Skip to the content
LGA-113(12.1x11.1)

NRF9151-LACA-R

Nordic SemiconExtended

23dBm LGA-113(12.1x11.1) RF Modules ROHS

Part id
nordic-semicon/NRF9151-LACA-R
Category
RF Modules
Package
LGA-113(12.1x11.1)
Pins
113
In stock
0 at JLCPCB (C42236596)
Used on
4 open-source boards

Overview

The NRF9151-LACA-R is a RF Module made by Nordic Semicon in a LGA-113(12.1x11.1) package with 113 pins. 23dBm LGA-113(12.1x11.1) RF Modules ROHS.

JLCPCB lists it (part C42236596). 4 open-source boards in 3 repositories on GitHub use it.

Symbol

The library has no symbol for this part yet.

Footprint

The library has no footprint for this part yet.

From the datasheet

13
Supply, least
3 V · VDD, recommended operating min · p. 525
Supply, most
5.5 V · VDD, recommended operating max · p. 525
Supply, least
1.7 V · VDD_GPIO, recommended operating min · p. 525
Supply, most
3.6 V · VDD_GPIO, recommended operating max · p. 525
Supply, absolute maximum
5.5 V · VDD, absolute max · p. 526
Supply, absolute maximum
3.9 V · VDD_GPIO, absolute max · p. 526
Works from
-40 °C · Operating ambient temperature min · p. 525
Works up to
85 °C · Operating ambient temperature max · p. 525
Takes at most
240 mA · VDD, typical Cat-NB1 B20 RRC average at 23 dBm, BPSK, TX 80%, RX 10% · p. 65
Takes asleep
150 nA · VDD, typical System Disabled, ENABLE and VDD_GPIO grounded · p. 62
Takes asleep
1.4 µA · VDD, typical MCU off, modem off, wake on GPIO and reset · p. 62
Takes asleep
2.7 µA · VDD, typical Cat-M1/Cat-NB1 PSM floor current · p. 65
Takes working
47 mA · typical DECT NR+ reception, minimum latency mode, received signal -90 dBm · p. 66

What it is and has

14
Flash memory
1 MB · p. 2
RAM
256 KB low leakage RAM · p. 2
SPI
Up to four controller/targets with EasyDMA · p. 2
I2C
Up to four compatible two-wire controller/targets with EasyDMA · p. 2
UART
Up to four, CTS/RTS, with EasyDMA · p. 2
I2S
With EasyDMA · p. 2
PDM
Digital microphone interface with EasyDMA · p. 2
PWM
Four units with EasyDMA · p. 2
ADC
12-bit, 200 ksps, eight configurable channels with programmable gain, EasyDMA · p. 2
Timers
Three 32-bit timers with counter mode · p. 2
RTC
Two real-time counters · p. 2
GPIO
32 general purpose I/O pins · p. 2
Clock sources
Integrated · p. 2
Package
LGA, 12.1x11.1x1.2 mm · p. 2

Around it

2
res 100 kΩ size range
between COEX2 and GND; External pull-down required when using COEX2. · p. 426
other UICC-compatible ESD protection device
between LTE modem UICC interface and removable SIM card connector; Required between the removable card and LTE modem to protect against ESD from the connector. · p. 426

