
L96-M33
QuectelExtended
-148dBm -40℃~+85℃ 1.561098GHz、1.57542GHz、1.57542GHz、1.602GHz 2.8V~4.3V Receive UART、I2C SMD-31P RF Modules ROHS
- Part id
- quectel/L96-M33
- Category
- RF Modules
- Package
- SMD-31P
- Pins
- 31
- In stock
- 317 at JLCPCB (C5197298)
- Used on
- 7 open-source boards
Overview
The L96-M33 is a RF Module made by Quectel in a SMD-31P package with 31 pins. -148dBm -40℃~+85℃ 1.561098GHz、1.57542GHz、1.57542GHz、1.602GHz 2.8V~4.3V Receive UART、I2C SMD-31P RF Modules ROHS.
PCBKit's library has its KiCad symbol (EasyEDA_Cloud:L96-M33, from EasyEDA) and its footprint (EasyEDA_Cloud:WIRELM-SMD_L96-M33, from EasyEDA), ready for a KiCad board. 317 are in stock at JLCPCB (part C5197298). 7 open-source boards in 6 repositories on GitHub use it.
Symbol
Footprint
From the datasheet
11- Supply, least
- 2.8 V · VCC, recommended operating min · p. 42
- Supply, most
- 4.3 V · VCC, recommended operating max · p. 42
- Supply, least
- 1.5 V · V_BCKP, recommended operating min · p. 42
- Supply, most
- 4.5 V · V_BCKP, recommended operating max · p. 42
- Supply, absolute maximum
- 4.5 V · VCC, absolute max · p. 41
- Works from
- -40 °C · Full on mode operating temperature min · p. 42
- Works up to
- 85 °C · Full on mode operating temperature max · p. 42
- Takes working
- 22 mA · Typical GPS+GLONASS tracking, -130dBm, VCC=3.3V · p. 11
- Takes at most
- 150 mA · Peak supply current max, VCC=3.3V · p. 42
- Takes asleep
- 450 µA · Standby current, VCC=3.3V · p. 42
- Takes asleep
- 7 µA · Backup current, V_BCKP=3.3V · p. 42
What it is and has
13- Positioning systems
- GPS, GLONASS, Galileo with RLM support, BeiDou · p. 10
- GNSS augmentation
- SBAS including WAAS, EGNOS, MSAS and GAGAN; QZSS, DGPS and AGPS · p. 10
- Package dimensions
- 14.0mm × 9.6mm × 2.0mm, SMD · p. 10
- Package pads
- 31 pins, 1.0mm pitch · p. 10
- Compliance
- EU RoHS · p. 10
- Update rate
- 1Hz default, up to 10Hz · p. 11
- Horizontal position accuracy
- <2.5m CEP @-130dBm, autonomous · p. 11
- 1PPS accuracy
- Typical <10ns · p. 11
- 1PPS pulse width
- 100ms · p. 11
- UART
- TXD1 and RXD1 · p. 11
- UART baud rate
- 4800bps to 115200bps · p. 11
- EPO offline AGPS
- 30-day orbit predictions · p. 32
- Active interference cancellation
- 12 single-tone interference signals · p. 32
Around it
9- cap 4.7uF
- between V_BCKP and GND; RTC backup reference circuit. · p. 21
- cap 100nF
- between V_BCKP and GND; RTC backup reference circuit. · p. 21
- res 0Ω
- between C1 and RF_IN; R1, default series antenna matching resistor in active antenna reference design without ANTON. · p. 36
- cap 100pF
- between Active Antenna and R1; C1, series capacitor in active antenna reference design without ANTON. · p. 36
- ind 47nH
- between Active Antenna and R2; L1, minimum recommended inductance; routes antenna bias and prevents RF leakage into VCC_3V3. · p. 36
- res 10R
- between L1 and VCC_3V3; R2, active antenna short-circuit protection. · p. 36
- cap 100pF
- between Passive Antenna and R1; C1, series capacitor in the passive antenna reference design without external LNA. · p. 38
- res 0Ω
- between C1 and RF_IN; R1, default series matching resistor in the passive antenna reference design without external LNA. · p. 38
- cap 56pF
- between LNA RF OUT and RF_IN; C4 in the passive antenna reference design with external LNA; value can be optimized. · p. 38
Specifications
62| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Power Supply Voltage (VCC) VCC | min -0.3 · max 4.5 V | 41 | |
| Backup Battery Voltage (V_BCKP) V_BCKP | min -0.3 · max 4.5 V | 41 | |
| Input Voltage at Digital Pins | min -0.3 · max 3.6 V | 41 | |
| Input Power at RF_IN (PRF_IN) PRF_IN | min -154 · max 15 dBm | 41 | |
| Supply voltage VCC | The actual input voltages must stay between the minimum and maximum values. | min 2.8 · typ 3.3 · max 4.3 V | 42 |
| Peak supply current IVCCP | VCC=3.3V | max 150 mA | 42 |
| Backup voltage supply V_BCKP | min 1.5 · typ 3.3 · max 4.5 V | 42 | |
| Operating temperature range in full on mode TOPR | Full on mode | min -40 · typ 25 · max 85 °C | 42 |
| Acquisition | L96, @-130dBm GPS, @3.3V | typ 22 mA | 42 |
| Tracking | L96, @-130dBm GPS, @3.3V | typ 19 mA | 42 |
| Acquisition | L96, @-130dBm GPS+GLONASS, @3.3V | typ 25 mA | 42 |
| Tracking | L96, @-130dBm GPS+GLONASS, @3.3V | typ 22 mA | 42 |
| Standby | L96, @3.3V | typ 0.45 mA | 42 |
| Backup | L96, @V_BCKP=3.3V | typ 7 uA | 42 |
| Static | In GLP Mode | typ 8.8 mA | 26 |
| Static | In Normal Mode | typ 22 mA | 26 |
