Skip to the content
12345678910111213141516

VNH7100BAS

STMicroelectronicsExtended

-40℃~+150℃ 100mΩ 15A 1uA 4V~28V Interleaved conduction protection、Current sensing/regulation function Yes SO-16 Brushed DC Motor Drivers ROHS

Part id
st/VNH7100BAS
Category
Brushed DC Motor Drivers
Package
SO-16
Pins
16
In stock
0 at JLCPCB (C503078)
Used on
1 open-source board

Overview

The VNH7100BAS is a brushed DC Motor Driver made by STMicroelectronics in a SO-16 package with 16 pins. -40℃~+150℃ 100mΩ 15A 1uA 4V~28V Interleaved conduction protection、Current sensing/regulation function Yes SO-16 Brushed DC Motor Drivers ROHS.

PCBKit's library has its KiCad symbol (EasyEDA_Cloud:VNH7070BASTR, from EasyEDA) and its footprint (Package_SO:SO-16_3.9x9.9mm_P1.27mm, from KiCad's library), ready for a KiCad board. JLCPCB lists it (part C503078). 1 open-source board in 1 repository on GitHub use it.

Symbol

16GNDA15OUTA14SEL013CS12VCC11PWM10OUTB9GNDB8GNDB7OUTB6INB5VCC4VCC3INA2OUTA1GNDA
EasyEDA_Cloud:VNH7070BASTRFrom EasyEDA

Footprint

12345678910111213141516
Package_SO:SO-16_3.9x9.9mm_P1.27mmFrom KiCad's library

From the datasheet

12
Supply, least
4 V · VCC, minimum operating supply voltage · p. 9
Supply, most
28 V · VCC, maximum operating supply voltage · p. 9
Supply, absolute maximum
38 V · VCC, absolute maximum supply voltage · p. 7
Junction, hottest
150 °C · Maximum junction operating temperature · p. 8
Takes working
3.5 mA · VCC, typical on-state supply current; INA or INB = 5 V · p. 9
Takes at most
6 mA · VCC, maximum on-state supply current; INA or INB = 5 V · p. 9
Takes asleep
1 µA · VCC, maximum standby current at 25 °C, VCC = 13 V · p. 9
Takes asleep
3 µA · VCC, maximum standby current at 125 °C, VCC = 13 V · p. 9
Current limit
18 A · Typical high-side current limitation · p. 11
Junction to air (SO-16N)
40.7 K/W · Maximum HSD junction-ambient resistance, four-layer 2s2p PCB · p. 8
Junction to air (SO-16N)
55.4 K/W · Maximum LSD junction-ambient resistance, four-layer 2s2p PCB · p. 8
Edge
200 ns · Typical output fall time, VCC = 13 V, RLOAD = 5.2 Ω · p. 10

What it is and has

19
Qualification
AEC-Q100 qualified · p. 1
Output current
15 A · p. 1
Logic inputs
3 V CMOS-compatible · p. 1
Protection
Undervoltage shutdown · p. 1
Protection
Overvoltage clamp · p. 1
Protection
Thermal shutdown · p. 1
Protection
Cross-conduction protection · p. 1
Protection
Current and power limitation · p. 1
PWM
Operation up to 20 kHz · p. 1
MultiSense diagnostic
Analog motor current feedback · p. 1
MultiSense diagnostic
Output short to ground detection · p. 1
MultiSense diagnostic
Thermal shutdown indication · p. 1
MultiSense diagnostic
OFF-state open-load detection · p. 1
MultiSense diagnostic
Output short to VCC detection · p. 1
Operating mode
Standby Mode · p. 1
Operating mode
Half Bridge Operation · p. 1
Package
ECOPACK® · p. 1
Application
Automotive fully integrated H-bridge motor driver · p. 1
Package
SO-16N · p. 1

