
FRDM MCXx Shield V1.3
EmielV2002/FRDM_MCXx_SensHat
A hat with sensors and actuators for the FRDM-MCXA153 and FRDM-MCXN947 development boards made by NXP.
STMicroelectronicsExtended
-40℃~+85℃ 1.8V~5.5V 1Kbit 200 Years 20MHz 4,000,000 Cycles 5ms Hardware write protection function、Software write protection function、Built-in power-on reset (POR)、Built-in write enable latch (WEL) SPI SO-8 EEPROM ROHS
The M95010-RMN6TP is an EEPROM made by STMicroelectronics in a SO-8 package with 8 pins. -40℃~+85℃ 1.8V~5.5V 1Kbit 200 Years 20MHz 4,000,000 Cycles 5ms Hardware write protection function、Software write protection function、Built-in power-on reset (POR)、Built-in write enable latch (WEL) SPI SO-8 EEPROM ROHS.
PCBKit's library has its KiCad symbol (EasyEDA_Cloud:M25P40-VMN6PBA, from EasyEDA) and its footprint (Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, from KiCad's library), ready for a KiCad board. 1,585 are in stock at JLCPCB (part C2061643). 2 open-source boards in 1 repository on GitHub use it.
| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Ambient operating temperature TAMR | min -40 · max 130 °C | 30 | |
| Storage temperature TSTG | min -65 · max 150 °C | 30 | |
| Output voltage VO | Maximum VCC+0.6 V | min -0.5 V | 30 |
| Input voltage VI | Maximum VCC+1.0 V | min -0.5 V | 30 |
| DC output current (Q = 0) IOL | Q = 0 | max 5 mA | 30 |
| DC output current (Q = 1) IIH | Q = 1 | max 5 mA | 30 |
| Supply voltage VCC | min -0.5 · max 6.5 V | 30 | |
| Electrostatic pulse (Human Body Model) voltage VESD | Positive and negative pulses on pin pairs; AEC-Q100-002, compliant with JESD22-A114. | max 4000 V | 30 |
| Supply voltage VCC | M95010-R | min 1.8 · max 5.5 V | 31 |
| Ambient operating temperature TA | M95010-R | min -40 · max 85 °C | 31 |
| Input rise and fall times | max 50 ns | 31 | |
| Input leakage current ILI | M95010-R at 2.5 V ≤ VCC ≤ 5.5 V; VIN = VSS or VCC; ±2 uA maximum magnitude. | max 2 uA | 33 |
| Output leakage current ILO | M95010-R at 2.5 V ≤ VCC ≤ 5.5 V; S = VCC, VOUT = VSS or VCC; ±2 uA maximum magnitude. | max 2 uA | 33 |
| Supply current (Read) ICC | M95010-R; VCC = 2.5 V, fC = 5 MHz, C = 0.1 VCC/0.9 VCC, Q = open. | max 2 mA | 33 |
| Supply current (Read) ICC | M95010-R; VCC = 2.5 V, fC = 10 MHz, C = 0.1 VCC/0.9 VCC, Q = open. | max 2 mA | 33 |
| Supply current (Read) ICC | M95010-R, process letter K only; VCC = 5.5 V, fC = 20 MHz, C = 0.1 VCC/0.9 VCC, Q = open. | max 5 mA | 33 |
| Supply current (Write) ICC0 | M95010-R; during tW, S = VCC, 2.5 V < VCC < 5.5 V; characterized only. | max 5 mA | 33 |
| Supply current (Standby) ICC1 | M95010-R; S = VCC, VCC = 5.5 V, VIN = VSS or VCC; note (3): 2 uA for process letter G or S. | max 3 uA | 33 |
| Supply current (Standby) ICC1 | M95010-R; S = VCC, VCC = 2.5 V, VIN = VSS or VCC; note (4): 1 uA for process letter G or S. | max 2 uA | 33 |
| Input low voltage VIL | M95010-R at 2.5 V ≤ VCC ≤ 5.5 V; maximum 0.3 VCC. | min -0.45 V | 33 |
| Output low voltage VOL | M95010-R; IOL = 1.5 mA, VCC = 2.5 V. | max 0.4 V | 33 |
