Skip to the content

ADS1298IPAGR

Texas InstrumentsExtended

-40℃~+85℃ 1.94MHz~2.048MHz、2.048MHz 112dB 2.5V 2.7V~5.25V 24 32kHz 32kHz 5ppm/℃ SPI TQFP-64(10x10) Analog Front End (AFE) ROHS

Part id
ti/ADS1298IPAGR
Category
Analog Front End (AFE)
Package
TQFP-64(10x10)
Pins
64
In stock
1,687 at JLCPCB (C527440)
Used on
8 open-source boards

Overview

The ADS1298IPAGR is an analog Front End made by Texas Instruments in a TQFP-64(10x10) package with 64 pins. -40℃~+85℃ 1.94MHz~2.048MHz、2.048MHz 112dB 2.5V 2.7V~5.25V 24 32kHz 32kHz 5ppm/℃ SPI TQFP-64(10x10) Analog Front End (AFE) ROHS.

PCBKit's library has its KiCad symbol (Analog_ADC:ADS1298xPAG, from KiCad's library) and its footprint (Package_QFP:TQFP-64_10x10mm_P0.5mm, from KiCad's library), ready for a KiCad board. 1,687 are in stock at JLCPCB (part C527440). 8 open-source boards in 5 repositories on GitHub use it.

Symbol

1IN8N2IN8P3IN7N4IN7P5IN6N6IN6P7IN5N8IN5P9IN4N10IN4P11IN3N12IN3P13IN2N14IN2P15IN1N16IN1P17TESTP_PACE_OUT118TESTP_PACE_OUT219AVDD20AVSS24VREFP25VREFN26VCAP428VCAP130VCAP231RESV133DGND34DIN35PWDN36RESET37CLK38START39CS40SCLK41DAISY_IN42GPIO143DOUT44GPIO245GPIO346GPIO447DRDY48DVDD52CLKSEL53AVSS154AVDD155VCAP360RLDREF61RLDINV62RLDIN63RLDOUT64WCT
Analog_ADC:ADS1298xPAGFrom KiCad's library

Footprint

Package_QFP:TQFP-64_10x10mm_P0.5mmFrom KiCad's library

From the datasheet

13
Supply, least
2.7 V · AVDD – AVSS, recommended operating min · p. 12
Supply, most
5.25 V · AVDD – AVSS, recommended operating max · p. 12
Supply, least
1.65 V · DVDD, recommended operating min · p. 12
Supply, most
3.6 V · DVDD, recommended operating max · p. 12
Supply, absolute maximum
5.5 V · AVDD to AVSS, absolute max · p. 12
Supply, absolute maximum
3.9 V · DVDD to DGND, absolute max · p. 12
Works from
-40 °C · Industrial grade operating ambient min · p. 12
Works up to
85 °C · Industrial grade operating ambient max · p. 12
Junction, hottest
150 °C · Junction temperature absolute max · p. 12
Junction to air (PAG (TQFP))
35 K/W · Junction-to-ambient thermal resistance · p. 13
Junction to case (PAG (TQFP))
31 K/W · Junction-to-case (top) thermal resistance · p. 13
Junction to board (PAG (TQFP))
26 K/W · Junction-to-board thermal resistance · p. 13
Takes working
3.05 mA · sum of AVDD and DVDD typical currents, HR mode, AVDD – AVSS = 3 V, DVDD = 1.8 V; RLD, WCT and PACE off · p. 16

What it is and has

14
Architecture
8-channel, 24-bit analog front end for biopotential measurements · p. 1
Power
0.75 mW/channel · p. 1
Input-referred noise
4 μVPP (150 Hz BW, G = 6) · p. 1
Input bias current
200 pA · p. 1
Data rate
250 SPS to 32 kSPS · p. 1
CMRR
–115 dB · p. 1
Programmable gain
1, 2, 3, 4, 6, 8, or 12 · p. 1
Pace detection
Digital pace detection capability · p. 1
Oscillator and reference
Built-in · p. 1
Serial interface
SPI-compatible · p. 1
ADC
8-channel, 24-bit · p. 1
Power consumption
0.75 mW/channel · p. 1
Temperature sensor
On-chip · p. 28
Respiration measurement
External respiration impedance measurement · p. 46

