Skip to the content
37

BQ25756ERRVR

Texas InstrumentsExtended

-40℃~+125℃ 17uA 1~7 20A 4.2V~36V Charging IC I2C Lithium Battery、LiFePO4 Battery Support VQFN-36-EP(6x5) Battery Management ROHS

Part id
ti/BQ25756ERRVR
Category
Battery Management
Package
VQFN-36-EP(6x5)
Pins
37
In stock
101 at JLCPCB (C22427194)
Used on
4 open-source boards

Overview

The BQ25756ERRVR is a battery Management made by Texas Instruments in a VQFN-36-EP(6x5) package with 37 pins. -40℃~+125℃ 17uA 1~7 20A 4.2V~36V Charging IC I2C Lithium Battery、LiFePO4 Battery Support VQFN-36-EP(6x5) Battery Management ROHS.

PCBKit's library has its KiCad symbol (BQ25756E:BQ25756E, from Antmicro) and its footprint (qfn-36-1ep-5x6mm-p0-5mm-ep3-6x4-6mm:QFN-36-1EP_5x6mm_P0.5mm_EP3.6x4.6mm, from Antmicro), ready for a KiCad board. 101 are in stock at JLCPCB (part C22427194). 4 open-source boards in 3 repositories on GitHub use it.

Symbol

1SCL2SDA3INT4STAT15STAT26PG7CE8TS9ICHG10ILIM_HIZ11FBG12FB13SRN14SRP17PGND18SW219HIDRV220BTST221LODRV223DRV_SUP24REGN25LODRV126BTST127HIDRV128SW129ACN30ACP32VAC34ACUV35ACOV36FSW_SYNC37EPAD
BQ25756E:BQ25756EFrom Antmicro

Footprint

37
qfn-36-1ep-5x6mm-p0-5mm-ep3-6x4-6mm:QFN-36-1EP_5x6mm_P0.5mm_EP3.6x4.6mmFrom Antmicro

From the datasheet

17
Supply, least
4.2 V · VAC, recommended operating min · p. 8
Supply, most
36 V · VAC, recommended operating max · p. 8
Supply, least
4 V · DRV_SUP, direct drive recommended operating min · p. 8
Supply, most
12 V · DRV_SUP, direct drive recommended operating max · p. 8
Supply, absolute maximum
60 V · VAC, absolute max · p. 7
Works from
-40 °C · ambient temperature min · p. 8
Works up to
105 °C · ambient temperature max · p. 8
Junction, hottest
150 °C · junction temperature absolute max · p. 7
Takes working
750 µA · VAC quiescent input current, not switching, typical · p. 9
Takes asleep
17 µA · battery quiescent current, VAC = 0 V, ADC disabled, typical · p. 9
A pin gives at most
5 mA · CE, PG, STAT1, STAT2 output sink current absolute max · p. 7
Feedback reference
1.536 V · feedback voltage, VFB_REG = 0x10, typical · p. 9
Junction to air (RRV)
29.4 K/W · junction-to-ambient thermal resistance · p. 8
Junction to case (RRV)
18.8 K/W · junction-to-case top thermal resistance · p. 8
Junction to board (RRV)
9.9 K/W · junction-to-board thermal resistance · p. 8
Switches at
250 kHz · typical, RFSW_SYNC = 133kΩ · p. 13
Switches at
500 kHz · typical, RFSW_SYNC = 50kΩ · p. 13

What it is and has

14
Input voltage range
4.2V to 36V · p. 1
Li-ion battery support
1 to 7 cells · p. 1
LiFePO4 battery support
1 to 9 cells · p. 1
External clock synchronization
Optional · p. 1
Loop compensation
Integrated, with soft start · p. 1
Charge voltage regulation accuracy
±0.5% · p. 1
Charge current regulation accuracy
±3% · p. 1
Input current regulation accuracy
±3% · p. 1
Protection
Battery overvoltage and overcurrent protection · p. 1
Protection
Charging safety timer · p. 1
Package
36-pin 6mm × 5mm QFN · p. 1
Battery voltage
up to 36V, multi-chemistry support · p. 1
Li-ion charge profile
1- to 7-cell · p. 1
LiFePO4 charge profile
1- to 9-cell · p. 1