Specifications

242
ParameterConditionsAs printedPage
Number of times a 32-bit word can be written before erase nWRITEmax 236
Erase cycles per page nENDURANCEmin 1000036
Time to write one 32-bit word tWRITEmax 43 us36
Time to erase one page tERASEPAGEmax 87 ms36
Time to erase all flash tERASEALLmax 173 ms36
Setup time for one partial erase tERASEPAGEPARTIAL,setupmax 1.08 ms36
I-Code cache size SizeICODEtyp 2048 Bytes36
Time from OFF to CPU execute tOFF2ONtyp 73 · max 92 us55
Time from WFE to CPU execute tWFE2CPUtyp 70 · max 90 us55
Time from WFI to CPU execute tWFI2CPUtyp 69 · max 90 us55
Time from HW event to PPI event in constant latency System ON mode tEVTSET,CL1typ 0.1 · max 0.1 us55
Time from HW event to PPI event in low power System ON mode tEVTSET,CL0typ 0.1 · max 0.7 us55
LTE modem typical startup time. Time from application core powering up the modem until the modem is ready to receive the first AT command. tLTEMODEM,TYPmax 200 ms55
LTE modem worst case startup time. Time from application core powering up the modem until the modem is ready to receive the first AT command, with modem firmware variable elements included. tLTEMODEM,WORSTCASEmax 250 ms55
LTE modem startup time after modem FOTA update. Time from application core powering up the modem after a modem FOTA update until the modem is ready to receive the first AT command. tLTEMODEM,FOTAmax 7.5 s55
LTE modem startup time after a rejected modem FOTA update. Time from application core powering up the modem after a rejected modem FOTA update until the modem is ready to receive the first AT command. Modem will revert back to original firmware image. tLTEMODEM,FOTAREJECTmax 90 s55
LTE modem typical shutdown time. Time from application core calling bsd_shutdown command until bsd_shutdown returns. tLTEMODEM,STOP,TYPmax 1.6 s55
LTE modem worst case shutdown time. Time from application core calling bsd_shutdown command until bsd_shutdown returns, including modem firmware variable elements. tLTEMODEM,STOP,WORSTCASEmax 79 s55
Brownout reset voltage threshold. VBORtyp 2.8 V55
Voltage threshold at which the device enters power-on reset (POR) when VDD is ramping up. VPORmax 3 V55
Hold time for reset pin when doing a pin reset tHOLDRESETmin 5 us60
Value of the internal pull-up resistor RPULL-UPtyp 13 kΩ60
ENABLE and VDD_GPIO pins grounded ISYSTEM_DISABLEDVDD = 3.7 V, 25 °Ctyp 150 nA62
MCU off, modem off, wake on GPIO and reset IMCUOFF0VDD = 3.7 V, 25 °C; no RAM retentiontyp 1.4 uA62
MCU on IDLE, modem off, RTC off IMCUON0VDD = 3.7 V, 25 °C; no RAM retentiontyp 1.8 uA62
MCU on IDLE, modem off, RTC on IMCUON1VDD = 3.7 V, 25 °C; no RAM retentiontyp 2.2 uA62
