Skip to the content
12345678

AMC1311BDWVR

Texas InstrumentsExtended

-55℃~+125℃ 1.5mV 3.5nA 3uV/℃ Transimpedance Amplifier SOIC-8-300mil Special Purpose Amplifiers ROHS

Part id
ti/AMC1311BDWVR
Category
Special Purpose Amplifiers
Package
SOIC-8-300mil
Pins
8
In stock
3,262 at JLCPCB (C783598)
Used on
7 open-source boards

Overview

The AMC1311BDWVR is a special Purpose Amplifier made by Texas Instruments in a SOIC-8-300mil package with 8 pins. -55℃~+125℃ 1.5mV 3.5nA 3uV/℃ Transimpedance Amplifier SOIC-8-300mil Special Purpose Amplifiers ROHS.

PCBKit's library has its KiCad symbol (EasyEDA_Cloud:AMC1311BDWVR, from EasyEDA) and its footprint (Package_SO:SOIC-8_7.5x5.85mm_P1.27mm, from KiCad's library), ready for a KiCad board. 3,262 are in stock at JLCPCB (part C783598). 7 open-source boards in 3 repositories on GitHub use it.

Symbol

1VDD12VIN3SHTDN4GND15GND26VOUTN7VOUTP8VDD2
EasyEDA_Cloud:AMC1311BDWVRFrom EasyEDA

Footprint

12345678
Package_SO:SOIC-8_7.5x5.85mm_P1.27mmFrom KiCad's library

From the datasheet

13
Supply, least
3 V · VDD1, recommended operating min · p. 6
Supply, most
5.5 V · VDD1, recommended operating max · p. 6
Supply, absolute maximum
6.5 V · VDD1 to GND1, absolute max · p. 6
Works from
-55 °C · AMC1311B operating ambient min · p. 6
Works up to
125 °C · AMC1311B operating ambient max · p. 6
Junction, hottest
150 °C · Junction temperature absolute max · p. 6
Takes working
12.4 mA · sum of VDD1 and VDD2 typical operating currents, VDD1 = 5 V, VDD2 = 3.3 V, SHTDN low · p. 11
Takes at most
17.8 mA · sum of VDD1 and VDD2 max operating currents, both supplies between 4.5 V and 5.5 V · p. 11
Takes asleep
5.301 mA · sum of VDD1 shutdown and VDD2 typical currents, SHTDN = VDD1, 3.0 V < VDD2 < 3.6 V · p. 11
A pin gives at most
10 mA · Continuous input current absolute max, any pin except power-supply pins · p. 6
Junction to air (DWV (SOIC))
84.6 K/W · Junction-to-ambient thermal resistance · p. 7
Junction to board (DWV (SOIC))
41.1 K/W · Junction-to-board thermal resistance · p. 7
Junction to case (DWV (SOIC))
28.3 K/W · Junction-to-case top thermal resistance · p. 7

What it is and has

11
Amplifier
High-impedance, 2-V input, reinforced isolated amplifier · p. 1
Fixed gain
1 · p. 1
Offset error
±1.5 mV maximum · p. 1
Offset drift
±10 μV/°C maximum · p. 1
Gain error
±0.2% maximum · p. 1
Gain drift
±40 ppm/°C maximum · p. 1
High-side operation
3.3 V · p. 1
Common-mode transient immunity
100 kV/μs minimum · p. 1
Diagnostics
Missing high-side supply indication · p. 1
Isolation certification
5000 VRMS for 1 minute per UL1577 · p. 1
Package
DWV, 8-pin SOIC · p. 5