Specifications

247
ParameterConditionsAs printedPage
Supply voltage VCCmax 38 V7
Reverse DC Supply Voltage -VCCmax 0.3 V7
Reverse output current (continuous) IRmin -15 A7
Maximum transient supply voltage VCCPKISO 16750-2:2010 Test B clamped to 40 V; RL = 4 Ωmax 40 V7
Maximum jump start voltage for single pulse short circuit protection VCCJSmax 28 V7
Input current (INA and INB pins) IINmin -1 · max 10 mA7
SEL0 DC input current ISEL0min -1 · max 10 mA7
PWM input current IPWMmin -1 · max 10 mA7
CS pin DC output current ISENSEVGND = VCC and VSENSE < 0 Vmax 10 mA7
CS pin DC output current in reverse ISENSEVCC < 0 Vmin -20 mA7
Electrostatic discharge VESDHuman body model: R = 1.5 kΩ; C = 100 pF; INA, INB, PWMmax 2 kV8
Electrostatic discharge VESDHuman body model: R = 1.5 kΩ; C = 100 pF; SEL0max 2 kV8
Electrostatic discharge VESDHuman body model: R = 1.5 kΩ; C = 100 pF; CSmax 2 kV8
Electrostatic discharge VESDHuman body model: R = 1.5 kΩ; C = 100 pF; VCCmax 4 kV8
Electrostatic discharge VESDHuman body model: R = 1.5 kΩ; C = 100 pF; Outputmax 4 kV8
Charge device model (CDM-AEC-Q100-011) VESDmax 750 V8
Junction operating temperature Tcmin -40 · max 150 °C8
Storage temperature TSTGmin -55 · max 150 °C8
Thermal resistance junction-pin Rthj-pinHSDmax 32 °C/W8
Thermal resistance junction-pin Rthj-pinLSDmax 45 °C/W8
Thermal resistance junction-ambient (JEDEC JESD 51-2) Rthj-ambHSD; Device mounted on four-layers 2s2p PCBmax 40.7 °C/W8
Thermal resistance junction-ambient (JEDEC JESD 51-2) Rthj-ambLSD; Device mounted on four-layers 2s2p PCBmax 55.4 °C/W8
Operating supply voltage VCCmin 4 · max 28 V9
Supply current ISOff-state (standby); INA = INB = 0; SEL0 = 0; PWM = 0; Tj = 25 °C; VCC = 13 Vmax 1 uA9
Supply current ISOff-state (standby); INA = INB = 0; SEL0 = 0; PWM = 0; VCC = 13 V; Tj = 85°Cmax 1 uA9
Supply current ISOff-state (standby); INA = INB = 0; SEL0 = 0; PWM = 0; VCC = 13 V; Tj = 125 °Cmax 3 uA9
Supply current ISOff-state (no standby); INA = INB = 0; SEL0 = 5 V; PWM= 0typ 2 · max 4 mA9
Supply current ISOn-state: INA or INB = 5 V; PWM = 0 or PWM = 5; SEL0 = Xtyp 3.5 · max 6 mA9
Standby mode blanking time tD_STBYVCC = 13 V; INA = INB = PMW = 0 V; VSEL0 from 5 V to 0 Vmin 0.2 · typ 1 · max 1.8 ms9
Static high-side resistance RONHSIOUT = 2.5 A; Tj = 25°Ctyp 60 m9
Static high-side resistance RONHSIOUT = 2.5 A; Tj = -40 to 150°Cmax 120 m9
Static low-side resistance RONLSIOUT = 2.5 A; Tj = 25°Ctyp 40 m9
Static low-side resistance RONLSIOUT = 2.5 A; Tj = -40°C to 150°Cmax 80 m9
Free-wheeling diode forward voltage VfIOUT = -2.5 A; Tj = 150°Ctyp 0.7 · max 0.9 V9
Off-state output current of one leg IL(off)INA = INB = 0; PWM = 0; VCC = 13 V; Tj = 25 °Cmin 0 · max 0.5 uA9
Off-state output current of one leg IL(off)INA = INB = 0; PWM = 0; VCC = 13 V; Tj = 125 °Cmin 0 · max 3 uA9
