Skip to the content
12345

NCP115ASN330

onsemiExtended

-40℃~+85℃@(Tj) 1 280mV@(300mA) 3.3V 300mA 5.5V 70dB@(1kHz) 70uVrms Fixed Over Current Protection、Over Temperature Protection、Enable、Short Circuit Protection Positive TSOP-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHS

Part id
onsemi/NCP115ASN330
Category
Voltage Regulators, Linear, Low Drop Out (LDO) Regulators
Package
TSOP-5
Pins
5
In stock
3,914 at JLCPCB (C603505)
Used on
5 open-source boards

Overview

The NCP115ASN330 is a voltage Regulators, Linear, Low Drop Out (LDO) Regulator made by onsemi in a TSOP-5 package with 5 pins. -40℃~+85℃@(Tj) 1 280mV@(300mA) 3.3V 300mA 5.5V 70dB@(1kHz) 70uVrms Fixed Over Current Protection、Over Temperature Protection、Enable、Short Circuit Protection Positive TSOP-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHS.

PCBKit's library has its KiCad symbol (EasyEDA_Cloud:TLV77512PDBVR, from EasyEDA) and its footprint (Package_SO:TSOP-5_1.65x3.05mm_P0.95mm, from KiCad's library), ready for a KiCad board. 3,914 are in stock at JLCPCB (part C603505). 5 open-source boards in 4 repositories on GitHub use it.

Symbol

1IN2GND3EN4N/C5OUT
EasyEDA_Cloud:TLV77512PDBVRFrom EasyEDA

Footprint

12345
Package_SO:TSOP-5_1.65x3.05mm_P0.95mmFrom KiCad's library

From the datasheet

11
Supply, least
1.7 V · IN, recommended operating min · p. 3
Supply, most
5.5 V · IN, recommended operating max · p. 3
Supply, absolute maximum
6 V · IN, absolute max · p. 2
Junction, hottest
150 °C · Junction temperature absolute max · p. 2
Takes working
50 mA · IN, typical quiescent current at IOUT = 0 mA; unit as printed · p. 3
Takes asleep
10 µA · IN, typical shutdown current at VEN ≤ 0.4 V, VIN = 5.5 V; unit as printed · p. 3
Gives
300 mA · Rated output current · p. 1
Current limit
600 mA · Typical at VOUT = 90% VOUT(nom) · p. 3
Dropout
235 mV · Typical, TSOP−5, VOUT = 3.3 V, IOUT = 300 mA · p. 3
Junction to air (TSOP−5)
162 K/W · Junction-to-air, 1 oz FR 4 PCB with 645 mm2 Cu area · p. 2
Output
3.3 V · fixed output, NCP115ASN330 · p. 16

What it is and has

9
Output current
300 mA · p. 1
Soft start
Two VOUT slew rate speeds · p. 1
Accuracy
±1% at room temperature · p. 1
Protection
Thermal shutdown and current limit · p. 1
Package options
XDFN4 and TSOP−5 · p. 1
Lead finish
Pb−Free · p. 1
Active output discharge
Present in NCP115A · p. 2
Protection
output overload, output short circuit, overheating · p. 12
Output behavior
300 mA, active discharge, normal slew rate · p. 16

Around it

4
cap 1 mF
between OUT and GND; Minimum ceramic capacitance for stability; unit preserved as printed. · p. 2
cap small capacitor
between IN and GND; Required for stability; value not specified in the pin description. · p. 2
cap at least 1 mF
between IN and GND; Ceramic X5R or X7R; place as close as possible to IN. Unit retained as printed. · p. 12
cap 1 mF
between OUT and GND; X7R or X5R; place as close as possible to OUT. Minimum effective capacitance is 0.47 mF. Units retained as printed. · p. 12

