
BQ25619RTW
Texas InstrumentsExtended
-40℃~+85℃ 1 1.5A 4.52V 4V~13.5V 9.5uA Charging IC I2C Lithium Battery Support Support WQFN-24-EP(4x4) Battery Management ROHS
- Part id
- ti/BQ25619RTW
- Category
- Battery Management
- Package
- WQFN-24-EP(4x4)
- Pins
- 25
- In stock
- 2,663 at JLCPCB (C2864534)
- Used on
- 4 open-source boards
Overview
The BQ25619RTW is a battery Management made by Texas Instruments in a WQFN-24-EP(4x4) package with 25 pins. -40℃~+85℃ 1 1.5A 4.52V 4V~13.5V 9.5uA Charging IC I2C Lithium Battery Support Support WQFN-24-EP(4x4) Battery Management ROHS.
PCBKit's library has its KiCad symbol (EasyEDA_Cloud:BQ25619RTWT, from EasyEDA) and its footprint (EasyEDA_Cloud:WQFN-24_L4.0-W4.0-P0.50-TL-EP2.7, from EasyEDA), ready for a KiCad board. 2,663 are in stock at JLCPCB (part C2864534). 4 open-source boards in 4 repositories on GitHub use it.
Symbol
Footprint
From the datasheet
14- Supply, least
- 4 V · VBUS, recommended operating min · p. 7
- Supply, most
- 13.5 V · VBUS, recommended operating max · p. 7
- Supply, absolute maximum
- 22 V · VBUS, converter not switching, absolute max · p. 7
- Works from
- -40 °C · Ambient temperature min · p. 7
- Works up to
- 85 °C · Ambient temperature max · p. 7
- Junction, hottest
- 150 °C · Junction temperature absolute max · p. 7
- Takes working
- 2.3 mA · VBUS, buck converter switching, charge disabled, ISYS = 0A, typical · p. 8
- Takes asleep
- 7 µA · Battery Ship mode, BATFET disabled, typical · p. 8
- Gives
- 1.5 A · Fast charging current max · p. 7
- A pin gives at most
- 6 mA · SDA, STAT, INT, PMID_GOOD output sink absolute max · p. 7
- Junction to air (RTW (WQFN))
- 35.6 K/W · Junction-to-ambient thermal resistance · p. 8
- Junction to board (RTW (WQFN))
- 11.9 K/W · Junction-to-board thermal resistance · p. 8
- Junction to case (RTW (WQFN))
- 22.7 K/W · Junction-to-case top thermal resistance · p. 8
- Switches at
- 1.5 MHz · typical PWM oscillator frequency · p. 12
What it is and has
9- Charge current
- 1.5A · p. 3
- Battery chemistry
- Li-ion and Li-polymer · p. 3
- Boost output
- 5V; adjustable 4.6V/4.75V/5V/5.15V · p. 3
- Interface
- I2C · p. 3
- Package
- 24-pin, 4mm × 4mm x 0.75mm WQFN · p. 3
- Safety certification
- IEC 62368-1 CB · p. 1
- Thermal regulation
- Reduces charge current above 110°C junction temperature · p. 3
- Charge voltage regulation accuracy
- ±0.5%, 10mV step · p. 1
- Safety certification
- IEC 62368-1 CB Certification · p. 1
Around it
12- cap 0.047-μF
- between SW and BTST; Bootstrap capacitor. · p. 5
- cap 4.7-μF
- between REGN and GND; 10-V rating, ceramic, close to the IC; analog GND. · p. 5
- cap 1 µF
- between VBUS and GND; Recommended nominal VBUS capacitance. · p. 7
- cap 10 µF
- between PMID and GND; Recommended nominal PMID capacitance. · p. 7
- cap 10 µF
- between SYS and GND; Place close to SYS; pin description specifies 10 uF minimum. · p. 7
- cap 10 µF
- between BAT and GND; Place close to BAT. · p. 7
- res 10-kΩ
- between INT and logic rail; Interrupt pull-up. · p. 5
- res 10-kΩ
- between PMID_GOOD and REGN; Pull-up. · p. 5
- res 10-kΩ
- between SCL and logic rail; I2C clock pull-up. · p. 5
- res 10-kΩ
- between SDA and logic rail; I2C data pull-up. · p. 5
- res 10-kΩ
- between STAT and logic rail; Status pull-up. · p. 5
- res 10-kΩ
- between REGN and TS; When TS is unused; alternatively set TS_IGNORE HIGH. · p. 5