Specifications

83
ParameterConditionsAs printedPage
Power-supply voltageHigh-side VDD1 to GND1min -0.3 · max 6.5 V6
Power-supply voltageLow-side VDD2 to GND2min -0.3 · max 6.5 V6
Input currentContinuous, any pin except power-supply pinsmin -10 · max 10 mA6
Temperature TJJunctionmax 150 °C6
Temperature TstgStoragemin -65 · max 150 °C6
Electrostatic discharge V(ESD)Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001; ±2000 Vmax 2000 V6
Electrostatic discharge V(ESD)Charged-device model (CDM), per ANSI/ESDA/JEDEC JS-002; ±1000 Vmax 1000 V6
High-side power supplyVDD1 to GND1, AMC1311B; typ field is NOMmin 3 · typ 5 · max 5.5 V6
Low-side power supplyVDD2 to GND2; typ field is NOMmin 3 · typ 3.3 · max 5.5 V6
Input voltage before clipping output VClippingIN to GND1; typ field is NOMtyp 2.516 V6
Specified linear full-scale voltage VFSRIN to GND1min -0.1 · max 2 V6
Capacitive load CLOADOn OUTP or OUTN to GND2max 500 pF6
Capacitive load CLOADOUTP to OUTNmax 250 pF6
Resistive load RLOADOn OUTP or OUTN to GND2; values in printed NOM and MAX columnstyp 10 · max 1 kΩ6
Input voltageSHTDN to GND1; maximum VDD1min 0 V6
Specified ambient temperature TAAMC1311Bmin -55 · max 125 °C6
Junction-to-ambient thermal resistance RθJADWV (SOIC), 8 PINStyp 84.6 °C/W7
Junction-to-case (top) thermal resistance RθJC(top)DWV (SOIC), 8 PINStyp 28.3 °C/W7
Junction-to-board thermal resistance RθJBDWV (SOIC), 8 PINStyp 41.1 °C/W7
Junction-to-top characterization parameter ΨJTDWV (SOIC), 8 PINStyp 4.9 °C/W7
Junction-to-board characterization parameter ΨJBDWV (SOIC), 8 PINStyp 39.1 °C/W7
Maximum power dissipation (both sides) PDVDD1 = VDD2 = 5.5 Vmax 98 mW7
Maximum power dissipation (both sides) PDVDD1 = VDD2 = 3.6V, AMC1311B onlymax 56 mW7
Maximum power dissipation (high-side) PD1VDD1 = 5.5 Vmax 53 mW7
Maximum power dissipation (high-side) PD1VDD1 = 3.6 V, AMC1311B onlymax 30 mW7
Maximum power dissipation (low-side) PD2VDD2 = 5.5 Vmax 45 mW7
Maximum power dissipation (low-side) PD2VDD2 = 3.6 V, AMC1311B onlymax 26 mW7
External clearance CLRShortest pin-to-pin distance through air; ≥ 8.5 mmmin 8.5 mm8
External creepage CPGShortest pin-to-pin distance across the package surface; ≥ 8.5 mmmin 8.5 mm8
Distance through insulation DTIMinimum internal gap (internal clearance) of the double insulation; ≥ 0.021 mmmin 0.021 mm8
Comparative tracking index CTIDIN EN 60112 (VDE 0303-11); IEC 60112; ≥ 600 Vmin 600 V8
Maximum repetitive peak isolation voltage VIORMAt AC voltagemax 2120 VPK8
Maximum-rated isolation working voltage VIOWMAt AC voltage (sine wave)max 1500 VRMS8
Maximum-rated isolation working voltage VIOWMAt DC voltagemax 2120 VDC8
Maximum transient isolation voltage VIOTMVTEST = VIOTM, t = 60 s (qualification test)max 7000 VPK8
Maximum transient isolation voltage VIOTMVTEST = 1.2 × VIOTM, t = 1 s (100% production test)max 8400 VPK8
Maximum impulse voltage VIMPTested in air, 1.2/50-us waveform per IEC 62368-1max 9800 VPK8
Maximum surge isolation voltage VIOSMTested in oil (qualification test), 1.2/50-us waveform per IEC 62368-1max 12800 VPK8
Apparent charge qpdMethod a, after input/output safety test subgroups 2 and 3; Vini = VIOTM, tini = 60 s, Vpd(m) = 1.2 × VIORM, tm = 10 s; ≤5 pCmax 5 pC8
Apparent charge qpdMethod a, after environmental tests subgroup 1; Vini = VIOTM, tini = 60 s, Vpd(m) = 1.6 × VIORM, tm = 10 s; ≤5 pCmax 5 pC8