Around it

28
res 10kΩ
between SCL and logic rail; I2C clock pull-up. · p. 4
res 10kΩ
between SDA and logic rail; I2C data pull-up. · p. 4
res 10kΩ
between INT and logic rail; Interrupt pull-up. · p. 4
res 10kΩ
between STAT1 and pull up rail; Charge status pull-up. · p. 4
res 10kΩ
between PG and pull up rail; Power good pull-up. · p. 4
cap 0.47-μF
between SRN and SRP; Ceramic differential-mode filter. · p. 5
cap 0.1-μF
between SRN and PGND; Optional ceramic common-mode filter. · p. 5
cap 0.1-μF
between SRP and PGND; Ceramic common-mode filter. · p. 5
cap 4.7μF
between DRV_SUP and PGND; Ceramic gate drive supply capacitor. · p. 5
cap 4.7μF
between REGN and PGND; Ceramic internal regulator output capacitor. · p. 5
cap 0.47μF
between ACN and ACP; Ceramic differential-mode filter. · p. 6
cap 0.1μF
between ACN and PGND; Optional ceramic common-mode filter. · p. 6
cap 0.1μF
between ACP and PGND; Ceramic common-mode filter. · p. 6
cap 1µF
between VAC and PGND; Input voltage detection and power capacitor. · p. 6
ind 2.2 to 15 µH
between SW1 and SW2; Recommended switched inductor range. · p. 8
res 5 mΩ
between SRP and SRN; Nominal battery current sense resistor. · p. 8
res 5 mΩ
between ACP and ACN; Nominal input current sense resistor; recommended range 0 to 10 mΩ. · p. 8
res 200 kΩ
between FSW_SYNC and PGND; Sets nominal switching frequency to 200 kHz; pin must not float. · p. 23
res 133 kΩ
between FSW_SYNC and PGND; Sets nominal switching frequency to 250 kHz; pin must not float. · p. 23
res 100 kΩ
between FSW_SYNC and PGND; Sets nominal switching frequency to 300 kHz; pin must not float. · p. 23
res 80 kΩ
between FSW_SYNC and PGND; Sets nominal switching frequency to 350 kHz; pin must not float. · p. 23
res 66.67 kΩ
between FSW_SYNC and PGND; Sets nominal switching frequency to 400 kHz; pin must not float. · p. 23
res 57.1 kΩ
between FSW_SYNC and PGND; Sets nominal switching frequency to 450 kHz; pin must not float. · p. 23
res 50 kΩ
between FSW_SYNC and PGND; Sets nominal switching frequency to 500 kHz; pin must not float. · p. 23
res 44.4 kΩ
between FSW_SYNC and PGND; Sets nominal switching frequency to 550 kHz; pin must not float. · p. 23
res 40 kΩ
between FSW_SYNC and PGND; Sets nominal switching frequency to 600 kHz; pin must not float. · p. 23
res 10kΩ
between ICHG and PGND; Example hardware setting for a 5A charge current limit. · p. 25
res 5kΩ
between ILIM_HIZ and PGND; Example hardware setting for a 10A input current limit with a 2mΩ RAC_SNS resistor. · p. 30