Around it

6
cap 1-μF
between VCAP4 and AVSS; Analog bypass capacitor. · p. 10
cap 22-μF
between VCAP1 and AVSS; Analog bypass capacitor. · p. 10
cap 1-μF
between VCAP2 and AVSS; Analog bypass capacitor. · p. 10
cap 1-μF
between VCAP3 and AVSS; Analog bypass capacitor; VCAP3 is internally generated AVDD + 1.9 V. · p. 11
res 10-kΩ
between NC (27) and AVDD or AVSS; Optional connection for no-connect pin. · p. 10
res 10-kΩ
between NC (29) and AVDD or AVSS; Optional connection for no-connect pin. · p. 10

Specifications

148
ParameterConditionsAs printedPage
AVDD to AVSSOver operating free-air temperature rangemin -0.3 · max 5.5 V12
DVDD to DGNDOver operating free-air temperature rangemin -0.3 · max 3.9 V12
AVSS to DGNDOver operating free-air temperature rangemin -3 · max 0.2 V12
Input current (momentary)max 100 mA12
Input current (continuous)max 10 mA12
Junction temperature TJmin -40 · max 150 °C12
Storage temperature Tstgmin -60 · max 150 °C12
Electrostatic discharge V(ESD)Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins; ±2000 Vmax 2000 V12
Electrostatic discharge V(ESD)Charged device model (CDM), per JEDEC specification JESD22-C101, all pins; ±500 Vmax 500 V12
Analog power supply (AVDD – AVSS)Over operating ambient temperature range; NOM = 3 Vmin 2.7 · typ 3 · max 5.25 V12
Digital power supply (DVDD)Over operating ambient temperature range; NOM = 1.8 Vmin 1.65 · typ 1.8 · max 3.6 V12
AVDD – DVDDmin -2.1 · max 3.6 V12
Differential reference voltage3-V supply VREF = (VREFP – VREFN); NOM = 2.5 Vtyp 2.5 V12
Differential reference voltage5-V supply VREF = (VREFP – VREFN); NOM = 4 Vtyp 4 V12
External clock input frequencyCLKSEL pin = 0; NOM = 2.048 MHzmin 1.94 · typ 2.048 · max 2.25 MHz12
Operating temperature rangeIndustrial grade; TQFPmin -40 · max 85 °C12
Junction-to-ambient thermal resistance RθJAPAG (TQFP), 64 pinstyp 35 °C/W13
Junction-to-case (top) thermal resistance RθJC(top)PAG (TQFP), 64 pinstyp 31 °C/W13
Junction-to-board thermal resistance RθJBPAG (TQFP), 64 pinstyp 26 °C/W13
Junction-to-top characterization parameter ψJTPAG (TQFP), 64 pinstyp 0.1 °C/W13
Input capacitancetyp 20 pF13
Input bias currentTA = 25°C, input = 1.5 V; maximum ±200 pAmax 200 pA13
Input bias currentTA = 0°C to 70°C, input = 1.5 V; typical ±1 nAtyp 1 nA13
Input bias currentTA = –40°C to +85°C, input = 1.5 V; typical ±1.2 nAtyp 1.2 nA13
DC input impedanceNo lead-offmin 1000 MΩ13
DC input impedanceCurrent source lead-off detectiontyp 500 MΩ13
DC input impedancePullup resistor lead-off detectiontyp 10 MΩ13
ResolutionData rates up to 8 kSPS, no missing codesmin 24 Bits13
Resolution16-kSPS data ratemin 19 Bits13
Resolution32-kSPS data ratemin 17 Bits13
Data ratefCLK = 2.048 MHz, HR modemin 500 · max 32000 SPS13
Data ratefCLK = 2.048 MHz, LP modemin 250 · max 16000 SPS13
Input-referred noiseGain = 6, 10 seconds of datatyp 5 uVPP13
Input-referred noiseGain = 6, 256 points, 0.5 seconds of datatyp 4 · max 7 uVPP13