Off-state output current of one leg with other HSD on IL(off_h)INA = 0; INB = 5 V; PWM = 0; VCC = 13 Vmin 20 · max 60 uA9
Input low level voltage VILVCC = 7 V up to 28 V; -40°C < Tj < 150°Cmax 0.9 V10
Input high level voltage VIHVCC = 7 V up to 28 V; -40°C < Tj < 150°Cmin 2.1 V10
Input hysteresis voltage VIHYSTVCC = 7 V up to 28 V; -40°C < Tj < 150°Cmin 0.2 V10
Input clamp voltage VICLIIN = 1 mA; VCC = 7 V up to 28 V; -40°C < Tj < 150°Cmin 5.3 · max 7.2 V10
Input clamp voltage VICLIIN = -1 mA; VCC = 7 V up to 28 V; -40°C < Tj < 150°Ctyp -0.7 V10
Input current IINLVIN = 0.9 V; VCC = 7 V up to 28 V; -40°C < Tj < 150°Cmin 1 uA10
Input current IINHVIN = 2.1 V; VCC = 7 V up to 28 V; -40°C < Tj < 150°Cmax 10 uA10
Input low level voltage VSELLSEL0; VCC = 7 V up to 18 V; -40°C < Tj < 150°Cmax 0.9 V10
Low level input current ISELLSEL0; VSEL = 0.9 V; VCC = 7 V up to 18 V; -40°C < Tj < 150°Cmin 1 uA10
Input high level voltage VSELHSEL0; VCC = 7 V up to 18 V; -40°C < Tj < 150°Cmin 2.1 V10
High level input current ISELHSEL0; VSEL = 2.1 V; VCC = 7 V up to 18 V; -40°C < Tj < 150°Cmax 10 uA10
Input hysteresis voltage VSEL(hyst)SEL0; VCC = 7 V up to 18 V; -40°C < Tj < 150°Cmin 0.2 V10
Input clamp voltage VSELCLSEL0; ISEL = 1 mA; VCC = 7 V up to 18 V; -40°C < Tj < 150°Cmin 5.3 · max 7.5 V10
Input clamp voltage VSELCLSEL0; ISEL = -1 mA; VCC = 7 V up to 18 V; -40°C < Tj < 150°Ctyp -0.8 V10
Input low level voltage VPWMPWM; VCC = 7 V up to 28 V; -40°C < Tj < 150°Cmax 0.9 V10
Low level input current IPWMPWM; VPWM = 0.9 V; VCC = 7 V up to 28 V; -40°C < Tj < 150°Cmin 1 uA10
Input high level voltage VPWMPWM; VCC = 7 V up to 28 V; -40°C < Tj < 150°Cmin 2.1 V10
High level input current IPWMHPWM; VPWM = 2.1 V; VCC = 7 V up to 28 V; -40°C < Tj < 150°Cmax 10 uA10
Input hysteresis voltage VPWM(hyst)PWM; VCC = 7 V up to 28 V; -40°C < Tj < 150°Cmin 0.2 V10
Input clamp voltage VPMWCLPWM; IPWM = 1 mA; VCC = 7 V up to 28 V; -40°C < Tj < 150°Cmin 5.3 · max 7.2 V10
Input clamp voltage VPMWCLPWM; IPWM = -1 mA; VCC = 7 V up to 28 V; -40°C < Tj < 150°Ctyp -0.7 V10
PWM frequency fVCC = 13 V; RLOAD = 5.2 Ω; guaranteed by design and characterizationmin 0 · max 20 kHz10
Turn-on delay time td(on)VCC = 13 V; RLOAD = 5.2 Ω; Input rise time < 1us (see Figure 6)typ 20 us10
Turn-off delay time td(off)VCC = 13 V; RLOAD = 5.2 Ω; Input rise time < 1us (see Figure 6)typ 13 us10
Rise time trVCC = 13 V; RLOAD = 5.2 Ω; See Figure 5typ 0.7 · max 1.5 us10
Fall time tfVCC = 13 V; RLOAD = 5.2 Ω; See Figure 5typ 0.2 · max 0.5 us10
Low-side turn-on delay time tcrossVCC = 13 V; RLOAD = 5.2 Ω; Input rise time < 1 us (see Figure 7)min 40 · typ 150 · max 350 us10
Undervoltage shutdown VUSDVCC = 7 V up to 18 V; -40°C < Tj < 150°Cmax 4 V11
Undervoltage shutdown reset VUSDresetVCC = 7 V up to 18 V; -40°C < Tj < 150°Cmax 5 V11
Undervolatge shutdown Hysteresis VUSDHystVCC = 7 V up to 18 V; -40°C < Tj < 150°Ctyp 0.4 V11
