Skip to the content
29

GC6609

SX-globalchipExtended

-40℃~+125℃ 2A 2、4、8、16 3V~5.5V 4.7V~36V 400mΩ Yes QFN-28 Stepper Motor Driver ROHS

Part id
sx-globalchip/GC6609
Category
Stepper Motor Driver
Package
QFN-28
Pins
29
In stock
0 at JLCPCB (C16197208)
Used on
1 open-source board

Overview

The GC6609 is a stepper Motor Driver made by SX-globalchip in a QFN-28 package with 29 pins. -40℃~+125℃ 2A 2、4、8、16 3V~5.5V 4.7V~36V 400mΩ Yes QFN-28 Stepper Motor Driver ROHS.

PCBKit's library has its KiCad symbol (EasyEDA_Cloud:GC6609_C16197208, from EasyEDA) and its footprint (EasyEDA_Cloud:QFN-28_L5.0-W5.0-P0.50-BL-EP, from EasyEDA), ready for a KiCad board. JLCPCB lists it (part C16197208). 1 open-source board in 1 repository on GitHub use it.

Symbol

1OUT2B2ENABLE3GND4CP15CP26VCP7NC8VREG9MS110MS211FLAG112FLAG213CLK14HOLDEN15VIO16STEP17REF18GND19DIR20NC21OUT1B22VBB123SENSE124OUT1A25PGND26OUT2A27SENSE228VBB229EP
EasyEDA_Cloud:GC6609_C16197208From EasyEDA

Footprint

29
EasyEDA_Cloud:QFN-28_L5.0-W5.0-P0.50-BL-EPFrom EasyEDA

From the datasheet

10
Supply, least
4.7 V · VBB, recommended operating min · p. 5
Supply, most
36 V · VBB, recommended operating max · p. 5
Supply, least
3 V · VIO, recommended operating min · p. 5
Supply, most
5.5 V · VIO, recommended operating max · p. 5
Supply, absolute maximum
40 V · VBB, absolute max with inductive load · p. 5
Supply, absolute maximum
6 V · VIO, absolute max · p. 5
Works from
-40 °C · Operating temperature min · p. 5
Works up to
125 °C · Operating temperature max · p. 5
Gives
2 A · RMS motor coil current max per coil · p. 5
Edge
60 ns · Output rise time typical, 24V, 24Ω resistive load, 20% to 80% · p. 6

What it is and has

8
Motor driver
Two-phase stepper; 2A RMS, 4A peak · p. 1
Step control
STEP/DIR; maximum 256 microsteps; MS1/MS2 resolution selection · p. 1
Automatic gain control
Automatic torque compensation across a wide speed range · p. 1
Power saving
Automatic when motor is held · p. 1
Protection
Overtemperature and undervoltage protection · p. 1
Status indication
FLAG error and state indication · p. 1
Package
QFN28 · p. 1
UART
One-wire interface · p. 1

Around it

3
cap 22nF
between CP1 and CP2; 50V charge pump capacitor. · p. 2
cap 2.2µF to 4.7µF
between VREG and GND; Ceramic; place nearby with the shortest possible loop to the GND pad. · p. 2
cap 0.1uF
between VBB and VCP; 50V charge pump capacitor. · p. 9

Specifications

37
ParameterConditionsAs printedPage
Supply voltage operating with inductive load VBBmin -0.5 · max 40 V5
I/O supply voltage VIOmin -0.5 · max 6 V5
Logic input / output (STEP, DIR,CLK, ENABLE,MS1,MS2,HOLDEN,FLAG1, FLAG2)Maximum: VIOmin -0.5 V5
Current sense pin SENSEmin -0.5 · max 0.5 V5
Current scale setting pin REFmin -0.5 · max 6 V5
LDO Maximum output current VREGmax 50 mA5
Maximum sine wave peak current Ipeakmax 4 A5
Operating temperature Toprmin -40 · max 125 ℃5
Storage temperature Tstgmin -60 · max 150 ℃5
ESD-Protection for interface pins (Human body model,HBM) ESDHuman body model, HBMmin -4000 · max 4000 V5
Power supply voltage VBBmin 4.7 · max 36 V5
Logic supply voltage VIOmin 3 · max 5.5 V5
Logic input / outputmin -0.5 · max 7 V5
RMS motor coil current per coil IrmsPer coilmax 2 A5
VBB Working current IVBBVBB=24V, T=25℃, CLK frequency=12MHztyp 7.8 · max 11 mA5
VBB Undervoltage protection VUVLOWhen VBB rise up; T=25℃typ 4.3 V5
VBB Undervoltage protection hysteresis VHYSVBB=24V, T=25℃typ 0.24 V5
Interface logic power supply IVIOVBB=24V, T=25℃typ 300 uA5
Interface power under voltage protect VuvioVBB=24V, T=25℃typ 2.5 V6
FLAG low VOLFLAG1, FLAG2; Iout= 2mA; VBB=24V, T=25℃max 0.5 V6
RDSON highside MOSFET RONVBB=24V,T=25°,Iout=0.5Atyp 0.2 Ω6
RDSON lowside MOSFET RONVBB=24V,T=25°,Iout=0.5Atyp 0.2 Ω6
Turn off leakage current IOFFOutput = 0; VBB=24V, T=25℃typ 200 uA6
Rise conversion time TLH24V,24Ω Resistive load,low20% to high80%; T=25℃typ 60 ns6
Descent transition time THL24V,24Ω Resistive load,high80%to low20%; T=25℃typ 60 ns6
Dead Time tDEADInternal parameters; VBB=24V, T=25℃min 100 ns6
Short circuit protection point IOCPdownShort circuit to Power when the lowside MOSFET is opened; VBB=24V, T=25℃typ 2 V6
Overcurrent detection time tDEGEffective duration of overcurrent detection; VBB=24V, T=25℃typ 2 us6
Over temperature protection point TTSDtemperature rise; VBB=24Vtyp 156 ℃6
Over temperature protection hysteresis TTSDthVBB=24Vtyp 26 ℃6
output voltage VvregWhen the load is 0mA; VBB=24V, T=25℃typ 5 V6
output voltage VvregWhen the load is 5mA; VBB=24V, T=25℃typ 4.95 V6
VREG Undervoltage protection VuvLDOVBB=24V, T=25℃typ 3.5 V6
VCP output frequency VvcpfrVCP oscillation frequency,FCLK=12MHz; VBB=24V, T=25℃typ 750 KHz7
Input frequency range FclkExternal clock input; VBB=24V, T=25℃min 4 · typ 12 · max 18 MHz7
Oscillation frequency rangeNo external input, use internal clock; VBB=24V, T=25℃min 11 · typ 12 · max 13 MHz7
Voltage range VREFREF Control current, linear control area; VBB=24V, T=25℃min 0.5 · max 2.5 V7