| Walking | In GLP Mode | typ 9.6 mA | 26 |
| Walking | In Normal Mode | typ 24 mA | 26 |
| Running | In GLP Mode | typ 11.6 mA | 26 |
| Running | In Normal Mode | typ 29 mA | 26 |
| Driving | In GLP Mode | typ 12.8 mA | 26 |
| Driving | In Normal Mode | typ 32 mA | 26 |
| Backup power supply V_BCKP | Pin 8 | max 4.5 V | 15 |
| Backup power supply V_BCKP | Pin 8 | min 1.5 V | 15 |
| Backup power supply V_BCKP | Pin 8, nominal | typ 3.3 V | 15 |
| Main power supply VCC | Pin 9 | max 4.3 V | 15 |
| Main power supply VCC | Pin 9 | min 2.8 V | 15 |
| Main power supply VCC | Pin 9, nominal | typ 3.3 V | 15 |
| Reset the module VIL | RESET, pin 23 | min -0.3 V | 15 |
| Reset the module VIL | RESET, pin 23 | max 0.7 V | 15 |
| Reset the module VIH | RESET, pin 23 | min 2.1 V | 15 |
| Reset the module VIH | RESET, pin 23 | max 3.1 V | 15 |
| Transmit data VOL | TXD1, pin 25 | max 0.42 V | 16 |
| Transmit data VOH | TXD1, pin 25 | min 2.4 V | 16 |
| Transmit data VOH | TXD1, pin 25, nominal | typ 2.8 V | 16 |
| Receive data VIL | RXD1, pin 26 | min -0.3 V | 16 |
| Receive data VIL | RXD1, pin 26 | max 0.7 V | 16 |
| Receive data VIH | RXD1, pin 26 | min 2.1 V | 16 |
| Receive data VIH | RXD1, pin 26 | max 3.1 V | 16 |
| External LNA and active antenna power control VOL | ANTON, pin 30 | max 0.42 V | 16 |
| External LNA and active antenna power control VOH | ANTON, pin 30 | min 2.4 V | 16 |
| External LNA and active antenna power control VOH | ANTON, pin 30, nominal | typ 2.8 V | 16 |
| Used to enter into or exit from standby mode. VIL | EXTINT0, pin 7 | min -0.3 V | 16 |
| Used to enter into or exit from standby mode. VIL | EXTINT0, pin 7 | max 0.7 V | 16 |
| One pulse per second VOL | TIMEPULSE, pin 29 | max 0.42 V | 16 |
| One pulse per second VOH | TIMEPULSE, pin 29 | min 2.4 V | 16 |
| Wake from backup mode VIL | FORCE_ON, pin 28 | min -0.3 V | 16 |
| Wake from backup mode VIL | FORCE_ON, pin 28 | max 0.7 V | 16 |
| I2C serial data VIL | I2C_SDA, pin 3; remaining characteristics continue on an unavailable page | min -0.3 V | 16 |
| Acquisition | L96; @-130dBm GPS; @3.3V | typ 22 mA | 42 |
| Tracking | L96; @-130dBm GPS; @3.3V | typ 19 mA | 42 |
| Acquisition | L96; @-130dBm GPS+GLONASS; @3.3V | typ 25 mA | 42 |
| Tracking | L96; @-130dBm GPS+GLONASS; @3.3V | typ 22 mA | 42 |
| Standby | L96; @3.3V | typ 0.45 mA | 42 |
| Backup | L96; @V_BCKP=3.3V | typ 7 uA | 42 |
| Max slope | Soak Zone | min 1 · max 3 °C/sec | 49 |
| Soak time (between A and B: 150°C and 200°C) | Soak Zone | min 60 · max 120 sec | 49 |
| Max slope | Reflow Zone | min 2 · max 3 °C/sec | 49 |
| Reflow time (D: over 220°C) | Reflow Zone | min 40 · max 60 sec | 49 |
| Max temperature | Reflow Zone | min 240 · max 245 °C | 50 |
| Cooling down slope | min 1 · max 4 °C/sec | 50 | |
| Max reflow cycle | Reflow Cycle | max 1 | 50 |
Pins, by the datasheet
31- 1 NC
- NC. · p. 14
- 2 3D_FIX
- 3D_FIX interface. · p. 14
- 3 I2C_SDA
- I2C serial data. · p. 16
- 4 GND
- Ground. · p. 14
- 5 GND
- Ground. · p. 14
- 6 I2C_SCL
- I2C_SCL interface. · p. 14
- 7 EXTINT0
- Edge-triggered standby control, pulled up internally; leave open if unused. · p. 16
- 8 V_BCKP
- Backup supply for RTC domain when VCC is powered off. · p. 15
- 9 VCC
- Main power supply; provide at least 150mA current capability. · p. 15
- 10 GND
- Ground. · p. 14
- 11 GND
- Ground. · p. 14
- 12 GND
- Ground. · p. 14
- 13 GND
- Ground. · p. 14
- 14 GND
- Ground. · p. 14
- 15 GND
- Ground. · p. 14
- 16 RF_OUT
- RF signal output; 50Ω characteristic impedance. · p. 16
- 17 RF_IN
- RF signal input; 50Ω characteristic impedance. · p. 16
- 18 GND
- Ground. · p. 14
- 19 GND
- Ground. · p. 14
- 20 JAM_IND
- JAM_IND interface. · p. 14
- 21 GND
- Ground. · p. 14
- 22 GND
- Ground. · p. 14
- 23 RESET
- Active-low module reset; leave open or connect to VCC if unused. · p. 15
- 24 GEO_FENCE
- GEO_FENCE interface. · p. 14
- 25 TXD1
- UART transmit data for NMEA output, commands and firmware upgrade. · p. 16
- 26 RXD1
- UART receive data for commands and firmware upgrade. · p. 16
- 27 GND
- Ground. · p. 14
- 28 FORCE_ON
- High wakes the module from backup mode; keep open or low before entering backup mode; belongs to RTC domain. · p. 12
- 29 TIMEPULSE
- One pulse per second, synchronized at rising edge, 100ms pulse width; leave open if unused. · p. 16
- 30 ANTON
- External LNA and active antenna power control in power saving mode; leave open if unused. · p. 16
- 31 GND
- Ground. · p. 14
Open-source boards using it
7- 2 layers29.4 × 32 mm