Specifications
176| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Voltage | VAC (converter not switching) | min -2 · max 22 V | 7 |
| Voltage | VBUS (converter not switching) | min -2 · max 22 V | 7 |
| Voltage | PMID (converter not switching) | min -0.3 · max 22 V | 7 |
| Voltage | SW | min -0.3 · max 16 V | 7 |
| Voltage | BAT, SYS (converter not switching) | min -0.3 · max 7 V | 7 |
| Voltage | BTST | min -0.3 · max 22 V | 7 |
| Voltage | BATSNS (converter not switching) | min -0.3 · max 7 V | 7 |
| Voltage | PSEL, STAT, SCL, SDA, INT, PMID_GOOD, CE, TS, QON | min -0.3 · max 7 V | 7 |
| Output Sink Current | SDA, STAT, INT, PMID_GOOD | max 6 mA | 7 |
| Junction temperature TJ | min -40 · max 150 °C | 7 | |
| Storage temperature Tstg | min -55 · max 150 °C | 7 | |
| Electrostatic discharge V(ESD) | Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins | min -2000 · max 2000 V | 7 |
| Electrostatic discharge V(ESD) | Charged device model (CDM), per JEDEC specification JESD22-C101, all pins | min -250 · max 250 V | 7 |
| Input voltage VVBUS | min 4 · max 13.5 V | 7 | |
| Battery voltage VBAT | max 4.52 V | 7 | |
| Input current IVBUS | max 3.2 A | 7 | |
| Output current (SW) ISW | max 1.8 A | 7 | |
| Fast charging current IBAT | max 1.5 A | 7 | |
| RMS discharge current IBAT | max 5 A | 7 | |
| Ambient temperature TA | min -40 · max 85 °C | 7 | |
| Inductance L | typ 1 · max 2.2 uH | 7 | |
| VBUS capacitance CVBUS | typ 1 uF | 7 | |
| PMID capacitance CPMID | typ 10 uF | 7 | |
| SYS capacitance CSYS | typ 10 uF | 7 | |
| BAT capacitance CBAT | typ 10 uF | 7 | |
| REGN capacitance CREGN | typ 4.7 uF | 7 | |
| Junction-to-ambient thermal resistance (JEDEC(1)) RθJA | BQ25619, RTW (WQFN), 24 Pins | typ 35.6 °C/W | 8 |
| Junction-to-case (top) thermal resistance RθJC(top) | BQ25619, RTW (WQFN), 24 Pins | typ 22.7 °C/W | 8 |
| Junction-to-board thermal resistance RθJB | BQ25619, RTW (WQFN), 24 Pins | typ 11.9 °C/W | 8 |
| Junction-to-top characterization parameter ΨJT | BQ25619, RTW (WQFN), 24 Pins | typ 0.2 °C/W | 8 |
| Junction-to-board characterization parameter ΨJB | BQ25619, RTW (WQFN), 24 Pins | typ 12 °C/W | 8 |
| Junction-to-case (bottom) thermal resistance RθJC(bot) | BQ25619, RTW (WQFN), 24 Pins | typ 2.6 °C/W | 8 |
| Quiescent battery current (BATSNS, BAT, SYS, SW) IQ_BAT | VBAT = 4.5V, VBUS floating, SCL, SDA = 0V or 1.8V, TJ < 85 °C, BATFET enabled | typ 9.5 · max 15 uA | 8 |
| Shipmode battery current (BATSNS, BAT, SYS, SW) ISHIP_BAT | VBAT = 4.5V, VBUS floating, SCL, SDA = 0V or 1.8V, TJ < 85 °C, BATFET disabled | typ 7 · max 9.5 uA | 8 |
| Input current (VBUS) in buck mode when converter is switching IVBUS | VBUS=5V, charge disabled, converter switching, ISYS = 0A | typ 2.3 mA | 8 |
| Quiescent input current in HIZ IHIZ_VBUS | VAC/VBUS = 5V, HIZ mode, no battery | typ 37 · max 50 uA | 8 |
| Quiescent input current in HIZ IHIZ_VBUS | VAC/VBUS = 12V, HIZ mode, no battery | typ 68 · max 90 uA | 8 |
| Quiescent battery current (BATSNS, BAT, SYS, SW) in boost mode when converter is switching IBST | VBAT = 4.5V, VBUS = 5V, boost mode enabled, converter switching, IPMID = 0A | typ 2.4 mA | 8 |
| VBUS operating range VVBUS_OP | min 4 · max 13.5 V | 8 | |
| VBUS rising for active I2C, no battery VVBUS_UVLOZ | VBUS rising | typ 3.3 · max 3.7 V | 8 |
