
ZMOD4410AI1R
Renesas ElectronicsExtended
-40℃~+65℃ 0.7mm 0ppm~1000ppm 1.7V~3.6V 3mm 3mm 7.4mA Carbon dioxide I2C LGA-12 Gas Sensors ROHS
- Part id
- renesas/ZMOD4410AI1R
- Category
- Gas Sensors
- Package
- LGA-12
- Pins
- 12
- In stock
- 0 at JLCPCB (C5342493)
- Used on
- 2 open-source boards
Overview
The ZMOD4410AI1R is a gas Sensor made by Renesas Electronics in a LGA-12 package with 12 pins. -40℃~+65℃ 0.7mm 0ppm~1000ppm 1.7V~3.6V 3mm 3mm 7.4mA Carbon dioxide I2C LGA-12 Gas Sensors ROHS.
PCBKit's library has its KiCad symbol (EasyEDA_Cloud:ZMOD4410AI1R, from EasyEDA) and its footprint (4ms_Package_QFP:LGA-12_2x2mm_P0.5mm, from KiCad's library), ready for a KiCad board. JLCPCB lists it (part C5342493). 2 open-source boards in 2 repositories on GitHub use it.
Symbol
Footprint
From the datasheet
9- Supply, least
- 1.7 V · VDD, minimum supply voltage · p. 6
- Supply, most
- 3.6 V · VDD, maximum supply voltage · p. 6
- Supply, absolute maximum
- 3.63 V · VDD, VDDH, VDDIO, absolute maximum · p. 6
- Takes working
- 7.4 mA · typical active current including heater, IAQ modes, VDD = 1.8 V · p. 7
- Takes working
- 5.2 mA · typical active current including heater, IAQ modes, VDD = 3.3 V · p. 7
- Takes working
- 9.9 mA · typical active current including heater, PBAQ, VDD = 1.8 V · p. 7
- Takes working
- 6.9 mA · typical active current including heater, PBAQ, VDD = 3.3 V · p. 7
- Takes at most
- 16.4 mA · max active current including heater, PBAQ, VDD = 1.8 V · p. 7
- Takes asleep
- 450 nA · typical ASIC sleep current during measurement delays · p. 7
What it is and has
6- Sensor function
- TVOC and indoor air quality · p. 1
- Package
- 12-LGA · p. 1
- External reset
- Active-LOW · p. 1
- Qualification
- JEDEC JESD47, 10 years lifetime · p. 1
- Compliance
- RoHS · p. 1
- Siloxane resistance
- Siloxane resistant · p. 1
Around it
1- cap 100 nF minimum
- between power supply and VSS; Ceramic blocking capacitor; place close to the gas sensor module. · p. 7
Specifications
28| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Supply Voltage VDD | Reference: VSS | min 1.7 · max 3.6 V | 6 |
| Maximum Analog and I/O Supply Voltage VDD, VDDH, VDDIO | Reference: VSS | min -0.4 · max 3.63 V | 6 |
| Maximum Voltage at all Analog and Digital I/O Pins VA_IO, VD_IO | Reference: VSS; maximum is VDDIO + 0.5 V | min -0.5 V | 6 |
| Maximum Difference in Voltage between VDD and VDDH Pins | max 0.4 V | 6 | |
| Input Current into any Pin Except Supply Pins (Latch-Up Immunity) IIN | min -100 · max 100 mA | 6 | |
| Electrostatic Discharge Tolerance – Human Body Model (HBM) VHBM1 | max 2000 V | 6 | |
| Electrostatic Discharge Tolerance – Charged Device Model (CDM) on Packaged Module VCDM | max 750 V | 6 | |
| Maximum Ambient Temperature Range of Sensor Module TAMB-MAX | min -40 · max 125 °C | 6 | |
| Storage Temperature TSTOR | min -50 · max 125 °C | 6 | |
| Operation Temperature of Sensing Element [1] TOPERATION | Controlled via API in firmware and EVK software. | max 550 °C | 6 |
| Average Power: IAQ 2nd Gen, Relative IAQ and Sulfur-based Odor Discrimination | typ 6 mW | 7 | |
| Average Power: IAQ 2nd Gen ULP and Relative IAQ ULP | Ultra-Low Power operation | typ 0.16 mW | 7 |
| Average Power: PBAQ | typ 1 mW | 7 | |
| Supply Current, Active Mode including Heater Current for IAQ 2nd Gen, Relative IAQ, Ultra-low Power and Sulfur-based Odor Discrimination IACTIVE | At VDD = 1.8 V | typ 7.4 · max 16.2 mA | 7 |
| Supply Current, Active Mode including Heater Current for IAQ 2nd Gen, Relative IAQ, Ultra-low Power and Sulfur-based Odor Discrimination IACTIVE | At VDD = 3.3V | typ 5.2 · max 10.3 mA | 7 |
| Supply Current, Active Mode including Heater Current for PBAQ IACTIVE | At VDD = 1.8 V | typ 9.9 · max 16.4 mA | 7 |
| Supply Current, Active Mode including Heater Current for PBAQ IACTIVE | At VDD = 3.3V | typ 6.9 · max 10.6 mA | 7 |
| Current during measurement delays ISLEEP | Sleep Mode ASIC | typ 450 nA | 7 |
| Power Supply Rejection Ratio PSRR | VDD ≥ 2.0V | typ 30 dB | 7 |
| Timing Accuracy (Valid for Measurements Only) (Sleep Timer is ±20%) | At room temperature; for timings derived from the internal clock. | min -2 · max 2 % | 7 |
| Timing Accuracy (Valid for Measurements Only) (Sleep Timer is ±20%) | Over-temperature range; for timings derived from the internal clock. | min -0.1 · max 0.1 %/K | 7 |
| ADC Resolution rADC | min 10 · max 16 Bit | 7 | |
| Start-up Time: VDD Ramp up to Interface Communication tSTA1 | max 1 ms | 7 | |
| I2C Clock Frequency fC,I2C | max 400 kHz | 7 | |
| NVM Programming Time tVPP | typ 6 · max 16 ms | 7 | |
| Data Retention tRET_FTP | 85°C junction temperature | min 10 years | 7 |
| NVM Programming Cycles | min 1000 cycles | 7 | |
| Blocking Capacitor for Power Supply | Ceramic type; recommended to be placed close to gas sensor module | min 100 nF | 7 |
Pins, by the datasheet
12- 1 SCL
- Serial clock for the I2C interface. · p. 5
- 2 SDA
- Serial data for the I2C interface; default 7-bit slave address 32HEX. · p. 5
- 3 INT
- Push-pull interrupt: HIGH during measurement, LOW when finished; use falling-edge detection. · p. 5
- 4 n.c.
