 300mV~8V 4uA Lithium Battery Not supported Overcharge protection、Over-discharge protection、Overcurrent Protection、Short-Circuit Protection Protection IC Support WSON-6(1.5x1.5) Battery Management ROHS
- Part id
- ti/BQ29700DSE
- Category
- Battery Management
- Package
- WSON-6(1.5x1.5)
- Pins
- 6
- In stock
- 1,389 at JLCPCB (C2876282)
- Used on
- 9 open-source boards
Overview
The BQ29700DSE is a battery Management made by Texas Instruments in a WSON-6(1.5x1.5) package with 6 pins. -40℃~+85℃ 1 2.8V 300mV~8V 4uA Lithium Battery Not supported Overcharge protection、Over-discharge protection、Overcurrent Protection、Short-Circuit Protection Protection IC Support WSON-6(1.5x1.5) Battery Management ROHS.
PCBKit's library has its KiCad symbol (dk_PMIC-Battery-Management:BQ29700DSET, from Digikey) and its footprint (Package_SON:WSON-6_1.5x1.5mm_P0.5mm, from KiCad's library), ready for a KiCad board. 1,389 are in stock at JLCPCB (part C2876282). 9 open-source boards in 9 repositories on GitHub use it.
Symbol
Footprint
From the datasheet
12- Supply, least
- 300 mV · BAT, recommended operating min · p. 5
- Supply, most
- 8 V · BAT, recommended operating max · p. 5
- Supply, absolute maximum
- 12 V · BAT, absolute maximum · p. 4
- Works from
- -40 °C · Operating ambient temperature min · p. 5
- Works up to
- 85 °C · Operating ambient temperature max · p. 5
- Takes working
- 4 µA · BAT, NORMAL mode typical, BAT = 3.8V, V– = 0V · p. 5
- Takes at most
- 5.5 µA · BAT, NORMAL mode max, BAT = 3.8V, V– = 0V · p. 5
- Takes asleep
- 100 nA · BAT, power down mode max, BAT = V– = 1.5V · p. 5
- Junction to air (DSE (WSON))
- 250 K/W · Junction-to-ambient thermal resistance max, recommended operating conditions · p. 5
- Junction to air (DSE (WSON))
- 190.5 K/W · High K junction-to-ambient thermal resistance · p. 5
- Junction to case (DSE (WSON))
- 94.9 K/W · Junction-to-case(top) thermal resistance · p. 5
- Junction to board (DSE (WSON))
- 149.3 K/W · Junction-to-board thermal resistance · p. 5
What it is and has
12- Battery chemistry
- Single-cell Li-Ion and Li-Polymer · p. 1
- FET drive
- CHG and DSG FET drive output · p. 1
- Protection
- Overcharge detection (OVP) · p. 1
- Protection
- Over-discharge detection (UVP) · p. 1
- Protection
- Charge overcurrent detection (OCC) · p. 1
- Protection
- Discharge overcurrent detection (OCD) · p. 1
- Protection
- Load short-circuit detection (SCP) · p. 1
- Charging
- Zero voltage charging for depleted battery · p. 1
- Fault protection configuration
- Factory programmed thresholds · p. 1
- Package
- 6-pin DSE, 1.50mm × 1.50mm × 0.75mm · p. 1
- BQ29700 fault thresholds and delays
- OVP 4.275 V, 1.25 sec; UVP 2.800 V, 144 ms; OCC –0.100 V, 8 ms; OCD 0.100 V, 20 ms; SCD 0.5 V, 250 µs · p. 3
- Input voltage range
- pack+: VSS – 0.3V to 12V · p. 1
Specifications
39| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Input voltage: BAT | min -0.3 · max 12 V | 4 | |
| Operating temperature: TFUNC TFUNC | min -40 · max 85 °C | 4 | |
| Storage temperature, Tstg Tstg | min -55 · max 150 °C | 4 | |
| Electrostatic Discharge VESD | Human body model (HBM), per ANSI/ESDA/JEDEC JS–001, all pins; rating ±2000 V | max 2000 V | 4 |
| Positive input voltage: BAT | min -0.3 · max 8 V | 5 | |
| Operating temperature: TAmb TAmb | min -40 · max 85 °C | 5 | |
| Storage temperature: TS TS | min -55 · max 150 °C | 5 | |
| Lead temperature (soldering 10s) | Soldering 10s | max 300 °C | 5 |
| Thermal resistance junction to ambient, θJA θJA | max 250 °C/W | 5 | |
| Junction-to-ambient thermal resistance RθJA, High K | BQ297xx, DSE (WSON); table header states 12 PINS | typ 190.5 °C/W | 5 |
| Junction-to-case(top) thermal resistance RθJC(top) | BQ297xx, DSE (WSON); table header states 12 PINS | typ 94.9 °C/W | 5 |