| VBUS falling to turnoff I2C, no battery VVBUS_UVLO | VBUS falling | typ 3 · max 3.3 V | 8 |
| VBUS to enable REGN VVBUS_PRESENT | VBUS rising | typ 3.65 · max 3.9 V | 8 |
| VBUS to disable REGN VVBUS_PRESENTZ | VBUS falling | typ 3.15 · max 3.4 V | 9 |
| Enter Sleep mode threshold VSLEEP | VBUS falling, VBUS - VBAT, VBAT = 4V | min 15 · typ 60 · max 110 mV | 9 |
| Exit Sleep mode threshold VSLEEPZ | VBUS rising, VBUS - VBAT, VBAT = 4V | min 115 · typ 220 · max 340 mV | 9 |
| VAC overvoltage rising threshold to turn of switching VACOV | VAC rising, OVP[1:0]=00 | min 5.45 · typ 5.85 · max 6.07 V | 9 |
| VAC overvoltage rising threshold to turn of switching VACOV | VAC rising, OVP[1:0]=01 | min 6.1 · typ 6.4 · max 6.75 V | 9 |
| VAC overvoltage rising threshold to turn of switching VACOV | VAC rising, OVP[1:0]=10 | min 10.45 · typ 11 · max 11.55 V | 9 |
| VAC overvoltage rising threshold to turn of switching VACOV | VAC rising, OVP[1:0]=11 (default) | min 13.5 · typ 14.2 · max 14.85 V | 9 |
| VAC overvoltage falling threshold to resume switching VACOV | VAC falling, OVP[1:0]=00 | min 5.2 · typ 5.6 · max 5.8 V | 9 |
| VAC overvoltage falling threshold to resume switching VACOV | VAC falling, OVP[1:0]=01 | min 5.8 · typ 6.2 · max 6.45 V | 9 |
| VAC overvoltage falling threshold to resume switching VACOV | VAC falling, OVP[1:0]=10 | min 10 · typ 10.7 · max 11.1 V | 9 |
| VAC overvoltage falling threshold to resume switching VACOV | VAC falling, OVP[1:0]=11 (default) | min 13 · typ 13.9 · max 14.5 V | 9 |
| BAT voltage for active I2C, no VBUS VBAT_UVLOZ | VBAT rising | min 2.5 V | 9 |
| BAT depletion rising threshold to turn on BATFET VBAT_DPLZ | VBAT rising | min 2.35 · max 2.8 V | 9 |
| BAT depletion falling threshold to turn off BATFET VBAT_DPL | VBAT falling | min 2.18 · max 2.62 V | 9 |
| Bad adapter detection threshold VPOORSRC | VBUS falling | min 3.75 · typ 3.9 · max 4 V | 9 |
| Typical minimum system regulation voltage VSYS_MIN | VBAT=3.2V < SYS_MIN = 3.5V, ISYS = 0A | min 3.5 · typ 3.65 V | 9 |
| System overvoltage threshold VSYS_OVP | VREG = 4.35V, Charge disabled, ISYS = 0A | typ 4.7 V | 9 |
| Blocking FET on-resistance (BQ25619) RON_RBFET | BQ25619 | typ 45 mΩ | 9 |
| High-side switching FET on-resistance (BQ25619) RON_HSFET | BQ25619 | typ 62 mΩ | 9 |
| Low-side switching FET on-resistance (BQ25619) RON_LSFET | BQ25619 | typ 71 mΩ | 9 |
| BATFET forward voltage in supplement mode VBATFET_FWD | BAT discharge current 10mA, converter running | typ 30 mV | 9 |
| Typical charge voltage regulation range VREG_RANGE | min 3.5 · max 4.52 V | 9 | |
| Typical charge voltage step VREG_STEP | 4.3V < VREG < 4.52V | typ 10 mV | 9 |
| Charge voltage accuracy VREG_ACC | VREG = 4.2V, TJ = –40°C - 85°C | min 4.183 · typ 4.2 · max 4.2168 V | 9 |
| Charge voltage accuracy VREG_ACC | VREG = 4.35V, TJ = –40°C - 85°C | min 4.333 · typ 4.35 · max 4.367 V | 9 |
| Charge voltage accuracy VREG_ACC | VREG = 4.45V, TJ = –40°C - 85°C | min 4.432 · typ 4.45 · max 4.468 V | 9 |
| Typical charge current regulation range ICHG_RANGE | min 0 · max 1.5 A | 9 | |
| Typical charge current regulation step ICHG_STEP | typ 20 mA | 9 | |
| Fast charge current regulation accuracy ICHG_ACC | ICHG = 0.24A, VBAT = 3.1V or 3.8V, TJ = –40°C - 85°C | min 0.216 · typ 0.24 · max 0.264 A | 10 |