High-side current limitation ILIM_HVCC = 7 V up to 18 V; -40°C < Tj < 150°Cmin 12 · typ 18 · max 24 A11
Shutdown LS current ISD_LSVCC = 7 V up to 18 V; -40°C < Tj < 150°Cmin 14 · typ 22 · max 30 A11
Time to shutdown for the low-side tSD_LSVINA = VINB = 0 V; PWM = 5 V (see Figure 8); VCC = 7 V up to 18 V; -40°C < Tj < 150°Ctyp 5 us11
High-side clamp voltage (VCC to OUTA = 0 or OUTB = 0) VCL_HSDIOUT = 100 mA; tCLAMP = 1 ms; VCC = 7 V up to 18 V; -40°C < Tj < 150°Cmin 38 · typ 46 V11
Low-side clamp voltage (OUTA = VCC or OUTB = VCC to GND) VCL_LSDIOUT = 100 mA; tCLAMP = 1 ms; VCC = 7 V up to 18 V; -40°C < Tj < 150°Cmin 38 · typ 46 V11
High-side thermal shutdown temperature TTSD_HSINx = 2.1 V; VCC = 7 V up to 18 V; -40°C < Tj < 150°Cmin 150 · typ 175 · max 200 °C11
High-side thermal reset temperature TTR_HSVCC = 7 V up to 18 V; -40°C < Tj < 150°Cmin 135 °C11
High-side thermal hysteresis (TSD_HS - TR_HS) THYST_HSVCC = 7 V up to 18 V; -40°C < Tj < 150°Ctyp 7 °C11
Low-side thermal shutdown temperature TTSD_LSINx = 0 V; VCC = 7 V up to 18 V; -40°C < Tj < 150°Cmin 150 · typ 175 · max 200 °C11
Total clamp voltage (VCC to GND) VCLIOUT = 100 mA; tCLAMP = 1 ms; VCC = 7 V up to 18 V; -40°C < Tj < 150°Cmin 38 · typ 46 · max 52 V11
OFF-state open-load voltage detection threshold VOLINA = INB = 0; PWM = 0; VSEL0 = 5 V for CHA; VSEL0 = 0 V and within tD_STBY for CHB; VCC = 7 V up to 18 V; -40°C < Tj < 150°Cmin 2 · typ 3 · max 4 V11
OFF-state output sink current IL(off2)INA = INB = 0; VOUTx = VOL; PWM = 0 V; VSEL0 = 5 V for CHA; VSEL0 = 0 V and within tD_STBY for CHB; VCC = 7 V up to 18 V; -40°C < Tj < 150°Cmin -100 · max -15 uA11
OFF-state diagnostic delay time from falling edge of INPUT (see Figure 4) tDSTKONINA = 5 V to 0 V; INB = 0 V; VSEL0 = 5 V; IOUT = 0 A; VOUTA = 4 V; PWM = 0 V; VCC = 7 V up to 18 V; -40°C < Tj < 150°Cmin 40 · typ 150 · max 350 us11
OFF-state diagnostic delay time from rising edge of VOUT (see Figure 11) tD_VOLINA = INB = 0 V; PWM = 0 V; VOUTx = 0 V to 4 V; VSEL0 = 5 V for CHA; VSEL0 = 0 V and within tD_STBY for CHB; guaranteed by design and characterizationtyp 5 · max 30 us11
Input reset time for high-side fault unlatch (see Figure 9) tLatch_RST_HDVINx = 5 V to 0 V; HSDx faulting; VCC = 7 V up to 18 V; -40°C < Tj < 150°C; guaranteed by design and characterizationmin 3 · typ 10 · max 20 us12
Input reset time for low-side fault unlatch (see Figure 10) tLatch_RST_LSVINx = 0 V to 5 V; LSDx faulting; VCC = 7 V up to 18 V; -40°C < Tj < 150°C; guaranteed by design and characterizationmin 3 · typ 10 · max 20 us12
MultiSense clamp voltage VSENSE_CLVCC = 18 V; ISENSE = -5 mA; -40 °C < Tj < 150 °Ctyp 11 V12
MultiSense clamp voltage VSENSE_CLVCC = 18 V; ISENSE = 5 mA; -40 °C < Tj < 150 °Cmin -13 · max -9 V12
IOUT/ISENSE K0IOUT = 0.05 A; VSENSE = 0.5 V; Tj = -40°C to 150°C; 7 V < VCC < 18 Vmin 53612