Integral nonlinearityFull-scale with gain = 6, best fittyp 8 ppm13
Offset errorTypical ±500 uVtyp 500 uV13
Offset error drifttyp 2 uV/°C13
Gain errorExcluding voltage reference error; typical ±0.2, maximum ±0.5typ 0.2 · max 0.5 % of FS13
Gain driftExcluding voltage reference drifttyp 5 ppm/°C13
Gain match between channelstyp 0.3 % of FS13
Common-mode rejection ratio CMRRfCM = 50 Hz, 60 Hzmin -105 · typ -115 dB14
Power-supply rejection ratio PSRRfPS = 50 Hz, 60 Hztyp 90 dB14
CrosstalkfIN = 50 Hz, 60 Hztyp -126 dB14
Signal-to-noise ratio SNRfIN = 10 Hz input, gain = 6typ 112 dB14
Total harmonic distortion THD10 Hz, –0.5 dBFstyp -98 dB14
Total harmonic distortion THD100 Hz, –0.5 dBFstyp -100 dB14
Digital filter settlingFull settingtyp 4 Conversions14
RLD integrated noiseBW = 150 Hztyp 7 uVRMS14
Pace integrated noiseBW = 8 kHztyp 20 uVRMS14
Pace-amplifier crosstalkCrosstalk between pace amplifierstyp 60 dB14
Gain bandwidth productRLD and pace amplifiers; 50 kΩ || 10 pF load, gain = 1typ 100 kHz14
Slew rateRLD and pace amplifiers; 50 kΩ || 10 pF load, gain = 1typ 0.25 V/us14
Pace and RLD amplifier drive strengthShort circuit to GND (AVDD = 3 V)typ 270 uA14
Pace and RLD amplifier drive strengthShort circuit to supply (AVDD = 3 V)typ 550 uA14
Pace and RLD amplifier drive strengthShort circuit to GND (AVDD = 5 V)typ 490 uA14
Pace and RLD amplifier drive strengthShort circuit to supply (AVDD = 5 V)typ 810 uA14
Pace and RLD currentPeak swing (AVSS + 0.3 V to AVDD + 0.3 V) at AVDD = 3 Vtyp 50 uA14
Pace and RLD currentPeak swing (AVSS + 0.3 V to AVDD + 0.3 V) at AVDD = 5 Vtyp 75 uA14
Pace-amplifier output resistancetyp 100 Ω14
Total harmonic distortionRLD and pace amplifiers; fIN = 100 Hz, gain = 1typ -70 dB14
Common-mode resistor matchingInternal 200-kΩ resistor matchingtyp 0.1 %14
Short-circuit currentRLD and pace amplifiers; typical ±0.25 mAtyp 0.25 mA14
Quiescent power consumptionEither RLD or pace amplifiertyp 20 uA14
Total harmonic distortionWCT amplifier; fIN = 100 Hztyp 90 dB14
Short-circuit currentWCT amplifier; Through internal 30-kΩ resistor; typical ±0.25 mAtyp 0.25 mA14
CurrentLEAD-OFF DETECT; See Table 16 for settings; 6 nA settingtyp 6 nA15
CurrentLEAD-OFF DETECT; See Table 16 for settings; 12 nA settingtyp 12 nA15
CurrentLEAD-OFF DETECT; See Table 16 for settings; 18 nA settingtyp 18 nA15
CurrentLEAD-OFF DETECT; See Table 16 for settings; 24 nA settingtyp 24 nA15
Current accuracyLEAD-OFF DETECT; typical ±20%typ 20 %15
Comparator threshold accuracyLEAD-OFF DETECT; typical ±30 mVtyp 30 mV15
Input impedanceEXTERNAL REFERENCEtyp 10 kΩ15
Output voltageINTERNAL REFERENCE; Register bit CONFIG3.VREF_4V = 0, AVDD ≥ 2.7 Vtyp 2.4 V15
Output voltageINTERNAL REFERENCE; Register bit CONFIG3.VREF_4V = 1, AVDD ≥ 4.4 Vtyp 4 V15
VREF accuracyINTERNAL REFERENCE; typical ±0.2%typ 0.2 %15
Internal reference driftTA = 25°Ctyp 35 ppm/°C15