| Fast charge current regulation accuracy ICHG_ACC | ICHG = 0.72A, VBAT = 3.1V or 3.8V, TJ = –40°C - 85°C | min 0.684 · typ 0.72 · max 0.756 A | 10 |
| Fast charge current regulation accuracy ICHG_ACC | ICHG = 1.50A, VBAT = 3.1V or 3.8V, TJ = –40°C - 85°C | min 1.425 · typ 1.5 · max 1.575 A | 10 |
| Typical pre-charge current range IPRECHG_RANGE | min 20 · max 260 mA | 10 | |
| Typical pre-charge current step IPRECHG_STEP | typ 20 mA | 10 | |
| Precharge current accuracy IPRECHG_ACC | VBAT = 2.6V, IPRECHG = 40mA | min 28 · typ 40 · max 52 mA | 10 |
| Precharge current accuracy IPRECHG_ACC | VBAT = 2.6V, IPRECHG = 120mA | min 84 · typ 120 · max 156 mA | 10 |
| Typical termination current range ITERM_RANGE | min 20 · max 260 mA | 10 | |
| Typical termination current step ITERM_STEP | typ 20 mA | 10 | |
| Termination current accuracy ITERM_ACC | ITERM=40mA, ICHG>260mA, VREG=4.35V, TJ = 0°C - 85°C | min 30 · typ 40 · max 50 mA | 10 |
| Termination current accuracy ITERM_ACC | ITERM=20mA, ICHG<260mA, VREG=4.35V, TJ = 0°C - 85°C | min 10 · typ 20 · max 30 mA | 10 |
| Battery short voltage rising threshold to start pre-charge VBAT_SHORTZ | VBAT rising | min 2.13 · typ 2.25 · max 2.35 V | 10 |
| Battery short voltage falling threshold to stop pre-charge VBAT_SHORT | VBAT falling | min 1.85 · typ 2 · max 2.15 V | 10 |
| Battery short trickle charging current IBAT_SHORT | VBAT < VBAT_SHORTZ | min 15 · typ 25 · max 30 mA | 10 |
| Battery LOWV rising threshold to start fast-charge VBATLOWV | VBAT rising | min 3 · typ 3.12 · max 3.24 V | 10 |
| Battery LOWV falling threshold to stop fast-charge VBATLOWV | VBAT falling | min 2.7 · typ 2.8 · max 2.9 V | 10 |
| Battery recharge threshold VRECHG | VRECHG=0, VBAT falling (default) | min 90 · typ 120 · max 150 mV | 10 |
| Battery recharge threshold VRECHG | VRECHG=1, VBAT falling | min 185 · typ 210 · max 245 mV | 10 |
| System discharge load current during SYSOVP ISYS_LOAD | typ 30 mA | 10 | |
| Battery FET on-resistance RON_BATFET | TJ = -40°C - 85°C | typ 19.5 · max 26 mΩ | 10 |
| Battery FET on-resistance RON_BATFET | TJ = -40°C - 125°C | typ 19.5 · max 30 mΩ | 10 |
| Battery overvoltage rising threshold VBAT_OVP | VBAT rising, as percentage of VREG | min 103 · typ 104 · max 105 % | 10 |
| Battery overvoltage falling threshold VBAT_OVP | VBAT falling, as percentage of VREG | min 101 · typ 102 · max 103 % | 10 |
| Typical input voltage regulation range VINDPM_RANGE | min 3.9 · max 5.4 V | 10 | |
| Typical input voltage regulation step VINDPM_STEP | typ 100 mV | 10 | |
| Typical input voltage regulation accuracy VINDPM_ACC | min 4.365 · typ 4.5 · max 4.635 V | 10 | |
| VINDPM threshold to track battery voltage VINDPM_TRACK | VBAT = 4.35V, VINDPM_BAT_TRACK = VBAT+200mV | min 4.45 · typ 4.55 · max 4.74 V | 10 |
| Typical input current regulation range IINDPM_RANGE | min 0.1 · max 3.2 A | 10 | |
| Typical input current regulation step IINDPM_STEP | typ 100 mA | 10 | |
| Input current regulation accuracy IINDPM_ACC | IINDPM = 500mA (TJ=-40°C - 85°C) | min 450 · typ 465 · max 500 mA | 10 |
| Input current regulation accuracy IINDPM_ACC | IINDPM = 900mA (TJ=-40°C-85°C) | min 750 · typ 835 · max 900 mA | 10 |
| Input current regulation accuracy IINDPM_ACC | IINDPM = 1500mA (TJ=-40°C-85°C) | min 1300 · typ 1390 · max 1500 mA | 10 |
| Junction temperature regulation accuracy TREG | TREG = 90°C | typ 90 °C | 11 |