Apparent charge qpdMethod b1, at routine test (100% production) and preconditioning (type test), Vini = VIOTM, tini = 1 s, Vpd(m) = 1.875 × VIORM, tm = 1 s; ≤5 pCmax 5 pC8
Barrier capacitance, input to output CIOVIO = 0.5 VPP at 1 MHz; approximately 1.5 pFtyp 1.5 pF8
Pollution degreeValue 2typ 28
Withstand isolation voltage VISOUL1577; VTEST = VISO = 5000 VRMS, t = 60 s (qualification); VTEST = 1.2 × VISO = 6000 VRMS, t = 1 s (100% production test)max 5000 VRMS8
Safety input, output, or supply current ISRθJA = 84.6°C/W, VDDx = 5.5 V, TJ = 150°C, TA = 25°Cmax 268 mA9
Safety input, output, or supply current ISRθJA = 84.6°C/W, VDDx = 3.6 V, TJ = 150°C, TA = 25°C, AMC1311B onlymax 410 mA9
Safety input, output, or total power PSRθJA = 84.6°C/W, TJ = 150°C, TA = 25°Cmax 1477 mW9
Maximum safety temperature TSmax 150 °C9
Input offset voltage VOSTA = 25°C, AMC1311B; typical at VDD1 = 3.3 V; typical value includes one standard deviationmin -1.5 · typ 0.4 · max 1.5 mV10
Input offset thermal drift TCVOSAMC1311B; typical ±3min -10 · typ 3 · max 10 uV/°C10
Input resistance RINTA = 25℃typ 1 GΩ10
Input bias current IIBIN = GND1, TA = 25℃min -15 · typ 3.5 · max 15 nA10
Input capacitance CINfIN = 275 kHztyp 7 pF10
Nominal gaintyp 1 V/V10
Gain error EGTA = 25℃, AMC1311B; typical ±0.05%min -0.2 · typ 0.05 · max 0.2 %10
Gain error drift TCEGAMC1311B; typical ±5min -40 · typ 5 · max 40 ppm/°C10
NonlineartityTypical ±0.01%min -0.04 · typ 0.01 · max 0.04 %10
Total harmonic distortion THDVIN = 2 VPP, VIN > 0 V, fIN = 10 kHz, BW = 10 kHztyp -87 dB10
Signal-to-noise ratio SNRVIN = 2 VPP, fIN = 1 kHz, BW = 10 kHzmin 79 · typ 82.6 dB10
Signal-to-noise ratio SNRVIN = 2 VPP, fIN = 10 kHz, BW = 100 kHztyp 70.9 dB10
Output noiseVIN = GND1, BW = 100 kHztyp 220 uVrms10
Power-supply rejection ratio PSRRvs VDD1, at DCtyp -80 dB10
Power-supply rejection ratio PSRRvs VDD2, at DCtyp -85 dB10
Power-supply rejection ratio PSRRvs VDD1, 10 kHz / 100-mV rippletyp -65 dB10
Power-supply rejection ratio PSRRvs VDD2, 10 kHz / 100-mV rippletyp -70 dB10
Output common-mode voltage VCMoutmin 1.39 · typ 1.44 · max 1.49 V10
Clipping differential output voltage VCLIPoutVOUT = (VOUTP – VOUTN); VIN > VClippingtyp 2.49 V10
Failsafe differential output voltage VFAILSAFESHTDN = high, or VDD1 undervoltage, or VDD1 missingtyp -2.6 · max -2.5 V10
Output bandwidth BWAMC1311Bmin 220 · typ 275 kHz10
Output resistance ROUTOn OUTP or OUTN; typical <0.2 Ωtyp 0.2 Ω10
Output short-circuit currentOn OUTP or OUTN, sourcing or sinking, IN = GND1, outputs shorted to either GND or VDD2typ 14 mA10
Common-mode transient immunity CMTIAMC1311Bmin 100 · typ 150 kV/us10
Input current IINSHTDN pin, GND1 ≤ SHTDN ≤ VDD1min -70 · max 1 uA11
Input capacitance CINSHTDN pintyp 5 pF11
VDD1 undervoltage detection threshold VDD1UVVDD1 risingmin 2.5 · typ 2.7 · max 2.9 V11
VDD1 undervoltage detection threshold VDD1UVVDD1 fallingmin 2.4 · typ 2.6 · max 2.8 V11
VDD2 undervoltage detection threshold VDD2UVVDD2 risingmin 2.2 · typ 2.45 · max 2.65 V11
VDD2 undervoltage detection threshold VDD2UVVDD2 fallingmin 1.85 · typ 2 · max 2.2 V11
High-side supply current IDD13.0 V < VDD1 < 3.6 V, SHTDN = low, AMC1311B onlytyp 6 · max 8.4 mA11
High-side supply current IDD14.5 V < VDD1 < 5.5 V, SHTDN = lowtyp 7.1 · max 9.7 mA11
High-side supply current IDD1SHTDN = VDD1typ 1.3 uA11
Low-side supply current IDD23.0 V < VDD2 < 3.6 Vtyp 5.3 · max 7.2 mA11
Low-side supply current IDD24.5 V < VDD2 < 5.5 Vtyp 5.9 · max 8.1 mA11