- 4 layers140 × 100 mm

- 2 layers42 × 42 mm

SportsWatch
HaydenGillen/SportsWatch
This GPS watch project began from my interest in building a custom fitness device that records accurate run and cycle data and allows users to create and implement their own features.
49 parts - 2 layers70 × 82 mm

EspSkipper2
kisbAlt/espSkipper_v2
ESP32 based, open source, low cost boat instrumentation to replace proprietary marine systems.
74 parts - 2 layers52.5 × 27.5 mm

- 4 layers111.7 × 137 mm

- 4 layers45 × 31 mm

L96-M33 Breakout
oiver12/VariometerV2
Paragliding variometer: custom KiCad PCBs, ESP32 firmware, sensor fusion, e-ink UI, and desktop flight replay.
18 partsMIT
Parts like it
1Questions
Is there a KiCad symbol and footprint for the L96-M33?
Yes. The symbol is EasyEDA_Cloud:L96-M33 and the footprint EasyEDA_Cloud:WIRELM-SMD_L96-M33, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the L96-M33?
SMD-31P, with 31 pins. Its footprint is drawn on this page.
Where is the L96-M33 datasheet?
Quectel publishes it: the Datasheet link on this page opens it.
Where can I order the L96-M33?
JLCPCB lists it as part C5197298, with 317 in stock; the sellers' links on this page open their listings.
What can replace the L96-M33?
Parts like it in the library: the L26UDR-S89 by Quectel. Check their datasheets: a part that fits the footprint may still differ in its ratings.
Which open-source boards use the L96-M33?
7 boards in 6 repositories on GitHub; the most starred are listed on this page, with their KiCad files.