| Junction temperature regulation accuracy TREG | TREG = 110°C | typ 110 °C | 11 |
| Thermal Shutdown Rising threshold TSHUT | Temperature Increasing | typ 150 °C | 11 |
| Thermal Shutdown Falling threshold TSHUT | Temperature Decreasing | typ 130 °C | 11 |
| TS pin voltage rising threshold, Charge suspended above this voltage. VT1_RISE% | As Percentage to REGN (0°C w/ 103AT) | min 72.4 · typ 73.3 · max 74.2 % | 11 |
| TS pin voltage falling threshold. Charge re-enabled to 20% of ICHG and VREG below this voltage. VT1_FALL% | As Percentage to REGN | min 71.5 · typ 72 · max 72.5 % | 11 |
| TS pin voltage rising threshold, Charge back to 20% of ICHG and VREG above this voltage. VT2_RISE% | As Percentage to REGN, JEITA_T2=5°C w/ 103AT | min 70.25 · typ 70.75 · max 71.25 % | 11 |
| TS pin voltage rising threshold, Charge back to 20% of ICHG and VREG above this voltage. VT2_RISE% | As Percentage to REGN, JEITA_T2=10°C w/ 103AT | min 67.75 · typ 68.25 · max 68.75 % | 11 |
| TS pin voltage rising threshold, Charge back to 20% of ICHG and VREG above this voltage. VT2_RISE% | As Percentage to REGN, JEITA_T2=15°C w/ 103AT | min 64.75 · typ 65.25 · max 65.75 % | 11 |
| TS pin voltage rising threshold, Charge back to 20% of ICHG and VREG above this voltage. VT2_RISE% | As Percentage to REGN, JEITA_T2=20°C w/ 103AT | min 61.75 · typ 62.25 · max 62.75 % | 11 |
| TS pin voltage falling threshold. Charge back to ICHG and VREG below this voltage. VT2_FALL% | As Percentage to REGN, JEITA_T2=5°C w/ 103AT | min 68.7 · typ 69.2 · max 69.7 % | 11 |
| TS pin voltage falling threshold. Charge back to ICHG and VREG below this voltage. VT2_FALL% | As Percentage to REGN, JEITA_T2=10°C w/ 103AT | min 66.45 · typ 66.95 · max 67.45 % | 11 |
| TS pin voltage falling threshold. Charge back to ICHG and VREG below this voltage. VT2_FALL% | As Percentage to REGN, JEITA_T2=15°C w/ 103AT | min 63.7 · typ 64.2 · max 64.7 % | 11 |
| TS pin voltage falling threshold. Charge back to ICHG and VREG below this voltage. VT2_FALL% | As Percentage to REGN, JEITA_T2=20°C w/ 103AT | min 60.7 · typ 61.2 · max 61.7 % | 11 |
| TS pin voltage falling threshold. Charge to ICHG and 4.1V below this voltage. VT3_FALL% | As Percentage to REGN, JEITA_T3=40°C w/ 103AT | min 47.75 · typ 48.25 · max 48.75 % | 11 |
| TS pin voltage falling threshold. Charge to ICHG and 4.1V below this voltage. VT3_FALL% | As Percentage to REGN, JEITA_T3=45°C w/ 103AT | min 44.25 · typ 44.75 · max 45.25 % | 11 |
| TS pin voltage falling threshold. Charge to ICHG and 4.1V below this voltage. VT3_FALL% | As Percentage to REGN, JEITA_T3=50°C w/ 103AT | min 40.2 · typ 40.7 · max 41.2 % | 11 |
| TS pin voltage falling threshold. Charge to ICHG and 4.1V below this voltage. VT3_FALL% | As Percentage to REGN, JEITA_T3=55°C w/ 103AT | min 37.2 · typ 37.7 · max 38.2 % | 11 |
| TS pin voltage rising threshold. Charge back to ICHG and VREG above this voltage. VT3_RISE% | As Percentage to REGN, JEITA_T3=40°C w/ 103AT | min 48.8 · typ 49.3 · max 49.8 % | 11 |
| TS pin voltage rising threshold. Charge back to ICHG and VREG above this voltage. VT3_RISE% | As Percentage to REGN, JEITA_T3=45°C w/ 103AT | min 45.3 · typ 45.8 · max 46.3 % | 11 |
| TS pin voltage rising threshold. Charge back to ICHG and VREG above this voltage. VT3_RISE% | As Percentage to REGN, JEITA_T3=50°C w/ 103AT | min 41.3 · typ 41.8 · max 42.3 % | 11 |