| Internal reset threshold voltage VRES | M95010-R at 2.5 V ≤ VCC ≤ 5.5 V; characterized only. Process letter K: minimum 0.5 V, maximum 1.5 V. | min 1 · max 1.65 V | 33 |
| Input leakage current ILI | M95010-R; VIN = VSS or VCC; ±2 uA maximum magnitude. | max 2 uA | 34 |
| Output leakage current ILO | M95010-R; S = VCC, voltage applied on Q = VSS or VCC; ±2 uA maximum magnitude. | max 2 uA | 34 |
| Supply current (Read) ICC | M95010-R; VCC = 1.8 V, fC = 5 MHz, C = 0.1 VCC/0.9 VCC, Q = open. | max 2 mA | 34 |
| Supply current (Write) ICC0 | M95010-R; VCC = 1.8 V, during tW, S = VCC; characterized only. | max 5 mA | 34 |
| Supply current (Standby) ICC1 | M95010-R; VCC = 1.8 V, S = VCC, VIN = VSS or VCC. | max 1 uA | 34 |
| Input low voltage VIL | M95010-R; VCC < 2.5 V; maximum 0.25 VCC. | min -0.45 V | 34 |
| Output low voltage VOL | M95010-R; IOL = 0.15 mA, VCC = 1.8 V. | max 0.3 V | 34 |
| Internal reset threshold voltage VRES | M95010-R; characterized only. Process letter K: minimum 0.5 V, maximum 1.5 V. | min 1 · max 1.65 V | 34 |
| Clock frequency fC | M95010-R; VCC = 2.5 to 5.5 V; minimum D.C. | max 10 MHz | 35 |
| Clock frequency fC | M95010-R, process letter K only; VCC = 4.5 to 5.5 V; minimum D.C. | max 20 MHz | 35 |
| S active setup time tSLCH | M95010-R; VCC = 2.5 to 5.5 V | min 30 ns | 35 |
| S active setup time tSLCH | M95010-R, process letter K only; VCC = 4.5 to 5.5 V | min 15 ns | 35 |
| S not active setup time tSHCH | M95010-R; VCC = 2.5 to 5.5 V | min 30 ns | 35 |
| S not active setup time tSHCH | M95010-R, process letter K only; VCC = 4.5 to 5.5 V | min 15 ns | 35 |
| S deselect time tSHSL | M95010-R; VCC = 2.5 to 5.5 V | min 40 ns | 35 |
| S deselect time tSHSL | M95010-R, process letter K only; VCC = 4.5 to 5.5 V | min 20 ns | 35 |
| S active hold time tCHSH | M95010-R; VCC = 2.5 to 5.5 V | min 30 ns | 35 |
| S active hold time tCHSH | M95010-R, process letter K only; VCC = 4.5 to 5.5 V | min 15 ns | 35 |
| S not active hold time tCHSL | M95010-R; VCC = 2.5 to 5.5 V | min 30 ns | 35 |
| S not active hold time tCHSL | M95010-R, process letter K only; VCC = 4.5 to 5.5 V | min 15 ns | 35 |
| Clock high time tCH | M95010-R; VCC = 2.5 to 5.5 V; tCH + tCL ≥ 1/fC(max). | min 40 ns | 35 |
| Clock high time tCH | M95010-R, process letter K only; VCC = 4.5 to 5.5 V; tCH + tCL ≥ 1/fC(max). | min 20 ns | 35 |
| Clock low time tCL | M95010-R; VCC = 2.5 to 5.5 V; tCH + tCL ≥ 1/fC(max). | min 40 ns | 35 |
| Clock low time tCL | M95010-R, process letter K only; VCC = 4.5 to 5.5 V; tCH + tCL ≥ 1/fC(max). | min 20 ns | 35 |
| Clock rise time tCLCH | M95010-R; VCC = 2.5 to 5.5 V; characterized only. | max 2 us | 35 |
| Clock rise time tCLCH | M95010-R, process letter K only; VCC = 4.5 to 5.5 V; characterized only. | max 2 us | 35 |
| Clock fall time tCHCL | M95010-R; VCC = 2.5 to 5.5 V; characterized only. | max 2 us | 35 |
| Clock fall time tCHCL | M95010-R, process letter K only; VCC = 4.5 to 5.5 V; characterized only. | max 2 us | 35 |