Specifications

170
ParameterConditionsAs printedPage
VoltageVAC, ACUV, ACOV, ACP, ACN, SRP, SRN, FB, FBGmin -0.3 · max 60 V7
VoltageSW1, SW2min -2 · max 60 V7
VoltageSW1, SW2 (40ns transient)min -4 · max 60 V7
VoltagePGmin -0.3 · max 40 V7
VoltageBTST1, HIDRV1 with respect to SW1min -0.3 · max 14 V7
VoltageBTST2, HIDRV2 with respect to SW2min -0.3 · max 14 V7
VoltageACP with respect to ACN, SRP with respect to SRNmin -0.3 · max 0.3 V7
VoltageCE, FSW_SYNC, ICHG, ILIM_HIZ, INT, REGN, SCL, SDA, MODE, STAT1, STAT2, TSmin -0.3 · max 6 V7
Output Sink CurrentCE, PG, STAT1, STAT2max 5 mA7
Junction temperature TJmin -40 · max 150 °C7
Storage temperature Tstgmin -65 · max 150 °C7
Electrostatic discharge V(ESD)Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins; ± ratingmax 2000 V7
Electrostatic discharge V(ESD)Charged device model (CDM), per ANSI/ESDA/JEDEC JS-002, all pins; ± ratingmax 500 V7
Input voltage VACmin 4.2 · max 36 V8
Battery voltage VBATmin 0 · max 36 V8
DRV_SUP pin direct drive voltage range VDRV_SUPmin 4 · max 12 V8
Switching Frequency FSWmin 200 · max 600 kHz8
Junction temperature TJmin -40 · max 125 °C8
Ambient temperature TAmin -40 · max 105 °C8
VAC capacitor CVACmin 1 uF8
Buck input capacitance (minimum value after derating) CINmin 80 uF8
Buck output capacitance (minimum value after derating) COUTmin 80 uF8
REGN capacitor (nominal value before derating) CREGNmin 4.7 uF8
DRV_SUP capacitor (nominal value before derating) CDRV_SUPmin 4.7 uF8
Switched Inductor Lmin 2.2 · max 15 uH8
Inductor DC resistance RDCRmin 1.75 · max 60 mΩ8
Input current sense resistor RAC_SNS0mΩ disables input current limit functionmin 0 · typ 5 · max 10 mΩ8
Battery current sense resistor RBAT_SNStyp 5 mΩ8
ICHG programming pulldown resistor RICHGPulled to GND disables hardware charge current limitmin 0 · max 100 kΩ8
ILIM_HIZ programming pulldown resistor RILIM_HIZPulled to GND disables hardware input current limitmin 0 · max 50 kΩ8
Junction-to-ambient thermal resistance (JEDEC(1)) RθJABQ25756E, RRV, 36 PINStyp 29.4 °C/W8
Junction-to-case (top) thermal resistance RθJC(top)BQ25756E, RRV, 36 PINStyp 18.8 °C/W8
Junction-to-board thermal resistance RθJBBQ25756E, RRV, 36 PINStyp 9.9 °C/W8
Junction-to-top characterization parameter ΨJTBQ25756E, RRV, 36 PINStyp 0.2 °C/W8
Junction-to-board characterization parameter ΨJBBQ25756E, RRV, 36 PINStyp 9.8 °C/W8
Junction-to-case (bottom) thermal resistance RθJC(bot)BQ25756E, RRV, 36 PINStyp 2.5 °C/W8
Quiescent battery current with BATFET on (ISRN + ISRP) IQ_BATVBAT = 28V, VAC = 0V, ADC_EN = 0, TJ < 105 °Ctyp 17 uA9
Quiescent battery current with BATFET on (ISRN + ISRP) IQ_BATVBAT = 28V, VAC = 0V, ADC_EN = 1, TJ < 105 °Ctyp 500 · max 700 uA9
Quiescent input current (IVAC) IQ_VACNot switchingtyp 0.75 · max 1 mA9
Quiescent battery current in Reverse mode (ISRN + ISRP) IQ_REVNot switchingtyp 0.75 · max 1 mA9
VAC operating range VVAC_OPmin 4.2 · max 70 V9
VAC operating range VVAC_OPmin 4.2 · max 36 V9
VAC converter enable threshold VVAC_OKVAC rising, no batterymin 4.2 V9