| Junction-to-board thermal resistance RθJB | BQ297xx, DSE (WSON); table header states 12 PINS | typ 149.3 °C/W | 5 |
| Junction-to-top characterization parameter ψJT | BQ297xx, DSE (WSON); table header states 12 PINS | typ 6.4 °C/W | 5 |
| Junction-to-board characterization parameter ψJB | BQ297xx, DSE (WSON); table header states 12 PINS | typ 152.8 °C/W | 5 |
| Device operating range VBAT | BAT – VSS | min 1.5 · max 8 V | 5 |
| Device operating range VBAT | BAT – V– | min 1.5 · max 28 V | 5 |
| Current consumption in NORMAL mode INORMAL | BAT = 3.8V, V– = 0V | typ 4 · max 5.5 uA | 5 |
| Current consumption in power down mode IPower_down | BAT = V– = 1.5V | max 0.1 uA | 5 |
| Charge FET low output VOL | IOL = 30uA, BAT = 3.8V | typ 0.4 · max 0.5 V | 5 |
| Charge FET high output VOH | IOH = –30uA, BAT = 3.8V | min 3.4 · typ 3.7 V | 5 |
| Discharge FET low output VOL | IOL = 30uA, BAT = 2V | typ 0.2 · max 0.5 V | 5 |
| Discharge FET high output VOH | IOH = –30uA, BAT = 3.8V | min 3.4 · typ 3.7 V | 5 |
| Resistance between V– and VBAT RV–D | VBAT = 1.8V, V– = 0V | min 100 · typ 300 · max 550 kΩ | 5 |
| Current sink on V– to VSS IV–S | VBAT = 3.8V | min 8 · max 24 uA | 5 |
| 0V battery charging start voltage V0CHG | 0V battery charging function allowed | min 1.7 V | 6 |
| 0V battery charging inhibit voltage threshold V0INH | 0V battery charging function disallowed | max 0.75 V | 6 |
| Overcharge detection voltage VOVP | Factory Device Configuration: 3.85V to 4.60V in 50mV steps; TA = 25°C; threshold tolerance | min -10 · max 10 mV | 6 |
| Overcharge detection voltage VOVP | Factory Device Configuration: 3.85V to 4.60V in 50mV steps; TA = 0°C to 60°C; threshold tolerance | min -20 · max 20 mV | 6 |
| Overcharge release hysteresis voltage VOVP–Hys | 100mV and (VSS – V–) > OCC (min) for release, TA = 25°C; tolerance | min -20 · max 20 mV | 6 |
| Over-discharge detection voltage VUVP | Factory Device Configuration: 2.00V to 2.80V in 50mV steps, TA = 25°C; threshold tolerance | min -50 · max 50 mV | 6 |
| Over-discharge release hysteresis voltage VUVP+Hys | 100mV and (BAT – V–) > 1V for release, TA = 25°C; tolerance | min -50 · max 50 mV | 6 |
| Discharging overcurrent detection voltage VOCD | Factory Device Configuration: 90mV to 200mV in 5mV steps; TA = 25°C; threshold tolerance | min -10 · max 10 mV | 6 |
| Discharging overcurrent detection voltage VOCD | Factory Device Configuration: 90mV to 200mV in 5mV steps; TA = –40°C to 85°C; threshold tolerance | min -15 · max 15 mV | 6 |
| Release of discharging overcurrent detection voltage Release of VOCD | Release when BAT – V– > 1V | typ 1 V | 6 |
| Charging overcurrent detection voltage VOCC | Factory Device Configuration: –45mV to –155mV in 5mV steps; TA = 25°C; threshold tolerance | min -10 · max 10 mV | 6 |
| Charging overcurrent detection voltage VOCC | Factory Device Configuration: –45mV to –155mV in 5mV steps; TA = –40°C to 85°C; threshold tolerance | min -15 · max 15 mV | 6 |
| Release of overcurrent detection voltage Release of VOCC | Release when VSS – V– ≥ OCC (min) | typ 40 mV | 6 |
| Short Circuit detection voltage VSCC | Factory Device Configuration: 300mV, 400mV, 500mV, 600mV; TA = 25°C; threshold tolerance | min -100 · max 100 mV | 6 |
| Release of Short Circuit detection voltage VSCCR | Release when BAT – V– ≥ 1V | typ 1 V | 6 |
Pins, by the datasheet
6- 1 NC
- No Connection (electrically open). · p. 3
- 2 COUT
- Gate Drive Output for Charge FET. · p. 3
- 3 DOUT
- Gate Drive Output for Discharge FET. · p. 3
- 4 VSS
- Ground pin. · p. 3
- 5 BAT
- VDD pin. · p. 3
- 6 V–
- Input pin for charger negative voltage. · p. 3
- 8 layers100 × 100 mm