Internal reference driftIndustrial grade, –40°C to 85°Ctyp 45 ppm15
Start-up timeINTERNAL REFERENCEtyp 150 ms15
Analog-supply reading errorSYSTEM MONITORStyp 2 %15
Digital-supply reading errorSYSTEM MONITORStyp 2 %15
Device wakeupFrom power up to DRDY lowtyp 150 ms15
Device wakeupSTANDBY modetyp 9 ms15
Temperature-sensor reading, voltageTA = 25°Ctyp 145 mV15
Temperature-sensor reading, coefficienttyp 490 uV/°C15
Test-signal voltageSee Table 16 for settings; ±1 mV settingtyp 1 mV15
Test-signal voltageSee Table 16 for settings; ±2 mV settingtyp 2 mV15
Test-signal accuracyTypical ±2%typ 2 %15
Internal-oscillator clock frequencyNominal frequencytyp 2.048 MHz15
Internal clock accuracyTA = 25°C; maximum ±0.5%max 0.5 %15
Internal clock accuracy0°C ≤ TA ≤ 70°C; maximum ±2%max 2 %15
Internal clock accuracy–40°C ≤ TA ≤ 85°C, industrial grade versions only; maximum ±2.5%max 2.5 %15
Internal-oscillator start-up timemax 20 us15
Internal-oscillator power consumptiontyp 120 uW15
Low-level input voltage VILDVDD = 1.65 V to 3.6 V; maximum 0.2 DVDDmin -0.1 V16
Low-level output voltage VOLDVDD = 1.65 V to 3.6 V; IOL = 500 uAmax 0.4 V16
Input current IINDVDD = 1.65 V to 3.6 V; 0 V < VDigitalInput < DVDDmin -10 · max 10 uA16
AVDD current IAVDDADS1298; AVDD – AVSS = 3 V; HR mode; RLD, WCT, and PACE amplifiers turned offtyp 2.75 mA16
AVDD current IAVDDADS1298; AVDD – AVSS = 3 V; LP mode (2); RLD, WCT, and PACE amplifiers turned offtyp 1.8 mA16
AVDD current IAVDDADS1298; AVDD – AVSS = 5 V; HR mode; RLD, WCT, and PACE amplifiers turned offtyp 3.1 mA16
AVDD current IAVDDADS1298; AVDD – AVSS = 5 V; LP mode; RLD, WCT, and PACE amplifiers turned offtyp 2.1 mA16
DVDD current IDVDDADS1298; DVDD = 1.8 V; HR mode; RLD, WCT, and PACE amplifiers turned offtyp 0.3 mA16
DVDD current IDVDDADS1298; DVDD = 1.8 V; LP mode; RLD, WCT, and PACE amplifiers turned offtyp 0.3 mA16
DVDD current IDVDDADS1298; DVDD = 3 V; HR mode; RLD, WCT, and PACE amplifiers turned offtyp 0.5 mA16
DVDD current IDVDDADS1298; DVDD = 3 V; LP mode; RLD, WCT, and PACE amplifiers turned offtyp 0.5 mA16
Power dissipationADS1298; AVDD – AVSS = 3 V; HR mode; RLD, WCT, and PACE amplifiers turned offtyp 8.8 · max 9.5 mW16
Power dissipationADS1298; AVDD – AVSS = 3 V; LP mode (250 SPS); RLD, WCT, and PACE amplifiers turned offtyp 6 · max 7 mW16
Power dissipationADS1298; AVDD – AVSS = 5 V; HR mode; RLD, WCT, and PACE amplifiers turned offtyp 17.5 mW16
Power dissipationADS1298; AVDD – AVSS = 5 V; LP mode (250 SPS); RLD, WCT, and PACE amplifiers turned offtyp 12.5 mW16
Power-downAVDD – AVSS = 3 Vtyp 10 uW16
Power-downAVDD – AVSS = 5 Vtyp 20 uW16
Standby modeAVDD – AVSS = 3 Vtyp 2 mW16
Standby modeAVDD – AVSS = 5 Vtyp 4 mW16
Quiescent channel powerAVDD – AVSS = 3 V, PGA + ADCtyp 818 uW16
Quiescent channel powerAVDD – AVSS = 5 V, PGA + ADCtyp 1.5 mW16
Master clock period tCLK2.7 V ≤ DVDD ≤ 3.6 V; TA = –40°C to +85°C; DOUT load = 20 pF || 100 kΩmin 414 · max 514 ns17