- Do not connect. · p. 5
- 5 VDD
- Voltage supply for the ZMOD4410. · p. 5
- 6 VSS
- Ground reference for the ZMOD4410. · p. 5
- 7 VSS
- Ground reference for the ZMOD4410. · p. 5
- 8 n.c.
- Do not connect. · p. 5
- 9 VSS
- Ground reference for the ZMOD4410. · p. 5
- 10 VDDH
- Voltage supply for the integrated heater. · p. 5
- 11 RES_N
- ZMOD4410 reset; active low. · p. 5
- 12 VDDIO
- Voltage supply for the I/O interface. · p. 5
Open-source boards using it
2- 4 layers50 × 110 mm

- 2 layers62 × 57 mm

Parts like it
8ZMOD4450AI1V
LGA-12(3x3)0.7mm 0ppm~10ppm 0℃~+25℃ 1.7V~3.6V 3mm 3mm 7mA Air quality I2C Reset function、Multi-gas detection capability ±2% LGA-12(3x3) Gas Sensors ROHSRenesas ElectronicsGas SensorsZMOD4410AI1V
LGA-12(3x3)-40℃~+65℃ 0.7mm 0ppm~1000ppm 1.7V~3.6V 13mA 3mm 3mm Air quality I2C Reset function ±15% LGA-12(3x3) Gas Sensors ROHSRenesas ElectronicsGas SensorsZMOD4510AI1R
LGA-12(3x3)-40℃~+65℃ Air quality LGA-12(3x3) Gas Sensors ROHSRenesas ElectronicsGas SensorsZMOD4410AI3V
LGA-12(3x3)-40℃~+65℃ 0.7mm 0ppm~1000ppm 1.7V~3.6V 3mm 3mm 5.2mA Air quality I2C Reset function、Multi-gas detection capability ±10% LGA-12(3x3) Gas Sensors ROHSRenesas ElectronicsGas SensorsZMOD4510AI1V
LGA-12(3x3)-40℃~+65℃ 0.02ppm~0.5ppm 0.7mm 1.7V~3.6V 11mA 3mm 3mm Air quality I2C ±15% LGA-12(3x3) Gas Sensors ROHSRenesas ElectronicsGas SensorsZMOD4510AI2V
LGA-12(3x3)-40℃~+65℃ 0.7mm 1.7V~3.6V 20ppb~500ppb 3mm 3mm 8mA Air quality I2C ±15% LGA-12(3x3) Gas Sensors ROHSRenesas ElectronicsGas SensorsZMOD4510AI3V
LGA-12(3x3)-40℃~+65℃ 0.02ppm~0.5ppm 0.9mm 1.7V~3.6V 120uA 3mm 3mm Air quality I2C Reset function、Multi-gas detection capability ±15% LGA-12(3x3) Gas Sensors ROHSRenesas ElectronicsGas SensorsZMOD4510AI4V
LGA-12(3x3)-40℃~+65℃ 0.9mm 1.7V~3.6V 20ppb~500ppb 3mm 3mm 8mA Air quality I2C ±15% LGA-12(3x3) Gas Sensors ROHSRenesas ElectronicsGas Sensors
Questions
Is there a KiCad symbol and footprint for the ZMOD4410AI1R?
Yes. The symbol is EasyEDA_Cloud:ZMOD4410AI1R and the footprint 4ms_Package_QFP:LGA-12_2x2mm_P0.5mm, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the ZMOD4410AI1R?
LGA-12, with 12 pins. Its footprint is drawn on this page.
Where is the ZMOD4410AI1R datasheet?
Renesas Electronics publishes it: the Datasheet link on this page opens it.
Where can I order the ZMOD4410AI1R?
JLCPCB lists it as part C5342493, with 0 in stock; the sellers' links on this page open their listings.
What can replace the ZMOD4410AI1R?
Parts like it in the library: the ZMOD4450AI1V by Renesas Electronics, the ZMOD4410AI1V by Renesas Electronics, the ZMOD4510AI1R by Renesas Electronics and the ZMOD4410AI3V by Renesas Electronics. Check their datasheets: a part that fits the footprint may still differ in its ratings.
Which open-source boards use the ZMOD4410AI1R?
2 boards in 2 repositories on GitHub; the most starred are listed on this page, with their KiCad files.