VAC converter disable threshold VVAC_OKZVAC falling, no batterymax 3.5 V9
ACUV comparator threshold to enter VAC_UVP VREF_ACUVVACUV fallingmin 1.095 · typ 1.1 · max 1.106 V9
ACUV comparator threshold hysteresis VREF_ACUV_HYSVACUV risingtyp 50 mV9
VAC internal threshold to enter VAC_OVP VVAC_INT_OVIN risingtyp 36 V9
VAC internal thresholds to exit VAC_OVP VVAC_INT_OVZIN fallingtyp 33 V9
ACOV comparator threshold to enter VAC_OVP VREF_ACOVVACOV risingmin 1.184 · typ 1.2 · max 1.206 V9
ACOV comparator threshold hysteresis VREF_ACOV_HYSVACOV fallingtyp 50 mV9
Feedback voltage range VVFB_RANGEmin 1.504 · max 1.566 V9
Typical feedback voltage step VVFB_STEPtyp 2 mV9
Nominal feedback voltage VVFB_NOMVFB_REG = 0x10typ 1.536 V9
Feedback voltage regulation accuracy VVFB_ACCTJ = 0°C to 85°Cmin -0.5 · max 0.5 %9
Feedback voltage regulation accuracy VVFB_ACCTJ = -40°C to 125°Cmin -0.7 · max 0.7 %9
FBG resistance to PGND RFBGIFBG = 1mAtyp 33 · max 55 Ω9
Charge current regulation range ICHG_REG_RANGEmin 0.4 · max 20 A9
Charge current regulation step ICHG_REG_STEPtyp 50 mA9
I2C setting charge current regulation accuracy ICHG_REG_ACCRBAT_SNS = 5mΩ, VBAT = 12V, 36V; ICHG_REG = 0x012C; 15 Amin -3 · max 3 %9
I2C setting charge current regulation accuracy ICHG_REG_ACCRBAT_SNS = 5mΩ, VBAT = 12V, 36V; ICHG_REG = 0x0064; 5 Amin -3 · max 3 %9
I2C setting charge current regulation accuracy ICHG_REG_ACCRBAT_SNS = 5mΩ, VBAT = 12V, 36V; ICHG_REG = 0x0028; 2 Amin -5 · max 5 %9
Hardware charge current limit set factor (Amperes of charge current per kΩ on ICHG pin) KICHGRBAT_SNS = 5mΩ, RICHG = 10kΩ, 5kΩ, and 3.33kΩmin 48 · typ 50 · max 52 Ax kΩ9
ICHG pin voltage when ICHG pin is in regulation VREF_ICHGtyp 2 V9
Trickle charge current accuracy for Li-Ion batteries IBAT_SHORTVFB < VBAT_SHORTtyp 150 mA10
Precharge current regulation range IPRECHG_RANGEVFB < VBAT_LOWV * VVFB_REGmin 0.25 · max 10 A10
Typical precharge SRP to SRN regulation voltage step IPRECHG_STEPVFB < VBAT_LOWV * VVFB_REGtyp 50 mA10
I2C setting precharge current accuracy IPRECHG_ACCRBAT_SNS = 5mΩ, VFB < VBAT_LOWV * VVFB_REG; IPRECHG = 0x003C; 3.0 Amin -4 · max 4 %10
I2C setting precharge current accuracy IPRECHG_ACCRBAT_SNS = 5mΩ, VFB < VBAT_LOWV * VVFB_REG; IPRECHG[1:0] = 0x0014; 1.0 Amin -10 · max 10 %10
I2C setting precharge current accuracy IPRECHG_ACCRBAT_SNS = 5mΩ, VFB < VBAT_LOWV * VVFB_REG; IPRECHG[1:0] = 0x000A; 0.50 Amin -30 · max 30 %10
Hardware precharge current limit set factor (Amperes of precharge current per kΩ on ICHG pin) KIPRECHGRBAT_SNS = 5mΩ, VFB < VBAT_LOWV * VVFB_REG, RICHG = 10kΩ, 5kΩ, and 3.33kΩmin 8.5 · typ 10 · max 10.5 Ax kΩ10
ICHG pin voltage when IPRECHG is in regulation VREF_IPRECHGVFB < VBAT_LOWV * VVFB_REGmin 388 · typ 400 · max 412 mV10
Termination current range ITERM_RANGEVFB = VVFB_REGmin 0.25 · max 10 A10
Typical termination SRP to SRN voltage step ITERM_STEPVFB = VVFB_REGtyp 50 mA10
Termination current accuracy ITERM_ACCRBAT_SNS = 5mΩ, VBAT = 12V, 36V; ITERM = 0x001E; 1.5 Amin -7 · max 7 %10