| Data in setup time tDVCH | M95010-R; VCC = 2.5 to 5.5 V | min 10 ns | 35 |
| Data in setup time tDVCH | M95010-R, process letter K only; VCC = 4.5 to 5.5 V | min 5 ns | 35 |
| Data in hold time tCHDX | M95010-R; VCC = 2.5 to 5.5 V | min 10 ns | 35 |
| Data in hold time tCHDX | M95010-R, process letter K only; VCC = 4.5 to 5.5 V | min 10 ns | 35 |
| Clock low hold time after HOLD not active tHHCH | M95010-R; VCC = 2.5 to 5.5 V | min 30 ns | 35 |
| Clock low hold time after HOLD not active tHHCH | M95010-R, process letter K only; VCC = 4.5 to 5.5 V | min 15 ns | 35 |
| Clock low hold time after HOLD active tHLCH | M95010-R; VCC = 2.5 to 5.5 V | min 30 ns | 35 |
| Clock low hold time after HOLD active tHLCH | M95010-R, process letter K only; VCC = 4.5 to 5.5 V | min 15 ns | 35 |
| Clock low set-up time before HOLD active tCLHL | M95010-R; VCC = 2.5 to 5.5 V | min 0 ns | 35 |
| Clock low set-up time before HOLD active tCLHL | M95010-R, process letter K only; VCC = 4.5 to 5.5 V | min 0 ns | 35 |
| Clock low set-up time before HOLD not active tCLHH | M95010-R; VCC = 2.5 to 5.5 V | min 0 ns | 35 |
| Clock low set-up time before HOLD not active tCLHH | M95010-R, process letter K only; VCC = 4.5 to 5.5 V | min 0 ns | 35 |
| Output disable time tSHQZ | M95010-R; VCC = 2.5 to 5.5 V; characterized only. | max 40 ns | 35 |
| Output disable time tSHQZ | M95010-R, process letter K only; VCC = 4.5 to 5.5 V; characterized only. | max 20 ns | 35 |
| Clock low to output valid tCLQV | M95010-R; VCC = 2.5 to 5.5 V; tCL must accommodate tCLQV plus master Read setup time. | max 40 ns | 35 |
| Clock low to output valid tCLQV | M95010-R, process letter K only; VCC = 4.5 to 5.5 V; tCL must accommodate tCLQV plus master Read setup time. | max 20 ns | 35 |
| Output hold time tCLQX | M95010-R; VCC = 2.5 to 5.5 V | min 0 ns | 35 |
| Output hold time tCLQX | M95010-R, process letter K only; VCC = 4.5 to 5.5 V | min 0 ns | 35 |
| Output rise time tQLQH | M95010-R; VCC = 2.5 to 5.5 V; characterized only. | max 40 ns | 35 |
| Output rise time tQLQH | M95010-R, process letter K only; VCC = 4.5 to 5.5 V; characterized only. | max 20 ns | 35 |
| Output fall time tQHQL | M95010-R; VCC = 2.5 to 5.5 V; characterized only. | max 40 ns | 35 |
| Output fall time tQHQL | M95010-R, process letter K only; VCC = 4.5 to 5.5 V; characterized only. | max 20 ns | 35 |
| HOLD high to output valid tHHQV | M95010-R; VCC = 2.5 to 5.5 V | max 40 ns | 35 |
| HOLD high to output valid tHHQV | M95010-R, process letter K only; VCC = 4.5 to 5.5 V | max 20 ns | 35 |
| HOLD low to output high-Z tHLQZ | M95010-R; VCC = 2.5 to 5.5 V; characterized only. | max 40 ns | 35 |
| HOLD low to output high-Z tHLQZ | M95010-R, process letter K only; VCC = 4.5 to 5.5 V; characterized only. | max 20 ns | 35 |
| Write time tW | M95010-R; VCC = 2.5 to 5.5 V | max 5 ms | 35 |
| Write time tW | M95010-R, process letter K only; VCC = 4.5 to 5.5 V | max 5 ms | 35 |
