NCP692MN33
onsemiExtended
-40℃~+125℃@(Tj) 1 145uA 180mV@(1A) 1A 3.3V 50uVrms 6V Fixed Over Current Protection、Over Temperature Protection、Enable Positive DFN-6(3x3) Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHS
- Part id
- onsemi/NCP692MN33
- Category
- Voltage Regulators, Linear, Low Drop Out (LDO) Regulators
- Package
- DFN-6(3x3)
- Pins
- 7
- In stock
- 11 at JLCPCB (C145519)
Overview
The NCP692MN33 is a voltage Regulators, Linear, Low Drop Out (LDO) Regulator made by onsemi in a DFN-6(3x3) package with 7 pins. -40℃~+125℃@(Tj) 1 145uA 180mV@(1A) 1A 3.3V 50uVrms 6V Fixed Over Current Protection、Over Temperature Protection、Enable Positive DFN-6(3x3) Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHS.
PCBKit's library has its KiCad symbol (EasyEDA_Cloud:NCP692MN33T2G, from EasyEDA) and its footprint (EasyEDA_Cloud:DFN-6_L3.0-W3.0-P0.95-LS3.1-BL-EP, from EasyEDA), ready for a KiCad board. 11 are in stock at JLCPCB (part C145519).
Symbol
Footprint
From the datasheet
14- Supply, least
- 1.5 V · VIN, recommended operating min; VIN must also exceed VOUT + VDO · p. 5
- Supply, most
- 6 V · VIN, recommended operating max · p. 5
- Supply, absolute maximum
- 6.5 V · VIN, absolute max · p. 5
- Junction, hottest
- 150 °C · Junction temperature absolute max · p. 5
- Gives
- 1 A · Guaranteed continuous output current · p. 1
- Output
- 3.3 V · Fixed output voltage typical · p. 6
- Dropout
- 180 mV · Typical at IOUT = 1 A, VOUT = 3.3 V · p. 6
- Takes working
- 145 mA · Typical ground current, VIN = VOUT + 1 V, IOUT = 1 A; unit as supplied · p. 6
- Takes asleep
- 100 µA · Typical disable current, VEN < 0.4 V; unit as supplied · p. 6
- Current limit
- 1.6 A · Typical output current limit, VIN = VOUT + 1 V, VOUT = 85% VOUT_NOM · p. 6
- Junction to air (DFN6 3x3)
- 169 K/W · Junction to ambient, 1 oz Cu, 64 mm2 Cu · p. 5
- Junction to air (DFN6 3x3)
- 70 K/W · Junction to ambient, 1 oz Cu, 645 mm2 Cu · p. 5
- Junction to air (DFN6 3x3)
- 151 K/W · Junction to ambient, 2 oz Cu, 64 mm2 Cu · p. 5
- Junction to air (DFN6 3x3)
- 62 K/W · Junction to ambient, 2 oz Cu, 645 mm2 Cu · p. 5
What it is and has
6- Output current
- 1 A guaranteed · p. 1
- Output discharge
- Active · p. 1
- Enable
- Active high · p. 1
- ESD
- 4 kV and 200 V · p. 1
- Lead finish
- Pb-Free · p. 1
- Protection
- short circuit and thermal protection · p. 1
Around it
3- cap 10 mF
- between IN and GND; Ceramic input decoupling capacitor recommended close to the package; value and unit as supplied. · p. 12
- cap 1 mF
- between OUT and GND; Minimum output decoupling capacitance for stability; ceramic or tantalum. Value and unit as supplied. · p. 12
- cap 10 mF
- between OUT and GND; Recommended for improved load transient response and startup performance; value and unit as supplied. · p. 12
Specifications
32| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Input Voltage (Note 1) VIN | min -0.3 · max 6.5 V | 5 | |
| Chip Enable Voltage VEN | min -0.3 · max 6.5 V | 5 | |
| Output Voltage VOUT | min -0.3 · max 6.5 V | 5 | |
| Output Voltage / Sense Input, (SNS pin) VSNS | min -0.3 · max 6.5 V | 5 | |
| Electrostatic Discharge ESD | Human Body Model | max 4000 V | 5 |
| Electrostatic Discharge ESD | Machine Model | max 200 V | 5 |
| Maximum Junction Temperature TJ_MAX | max 150 _C | 5 | |
| Storage Temperature Range TSTG | min -65 · max 150 _C | 5 | |
| Thermal Resistance, Junction−to−Ambient (Note 2) RqJA | DFN6 3x3, 1 oz Cu, 64 mm2 Cu | typ 169 °C/W | 5 |
| Thermal Resistance, Junction−to−Ambient (Note 2) RqJA | DFN6 3x3, 1 oz Cu, 645 mm2 Cu | typ 70 °C/W | 5 |
| Thermal Resistance, Junction−to−Ambient (Note 2) RqJA | DFN6 3x3, 2 oz Cu, 64 mm2 Cu | typ 151 °C/W | 5 |
| Thermal Resistance, Junction−to−Ambient (Note 2) RqJA | DFN6 3x3, 2 oz Cu, 645 mm2 Cu | typ 62 °C/W | 5 |
| Thermal Resistance, Junction−to−Pin RqJL | DFN6 3x3 | typ 15 °C/W | 5 |
| Operating Input Voltage (Notes 3 and 4) VIN | Minimum VIN = (VOUT + VDO) or 1.5 V, whichever is higher. | min 1.5 · max 6 V | 5 |
| Operating Junction Temperature Range TJ | min -40 · max 125 °C | 5 | |
| Output voltage (Fixed Version) VOUT | VOUT = 3.3 V; VIN = (VOUT + 1 V) to 6.0 V; IOUT = 100 mA to 1 A | min 3.234 · typ 3.3 · max 3.366 V | 6 |
| Line regulation RegLINE | VIN = (VOUT + 1 V) to 6.0 V | typ 3.2 · max 8 mV | 6 |
| Load regulation RegLOAD | VOUT = 3.3 V; IOUT = 100 mA to 1 A | typ 10 · max 35 mV | 6 |
| Dropout voltage (Fixed Version, Note 9) VDO | VOUT = 3.3 V; IOUT = 1 A | typ 180 · max 250 mV | 6 |