IOUT/ISENSE K1IOUT = 0.2 A; VSENSE = 0.5 V; Tj = -40°C to 150°C; 7 V < VCC < 18 Vmin 710 · typ 1190 · max 167012
IOUT/ISENSE K2IOUT = 2.5 A; VSENSE = 4 V; Tj = -40°C to 150°C; 7 V < VCC < 18 Vmin 1015 · typ 1120 · max 122912
IOUT/ISENSE K3IOUT = 4 A; VSENSE = 4 V; Tj = -40°C to 150°C; 7 V < VCC < 18 Vmin 1040 · typ 1120 · max 120012
Analog sense current drift dK0/K0IOUT = 0.05 A; VSENSE = 0.5 V; Tj = -40°C to 150°C; 7 V < VCC < 18 Vmin -25 · max 25 %12
Analog sense current drift dK1/K1IOUT = 0.2 A; VSENSE = 0.5 V; Tj = -40°C to 150°C; 7 V < VCC < 18 Vmin -21 · max 21 %12
Analog sense current drift dK2/K2IOUT = 2.5 A; VSENSE = 4 V; Tj = -40°C to 150°C; 7 V < VCC < 18 Vmin -5 · max 5 %12
Analog sense current drift dK3/K3IOUT = 4 A; VSENSE = 4 V; Tj = -40°C to 150°C; 7 V < VCC < 18 Vmin -4 · max 4 %12
Max analog sense output voltage VSENSE_SATVCC = 7 V; RSENSE = 10 kΩ; VSEL0 = 5 V; IOUTA = 4 A; VINA = 5 V; PWM = 0; Tj = 150 °Cmin 5 V12
MultiSense leakage current ISENSE0IOUT = 0 A; VSENSE = 0 V; INx = 0 V; SEL0 = 0; Tj = -40°C to 150°C (standby); 7 V < VCC < 18 Vmin 0 · max 0.5 uA12
MultiSense leakage current ISENSE0IOUT = 0 A; VSENSE = 0 V; INx = 0 V; SEL0 = 5 V; Tj = -40°C to 150°C (no standby); 7 V < VCC < 18 Vmin 0 · max 0.5 uA12
MultiSense leakage current ISENSE0INx = 5 V; PWM = 5 V; Tj = -40°C to 150°C; IOUT = 0 A; 7 V < VCC < 18 Vmin 0 · max 5 uA12
R1 R12Layer PCB, FPtyp 5.3 °C/W31
R1 R12Layer PCB, Area/island = 2 cm2typ 5.3 °C/W31
R1 R12Layer PCB, Area/island = 8 cm2typ 5.3 °C/W31
R1 R14Layer PCBtyp 5.3 °C/W31
R2 R22Layer PCB, FPtyp 12 °C/W31
R2 R22Layer PCB, Area/island = 2 cm2typ 12 °C/W31
R2 R22Layer PCB, Area/island = 8 cm2typ 12 °C/W31
R2 R24Layer PCBtyp 12 °C/W31
R3 R32Layer PCB, FPtyp 30 °C/W31
R3 R32Layer PCB, Area/island = 2 cm2typ 25 °C/W31
R3 R32Layer PCB, Area/island = 8 cm2typ 25 °C/W31
R3 R34Layer PCBtyp 30 °C/W31
R4 R42Layer PCB, FPtyp 42 °C/W31
R4 R42Layer PCB, Area/island = 2 cm2typ 12 °C/W31
R4 R42Layer PCB, Area/island = 8 cm2typ 12 °C/W31
R4 R44Layer PCBtyp 2 °C/W31
R5 R52Layer PCB, FPtyp 85 °C/W31
R5 R52Layer PCB, Area/island = 2 cm2typ 45 °C/W31
R5 R52Layer PCB, Area/island = 8 cm2typ 30 °C/W31
R5 R54Layer PCBtyp 17 °C/W31
R6 R62Layer PCB, FPtyp 5.3 °C/W31
R6 R62Layer PCB, Area/island = 2 cm2typ 5.3 °C/W31
R6 R62Layer PCB, Area/island = 8 cm2typ 5.3 °C/W31
R6 R64Layer PCBtyp 5.3 °C/W31
R7 R72Layer PCB, FPtyp 6.3 °C/W31
R7 R72Layer PCB, Area/island = 2 cm2typ 6.3 °C/W31
R7 R72Layer PCB, Area/island = 8 cm2typ 6.3 °C/W31
R7 R74Layer PCBtyp 6.3 °C/W31
R8 R82Layer PCB, FPtyp 12 °C/W31
R8 R82Layer PCB, Area/island = 2 cm2typ 12 °C/W31
R8 R82Layer PCB, Area/island = 8 cm2typ 12 °C/W31
R8 R84Layer PCBtyp 12 °C/W31
R9 R92Layer PCB, FPtyp 30 °C/W31
R9 R92Layer PCB, Area/island = 2 cm2typ 30 °C/W31
R9 R92Layer PCB, Area/island = 8 cm2typ 30 °C/W31