| Clock frequency fC | M95010-R; Table 10 and Table 12 conditions; minimum D.C.; at VCC ≥ 2.5 V refer to Table 18. | max 5 MHz | 36 |
| S active setup time tSLCH | M95010-R; Table 10 and Table 12 conditions; at VCC ≥ 2.5 V refer to Table 18. | min 60 ns | 36 |
| S not active setup time tSHCH | M95010-R; Table 10 and Table 12 conditions; at VCC ≥ 2.5 V refer to Table 18. | min 60 ns | 36 |
| S deselect time tSHSL | M95010-R; Table 10 and Table 12 conditions; at VCC ≥ 2.5 V refer to Table 18. | min 90 ns | 36 |
| S active hold time tCHSH | M95010-R; Table 10 and Table 12 conditions; at VCC ≥ 2.5 V refer to Table 18. | min 60 ns | 36 |
| S not active hold time tCHSL | M95010-R; Table 10 and Table 12 conditions; at VCC ≥ 2.5 V refer to Table 18. | min 60 ns | 36 |
| Clock high time tCH | M95010-R; below 2.5 V; tCH + tCL ≥ 1/fC(max). | min 80 ns | 36 |
| Clock low time tCL | M95010-R; below 2.5 V; tCH + tCL ≥ 1/fC(max). | min 80 ns | 36 |
| Clock rise time tCLCH | M95010-R; below 2.5 V; characterized only. | max 2 us | 36 |
| Clock fall time tCHCL | M95010-R; below 2.5 V; characterized only. | max 2 us | 36 |
| Data in setup time tDVCH | M95010-R; below 2.5 V | min 20 ns | 36 |
| Data in hold time tCHDX | M95010-R; below 2.5 V | min 20 ns | 36 |
| Clock low hold time after HOLD not active tHHCH | M95010-R; below 2.5 V | min 60 ns | 36 |
| Clock low hold time after HOLD active tHLCH | M95010-R; below 2.5 V | min 60 ns | 36 |
| Clock low set-up time before HOLD active tCLHL | M95010-R; below 2.5 V | min 0 ns | 36 |
| Clock low set-up time before HOLD not active tCLHH | M95010-R; below 2.5 V | min 0 ns | 36 |
| Output disable time tSHQZ | M95010-R; below 2.5 V; characterized only. | max 80 ns | 36 |
| Clock low to output valid tCLQV | M95010-R; below 2.5 V | max 80 ns | 36 |
| Output hold time tCLQX | M95010-R; below 2.5 V | min 0 ns | 36 |
| Output rise time tQLQH | M95010-R; below 2.5 V; characterized only. | max 80 ns | 36 |
| Output fall time tQHQL | M95010-R; below 2.5 V; characterized only. | max 80 ns | 36 |
| HOLD high to output valid tHHQV | M95010-R; below 2.5 V | max 80 ns | 36 |
| HOLD low to output high-Z tHLQZ | M95010-R; below 2.5 V; characterized only. | max 80 ns | 36 |
| Write time tW | M95010-R; below 2.5 V | max 5 ms | 36 |
| Clock frequency fC | M95010-R at VCC = 2.5 or 5.0 V, per Table 21 note (2); not recommended for new designs; minimum D.C. | max 10 MHz | 37 |
| S active setup time tSLCH | M95010-R at VCC = 2.5 or 5.0 V; not recommended for new designs. | min 15 ns | 37 |
| S not active setup time tSHCH | M95010-R at VCC = 2.5 or 5.0 V; not recommended for new designs. | min 15 ns | 37 |
| S deselect time tSHSL | M95010-R at VCC = 2.5 or 5.0 V; not recommended for new designs. | min 40 ns | 37 |
| S active hold time tCHSH | M95010-R at VCC = 2.5 or 5.0 V; not recommended for new designs. | min 25 ns | 37 |
| S not active hold time tCHSL | M95010-R at VCC = 2.5 or 5.0 V; not recommended for new designs. | min 15 ns | 37 |
| Clock high time tCH | M95010-R at VCC = 2.5 or 5.0 V; not recommended for new designs; tCH + tCL ≥ 1/fC(max). | min 40 ns | 37 |