Termination current accuracy ITERM_ACCRBAT_SNS = 5mΩ, VBAT = 12V, 36V; ITERM = 0x000A; 0.50 Amin -20 · max 20 %10
Termination current accuracy ITERM_ACCRBAT_SNS = 5mΩ, VBAT = 12V, 36V; ITERM = 0x0005; 0.250 Amin -50 · max 50 %10
Hardware termination current limit set factor (Amperes of termination current per kΩ on ICHG pin) KITERMRBAT_SNS = 5mΩ, VFB = VVFB_REG, RICHG = 10kΩ, 5kΩ, and 3.33kΩmin 3.5 · typ 5 · max 5.5 Ax kΩ10
ICHG pin voltage when ITERM is detected via ICHG pin VREF_ITERMVBAT = 12V, 36Vmin 188 · typ 200 · max 212 mV10
Trickle charge to pre-charge transition VBAT_SHORTVSRN risingmin 2.8 · typ 3 · max 3.2 V10
Pre-charge to trickle charge transition VBAT_SHORTVSRN fallingmin 2.2 · typ 2.4 · max 2.6 V10
Pre-charge to fast-charge transition VBAT_LOWVVFB rising, as percentage of VFB_REG, VBAT_LOWV[2:0] = 3min 69 · typ 71.7 · max 73.8 %10
Pre-charge to fast-charge transition VBAT_LOWVVFB rising, as percentage of VFB_REG, VBAT_LOWV[2:0] = 2min 64.3 · typ 66.7 · max 69 %10
Pre-charge to fast-charge transition VBAT_LOWVVFB rising, as percentage of VFB_REG, VBAT_LOWV[2:0] = 1min 52 · typ 55 · max 58 %10
Pre-charge to fast-charge transition VBAT_LOWVVFB rising, as percentage of VFB_REG, VBAT_LOWV[2:0] = 0min 27 · typ 30 · max 33 %10
BAT_LOWV hysteresis VBAT_LOWV_HYStyp 5 %10
Battery recharge threshold for Li-Ion and LiFePO4 VRECHGVFB falling, as percentage of VFB_REG, VRECHG[1:0] = 3typ 97.6 %11
Battery recharge threshold for Li-Ion and LiFePO4 VRECHGVFB falling, as percentage of VFB_REG, VRECHG[1:0] = 2typ 95.2 %11
Battery recharge threshold for Li-Ion and LiFePO4 VRECHGVFB falling, as percentage of VFB_REG, VRECHG[1:0] = 1typ 94.3 %11
Battery recharge threshold for Li-Ion and LiFePO4 VRECHGVFB falling, as percentage of VFB_REG, VRECHG[1:0] = 0typ 93 %11
I2C setting input current regulation accuracy in forward mode IIREG_DPM_ACCRAC_SNS = 2mΩ, IAC_DPM = 0x00A0; regulation currenttyp 20 A11
I2C setting input current regulation accuracy in forward mode IIREG_DPM_ACCRAC_SNS = 2mΩ, IAC_DPM = 0x00A0min -3 · max 3 %11
I2C setting input current regulation accuracy in forward mode IIREG_DPM_ACCRAC_SNS = 2mΩ, IAC_DPM = 0x0050; regulation currenttyp 10 A11
I2C setting input current regulation accuracy in forward mode IIREG_DPM_ACCRAC_SNS = 2mΩ, IAC_DPM = 0x0050min -4 · max 4 %11
I2C setting input current regulation accuracy in forward mode IIREG_DPM_ACCRAC_SNS = 2mΩ, IAC_DPM = 0x0028; regulation currenttyp 5 A11
I2C setting input current regulation accuracy in forward mode IIREG_DPM_ACCRAC_SNS = 2mΩ, IAC_DPM = 0x0028min -7 · max 7 %11
Hardware input current limit set factor (Amperes of input current per kΩ on ILIM_HIZ pin) KILIMRAC_SNS = 2mΩ, RILIM = 5kΩ, 2.5kΩ, and 1.67kΩmin 48 · typ 50 · max 52 Ax kΩ11
ILIM_HIZ pin voltage when ILIM_HIZ pin is in regulation VREF_ILIM_HIZtyp 2 V11
ILIM_HIZ input high threshold to enter HIZ mode VIH_ILIM_HIZVILIM_HIZ risingmin 3.7 V11
Input voltage DPM regulation range VVREG_DPM_RANGEmin 4.2 · max 36 V11