MCU on IDLE, modem off, wake on GPIOTE input (event mode), Constant latency System ON mode IMCUON2VDD = 3.7 V, 25 °C; no RAM retentiontyp 600 uA62
MCU on IDLE, modem off, wake on GPIOTE input (event mode), Low power System ON mode IMCUON3VDD = 3.7 V, 25 °C; no RAM retentiontyp 18 uA62
MCU on IDLE, modem off, wake on GPIOTE input (port event) IMCUON4VDD = 3.7 V, 25 °C; no RAM retentiontyp 1.8 uA62
RAM retention leakage current of a 32kB block IRAMVDD = 3.7 V, 25 °Ctyp 0.1 uA62
CPU running CoreMark @64 MHz from flash, clock = HFINT, cache enabled ICPU0_FLASHVDD = 3.7 V, 25 °Ctyp 2.7 mA62
CoreMark per mA, executing from flash, CoreMark=247 ICOREMARK_PER_MA_FLASHVDD = 3.7 V, 25 °Ctyp 91 CoreMark/mA62
CPU running CoreMark @64 MHz from RAM, clock = HFINT ICPU0_RAMVDD = 3.7 V, 25 °Ctyp 2.1 mA62
CoreMark per mA, executing from RAM, CoreMark=239 ICOREMARK_PER_MA_RAMVDD = 3.7 V, 25 °Ctyp 114 CoreMark/mA62
I2S transferring data left-channel (mono) @ 16 bit x 16 kHz II2S0CONFIG.MCKFREQ = 32MDIV8, CONFIG.RATIO = 256X, Clock = HFINT; VDD = 3.7 V, 25 °Ctyp 600 uA62
I2S transferring data left-channel (mono) @ 16 bit x 16 kHz II2S1CONFIG.MCKFREQ = 32MDIV8, CONFIG.RATIO = 256X, Clock = HFXO; VDD = 3.7 V, 25 °Ctyp 1620 uA62
TWIM running @ 100 kbps, Clock=HFINT ITWIM_100VDD = 3.7 V, 25 °Ctyp 590 uA64
TWIM running @ 400 kbps, Clock = HFINT ITWIM_400VDD = 3.7 V, 25 °Ctyp 590 uA64
TWIM running @ 100 kbps, Clock = HFXO ITWIM_100XOVDD = 3.7 V, 25 °Ctyp 1600 uA64
TWIM running @ 400 kbps, Clock = HFXO ITWIM_400XOVDD = 3.7 V, 25 °Ctyp 1610 uA64
TWIS transferring data @ 100 kbps, Clock=HFINT ITWIS,RUN_100VDD = 3.7 V, 25 °Ctyp 590 uA64
TWIS transferring data @ 400 kbps, Clock=HFINT ITWIS1,RUN_400VDD = 3.7 V, 25 °Ctyp 510 uA64
TWIS transferring data @ 100 kbps, Clock = HFXO ITWIS,RUN_100XOVDD = 3.7 V, 25 °Ctyp 1480 uA64
TWIS transferring data @ 400 kbps, Clock = HFXO ITWIS,RUN_400XOVDD = 3.7 V, 25 °Ctyp 1370 uA64
UARTE transferring data @ 1Mbps IUARTE,1MVDD = 3.7 V, 25 °Ctyp 700 uA64
UARTE transferring data @ 115200 bps IUARTE,115KVDD = 3.7 V, 25 °Ctyp 510 uA64
WDT started IWDTVDD = 3.7 V, 25 °Ctyp 2.5 uA64
PSM floor current IPSMCat-M1 and Cat-NB1; B13; VDD = 3.7 V, 25 °Ctyp 2.7 uA65
PSM floor current IPSMCat-M1 and Cat-NB1; B20; VDD = 3.7 V, 25 °Ctyp 2.7 uA65
PSM floor current IPSMCat-M1 and Cat-NB1; B3; VDD = 3.7 V, 25 °Ctyp 2.7 uA65
PSM floor current IPSMCat-M1 and Cat-NB1; B4; VDD = 3.7 V, 25 °Ctyp 2.7 uA65
PSM TAU event energy EPSM_TAUCat-M1; B13; Pout 23 dBm, QPSK, resource blocks 6, TBS index 9, UICC includedtyp 91 mJ65
PSM TAU event energy EPSM_TAUCat-M1; B20; Pout 23 dBm, QPSK, resource blocks 6, TBS index 9, UICC includedtyp 97 mJ65
PSM TAU event energy EPSM_TAUCat-M1; B3; Pout 23 dBm, QPSK, resource blocks 6, TBS index 9, UICC includedtyp 95 mJ65