| Ground current IGND | VIN = VOUT + 1 V; VOUT = 3.3 V; IOUT = 1 A | typ 145 · max 200 mA | 6 |
| Ground current IGND | VIN = VOUT + 1 V; VOUT = 3.3 V; IOUT = 10 mA | typ 145 · max 200 mA | 6 |
| Ground current IGND | VIN = VOUT + 1 V; VOUT = 3.3 V; IOUT = 100 mA | typ 145 · max 200 mA | 6 |
| Disable current (NCP692 only, Notes 5 and 7) IDIS | VEN < 0.4 V | typ 0.1 · max 1 mA | 6 |
| Output Current Limit ILIM | VIN = VOUT + 1 V, VOUT = 85% VOUT_NOM | min 1.1 · typ 1.6 · max 2.4 A | 6 |
| Short Circuit Current ISC | VOUT = 0 V | min 1.2 A | 6 |
| Enable High Level Threshold VEN_ HI | VEN increasing from low to high logic level | min 0.9 V | 6 |
| Enable Low Level Threshold (NCP691 and NCP692) VEN_ LO | VEN decreasing from high to low logic level | max 0.4 V | 6 |
| Enable Input Current (NCP692 only, Note 8) IEN_LO | VEN = 0 V | typ 0.01 · max 100 nA | 6 |
| Turn−on Time (Note 8) tON | VIN = 0 V to (VOUT +1 V) or 1.75 V; VOUT = 0 V to 90% VOUT_NOM | typ 50 ms | 7 |
| Output noise voltage (Note 8) VN | BW = 200 Hz to 100 kHz, CIN = 1 mF, COUT = 10 mF, TA = 25°C | typ 50 mVrms | 7 |
| Thermal Shutdown Temperature (Note 8) TSD | typ 175 °C | 7 | |
| Thermal Shutdown Hysteresis (Note 8) TSH | typ 10 °C | 7 |
Pins, by the datasheet
6- 1 IN
- Regulator voltage input; connect both IN pins together for full output current capability. · p. 3
- 2 GND
- Power supply ground; solder to the copper plane for effective heat removal. · p. 3
- 3 EN
- Active high enable for NCP692. · p. 3
- 4 OUT
- Regulated output voltage. · p. 3
- 5 SNS
- Sense input; connect directly to OUT pin. · p. 3
- 6 IN
- Regulator voltage input; connect both IN pins together for full output current capability. · p. 3
Ordering codes, by the datasheet
1- NCP692MN33T2G
- DFN6 (Pb-Free) · 3.3 V output; 3000 / Tape & Reel · p. 14
Parts like it
8NCP708MU330TA
DFN-6(3x3)-40℃~+125℃@(Tj) 1 100uVrms 180uA 1A 3.3V 330mV@(1A) 5.5V 70dB@(1kHz) Fixed Over Current Protection、Over Temperature Protection、Enable Positive DFN-6(3x3) Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSonsemiVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsNCP690MN33
DFN-6(3x3)-40℃~+125℃@(Tj) 1 145uA 180mV@(1A) 1A 3.3V 50uVrms 6V Fixed Over Current Protection、Over Temperature Protection、Enable Positive DFN-6(3x3) Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSonsemiVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsAMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsAMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.3V@(1A) 12V 1A 3.3V 5mA 60dB@(120Hz) Fixed Over Current Protection Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSUMWVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsAMS1117-3.3V
SOT-2230℃~+125℃@(Ta) 1 12mA 15V 1A 20mV@(1A) 3.3V Fixed Positive SOT-89 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSMSKSEMIVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsAMS1117-3.3S
SOT-89-40℃~+125℃ 0.003%Vout 1 1.3V@(1A) 18V 1A 3.3V 5mA 60dB@(120Hz) Fixed Over Current Protection Positive SOT-89 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSUMWVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsNCP1117ST33
SOT-2230.003%Vout 0℃~+125℃@(Ta) 1 1.2V@(800mA) 1A 20V 3.3V 62dB@(120Hz) 6mA Fixed Over Current Protection、Thermal Shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSonsemiVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsAZ1117H-3.3TRE1
SOT-223-40℃~+125℃@(Tj) 0.003%Vout 1 1.15V@(1A) 15V 1A 3.3V 5mA 75dB@(120Hz) Fixed Over Current Protection、Over Temperature Protection Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSDiodes IncorporatedVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
Questions
Is there a KiCad symbol and footprint for the NCP692MN33?
Yes. The symbol is EasyEDA_Cloud:NCP692MN33T2G and the footprint EasyEDA_Cloud:DFN-6_L3.0-W3.0-P0.95-LS3.1-BL-EP, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the NCP692MN33?
DFN-6(3x3), with 7 pins. Its footprint is drawn on this page.
Where is the NCP692MN33 datasheet?
onsemi publishes it: the Datasheet link on this page opens it.
Where can I order the NCP692MN33?
JLCPCB lists it as part C145519, with 11 in stock; the sellers' links on this page open their listings.
What can replace the NCP692MN33?
Parts like it in the library: the NCP708MU330TA by onsemi, the NCP690MN33 by onsemi, the AMS1117-3.3 by Advanced Monolithic Systems and the AMS1117-3.3 by UMW. Check their datasheets: a part that fits the footprint may still differ in its ratings.