I2C setting input voltage regulation accuracy in forward mode VVREG_DPM_ACCVAC_DPM = 0x04E2; regulation voltagetyp 25 V11
I2C setting input voltage regulation accuracy in forward mode VVREG_DPM_ACCVAC_DPM = 0x04E2min -2 · max 2 %11
I2C setting input voltage regulation accuracy in forward mode VVREG_DPM_ACCVAC_DPM = 0x03B6; regulation voltagetyp 19 V11
I2C setting input voltage regulation accuracy in forward mode VVREG_DPM_ACCVAC_DPM = 0x03B6min -2 · max 2 %11
ACUV pin voltage when in VDPM regulation VACUV_DPMmin 1.198 · typ 1.21 · max 1.222 V11
VAC Voltage regulation range in Reverse mode VREV_RANGEmin 3.3 · max 36 V11
VAC Voltage regulation accuracy in Reverse mode VREV_ACCVAC_REV = 0x02EE; regulation voltagetyp 15 V11
VAC Voltage regulation accuracy in Reverse mode VREV_ACCVAC_REV = 0x02EEmin -2 · max 2 %11
VAC Voltage regulation accuracy in Reverse mode VREV_ACCVAC_REV = 0x00FA; regulation voltagetyp 5 V11
VAC Voltage regulation accuracy in Reverse mode VREV_ACCVAC_REV = 0x00FAmin -2 · max 2 %11
Input current regulation accuracy in Reverse mode IIREV_ACCRAC_SNS = 2mΩ, IAC_REV = 0x00A0; regulation currenttyp 20 A11
Input current regulation accuracy in Reverse mode IIREV_ACCRAC_SNS = 2mΩ, IAC_REV = 0x00A0min -3.5 · max 3.5 %11
Input current regulation accuracy in Reverse mode IIREV_ACCRAC_SNS = 2mΩ, IAC_REV = 0x0028; regulation currenttyp 5 A11
Input current regulation accuracy in Reverse mode IIREV_ACCRAC_SNS = 2mΩ, IAC_REV = 0x0028min -5.5 · max 5.5 %11
TS pin voltage rising T1 threshold, charge suspended above this voltage. VT1_RISEAs Percentage to REGN, TS_T1=0°C w/ 103ATmin 72.75 · typ 73.25 · max 73.85 %11
TS pin voltage rising THOT threshold. Reverse mode allowed above this voltage VBHOT_RISEAs Percentage to REGN, (BHOT = 60°C w/ 103AT)min 35 · typ 35.5 · max 36 %13
TS pin voltage rising THOT threshold. Reverse mode allowed above this voltage VBHOT_RISEAs Percentage to REGN, (BHOT 65°C w/ 103AT)min 32 · typ 32.5 · max 33 %13
Battery overvoltage threshold VBAT_OVVFB rising, as percentage of VFB_REGmin 102.5 · typ 104 · max 105.5 %13
Battery overvoltage falling threshold VBAT_OVZVFB falling, as percentage of VFB_REGmin 100.5 · typ 102 · max 103.5 %13
Battery charge over-current threshold VICHG_OCVSRP - VSRN risingmin 120 · max 170 mV13
Thermal shutdown rising threshold TSHUTTemperature increasingtyp 150 °C13
Thermal shutdown falling threshold TSHUTTemperature decreasingtyp 135 °C13
REGN LDO output voltage VREGNIREGN = 20mAmin 4.8 · typ 5 · max 5.2 V13
REGN LDO output voltage VREGNVAC = 5V, IREGN = 20mAmin 4.35 · typ 4.6 V13
REGN LDO current limit IREGNVREGN = 4.5Vmin 70 mA13
REGN OK threshold to allow switching VREGN_OKREGN risingtyp 3.55 V13
DRV_SUP under-voltage threshold to allow switching VDRV_UVPZDRV_SUP risingmax 3.7 V13
DRV_SUP over-voltage threshold to disable switching VDRV_OVPDRV_SUP risingmin 12.8 · typ 13.2 · max 13.6 V13
VAC discharge load current IAC_LOADmin 16 mA13
Battery (SRP) discharge load current IBAT_LOADmin 16 mA13