PSM TAU event energy EPSM_TAUCat-M1; B4; Pout 23 dBm, QPSK, resource blocks 6, TBS index 9, UICC includedtyp 94 mJ65
PSM TAU event duration TPSM_TAUCat-M1; B13; Pout 23 dBm, QPSK, resource blocks 6, TBS index 9, UICC includedtyp 1 s65
PSM TAU event duration TPSM_TAUCat-M1; B20; Pout 23 dBm, QPSK, resource blocks 6, TBS index 9, UICC includedtyp 1 s65
PSM TAU event duration TPSM_TAUCat-M1; B3; Pout 23 dBm, QPSK, resource blocks 6, TBS index 9, UICC includedtyp 1 s65
PSM TAU event duration TPSM_TAUCat-M1; B4; Pout 23 dBm, QPSK, resource blocks 6, TBS index 9, UICC includedtyp 1 s65
PSM TAU event energy EPSM_TAUCat-NB1; B13; Pout 23 dBm, QPSK, UICC included; UL: 12SC, MCS Index 5 Resource Units 1, Repetitions 1; DL: 12SC, MCS Index 6, Subframes 3, Repetitions 1typ 343 mJ65
PSM TAU event energy EPSM_TAUCat-NB1; B20; Pout 23 dBm, QPSK, UICC included; UL: 12SC, MCS Index 5 Resource Units 1, Repetitions 1; DL: 12SC, MCS Index 6, Subframes 3, Repetitions 1typ 376 mJ65
PSM TAU event energy EPSM_TAUCat-NB1; B3; Pout 23 dBm, QPSK, UICC included; UL: 12SC, MCS Index 5 Resource Units 1, Repetitions 1; DL: 12SC, MCS Index 6, Subframes 3, Repetitions 1typ 357 mJ65
PSM TAU event energy EPSM_TAUCat-NB1; B4; Pout 23 dBm, QPSK, UICC included; UL: 12SC, MCS Index 5 Resource Units 1, Repetitions 1; DL: 12SC, MCS Index 6, Subframes 3, Repetitions 1typ 347 mJ65
PSM TAU event duration TPSM_TAUCat-NB1; B13; Pout 23 dBm, QPSK, UICC included; UL: 12SC, MCS Index 5 Resource Units 1, Repetitions 1; DL: 12SC, MCS Index 6, Subframes 3, Repetitions 1typ 2.3 s65
PSM TAU event duration TPSM_TAUCat-NB1; B20; Pout 23 dBm, QPSK, UICC included; UL: 12SC, MCS Index 5 Resource Units 1, Repetitions 1; DL: 12SC, MCS Index 6, Subframes 3, Repetitions 1typ 2.4 s65
PSM TAU event duration TPSM_TAUCat-NB1; B3; Pout 23 dBm, QPSK, UICC included; UL: 12SC, MCS Index 5 Resource Units 1, Repetitions 1; DL: 12SC, MCS Index 6, Subframes 3, Repetitions 1typ 2.3 s65
PSM TAU event duration TPSM_TAUCat-NB1; B4; Pout 23 dBm, QPSK, UICC included; UL: 12SC, MCS Index 5 Resource Units 1, Repetitions 1; DL: 12SC, MCS Index 6, Subframes 3, Repetitions 1typ 2.4 s65
eDRX average current, 81.92 s, one PO/PTW, PTW = 2.56 s IEDRXCat-M1; B13typ 18 uA65
eDRX average current, 81.92 s, one PO/PTW, PTW = 2.56 s IEDRXCat-M1; B3typ 18 uA65
Idle eDRX average current, 655 s, one PO/PTW, PTW = 2.56 s IIEDRXCat-M1; B13typ 5 uA65
Idle eDRX average current, 655 s, one PO/PTW, PTW = 2.56 s IIEDRXCat-M1; B3typ 5 uA65
Pout 0 dBm, QPSK, 1RB, 5MHz, RMC settings as per 3GPP TS 36.521-1 Annex A.2 IRMC_0DBMCat-M1 RRC; B13typ 45 mA65
Pout 0 dBm, QPSK, 1RB, 5MHz, RMC settings as per 3GPP TS 36.521-1 Annex A.2 IRMC_0DBMCat-M1 RRC; B20typ 45 mA65