| Clock low time tCL | M95010-R at VCC = 2.5 or 5.0 V; not recommended for new designs; tCH + tCL ≥ 1/fC(max). | min 40 ns | 37 |
| Clock rise time tCLCH | M95010-R at VCC = 2.5 or 5.0 V; not recommended for new designs; guaranteed by characterization. | max 1 us | 37 |
| Clock fall time tCHCL | M95010-R at VCC = 2.5 or 5.0 V; not recommended for new designs; guaranteed by characterization. | max 1 us | 37 |
| Data in setup time tDVCH | M95010-R at VCC = 2.5 or 5.0 V; not recommended for new designs. | min 15 ns | 37 |
| Data in hold time tCHDX | M95010-R at VCC = 2.5 or 5.0 V; not recommended for new designs. | min 15 ns | 37 |
| Clock low hold time after HOLD not active tHHCH | M95010-R at VCC = 2.5 or 5.0 V; not recommended for new designs. | min 15 ns | 37 |
| Clock low hold time after HOLD active tHLCH | M95010-R at VCC = 2.5 or 5.0 V; not recommended for new designs. | min 20 ns | 37 |
| Clock low setup time before HOLD active tCLHL | M95010-R at VCC = 2.5 or 5.0 V; not recommended for new designs. | min 0 ns | 37 |
| Clock low setup time before HOLD not active tCLHH | M95010-R at VCC = 2.5 or 5.0 V; not recommended for new designs. | min 0 ns | 37 |
| Output disable time tSHQZ | M95010-R at VCC = 2.5 or 5.0 V; not recommended for new designs; guaranteed by characterization. | max 25 ns | 37 |
| Clock low to output valid tCLQV | M95010-R at VCC = 2.5 or 5.0 V; not recommended for new designs. | max 35 ns | 37 |
| Output hold time tCLQX | M95010-R at VCC = 2.5 or 5.0 V; not recommended for new designs. | min 0 ns | 37 |
| Output rise time tQLQH | M95010-R at VCC = 2.5 or 5.0 V; not recommended for new designs; guaranteed by characterization. | max 20 ns | 37 |
| Output fall time tQHQL | M95010-R at VCC = 2.5 or 5.0 V; not recommended for new designs; guaranteed by characterization. | max 20 ns | 37 |
| HOLD high to output valid tHHQV | M95010-R at VCC = 2.5 or 5.0 V; not recommended for new designs. | max 25 ns | 37 |
| HOLD low to output high-Z tHLQZ | M95010-R at VCC = 2.5 or 5.0 V; not recommended for new designs; guaranteed by characterization. | max 35 ns | 37 |
| Write time tW | M95010-R at VCC = 2.5 or 5.0 V; not recommended for new designs. | max 5 ms | 37 |
| Clock frequency fC | M95010-R; VCC = 1.8 V; not recommended for new designs; minimum D.C. | max 5 MHz | 38 |
| S active setup time tSLCH | M95010-R; VCC = 1.8 V; not recommended for new designs. | min 90 ns | 38 |
| S not active setup time tSHCH | M95010-R; VCC = 1.8 V; not recommended for new designs. | min 90 ns | 38 |
| S deselect time tSHSL | M95010-R; VCC = 1.8 V; not recommended for new designs. | min 100 ns | 38 |
| S active hold time tCHSH | M95010-R; VCC = 1.8 V; not recommended for new designs. | min 90 ns | 38 |
| S not active hold time tCHSL | M95010-R; VCC = 1.8 V; not recommended for new designs. | min 90 ns | 38 |
| Clock high time tCH | M95010-R; VCC = 1.8 V; not recommended for new designs; tCH + tCL ≥ 1/fC(max). | min 90 ns | 38 |