- 2 layers56 × 6.2 mm

- 2 layers

- 4 layers42 × 100 mm

- 2 layers23 × 56 mm

- 4 layers

Trackball ball
ntindle/trackball
Ultimate Mouse: fully custom trackball with a free-spinning active ball (capacitive touch ring, nRF52810, inductive charging) and a dual-PMW3360 base (nRF52840, USB-C, HID + custom driver). No mechanical wheel.
92 parts1 - 4 layers42 × 46 mm

Chickensticks
npgo22/APRL-Electrical-New
To use the board templates, set KICADUSERTEMPLATEDIR by:
73 parts - 2 layers40.8 × 54.8 mm

Parts like it
8BQ29706DSE
WSON-6(1.5x1.5)-40℃~+85℃ 1 1.5V~8V 2.5V 4uA Lithium Battery Not supported Protection IC Support WSON-6(1.5x1.5) Battery Management ROHSTexas InstrumentsBattery ManagementBQ29703DSE
WSON-6(1.5x1.5)-40℃~+85℃ 1 1.5V~8V 2.3V 4.425V 4uA Lithium Battery Not supported Protection IC Support WSON-6(1.5x1.5) Battery Management ROHSTexas InstrumentsBattery ManagementBQ29707DSE
WSON-6(1.5x1.5)-40℃~+85℃ 1 1.5V~8V 2.8V 4uA Lithium Battery Not supported Protection IC Support WSON-6(1.5x1.5) Battery Management ROHSTexas InstrumentsBattery ManagementBQ29716DSE
WSON-6(1.5x1.5)-40℃~+85℃ 1 WSON-6(1.5x1.5) Battery Management ROHSTexas InstrumentsBattery ManagementBQ29718DSE
WSON-6(1.5x1.5)-40℃~+85℃ 1 2.5V 300mV~8V 4uA Lithium Battery Not supported Protection IC Support WSON-6(1.5x1.5) Battery Management ROHSTexas InstrumentsBattery ManagementBQ29733DSE
WSON-6(1.5x1.5)-40℃~+85℃ 1 1.5V~8V 2.8V 4uA Lithium Battery Not supported Protection IC Support WSON-6(1.5x1.5) Battery Management ROHSTexas InstrumentsBattery ManagementBQ29702DSE
WSON-6(1.5x1.5)-40℃~+85℃ 1 1.5V~8V 2.8V 4uA Lithium Battery Not supported Protection IC Support WSON-6(1.5x1.5) Battery Management ROHSTexas InstrumentsBattery ManagementBQ29701DSE
WSON-6(1.5x1.5)-40℃~+85℃ 1 2.3V 300mV~8V 4uA Lithium Battery Not supported Protection IC Support WSON-6(1.5x1.5) Battery Management ROHSTexas InstrumentsBattery Management
Questions
Is there a KiCad symbol and footprint for the BQ29700DSE?
Yes. The symbol is dk_PMIC-Battery-Management:BQ29700DSET and the footprint Package_SON:WSON-6_1.5x1.5mm_P0.5mm, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the BQ29700DSE?
WSON-6(1.5x1.5), with 6 pins. Its footprint is drawn on this page.
Where is the BQ29700DSE datasheet?
Texas Instruments publishes it: the Datasheet link on this page opens it.
Where can I order the BQ29700DSE?
JLCPCB lists it as part C2876282, with 1,389 in stock; the sellers' links on this page open their listings.
What can replace the BQ29700DSE?
Parts like it in the library: the BQ29706DSE by Texas Instruments, the BQ29703DSE by Texas Instruments, the BQ29707DSE by Texas Instruments and the BQ29716DSE by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.
Which open-source boards use the BQ29700DSE?
9 boards in 9 repositories on GitHub; the most starred are listed on this page, with their KiCad files.