Pout 0 dBm, QPSK, 1RB, 5MHz, RMC settings as per 3GPP TS 36.521-1 Annex A.2 IRMC_0DBMCat-M1 RRC; B3typ 45 mA65
Pout 0 dBm, QPSK, 1RB, 5MHz, RMC settings as per 3GPP TS 36.521-1 Annex A.2 IRMC_0DBMCat-M1 RRC; B4typ 45 mA65
Pout 10 dBm, QPSK, 1RB, 5MHz, RMC settings as per 3GPP TS 36.521-1 Annex A.2 IRMC_10DBMCat-M1 RRC; B13typ 50 mA65
Pout 10 dBm, QPSK, 1RB, 5MHz, RMC settings as per 3GPP TS 36.521-1 Annex A.2 IRMC_10DBMCat-M1 RRC; B20typ 50 mA65
Pout 10 dBm, QPSK, 1RB, 5MHz, RMC settings as per 3GPP TS 36.521-1 Annex A.2 IRMC_10DBMCat-M1 RRC; B3typ 55 mA65
Pout 10 dBm, QPSK, 1RB, 5MHz, RMC settings as per 3GPP TS 36.521-1 Annex A.2 IRMC_10DBMCat-M1 RRC; B4typ 55 mA65
Pout 23 dBm, QPSK, 1RB, 5MHz, RMC settings as per 3GPP TS 36.521-1 Annex A.2 IRMC_23DBMCat-M1 RRC; B13typ 115 mA65
Pout 23 dBm, QPSK, 1RB, 5MHz, RMC settings as per 3GPP TS 36.521-1 Annex A.2 IRMC_23DBMCat-M1 RRC; B20typ 125 mA65
Pout 23 dBm, QPSK, 1RB, 5MHz, RMC settings as per 3GPP TS 36.521-1 Annex A.2 IRMC_23DBMCat-M1 RRC; B3typ 120 mA65
Pout 23 dBm, QPSK, 1RB, 5MHz, RMC settings as per 3GPP TS 36.521-1 Annex A.2 IRMC_23DBMCat-M1 RRC; B4typ 120 mA65
eDRX average current, 81.92 s, one PO/PTW, PTW = 2.56 s IEDRXCat-NB1; B13typ 32 uA65
eDRX average current, 81.92 s, one PO/PTW, PTW = 2.56 s IEDRXCat-NB1; B3typ 33 uA65
Idle eDRX average current, 655 s, one PO/PTW, PTW = 2.56 s IIEDRXCat-NB1; B13typ 7 uA65
Idle eDRX average current, 655 s, one PO/PTW, PTW = 2.56 s IIEDRXCat-NB1; B3typ 7 uA65
Pout 0 dBm, QPSK, 1SC, 15 kHz, TX 33% RX 33%, RMC settings as per 3GPP TS 36.101 Annex A.2.4 IRMC_0DBMCat-NB1 RRC; B13typ 30 mA65
Pout 0 dBm, QPSK, 1SC, 15 kHz, TX 33% RX 33%, RMC settings as per 3GPP TS 36.101 Annex A.2.4 IRMC_0DBMCat-NB1 RRC; B20typ 30 mA65
Pout 0 dBm, QPSK, 1SC, 15 kHz, TX 33% RX 33%, RMC settings as per 3GPP TS 36.101 Annex A.2.4 IRMC_0DBMCat-NB1 RRC; B3typ 30 mA65
Pout 0 dBm, QPSK, 1SC, 15 kHz, TX 33% RX 33%, RMC settings as per 3GPP TS 36.101 Annex A.2.4 IRMC_0DBMCat-NB1 RRC; B4typ 35 mA65
Pout 10 dBm, QPSK, 1SC, 15 kHz, TX 33% RX 33%, RMC settings as per 3GPP TS 36.101 Annex A.2.4 IRMC_10DBMCat-NB1 RRC; B13typ 40 mA65
Pout 10 dBm, QPSK, 1SC, 15 kHz, TX 33% RX 33%, RMC settings as per 3GPP TS 36.101 Annex A.2.4 IRMC_10DBMCat-NB1 RRC; B20typ 40 mA65
Pout 10 dBm, QPSK, 1SC, 15 kHz, TX 33% RX 33%, RMC settings as per 3GPP TS 36.101 Annex A.2.4 IRMC_10DBMCat-NB1 RRC; B3typ 40 mA65
Pout 10 dBm, QPSK, 1SC, 15 kHz, TX 33% RX 33%, RMC settings as per 3GPP TS 36.101 Annex A.2.4 IRMC_10DBMCat-NB1 RRC; B4typ 45 mA65
Pout 23 dBm, QPSK, 1SC, 15 kHz, TX 33% RX 33%, RMC settings as per 3GPP TS 36.101 Annex A.2.4 IRMC_23DBMCat-NB1 RRC; B13typ 100 mA65
Pout 23 dBm, QPSK, 1SC, 15 kHz, TX 33% RX 33%, RMC settings as per 3GPP TS 36.101 Annex A.2.4 IRMC_23DBMCat-NB1 RRC; B20typ 120 mA65