| TS pin voltage rising threshold. Charge back to ICHG and VREG above this voltage. VT3_RISE% | As Percentage to REGN, JEITA_T3=55°C w/ 103AT | min 38.5 · typ 39 · max 39.5 % | 11 |
| TS pin voltage falling threshold, charge suspended below this voltage. VT5_FALL% | As Percentage to REGN (60°C w/ 103AT) | min 33.7 · typ 34.2 · max 35.1 % | 11 |
| TS pin voltage rising threshold. Charge back to ICHG and 4.1V above this voltage. VT5_RISE% | As Percentage to REGN | min 35 · typ 35.5 · max 36 % | 11 |
| TS pin voltage rising threshold, boost mode is suspended above this voltage. VBCOLD_RISE% | As Percentage to REGN (–19.5°C w/ 103AT) | min 79.5 · typ 80 · max 80.5 % | 12 |
| TS pin voltage falling threshold VBCOLD_FALL% | As Percentage to REGN (0°C w/ 103AT) | typ 72 % | 12 |
| TS pin voltage threshold. boost mode is suspended below this voltage. VBHOT_FALL% | As Percentage to REGN, (64°C w/ 103AT) | min 30.2 · typ 31.2 · max 32.2 % | 12 |
| TS pin voltage rising threshold VBHOT_RISE% | As Percentage to REGN, (55°C w/ 103AT), REG0C[1:0]=11 | typ 39 % | 12 |
| PWM switching frequency FSW | Oscillator frequency | min 1.32 · typ 1.5 · max 1.68 MHz | 12 |
| Maximum PWM Duty Cycle DMAX | typ 97 % | 12 | |
| Battery voltage exiting boost mode VBATLOWV_OTG | VVBAT falling | min 2.6 · typ 2.8 · max 2.9 V | 12 |
| Battery voltage entering boost mode VBATLOWV_OTG | VVBAT rising | min 2.9 · typ 3 · max 3.15 V | 12 |
| Battery voltage exiting boost mode VBST_BAT | BAT fallingVVBAT | min 2.4 · typ 2.5 · max 2.6 V | 12 |
| Typical boost mode voltage regulation range VBST_RANGE | min 4.6 · max 5.15 V | 12 | |
| Boost mode voltage regulation accuracy VBST_ACC | IVBUS = 0A, BOOST_V = 5V | min 4.85 · typ 5 · max 5.15 V | 12 |
| Boost mode battery discharge current clamp on BATFET Q4 ISYS_OCP_Q4 | min 5 · typ 6 A | 12 | |
| Boost mode overvoltage threshold on PMID VBST_OVP | min 5.55 · typ 5.8 · max 6.15 V | 12 | |
| REGN LDO output voltage VREGN | VVBUS = 5V, IREGN = 20mA | min 4.58 · typ 4.7 · max 4.8 V | 12 |
| REGN LDO output voltage VREGN | VVBUS = 9V, IREGN = 20mA | min 5.6 · typ 6 · max 6.5 V | 12 |
| REGN LDO current limit IREGN | VVBUS = 5V, VREGN = 3.8V | min 50 mA | 12 |
| Input high threshold level, SDA and SCL VIH | Pull up rail 1.8V | min 1.3 V | 12 |
| Input low threshold level VIL | I2C INTERFACE (SCL, SDA); Pull up rail 1.8V | max 0.4 V | 12 |
| Output low threshold level VOL | I2C INTERFACE (SCL, SDA); Sink current = 5mA | max 0.4 V | 12 |
| High-level leakage current IBIAS | Pull up rail 1.8V | max 1 uA | 12 |
| Input high threshold level, SDA VIH_SDA | Pull up rail 1.8V | min 1.3 V | 12 |
| Input low threshold level VIL_SDA | Pull up rail 1.8V | max 0.4 V | 12 |
| Output low threshold level VOL_SDA | Sink current = 5mA | max 0.4 V | 12 |
| High-level leakage current IBIAS_SDA | Pull up rail 1.8V | max 1 uA | 12 |
| Input high threshold level, SDA VIH_SCL | Pull up rail 1.8V | min 1.3 V | 12 |
| Input low threshold level VIL_SCL | Pull up rail 1.8V | max 0.4 V | 12 |
| Output low threshold level VOL_SCL | Sink current = 5mA | max 0.4 V | 12 |
| High-level leakage current IBIAS_SCL | Pull up rail 1.8V | max 1 uA | 12 |
| Input high threshold level (/CE, PSEL) VIH | LOGIC INPUT PIN | min 1.3 V | 12 |
| Input low threshold level (/CE, PSEL) VIL | LOGIC INPUT PIN | max 0.4 V | 12 |