Pins, by the datasheet

28
1 OUT2B
Motor coil B output 2. · p. 2
2 ENABLE
High switches off the power stage and leaves all motor outputs floating. · p. 2
3 GND
GND. · p. 2
4 CP1
Charge pump capacitor output. · p. 2
5 CP2
Charge pump capacitor input; connect to CP1 through a 22nF 50V capacitor. · p. 2
6 VCP
Charge pump voltage; connect to VS through a 100nF capacitor. · p. 2
7 NC
Unused; leave open or connect to GND. · p. 2
8 VREG
Internal 5V regulator output; attach a nearby 2.2uF to 4.7uF ceramic capacitor to GND with the shortest possible loop to the GND pad. · p. 2
9 MS1
Microstep configuration with internal pull-down; MS2,MS1 select 00: 1/8, 01: 1/2, 10: 1/4, 11: 1/16. · p. 2
10 MS2
Microstep configuration with internal pull-down; MS2,MS1 select 00: 1/8, 01: 1/2, 10: 1/4, 11: 1/16. · p. 2
11 FLAG1
Diagnostic output high on driving error; reset by ENN=high. · p. 2
12 FLAG2
Configurable FLAG2 pulse output. · p. 2
13 CLK
12MHz clock input; connect to GND when using the internal clock. · p. 2
14 HOLDEN
Low enables automatic standstill current reduction; optional UART input/output, with power down disable available in UART mode. · p. 2
15 VIO
3.3V to 5V I/O supply for all digital pins. · p. 2
16 STEP
STEP input. · p. 3
17 REF
Analog reference voltage for current scaling. · p. 3
18 GND
GND. · p. 2
19 DIR
DIR input with internal pull-down resistor. · p. 3
20 NC
Unused; leave open or connect to GND. · p. 2
21 OUT1B
Motor coil B output 1. · p. 3
22 VBB1
Motor supply; provide nearby filtering capacitance with the shortest possible loop to the GND pad. · p. 3
23 SENSE1
Coil A sense resistor connection; place the resistor to GND nearby. · p. 3
24 OUT1A
Motor coil A output 1. · p. 3
25 PGND
GND. · p. 3
26 OUT2A
Motor coil A output 2. · p. 3
27 SENSE2
Coil B sense resistor connection; place the resistor to GND nearby. · p. 3
28 VBB1
Motor supply; provide nearby filtering capacitance with the shortest possible loop to the GND pad. · p. 3

Open-source boards using it

1
  • 2 layers38 × 44.6 mmServomotor3, the printed circuit board in 3D

    Servomotor3

    tomrodinger/servomotor

    Open-source NEMA-17 integrated servomotor (motor + closed-loop driver + controller + encoder). RS-485, Python/Arduino libraries, MCP server for AI control. Hardware, firmware and software.

    69 parts17MIT

Parts like it

1

Questions

Is there a KiCad symbol and footprint for the GC6609?

Yes. The symbol is EasyEDA_Cloud:GC6609_C16197208 and the footprint EasyEDA_Cloud:QFN-28_L5.0-W5.0-P0.50-BL-EP, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the GC6609?

QFN-28, with 29 pins. Its footprint is drawn on this page.

Where is the GC6609 datasheet?

SX-globalchip publishes it: the Datasheet link on this page opens it.

Where can I order the GC6609?

JLCPCB lists it as part C16197208, with 0 in stock; the sellers' links on this page open their listings.

What can replace the GC6609?

Parts like it in the library: the TMC2224-LA by TRINAMIC Motion Control GmbH. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the GC6609?

1 board in 1 repository on GitHub; the most starred are listed on this page, with their KiCad files.