Pout 23 dBm, QPSK, 1SC, 15 kHz, TX 33% RX 33%, RMC settings as per 3GPP TS 36.101 Annex A.2.4 IRMC_23DBMCat-NB1 RRC; B3typ 110 mA65
Pout 23 dBm, QPSK, 1SC, 15 kHz, TX 33% RX 33%, RMC settings as per 3GPP TS 36.101 Annex A.2.4 IRMC_23DBMCat-NB1 RRC; B4typ 115 mA65
Pout 0 dBm, BPSK, 1SC, 3.75 kHz, TX 80% RX 10%, RMC settings as per 3GPP TS 36.101 Annex A.2.4 IRMC_0DBMCat-NB1 RRC; B13typ 50 mA65
Pout 0 dBm, BPSK, 1SC, 3.75 kHz, TX 80% RX 10%, RMC settings as per 3GPP TS 36.101 Annex A.2.4 IRMC_0DBMCat-NB1 RRC; B20typ 50 mA65
Pout 0 dBm, BPSK, 1SC, 3.75 kHz, TX 80% RX 10%, RMC settings as per 3GPP TS 36.101 Annex A.2.4 IRMC_0DBMCat-NB1 RRC; B3typ 55 mA65
Pout 0 dBm, BPSK, 1SC, 3.75 kHz, TX 80% RX 10%, RMC settings as per 3GPP TS 36.101 Annex A.2.4 IRMC_0DBMCat-NB1 RRC; B4typ 55 mA65
Pout 10 dBm, BPSK, 1SC, 3.75 kHz, TX 80% RX 10%, RMC settings as per 3GPP TS 36.101 Annex A.2.4 IRMC_10DBMCat-NB1 RRC; B13typ 70 mA65
Pout 10 dBm, BPSK, 1SC, 3.75 kHz, TX 80% RX 10%, RMC settings as per 3GPP TS 36.101 Annex A.2.4 IRMC_10DBMCat-NB1 RRC; B20typ 70 mA65
Pout 10 dBm, BPSK, 1SC, 3.75 kHz, TX 80% RX 10%, RMC settings as per 3GPP TS 36.101 Annex A.2.4 IRMC_10DBMCat-NB1 RRC; B3typ 80 mA65
Pout 10 dBm, BPSK, 1SC, 3.75 kHz, TX 80% RX 10%, RMC settings as per 3GPP TS 36.101 Annex A.2.4 IRMC_10DBMCat-NB1 RRC; B4typ 80 mA65
Pout 23 dBm, BPSK, 1SC, 3.75 kHz, TX 80% RX 10%, RMC settings as per 3GPP TS 36.101 Annex A.2.4 IRMC_23DBMCat-NB1 RRC; B13typ 215 mA65
Pout 23 dBm, BPSK, 1SC, 3.75 kHz, TX 80% RX 10%, RMC settings as per 3GPP TS 36.101 Annex A.2.4 IRMC_23DBMCat-NB1 RRC; B20typ 240 mA65
Pout 23 dBm, BPSK, 1SC, 3.75 kHz, TX 80% RX 10%, RMC settings as per 3GPP TS 36.101 Annex A.2.4 IRMC_23DBMCat-NB1 RRC; B3typ 235 mA65
Pout 23 dBm, BPSK, 1SC, 3.75 kHz, TX 80% RX 10%, RMC settings as per 3GPP TS 36.101 Annex A.2.4 IRMC_23DBMCat-NB1 RRC; B4typ 230 mA65
Battery input voltage VDDIncluding voltage drop, ripple and spikes.min 3 · typ 3.7 · max 5.5 V525
GPIO input voltage VDD_GPIOmin 1.7 · max 3.6 V525
MAGPIO high level voltage MAGPIOHSupply from internal LDOmin 1.7 · typ 1.8 · max 1.9 V525
VIO high level voltage VIOSupply from internal LDOmin 1.7 · typ 1.8 · max 1.9 V525
Operating temperature TAmin -40 · typ 25 · max 85 °C525
SIMIF output high level voltage SIMIFSupply from internal LDOmin 1.7 · typ 1.8 · max 1.9 V525
VDD VDDAbsolute maximum ratingsmin -0.3 · max 5.5 V526
VDD_GPIO VDD_GPIOAbsolute maximum ratingsmin -0.3 · max 3.9 V526
SIM_1V8 SIM_1V8Absolute maximum ratingsmin 1.65 · max 1.95 V526
VSS VSSAbsolute maximum ratingsmax 0 V526
VI/O, VDD_GPIO ≤ 3.6 V VI/OAbsolute maximum ratings; VDD_GPIO ≤ 3.6 Vmin -0.3 V526
VI/O, VDD_GPIO > 3.6 V VI/OAbsolute maximum ratings; VDD_GPIO > 3.6 Vmin -0.3 · max 3.9 V526