R9 R94Layer PCBtyp 42 °C/W31
R10 R102Layer PCB, FPtyp 68 °C/W31
R10 R102Layer PCB, Area/island = 2 cm2typ 52 °C/W31
R10 R102Layer PCB, Area/island = 8 cm2typ 48 °C/W31
R10 R104Layer PCBtyp 10 °C/W31
R11 R112Layer PCB, FPtyp 75 °C/W31
R11 R112Layer PCB, Area/island = 2 cm2typ 80 °C/W31
R11 R112Layer PCB, Area/island = 8 cm2typ 60 °C/W31
R11 R114Layer PCBtyp 26 °C/W31
R12 R122Layer PCB, FPtyp 6.3 °C/W31
R12 R122Layer PCB, Area/island = 2 cm2typ 6.3 °C/W31
R12 R122Layer PCB, Area/island = 8 cm2typ 6.3 °C/W31
R12 R124Layer PCBtyp 6.3 °C/W31
R13 R132Layer PCB, FPtyp 12 °C/W31
R13 R132Layer PCB, Area/island = 2 cm2typ 12 °C/W31
R13 R132Layer PCB, Area/island = 8 cm2typ 12 °C/W31
R13 R134Layer PCBtyp 12 °C/W31
R14 R142Layer PCB, FPtyp 30 °C/W31
R14 R142Layer PCB, Area/island = 2 cm2typ 30 °C/W31
R14 R142Layer PCB, Area/island = 8 cm2typ 30 °C/W31
R14 R144Layer PCBtyp 42 °C/W31
R15 R152Layer PCB, FPtyp 68 °C/W31
R15 R152Layer PCB, Area/island = 2 cm2typ 52 °C/W31
R15 R152Layer PCB, Area/island = 8 cm2typ 48 °C/W31
R15 R154Layer PCBtyp 10 °C/W31
R16 R162Layer PCB, FPtyp 75 °C/W31
R16 R162Layer PCB, Area/island = 2 cm2typ 80 °C/W31
R16 R162Layer PCB, Area/island = 8 cm2typ 60 °C/W31
R16 R164Layer PCBtyp 26 °C/W31
R17 R172Layer PCB, FPtyp 120 °C/W31
R17 R172Layer PCB, Area/island = 2 cm2typ 100 °C/W31
R17 R172Layer PCB, Area/island = 8 cm2typ 100 °C/W31
R17 R174Layer PCBtyp 100 °C/W31
R18 R182Layer PCB, FPtyp 120 °C/W31
R18 R182Layer PCB, Area/island = 2 cm2typ 100 °C/W31
R18 R182Layer PCB, Area/island = 8 cm2typ 100 °C/W31
R18 R184Layer PCBtyp 100 °C/W31
R19 R192Layer PCB, FPtyp 180 °C/W32
R19 R192Layer PCB, Area/island = 2 cm2typ 170 °C/W32
R19 R192Layer PCB, Area/island = 8 cm2typ 170 °C/W32
R19 R194Layer PCBtyp 170 °C/W32
R20 R202Layer PCB, FPtyp 180 °C/W32
R20 R202Layer PCB, Area/island = 2 cm2typ 170 °C/W32
R20 R202Layer PCB, Area/island = 8 cm2typ 170 °C/W32
R20 R204Layer PCBtyp 170 °C/W32
C1 C12Layer PCB, FPtyp 0.00065 W·s/°C32
C1 C12Layer PCB, Area/island = 2 cm2typ 0.00065 W·s/°C32
C1 C12Layer PCB, Area/island = 8 cm2typ 0.00065 W·s/°C32
C1 C14Layer PCBtyp 0.00065 W·s/°C32
C2 C22Layer PCB, FPtyp 0.018 W·s/°C32
C2 C22Layer PCB, Area/island = 2 cm2typ 0.018 W·s/°C32
C2 C22Layer PCB, Area/island = 8 cm2typ 0.018 W·s/°C32
C2 C24Layer PCBtyp 0.018 W·s/°C32
C3 C32Layer PCB, FPtyp 0.08 W·s/°C32
C3 C32Layer PCB, Area/island = 2 cm2typ 0.1 W·s/°C32
C3 C32Layer PCB, Area/island = 8 cm2typ 0.1 W·s/°C32
C3 C34Layer PCBtyp 0.1 W·s/°C32
C4 C42Layer PCB, FPtyp 0.2 W·s/°C32
C4 C42Layer PCB, Area/island = 2 cm2typ 0.5 W·s/°C32
C4 C42Layer PCB, Area/island = 8 cm2typ 1 W·s/°C32
C4 C44Layer PCBtyp 2 W·s/°C32
C5 C52Layer PCB, FPtyp 1.5 W·s/°C32
C5 C52Layer PCB, Area/island = 2 cm2typ 2 W·s/°C32
C5 C52Layer PCB, Area/island = 8 cm2typ 6 W·s/°C32
C5 C54Layer PCBtyp 12 W·s/°C32
C6 C62Layer PCB, FPtyp 0.00065 W·s/°C32