Pins, by the datasheet

8
1 VDD1
High-side power supply. · p. 5
2 IN
Analog input. · p. 5
3 SHTDN
Active-high shutdown input with internal pullup resistor, typically 100 kΩ. · p. 5
4 GND1
High-side analog ground. · p. 5
5 GND2
Low-side analog ground. · p. 5
6 OUTN
Inverting analog output. · p. 5
7 OUTP
Noninverting analog output. · p. 5
8 VDD2
Low-side power supply. · p. 5

Open-source boards using it

7
  • 4 layers300 × 150 mmDab secondary, the printed circuit board in 3D

    Dab secondary

    FulongLi/AIPE-PCB-Agent

    AIPE-PCB-Agent is the PCB design automation of the AIPE power-electronics ecosystem. Python generators turn a requirement file set (specification, insulation table, components, interfaces, floorplan and routing inputs)…

    312 parts
  • 4 layers246.8 × 154.7 mmAc psu, the printed circuit board in 3D

    Ac psu

    johonkanen/ac_psu_kicad

    test full kicad conversion of latest ac_psu hardware files done by claude. originally drawn in proteus

    377 partsMIT
  • 6 layers220 × 160 mmSection, the printed circuit board in 3D

    Section

    BennetLeff/temper

    a breville control freak ++

    91 parts1
  • 4 layers240 × 160 mmSection, the printed circuit board in 3D

    Section

    BennetLeff/temper

    a breville control freak ++

    135 parts1
  • 4 layers240 × 180 mmAIPE SiC Buck Power, the printed circuit board in 3D

    AIPE SiC Buck Power

    FulongLi/AIPE-PCB-Agent

    AIPE-PCB-Agent is the PCB design automation of the AIPE power-electronics ecosystem. Python generators turn a requirement file set (specification, insulation table, components, interfaces, floorplan and routing inputs)…

    237 parts
  • 4 layers300 × 150 mmDab primary, the printed circuit board in 3D

    Dab primary

    FulongLi/AIPE-PCB-Agent

    AIPE-PCB-Agent is the PCB design automation of the AIPE power-electronics ecosystem. Python generators turn a requirement file set (specification, insulation table, components, interfaces, floorplan and routing inputs)…

    309 parts
  • 4 layers250 × 180 mmSic v3-power, the printed circuit board in 3D

    Sic v3-power

    FulongLi/AIPE-PCB-Agent

    AIPE-PCB-Agent is the PCB design automation of the AIPE power-electronics ecosystem. Python generators turn a requirement file set (specification, insulation table, components, interfaces, floorplan and routing inputs)…

    202 parts

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the AMC1311BDWVR?

Yes. The symbol is EasyEDA_Cloud:AMC1311BDWVR and the footprint Package_SO:SOIC-8_7.5x5.85mm_P1.27mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the AMC1311BDWVR?

SOIC-8-300mil, with 8 pins. Its footprint is drawn on this page.

Where is the AMC1311BDWVR datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the AMC1311BDWVR?

JLCPCB lists it as part C783598, with 3,262 in stock; the sellers' links on this page open their listings.

What can replace the AMC1311BDWVR?

Parts like it in the library: the ISO224BDWVR by Texas Instruments, the AMC1300DWVR by Texas Instruments, the SI8921AD-IS4 by Silicon Labs and the SI8922AD-IS4 by Silicon Labs. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the AMC1311BDWVR?

7 boards in 3 repositories on GitHub; the most starred are listed on this page, with their KiCad files.