Switching Frequency fSWRFSW_SYNC = 133kΩmin 212 · typ 250 · max 288 kHz13
Switching Frequency fSWRFSW_SYNC = 50kΩmin 425 · typ 500 · max 575 kHz13
FSW_SYNC input high threshold VIH_SYNCmin 1.3 V13
FSW_SYNC input low threshold VIL_SYNCmax 0.4 V13
FSW_SYNC input pulse width PWSYNCmin 80 ns13
Buck side high-side turnon resistance RHIDRV1_ONVBTST1 - VSW1 = 5Vtyp 3.4 Ω13
Buck side high-side turnoff resistance RHIDRV1_OFFVBTST1 - VSW1 = 5Vtyp 1 Ω13
Bootstrap refresh comparator threshold voltage VBTST1_REFRESHBTST1 falling, VBTST1 - VSW1 when low-side refresh pulse is requestedmin 2.7 · typ 3.1 · max 3.9 V13
Buck side low-side turnon resistance RLODRV1_ONVREGN = 5Vtyp 3.4 Ω13
Buck side low-side turnoff resistance RLODRV1_OFFVREGN = 5Vtyp 1 Ω13
Buck side dead time, both edges tDT1typ 45 ns13
Boost side high-side turnon resistance RHIDRV2_ONVBTST2 - VSW2 = 5Vtyp 3.4 Ω13
Boost side high-side turnoff resistance RHIDRV2_OFFVBTST2 - VSW2 = 5Vtyp 1 Ω14
Bootstrap refresh comparator threshold voltage VBTST2_REFRESHBTST2 falling, VBTST2 - VSW2 when low-side refresh pulse is requestedmin 2.7 · typ 3.1 · max 3.9 V14
Boost side low-side turnon resistance RLODRV2_ONVREGN = 5Vtyp 3.4 Ω14
Boost side low-side turnoff resistance RLODRV2_OFFVREGN = 5Vtyp 1 Ω14
Boost side dead time, both edges tDT2typ 45 ns14
Conversion-time, each measurement tADC_CONVADC_SAMPLE[1:0] = 00typ 24 ms14
Conversion-time, each measurement tADC_CONVADC_SAMPLE[1:0] = 01typ 12 ms14
Conversion-time, each measurement tADC_CONVADC_SAMPLE[1:0] = 10typ 6 ms14
Effective resolution ADCRESADC_SAMPLE[1:0] = 00min 14 · typ 15 bits14
Effective resolution ADCRESADC_SAMPLE[1:0] = 01min 13 · typ 14 bits14
Effective resolution ADCRESADC_SAMPLE[1:0] = 10min 12 · typ 13 bits14
Input current ADC reading (positive or negative) IAC_ADCRange with 2mΩ RAC_SNSmin -50000 · max 50000 mA14
Input current ADC reading (positive or negative) IAC_ADCLSB with 2mΩ RAC_SNStyp 2 mA14
Input voltage ADC reading VAC_ADCRangemin 0 · max 36000 mV14
Input voltage ADC reading VAC_ADCLSBtyp 2 mV14
Battery voltage ADC reading VBAT_ADCRangemin 0 · max 36000 mV14
Battery voltage ADC reading VBAT_ADCLSBtyp 2 mV14
TS voltage ADC reading, as percentage of REGN TSADCRangemin 0 · max 99.9 %14
TS voltage ADC reading, as percentage of REGN TSADCLSBtyp 0.098 %14
FB voltage ADC reading VFB_ADCRangemin 0 · max 2047 mV14
FB voltage ADC reading VFB_ADCLSBtyp 1 mV14
Input high threshold level VIHI2C INTERFACE (SCL, SDA)min 1.3 V14
Input low threshold level VILI2C INTERFACE (SCL, SDA)max 0.4 V14
Output low threshold level VOLI2C INTERFACE (SCL, SDA); Sink current = 5mAmax 0.4 V14
High-level leakage current IIN_BIASI2C INTERFACE (SCL, SDA); Pull up rail 3.3Vmax 1 uA14
Input high threshold level (CE) VIHLOGIC I/O PIN (CE, PG, STAT1, STAT2)min 1.3 V14
Output low threshold level (CE, PG, STAT1, STAT2) VOLSink current = 5mAmax 0.4 V14
Input low threshold level (CE) VILmax 0.4 V14
High-level leakage current (CE, PG, STAT1, STAT2) IOUT_BIASPull up rail 3.3Vmax 1 uA14