| High-level leakage current (/CE, PSEL) IIN_BIAS | Pull up rail 1.8V | max 1 uA | 12 |
| Output low threshold level (/INT, STAT, PMID_GOOD) VOL | Sink current = 5mA | max 0.4 V | 13 |
| High-level leakage current (/INT, STAT, PMID_GOOD) IOUT_BIAS | Pull up rail 1.8V | max 1 uA | 13 |
| VBUS OVP Reaction-time tVBUS_OV | typ 130 ns | 13 | |
| Bad adapter detection duration tPOORSRC | typ 30 ms | 13 | |
| Bad adapter detection retry wait time tPOORSRC_RETRY | typ 2 s | 13 | |
| Deglitch time for charge termination tTERM_DGL | typ 30 ms | 13 | |
| Deglitch time for recharge threshold tRECHG_DGL | typ 30 ms | 13 | |
| Typical top-off timer accuracy tTOP_OFF | TOP_OFF_TIMER[1:0]=10 | min 24 · typ 30 · max 36 min | 13 |
| Charge safety timer accuracy tSAFETY | CHG_TIMER = 20hr | min 17 · typ 20 · max 24 hr | 13 |
| Charge safety timer accuracy tSAFETY | CHG_TIMER = 10hr | min 8 · typ 10 · max 12 hr | 13 |
| QON low time to turn on BATFET and exit shipmode tSHIPMODE | –10℃ ≤ TJ ≤ 60℃ | min 0.9 · max 1.3 s | 13 |
| QON low time before BATFET full system reset tQON_RST | –10℃ ≤ TJ ≤ 60℃ | min 8 · max 12 s | 13 |
| BATFET off time during full system reset tBATFET_RST | –10℃ ≤ TJ ≤ 60℃ | min 250 · max 400 ms | 13 |
| Delay time before BATFET turn off in ship mode tBATFET_DLY | –10℃ ≤ TJ ≤ 60℃ | min 10 · max 15 s | 13 |
| SCL clock frequency fSCL | max 400 kHz | 13 | |
| Digital low-power clock fLPDIG | REGN LDO is disabled | typ 30 kHz | 13 |
| Digital power clock fDIG | typ 500 kHz | 13 | |
| Watchdog Reset time tLP_WDT | typ 160 s | 13 | |
| Watchdog Reset time tWDT | WATCHDOG REG05[5:4] = 160s | typ 160 s | 13 |
Pins, by the datasheet
22- 2 PSEL
- Power source selection: HIGH selects 500-mA input current limit; LOW selects 2.4-A; programmable in Host mode. · p. 5
- 3 PMID_GOOD
- Active high PMID good indicator; pull up to REGN through 10-kΩ; can control an external PMOS for fault protection. · p. 5
- 4 STAT
- Charger status; pull up to a logic rail through 10-kΩ; LOW charging, HIGH complete or Sleep, blinking at 1 Hz for fault suspension. · p. 5
- 5 SCL
- I2C clock; connect to the logic rail through a 10-kΩ resistor. · p. 5
- 6 SDA
- I2C data; connect to the logic rail through a 10-kΩ resistor. · p. 5
- 7 INT
- Interrupt output; pull up to a logic rail through 10-kΩ; sends an active low 256-us pulse for status and faults. · p. 5
- 8 NC
- Not connected. · p. 5
- 9 CE
- LOW enables battery charging. · p. 5
- 10 BATSNS
- Battery voltage sense; connect close to the battery positive terminal; an open or ground short sets BATSNS_STAT and selects BAT pin regulation. · p. 5
- 11 TS
- Battery thermistor input with resistor divider from REGN to TS to GND; unused input may use two 10-kΩ resistors or TS_IGNORE. · p. 5
- 12 QON
- BATFET enable and system reset input; internally pulled up to VBAT through 200 kΩ and clamped to 6.5 V. · p. 5
- 13 BAT
- Battery positive connection; internal current sensing resistor connects SYS and BAT; place 10 uF close to BAT. · p. 5
- 14 BAT
- Battery positive connection; internal current sensing resistor connects SYS and BAT; place 10 uF close to BAT. · p. 5
- 15 SYS
- Converter output; internal current sensing resistor connects SYS and BAT; place at least 10 uF close to SYS. · p. 5
- 16 SYS
- Converter output; internal current sensing resistor connects SYS and BAT; place at least 10 uF close to SYS. · p. 5