Master clock period tCLK1.65 V ≤ DVDD ≤ 2 V; TA = –40°C to +85°C; DOUT load = 20 pF || 100 kΩmin 414 · max 514 ns17
CS low to first SCLK, setup time tCSSC2.7 V ≤ DVDD ≤ 3.6 Vmin 6 ns17
CS low to first SCLK, setup time tCSSC1.65 V ≤ DVDD ≤ 2 Vmin 17 ns17
SCLK period tSCLK2.7 V ≤ DVDD ≤ 3.6 Vmin 50 ns17
SCLK period tSCLK1.65 V ≤ DVDD ≤ 2 Vmin 66.6 ns17
SCLK pulse width, high and low tSPWH, L2.7 V ≤ DVDD ≤ 3.6 Vmin 15 ns17
SCLK pulse width, high and low tSPWH, L1.65 V ≤ DVDD ≤ 2 Vmin 25 ns17
DIN valid to SCLK falling edge: setup time tDIST2.7 V ≤ DVDD ≤ 3.6 Vmin 10 ns17
DIN valid to SCLK falling edge: setup time tDIST1.65 V ≤ DVDD ≤ 2 Vmin 10 ns17
Valid DIN after SCLK falling edge: hold time tDIHD2.7 V ≤ DVDD ≤ 3.6 Vmin 10 ns17
Valid DIN after SCLK falling edge: hold time tDIHD1.65 V ≤ DVDD ≤ 2 Vmin 11 ns17
CS high pulse tCSH2.7 V ≤ DVDD ≤ 3.6 Vmin 2 tCLK17
CS high pulse tCSH1.65 V ≤ DVDD ≤ 2 Vmin 2 tCLK17
Eighth SCLK falling edge to CS high tSCCS2.7 V ≤ DVDD ≤ 3.6 Vmin 4 tCLK17
Eighth SCLK falling edge to CS high tSCCS1.65 V ≤ DVDD ≤ 2 Vmin 4 tCLK17
Command decode time tSDECODE2.7 V ≤ DVDD ≤ 3.6 Vmin 4 tCLK17
Command decode time tSDECODE1.65 V ≤ DVDD ≤ 2 Vmin 4 tCLK17
DAISY_IN valid to SCLK rising edge: setup time tDISCK2ST2.7 V ≤ DVDD ≤ 3.6 Vmin 10 ns17
DAISY_IN valid to SCLK rising edge: setup time tDISCK2ST1.65 V ≤ DVDD ≤ 2 Vmin 10 ns17
DAISY_IN valid after SCLK rising edge: hold time tDISCK2HT2.7 V ≤ DVDD ≤ 3.6 Vmin 10 ns17
DAISY_IN valid after SCLK rising edge: hold time tDISCK2HT1.65 V ≤ DVDD ≤ 2 Vmin 10 ns17
SCLK falling edge to invalid DOUT: hold time tDOHD2.7 V ≤ DVDD ≤ 3.6 V; TA = –40°C to +85°C; DOUT load = 20 pF || 100 kΩmin 10 ns17
SCLK falling edge to invalid DOUT: hold time tDOHD1.65 V ≤ DVDD ≤ 2 V; TA = –40°C to +85°C; DOUT load = 20 pF || 100 kΩmin 10 ns17
SCLK rising edge to DOUT valid: setup time tDOPD2.7 V ≤ DVDD ≤ 3.6 V; TA = –40°C to +85°C; DOUT load = 20 pF || 100 kΩmax 17 ns17
SCLK rising edge to DOUT valid: setup time tDOPD1.65 V ≤ DVDD ≤ 2 V; TA = –40°C to +85°C; DOUT load = 20 pF || 100 kΩmax 32 ns17
CS low to DOUT driven tCSDOD2.7 V ≤ DVDD ≤ 3.6 V; TA = –40°C to +85°C; DOUT load = 20 pF || 100 kΩmin 10 ns17
CS low to DOUT driven tCSDOD1.65 V ≤ DVDD ≤ 2 V; TA = –40°C to +85°C; DOUT load = 20 pF || 100 kΩmin 20 ns17
CS high to DOUT Hi-Z tCSDOZ2.7 V ≤ DVDD ≤ 3.6 V; TA = –40°C to +85°C; DOUT load = 20 pF || 100 kΩmax 10 ns17
CS high to DOUT Hi-Z tCSDOZ1.65 V ≤ DVDD ≤ 2 V; TA = –40°C to +85°C; DOUT load = 20 pF || 100 kΩmax 20 ns17
Respiration phase delay, set by RESP.RESP_PH[2:0] tPHASE2.7 V ≤ DVDD ≤ 3.6 V; –40°C to 85°Cmin 22.5 · max 157.5 Degrees46
Respiration phase delay, set by RESP.RESP_PH[2:0] tPHASE1.65 V ≤ DVDD ≤ 2 V; –40°C to 85°Cmin 22.5 · max 157.5 Degrees46
Modulation clock rising edge to XOR signal tBLKDLY2.7 V ≤ DVDD ≤ 3.6 V; –40°C to 85°Ctyp 1 ns46
Modulation clock rising edge to XOR signal tBLKDLY1.65 V ≤ DVDD ≤ 2 V; –40°C to 85°Ctyp 5 ns46