Pins, by the datasheet

37
1 SCL
I2C clock; connect to the logic rail through a 10kΩ resistor. · p. 4
2 SDA
I2C data; connect to the logic rail through a 10kΩ resistor. · p. 4
3 INT
Interrupt output; pull up through 10kΩ; sends an active low 256us status or fault pulse. · p. 4
4 STAT1
Charge status output; pull up through 10kΩ; can serve as a general purpose indicator when its status function is disabled. · p. 4
5 STAT2
Charge status output; pull up through 10kΩ; can serve as a general purpose indicator when its status function is disabled. · p. 4
6 PG
Active low power good indicator; pull up through 10kΩ; indicates an input within the ACUV/ACOV window. · p. 4
7 CE
Active low charge enable; drive high or low; can serve as a general purpose indicator when its enable function is disabled. · p. 4
8 TS
Temperature qualification input; connect an NTC thermistor and a divider from REGN to PGND; out-of-range voltage suspends charging. · p. 5
9 ICHG
Charge current limit programming and monitoring; connect a programming resistor to PGND, or pull to PGND when unused. · p. 5
10 ILIM_HIZ
Input current limit programming and monitoring; high forces HIZ mode; connect a programming resistor to PGND, or pull to PGND when unused. · p. 5
11 FBG
Battery feedback divider return; driven to PGND while charging and high impedance outside the input operating window. · p. 5
12 FB
Battery regulation voltage feedback input from a resistive divider across the battery terminals. · p. 5
13 SRN
Negative charge current sense input; filter to SRP with 0.47-uF ceramic and optionally to PGND with 0.1-uF ceramic. · p. 5
14 SRP
Positive charge current sense input; filter to SRN with 0.47-uF ceramic and to PGND with 0.1-uF ceramic. · p. 5
15 NC
Leave floating; do not tie to PGND. · p. 5
16 NC
Leave floating; do not tie to PGND. · p. 5
17 PGND
Tie directly to PGND pin 22. · p. 5
18 SW2
Boost half bridge switching node; connects the boost high-side source, low-side drain, and inductor to SW1. · p. 5
19 HIDRV2
Boost high-side N-channel MOSFET gate driver. · p. 5
20 BTST2
Boost high-side gate driver supply; connect a capacitor to SW2. · p. 5
21 LODRV2
Boost low-side N-channel MOSFET gate driver. · p. 5
22 PGND
Power ground return for the low-side gate drivers. · p. 5
23 DRV_SUP
Gate drive supply; connect 4.7uF ceramic to power ground; use REGN or an external supply up to 12V. · p. 5
24 REGN
Internal linear regulator output; connect 4.7uF ceramic to power ground; may supply DRV_SUP. · p. 5
25 LODRV1
Buck low-side N-channel MOSFET gate driver. · p. 5
26 BTST1
Buck high-side gate driver supply; connect a capacitor to SW1. · p. 5
27 HIDRV1
Buck high-side N-channel MOSFET gate driver. · p. 5
28 SW1
Buck half bridge switching node; connects the buck high-side source, low-side drain, and inductor to SW2. · p. 6
29 ACN
Negative adapter current sense input; filter to ACP with 0.47uF ceramic and optionally to PGND with 0.1uF ceramic. · p. 6
30 ACP
Positive adapter current sense input; filter to ACN with 0.47uF ceramic and to PGND with 0.1uF ceramic. · p. 6
31 NC
Leave floating; do not tie to PGND. · p. 6
32 VAC
Input voltage detection; connect 1uF to PGND; regulated to VAC_REV in reverse mode. · p. 6
33 VAC
Input bias power for the IC; connect 1uF to PGND and reference the ACOV/ACUV dividers to this pin. · p. 6
34 ACUV
Input undervoltage comparator and voltage regulation programming input; connect a VAC-to-PGND divider, or pull to VAC when unused. · p. 6
35 ACOV
Input overvoltage comparator input; connect a VAC-to-PGND divider, or pull to PGND when unused. · p. 6
36 FSW_SYNC
Switching frequency programming resistor connection to PGND or external 200kHz to 600kHz synchronization clock input. · p. 6
37 Thermal Pad
Solder to the board with vias star-connecting the pad plane to PGND and the ground plane for heat dissipation. · p. 6

Open-source boards using it

4
  • 4 layers100 × 70 mmElonMux, the printed circuit board in 3D

    ElonMux

    EPFLXplore/Power_HW

    KiCad design files for the power boards of the Xplore rover.

    329 parts7
  • 4 layers160 × 80 mmBattGuard, the printed circuit board in 3D

    BattGuard

    Fluffster65/BattGuard

    Team 23 Senior Design project; description in progress...

    179 parts
  • 2 layers95.9 × 90.2 mmChargeController3.0, the printed circuit board in 3D

    ChargeController3.0

    UWCubeSat/BMS-EPS-HS2

    Repository of the HS-2 Battery Management System

    96 parts
  • 2 layers90.2 × 95.9 mmChargeController2.0, the printed circuit board in 3D

    ChargeController2.0

    UWCubeSat/BMS-EPS-HS2

    Repository of the HS-2 Battery Management System

    88 parts

Questions

Is there a KiCad symbol and footprint for the BQ25756ERRVR?

Yes. The symbol is BQ25756E:BQ25756E and the footprint qfn-36-1ep-5x6mm-p0-5mm-ep3-6x4-6mm:QFN-36-1EP_5x6mm_P0.5mm_EP3.6x4.6mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the BQ25756ERRVR?

VQFN-36-EP(6x5), with 37 pins. Its footprint is drawn on this page.

Where is the BQ25756ERRVR datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the BQ25756ERRVR?

JLCPCB lists it as part C22427194, with 101 in stock; the sellers' links on this page open their listings.

Which open-source boards use the BQ25756ERRVR?

4 boards in 3 repositories on GitHub; the most starred are listed on this page, with their KiCad files.