Specifications

31
ParameterConditionsAs printedPage
Input Voltage (Note 1) VINmin -0.3 · max 6 V2
Output Voltage VOUTMaximum: VIN + 0.3 V or 6 Vmin -0.3 V2
Enable Input VENmin -0.3 · max 6 V2
Maximum Junction Temperature TJ(MAX)max 150 °C2
Storage Temperature TSTGmin -55 · max 150 °C2
ESD Capability, Human Body Model (Note 2) ESDHBMmax 2000 V2
ESD Capability, Machine Model (Note 2) ESDMMmax 200 V2
Thermal Resistance, Junction−to−Air RqJATSOP−5; single component mounted on 1 oz, FR 4 PCB with 645 mm2 Cu areatyp 162 °C/W2
Operating Input Voltage VINmin 1.7 · max 5.5 V3
Output Voltage Accuracy VOUT−40°C ≤ TJ ≤ 85°C; VOUT > 2.0 Vmin -2 · max 2 %3
Line Regulation RegLINEVOUT + 0.5 V ≤ VIN ≤ 5.5 V (VIN ≥ 1.7 V)typ 0.01 · max 0.1 %/V3
Load Regulation − TSOP−5 package RegLOADIOUT = 1 mA to 300 mAtyp 28 · max 45 mV3
Dropout Voltage − TSOP−5 package VDOIOUT = 300 mA; VOUT = 3.3 V; Note 5typ 235 · max 280 mV3
Output Current Limit ICLVOUT = 90% VOUT(nom)min 300 · typ 600 mA3
Quiescent Current IQIOUT = 0 mAtyp 50 · max 95 mA3
Shutdown Current IDISVEN ≤ 0.4 V, VIN = 5.5 Vtyp 0.01 · max 1 mA3
High Threshold VEN_HIVEN Voltage increasingmin 0.9 V3
Low Threshold VEN_LOVEN Voltage decreasingmax 0.4 V3
VOUT Slew Rate (Note 6) VOUT_SRVOUT = 3.3 V, IOUT = 10 mA; Normal, version Atyp 190 mV/ms3
EN Pin Input Current IENVEN = 5.5 Vtyp 0.3 · max 1 mA3
Power Supply Rejection Ratio PSRRVIN = 3.8 V, VOUT = 3.5 V; IOUT = 10 mA; f = 1 kHztyp 70 dB3
Output Noise Voltage VNf = 10 Hz to 100 kHztyp 70 mVrms3
Thermal Shutdown Temperature TSDTemperature increasing from TJ = +25°Ctyp 160 °C3
Thermal Shutdown Hysteresis TSDHTemperature falling from TSDtyp 20 °C3
Active Output Discharge Resistance RDISVEN < 0.4 V, Version Atyp 100 W3
RMS Output NoiseVOUT = 3.3 V; VIN = 4.3 V; IOUT = 1 mA; 10 Hz − 100 kHztyp 104 mVRMS7
RMS Output NoiseVOUT = 3.3 V; VIN = 4.3 V; IOUT = 1 mA; 100 Hz − 100 kHztyp 98 mVRMS7
RMS Output NoiseVOUT = 3.3 V; VIN = 4.3 V; IOUT = 10 mA; 10 Hz − 100 kHztyp 102.9 mVRMS7
RMS Output NoiseVOUT = 3.3 V; VIN = 4.3 V; IOUT = 10 mA; 100 Hz − 100 kHztyp 96.7 mVRMS7
RMS Output NoiseVOUT = 3.3 V; VIN = 4.3 V; IOUT = 300 mA; 10 Hz − 100 kHztyp 131.4 mVRMS7
RMS Output NoiseVOUT = 3.3 V; VIN = 4.3 V; IOUT = 300 mA; 100 Hz − 100 kHztyp 127 mVRMS7

Pins, by the datasheet

5
1 IN
Input pin; a small capacitor to ground is needed for stability. · p. 2
2 GND
Power supply ground. · p. 2
3 EN
Drive above 0.9 V to turn on; below 0.4 V for shutdown. · p. 2
4 N/C
Not connected; may be tied to ground to improve thermal dissipation. · p. 2
5 OUT
Regulated output; requires a ceramic capacitor of at least 1 mF to ground for stability. · p. 2

Ordering codes, by the datasheet

2
NCP115ASN330T1G
TSOP−5 · 3.3 V; active discharge, normal slew rate; Pb-free; 3000 / Tape & Reel · p. 16
NCP115ASN330T2G
TSOP−5 · 3.3 V; active discharge, normal slew rate; Pb-free; 3000 / Tape & Reel · p. 16

Open-source boards using it

5
  • 4 layers50 × 30 mmPicodvi, the printed circuit board in 3D

    Picodvi

    Fr4nkFletcher/ESP32-Marauder-Cheap-Yellow-Display

    ESP32Marauder Cheap Yellow Display

    55 parts1.8kMIT
  • 4 layers100 × 50 mmPicostation, the printed circuit board in 3D

    Picostation

    Wren6991/PicoStation3D

    3D games console based on RP2040 and iCE40 UP5k

    78 parts50CC0-1.0
  • 4 layers50 × 30 mmProtoB, the printed circuit board in 3D

    ProtoB

    X65/schematic

    X65 hardware schematic

    63 parts8

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the NCP115ASN330?

Yes. The symbol is EasyEDA_Cloud:TLV77512PDBVR and the footprint Package_SO:TSOP-5_1.65x3.05mm_P0.95mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the NCP115ASN330?

TSOP-5, with 5 pins. Its footprint is drawn on this page.

Where is the NCP115ASN330 datasheet?

onsemi publishes it: the Datasheet link on this page opens it.

Where can I order the NCP115ASN330?

JLCPCB lists it as part C603505, with 3,914 in stock; the sellers' links on this page open their listings.

What can replace the NCP115ASN330?

Parts like it in the library: the NCV8161ASN330 by onsemi, the NCP164ASN330T1G by onsemi, the NCP703SN33 by onsemi and the NCV8164ASN330 by onsemi. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the NCP115ASN330?

5 boards in 4 repositories on GitHub; the most starred are listed on this page, with their KiCad files.