Pins, by the datasheet

64
1 IN8N
Differential analog negative input 8. · p. 10
2 IN8P
Differential analog positive input 8. · p. 10
3 IN7N
Differential analog negative input 7. · p. 10
4 IN7P
Differential analog positive input 7. · p. 10
5 IN6N
Differential analog negative input 6. · p. 10
6 IN6P
Differential analog positive input 6. · p. 10
7 IN5N
Differential analog negative input 5. · p. 10
8 IN5P
Differential analog positive input 5. · p. 10
9 IN4N
Differential analog negative input 4. · p. 10
10 IN4P
Differential analog positive input 4. · p. 10
11 IN3N
Differential analog negative input 3. · p. 10
12 IN3P
Differential analog positive input 3. · p. 10
13 IN2N
Differential analog negative input 2. · p. 10
14 IN2P
Differential analog positive input 2. · p. 10
15 IN1N
Differential analog negative input 1. · p. 10
16 IN1P
Differential analog positive input 1. · p. 10
17 TESTP_PACE_OUT1
Internal test signal/single-ended buffer output based on register settings. · p. 10
18 TESTN_PACE_OUT2
Internal test signal/single-ended buffer output based on register settings. · p. 10
19 AVDD
Analog supply. · p. 10
20 AVSS
Analog ground. · p. 10
21 AVDD
Analog supply. · p. 10
22 AVDD
Analog supply. · p. 10
23 AVSS
Analog ground. · p. 10
24 VREFP
Positive reference input/output voltage. · p. 10
25 VREFN
Negative reference voltage. · p. 10
26 VCAP4
Analog bypass capacitor; connect 1-uF capacitor to AVSS. · p. 10
27 NC
No connection; can be connected to AVDD or AVSS with a 10-kΩ resistor. · p. 10
28 VCAP1
Analog bypass capacitor; connect 22-uF capacitor to AVSS. · p. 10
29 NC
No connection; can be connected to AVDD or AVSS with a 10-kΩ resistor. · p. 10
30 VCAP2
Analog bypass capacitor; connect 1-uF capacitor to AVSS. · p. 10
31 RESV1
Reserved for future use; must tie to logic low (DGND). · p. 10
32 AVSS
Analog ground. · p. 10
33 DGND
Digital ground. · p. 10
34 DIN
SPI data input. · p. 10
35 PWDN
Power-down pin; active low. · p. 10
36 RESET
System-reset pin; active low. · p. 10
37 CLK
External Master clock input or internal clock output. · p. 10
38 START
Start conversion. · p. 10
39 CS
SPI chip select; active low. · p. 10
40 SCLK
SPI clock. · p. 10
41 DAISY_IN
Daisy-chain input; if not used, short to DGND. · p. 10
42 GPIO1
General-purpose input/output pin 1. · p. 11
43 DOUT
SPI data output. · p. 11
44 GPIO2
General-purpose input/output pin 2. · p. 11
45 GPIO3
General-purpose input/output pin 3. · p. 11
46 GPIO4
General-purpose input/output pin 4. · p. 11
47 DRDY
Data ready; active low. · p. 11
48 DVDD
Digital power supply. · p. 11
49 DGND
Digital ground. · p. 11
50 DVDD
Digital power supply. · p. 11
51 DGND
Digital ground. · p. 11
52 CLKSEL
Master clock select. · p. 11
53 AVSS1
Analog ground. · p. 11
54 AVDD1
Analog supply. · p. 11
55 VCAP3
Analog bypass capacitor; internally generated AVDD + 1.9 V; connect 1-uF capacitor to AVSS. · p. 11
56 AVDD
Analog supply. · p. 11
57 AVSS
Analog ground. · p. 11
58 AVSS
Analog ground. · p. 11
59 AVDD
Analog supply. · p. 11
60 RLDREF
Right leg drive noninverting input. · p. 11
61 RLDINV
Right leg drive inverting input. · p. 11
62 RLDIN
Right leg drive input to mux. · p. 11
63 RLDOUT
Right leg drive output. · p. 11
64 WCT
Wilson Central Terminal output. · p. 11