C6 C62Layer PCB, Area/island = 2 cm2typ 0.00065 W·s/°C32
C6 C62Layer PCB, Area/island = 8 cm2typ 0.00065 W·s/°C32
C6 C64Layer PCBtyp 0.00065 W·s/°C32
C7 C72Layer PCB, FPtyp 0.0005 W·s/°C32
C7 C72Layer PCB, Area/island = 2 cm2typ 0.0005 W·s/°C32
C7 C72Layer PCB, Area/island = 8 cm2typ 0.0005 W·s/°C32
C7 C74Layer PCBtyp 0.0005 W·s/°C32
C8 C82Layer PCB, FPtyp 0.018 W·s/°C32
C8 C82Layer PCB, Area/island = 2 cm2typ 0.018 W·s/°C32
C8 C82Layer PCB, Area/island = 8 cm2typ 0.018 W·s/°C32
C8 C84Layer PCBtyp 0.018 W·s/°C32
C9 C92Layer PCB, FPtyp 0.06 W·s/°C32
C9 C92Layer PCB, Area/island = 2 cm2typ 0.06 W·s/°C32
C9 C92Layer PCB, Area/island = 8 cm2typ 0.06 W·s/°C32
C9 C94Layer PCBtyp 0.06 W·s/°C32
C10 C102Layer PCB, FPtyp 0.08 W·s/°C32
C10 C102Layer PCB, Area/island = 2 cm2typ 0.1 W·s/°C32
C10 C102Layer PCB, Area/island = 8 cm2typ 0.2 W·s/°C32
C10 C104Layer PCBtyp 0.5 W·s/°C32
C11 C112Layer PCB, FPtyp 1 W·s/°C32
C11 C112Layer PCB, Area/island = 2 cm2typ 2.5 W·s/°C32
C11 C112Layer PCB, Area/island = 8 cm2typ 3 W·s/°C32
C11 C114Layer PCBtyp 6 W·s/°C32
C12 C122Layer PCB, FPtyp 0.0005 W·s/°C32
C12 C122Layer PCB, Area/island = 2 cm2typ 0.0005 W·s/°C32
C12 C122Layer PCB, Area/island = 8 cm2typ 0.0005 W·s/°C32
C12 C124Layer PCBtyp 0.0005 W·s/°C32
C13 C132Layer PCB, FPtyp 0.018 W·s/°C32
C13 C132Layer PCB, Area/island = 2 cm2typ 0.018 W·s/°C32
C13 C132Layer PCB, Area/island = 8 cm2typ 0.018 W·s/°C32
C13 C134Layer PCBtyp 0.018 W·s/°C32
C14 C142Layer PCB, FPtyp 0.06 W·s/°C32
C14 C142Layer PCB, Area/island = 2 cm2typ 0.06 W·s/°C32
C14 C142Layer PCB, Area/island = 8 cm2typ 0.06 W·s/°C32
C14 C144Layer PCBtyp 0.06 W·s/°C32
C15 C152Layer PCB, FPtyp 0.08 W·s/°C32
C15 C152Layer PCB, Area/island = 2 cm2typ 0.1 W·s/°C32
C15 C152Layer PCB, Area/island = 8 cm2typ 0.2 W·s/°C32
C15 C154Layer PCBtyp 0.5 W·s/°C32
C16 C162Layer PCB, FPtyp 1 W·s/°C32
C16 C162Layer PCB, Area/island = 2 cm2typ 2.5 W·s/°C32
C16 C162Layer PCB, Area/island = 8 cm2typ 3 W·s/°C32
C16 C164Layer PCBtyp 6 W·s/°C32
Test pulse 1, peak amplitude USLevel III, Status II; 500 pulses; minimum repetition time 0,5 s; pulse duration 2ms; generator impedance 10 Ωtyp -112 V24
Test pulse 2a, peak amplitude USLevel III, Status II; 500 pulses; repetition time 0,2 s to 5s; pulse duration 50us; generator impedance 2 Ωtyp 55 V24
Test pulse 3a, peak amplitude USLevel IV, Status II; test time 1h; burst cycle 90 ms to 100 ms; pulse duration 0.1us; generator impedance 50 Ωtyp -220 V24
Test pulse 3b, peak amplitude USLevel IV, Status II; test time 1h; burst cycle 90 ms to 100 ms; pulse duration 0.1us; generator impedance 50 Ωtyp 150 V24
Test pulse 4, peak amplitude USLevel IV, Status II; 1 pulse; pulse duration 100mstyp -7 V24
Load dump Test B USISO 16750-2:2010; 5 pulse; minimum repetition time 1 min; pulse duration 400 ms; generator impedance 2 Ωtyp 40 V24