| Clock low time tCL | M95010-R; VCC = 1.8 V; not recommended for new designs; tCH + tCL ≥ 1/fC(max). | min 90 ns | 38 |
| Clock rise time tCLCH | M95010-R; VCC = 1.8 V; not recommended for new designs; guaranteed by characterization. | max 1 us | 38 |
| Clock fall time tCHCL | M95010-R; VCC = 1.8 V; not recommended for new designs. | max 1 us | 38 |
| Data in setup time tDVCH | M95010-R; VCC = 1.8 V; not recommended for new designs. | min 20 ns | 38 |
| Data in hold time tCHDX | M95010-R; VCC = 1.8 V; not recommended for new designs. | min 30 ns | 38 |
| Clock low hold time after HOLD not active tHHCH | M95010-R; VCC = 1.8 V; not recommended for new designs. | min 70 ns | 38 |
| Clock low hold time after HOLD active tHLCH | M95010-R; VCC = 1.8 V; not recommended for new designs. | min 40 ns | 38 |
| Clock low setup time before HOLD active tCLHL | M95010-R; VCC = 1.8 V; not recommended for new designs. | min 0 ns | 38 |
| Clock low setup time before HOLD not active tCLHH | M95010-R; VCC = 1.8 V; not recommended for new designs. | min 0 ns | 38 |
| Output disable time tSHQZ | M95010-R; VCC = 1.8 V; not recommended for new designs. | max 100 ns | 38 |
| Clock low to output valid tCLQV | M95010-R; VCC = 1.8 V; not recommended for new designs. | max 80 ns | 38 |
| Output hold time tCLQX | M95010-R; VCC = 1.8 V; not recommended for new designs. | min 0 ns | 38 |
| Output rise time tQLQH | M95010-R; VCC = 1.8 V; not recommended for new designs. | max 50 ns | 38 |
| Output fall time tQHQL | M95010-R; VCC = 1.8 V; not recommended for new designs. | max 50 ns | 38 |
| HOLD high to output valid tHHQV | M95010-R; VCC = 1.8 V; not recommended for new designs. | max 50 ns | 38 |
| HOLD low to output high-Z tHLQZ | M95010-R; VCC = 1.8 V; not recommended for new designs. | max 100 ns | 38 |
| Write time tW | M95010-R; VCC = 1.8 V; not recommended for new designs. | max 5 ms | 38 |

EmielV2002/FRDM_MCXx_SensHat
A hat with sensors and actuators for the FRDM-MCXA153 and FRDM-MCXN947 development boards made by NXP.

EmielV2002/FRDM_MCXx_SensHat
A hat with sensors and actuators for the FRDM-MCXA153 and FRDM-MCXN947 development boards made by NXP.
Yes. The symbol is EasyEDA_Cloud:M25P40-VMN6PBA and the footprint Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, both drawn on this page. PCBKit places them on a board for you when you design with it.
SO-8, with 8 pins. Its footprint is drawn on this page.
STMicroelectronics publishes it: the Datasheet link on this page opens it.
JLCPCB lists it as part C2061643, with 1,585 in stock; the sellers' links on this page open their listings.
Parts like it in the library: the AT25256B-SSHL-T by Microchip Technology, the CAT25256VI-GT3 by onsemi, the AT25128B-SSHL-T by Microchip Technology and the CAT25128VI-GT3 by onsemi. Check their datasheets: a part that fits the footprint may still differ in its ratings.
2 boards in 1 repository on GitHub; the most starred are listed on this page, with their KiCad files.