4 layers20.3 × 45.5 mm
SX1257-PMOD
xil-se/SX1257-PMOD
This is a PMOD built around the SX1257 transceiver. It uses an I2C-SPI bridge (SC18IS602B) since only 8 io pins are used.
48 parts21
SC18IS602B
NXP Semiconductors
I2C-Bus to SPI Bridge
- Part id
- nxp/SC18IS602B
- Category
- Uncategorised
- Package
- TSSOP16
- Pins
- 16
- Used on
- 6 open-source boards
Overview
The SC18IS602B is an uncategorised made by NXP Semiconductors in a TSSOP16 package with 16 pins. I2C-Bus to SPI Bridge.
PCBKit's library has its KiCad symbol (Logic:SC18IS602B, from CERN's library) and its footprint (Package_SO:TSSOP-16_4.4x5mm_P0.65mm, from KiCad's library), ready for a KiCad board. 6 open-source boards in 6 repositories on GitHub use it.
Symbol
Footprint
Pinout
16| Pin | Name | Type |
|---|---|---|
| 1 | SS0/GPIO0 | Input/output |
| 2 | SS1/GPIO1 | Input/output |
| 3 | RESET | Input |
| 4 | VSS | Power in |
| 5 | MISO | Input |
| 6 | MOSI | Output |
| 7 | SDA | Input/output |
| 8 | SCL | Input |
| 9 | INT | Output |
| 10 | SS2/GPIO2 | Input/output |
| 11 | SPICLK | Output |
| 12 | VDD | Power in |
| 13 | SS3/GPIO3 | Input/output |
| 14 | A0 | Input |
| 15 | A1 | Input |
| 16 | A2 | Input/output |
Open-source boards using it
6- 2 layers155 × 114 mm
IOExpansion
ja1umi/MUTIF09Project
Various design materials for building my 8-bit-microprocessor-based single board computer(s)
198 parts10MIT - 2 layers50 × 35 mm
Epaper
meerstern/e-Paper_I2C_Module
e-Paper I2Cモジュールは[WAVESHARE製200x200, 1.54inch E-Inkディスプレイ][0]を搭載したモジュールです。 [WAVESHARE製200x200, 1.54inch E-Inkディスプレイ][0]はSPI接続ですが、 配線の容易性を実現するために[SPI I2CプロトコルブリッジIC SC18IS602B][1]を搭載してI2C化しています。…
38 parts2 - 2 layers30 × 40.1 mm
I2CSPI01
mlab-modules/I2CSPI01
Allows connection of SPI devices to I2C bus and is capable co handle up to four SPI slaves. Not used chip-select pins can be used as GPIO pins.
22 parts - 4 layers36.2 × 17.9 mm
- 2 layers58 × 43 mm
Parts like it
8
TPC116S8-TR
TSSOP-16-40℃~+125℃ 14us 16 2.7V~5.5V 8 800uA 8LSB Power-on reset、Power-down mode、Multi-chip synchronization、Output short-circuit protection SPI、QSPI Voltage Buffer TSSOP-16 Digital to Analog Converters (DAC) ROHS3PEAKUncategorisedD3232T
TSSOP-16UncategorisedSilicoreTPAFE51716H-TS3R
TSSOP-16-40℃~+125℃ 0.5LSB 1 16 1LSB 1MHz 4.75V~5.25V 90dB Bipolar input External、Built-in External、Built-in SAR SPI Support Yes TSSOP-16 Analog to Digital Converters (ADC) ROHS3PEAKUncategorisedCS5799
TSSOP-16-40℃~+105℃ 2.4199MHz~2.4952MHz、2.4576MHz 2.8V~5.5V 24 3.125Hz 3.125Hz、6.4kHz 6 600nA Built-in Built-in SPI Sigma-Delta Support Yes TSSOP-16 Analog to Digital Converters (ADC) ROHSCooperationUncategorisedAD5668BRUZ-2REEL7
TSSOP-16-40℃~+105℃ 16 16LSB 2.7V~5.5V 400nA 4us 8 SPI Voltage Buffer TSSOP-16 Digital to Analog Converters (DAC) ROHSAnalog DevicesUncategorisedCS5793
TSSOP-16UncategorisedCooperationADC1283IPT
TSSOP-16-40℃~+125℃ 1.2LSB 12 2.7V~5.5V 50kHz 640uA 73dB 8 800kHz~3.2MHz Built-in External Multiplexers、Synchronous triggering No Not supported SAR SPI TSSOP-16 Analog to Digital Converters (ADC) ROHSSTMicroelectronicsUncategorisedADC78H90CIMTX
TSSOP-16-40℃~+85℃ 12 1LSB 2.7V~5.25V 200nA 500kHz 50kHz~8MHz 70.8dB 8 Multiplexers No SAR SPI TSSOP-16 Analog to Digital Converters (ADC) ROHSTexas InstrumentsUncategorised
Questions
Is there a KiCad symbol and footprint for the SC18IS602B?
Yes. The symbol is Logic:SC18IS602B and the footprint Package_SO:TSSOP-16_4.4x5mm_P0.65mm, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the SC18IS602B?
TSSOP16, with 16 pins. Its footprint is drawn on this page.
What can replace the SC18IS602B?
Parts like it in the library: the TPC116S8-TR by 3PEAK, the D3232T by Silicore, the TPAFE51716H-TS3R by 3PEAK and the CS5799 by Cooperation. Check their datasheets: a part that fits the footprint may still differ in its ratings.
Which open-source boards use the SC18IS602B?
6 boards in 6 repositories on GitHub; the most starred are listed on this page, with their KiCad files.