Open-source boards using it

8
  • 4 layers28.7 × 27 mmNeurband c, the printed circuit board in 3D

    Neurband c

    jlcjak/neurband

    Open, minimal sEMG wristband like the Meta Neural Band: 8-ch ADS1298 + nRF52832 BLE, dry gold electrodes on a flex, 3D-printed band. KiCad, FreeCAD, Zephyr, Python, simulations.

    70 parts46
  • 4 layers162.6 × 61.5 mmVersaSens HeEx, the printed circuit board in 3D

    VersaSens HeEx

    esl-epfl/VersaSens

    VersaSens: An Extendable Multimodal Platform for Next-Generation Edge-AI Wearables

    335 parts9
  • 4 layers65 × 52.3 mmAds1298, the printed circuit board in 3D

    Ads1298

    Genabl/parasitic_monorepo

    Second-board regression target for the volume-conductor pipeline.

    229 partsMIT
  • 4 layers68 × 46 mmUtter, the printed circuit board in 3D

    Utter

    IFAKA/utter

    Utter: covert silent-speech text input from surface EMG (open-source ALS voice)

    107 parts
  • 4 layers28.7 × 27 mmNeurband c old, the printed circuit board in 3D

    Neurband c old

    jlcjak/neurband

    Open, minimal sEMG wristband like the Meta Neural Band: 8-ch ADS1298 + nRF52832 BLE, dry gold electrodes on a flex, 3D-printed band. KiCad, FreeCAD, Zephyr, Python, simulations.

    69 parts46
  • 4 layers54 × 34 mmNeurband main, the printed circuit board in 3D

    Neurband main

    jlcjak/neurband

    Open, minimal sEMG wristband like the Meta Neural Band: 8-ch ADS1298 + nRF52832 BLE, dry gold electrodes on a flex, 3D-printed band. KiCad, FreeCAD, Zephyr, Python, simulations.

    63 parts46
  • 4 layers32 × 26 mmNeurband main, the printed circuit board in 3D

    Neurband main

    jlcjak/neurband

    Open, minimal sEMG wristband like the Meta Neural Band: 8-ch ADS1298 + nRF52832 BLE, dry gold electrodes on a flex, 3D-printed band. KiCad, FreeCAD, Zephyr, Python, simulations.

    60 parts46
  • 2 layers66.6 × 60.9 mmStetho-01, the printed circuit board in 3D

    Stetho-01

    jibonaronno/documentsA

    It is required to change settings using SCLManager.exe when required for new setup.

    2 parts4

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the ADS1298IPAGR?

Yes. The symbol is Analog_ADC:ADS1298xPAG and the footprint Package_QFP:TQFP-64_10x10mm_P0.5mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the ADS1298IPAGR?

TQFP-64(10x10), with 64 pins. Its footprint is drawn on this page.

Where is the ADS1298IPAGR datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the ADS1298IPAGR?

JLCPCB lists it as part C527440, with 1,687 in stock; the sellers' links on this page open their listings.

What can replace the ADS1298IPAGR?

Parts like it in the library: the ADS1299-4PAGR by Texas Instruments, the ADS131E08IPAGR by Texas Instruments, the ADS1299IPAGR by Texas Instruments and the ADS1298IPAG by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the ADS1298IPAGR?

8 boards in 5 repositories on GitHub; the most starred are listed on this page, with their KiCad files.