- 17 GND
- Ground. · p. 5
- 18 GND
- Ground. · p. 5
- 19 SW
- Switching node to output inductor; connect 0.047-uF bootstrap capacitor to BTST. · p. 5
- 20 SW
- Switching node to output inductor; connect 0.047-uF bootstrap capacitor to BTST. · p. 5
- 21 BTST
- PWM high-side driver supply and internal bootstrap diode cathode; connect 0.047-uF capacitor to SW. · p. 5
- 22 REGN
- PWM low-side driver supply output and internal bootstrap diode anode; place a 4.7-uF, 10-V ceramic capacitor to analog GND close to the IC. · p. 5
- 23 PMID
- Boost output connected to RBFET and HSFET drains; place remaining input capacitance to GND, typically 2x4.7 uF plus 1 nF. · p. 5
Open-source boards using it
4- 4 layers80.4 × 49.3 mm

- 2 layers165.1 × 95.3 mm

Pico concole v2 daughter board
Crem2y/pico-console-v2-pcb
pico console v2 board (firmware : https://github.com/Crem2y/pico-console-v2)
232 parts1MIT - 2 layers52 × 42 mm

- 2 layers94 × 34.3 mm

Parts like it
8BQ25890RTW
WQFN-24-EP(4x4)-40℃~+85℃ 1 12uA 3.9V~14V 5A Charging IC I2C Lithium Battery Support Support WQFN-24-EP(4x4) Battery Management ROHSTexas InstrumentsBattery ManagementBQ25611DRTW
WQFN-24(4x4)-40℃~+85℃ 1 13.5V 15uA 2.4V 3.2A Charging IC I2C Lithium Battery Support Support WQFN-24(4x4) Battery Management ROHSTexas InstrumentsBattery ManagementBQ25892RTW
WQFN-24-EP(4x4)-40℃~+85℃ 1 12uA 3.9V~14V 4.208V 5.056A Charging IC I2C Lithium Battery Support Support WQFN-24-EP(4x4) Battery Management ROHSTexas InstrumentsBattery ManagementBQ25895MRTW
WQFN-24-EP(4x4)-40℃~+85℃ 1 12uA 2.15V 3.9V~14V 4.608V 5A Charging IC I2C Lithium Battery Not supported Support WQFN-24-EP(4x4) Battery Management ROHSTexas InstrumentsBattery ManagementBQ24298RTW
WQFN-24-EP(4x4)-40℃~+85℃ 1 2.8V 20uA 3.9V~6.2V 3A 4.2V Charging IC I2C Lithium Battery Support WQFN-24-EP(4x4) Battery Management ROHSTexas InstrumentsBattery ManagementBQ25616JRTWR
WQFN-24-EP(4x4)-40℃~+85℃ 1 3A 4.35V 4V~13.5V 9.5uA Charging IC Lithium Battery Support WQFN-24-EP(4x4) Battery Management ROHSTexas InstrumentsBattery ManagementRT9467GQW
WQFN-24-EP(4x4)-40℃~+85℃ 1 170uA 4.2V 4V~14V 5A Charging IC I2C Support WQFN-24-EP(4x4) Battery Management ROHSRichtek TechBattery ManagementBQ25890HRTWR
WQFN-24(4x4)-40℃~+85℃ 1 2.5V 3.9V~14V 4.608V WQFN-24(4x4) Battery Management ROHSTexas InstrumentsBattery Management
Questions
Is there a KiCad symbol and footprint for the BQ25619RTW?
Yes. The symbol is EasyEDA_Cloud:BQ25619RTWT and the footprint EasyEDA_Cloud:WQFN-24_L4.0-W4.0-P0.50-TL-EP2.7, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the BQ25619RTW?
WQFN-24-EP(4x4), with 25 pins. Its footprint is drawn on this page.
Where is the BQ25619RTW datasheet?
Texas Instruments publishes it: the Datasheet link on this page opens it.
Where can I order the BQ25619RTW?
JLCPCB lists it as part C2864534, with 2,663 in stock; the sellers' links on this page open their listings.
What can replace the BQ25619RTW?
Parts like it in the library: the BQ25890RTW by Texas Instruments, the BQ25611DRTW by Texas Instruments, the BQ25892RTW by Texas Instruments and the BQ25895MRTW by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.
Which open-source boards use the BQ25619RTW?
4 boards in 4 repositories on GitHub; the most starred are listed on this page, with their KiCad files.