Pins, by the datasheet

16
1 GNDA
Source of low-side switch A. · p. 6
2 OUTA
Source of high-side switch A / drain of low-side switch A. · p. 6
3 INA
Clockwise input. · p. 6
4 VCC
Power supply voltage. · p. 6
5 VCC
Power supply voltage. · p. 6
6 INB
Counter clockwise input. · p. 6
7 OUTB
Source of high-side switch B / drain of low-side switch B. · p. 6
8 GNDB
Source of low-side switch B. · p. 6
9 GNDB
Source of low-side switch B. · p. 6
10 OUTB
Source of high-side switch B / drain of low-side switch B. · p. 6
11 PWM
Active-high CMOS-compatible input with hysteresis; modulates low-side FET gates for motor speed control. · p. 6
12 VCC
Power supply voltage. · p. 6
13 CS
Multiplexed analog sense output delivering a current proportional to motor current. · p. 6
14 SEL0
Active-high input compatible with 3 V and 5 V CMOS; selects CurrentSense information together with INA and INB. · p. 6
15 OUTA
Source of high-side switch A / drain of low-side switch A. · p. 6
16 GNDA
Source of low-side switch A. · p. 6

Ordering codes, by the datasheet

1
VNH7100BASTR
SO-16N · Tape and reel · p. 1

Open-source boards using it

1

Questions

Is there a KiCad symbol and footprint for the VNH7100BAS?

Yes. The symbol is EasyEDA_Cloud:VNH7070BASTR and the footprint Package_SO:SO-16_3.9x9.9mm_P1.27mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the VNH7100BAS?

SO-16, with 16 pins. Its footprint is drawn on this page.

Where is the VNH7100BAS datasheet?

STMicroelectronics publishes it: the Datasheet link on this page opens it.

Where can I order the VNH7100BAS?

JLCPCB lists it as part C503078, with 0 in stock; the sellers' links on this page open their listings.

Which open-source boards use the VNH7100BAS?

1 board in 1 repository on GitHub; the most starred are listed on this page, with their KiCad files.