ANT antenna input levelAbsolute maximum ratingsmax 10 dBm526
GPS antenna input levelAbsolute maximum ratings; LNA turned on, max gainmax -15 dBm526
Storage temperatureAbsolute maximum ratings; LGA packagemin -40 · max 95 °C527
MSLMoisture Sensitivity Level; LGA packagemax 3527
ESD HBM AUXAUX pin Human Body Model; AUX pin is intended for production testmax 500 V527
ESD HBMHuman Body Model; AUX pin excludedmax 1.5 kV527
ESD CDMCharged Device Modelmax 250 V527
Endurancemin 10000 Write/ erase cycles527
Retentionat 85°Cmin 10 y527
ENABLE and VDD_GPIO pins grounded ISYSTEM_DISABLEDtyp 150 nA62
MCU off, modem off, wake on GPIO and reset IMCUOFF0typ 1.4 uA62
MCU on IDLE, modem off, RTC off IMCUON0typ 1.8 uA62
MCU on IDLE, modem off, RTC on IMCUON1typ 2.2 uA62
MCU on IDLE, modem off, wake on GPIOTE input (event mode), Constant latency System ON mode IMCUON2typ 600 uA62
MCU on IDLE, modem off, wake on GPIOTE input (event mode), Low power System ON mode IMCUON3typ 18 uA62
MCU on IDLE, modem off, wake on GPIOTE input (port event) IMCUON4typ 1.8 uA62
RAM retention leakage current of a 32kB block IRAMtyp 0.1 uA62
CPU running CoreMark @64 MHz from flash, clock = HFINT, cache enabled ICPU0_FLASHtyp 2.7 mA62
CoreMark per mA, executing from flash, CoreMark=247 ICOREMARK_PER_MA_FLASHtyp 91 CoreMark/mA62
CPU running CoreMark @64 MHz from RAM, clock = HFINT ICPU0_RAMtyp 2.1 mA62
CoreMark per mA, executing from RAM, CoreMark=239 ICOREMARK_PER_MA_RAMtyp 114 CoreMark/mA62
I2S transferring data left-channel (mono) @ 16 bit x 16 kHz II2S0(CONFIG.MCKFREQ = 32MDIV8, CONFIG.RATIO = 256X), Clock = HFINTtyp 600 uA62
I2S transferring data left-channel (mono) @ 16 bit x 16 kHz II2S1(CONFIG.MCKFREQ = 32MDIV8, CONFIG.RATIO = 256X), Clock = HFXOtyp 1620 uA62
PDM receiving and processing data 16KHz IPDMFREQ = 1.28MHz, MODE.OPERATION = monotyp 620 uA63
PDM receiving and processing data 16KHz IPDMFREQ = 1.28MHz, MODE.OPERATION = mono, clock HFXOtyp 1630 uA63
PWM running @ 125 kHz, fixed duty cycle IPWM0typ 510 uA63
PWM running @ 16 MHz, fixed duty cycle IPWM1typ 680 uA63
SAADC sampling @ 16 ksps, with high accuracy clock HFXO, acquisition time = 20 us ISAADC_HFXOtyp 1550 uA63
SAADC sampling @ 16 ksps, with low accuracy clock HFINT, acquisition time = 20 us ISAADC_HFINTtyp 540 uA63
TIMER running @ 1 MHz ITIMER0typ 390 uA63
TIMER running @ 16 MHz ITIMER1typ 440 uA63
SPIM transferring data @ 2 Mbps, Clock = HFINT ISPIM0typ 610 uA63
SPIM transferring data @ 2 Mbps, Clock = HFXO ISPIM1typ 1620 uA63
SPIM transferring data @ 8 Mbps, Clock = HFINT ISPIM2typ 640 uA63
SPIM transferring data @ 8 Mbps, Clock = HFXO ISPIM3typ 1660 uA63
SPIS receiving data @ 2 Mbps, Clock=HFINT ISPIS_2Mtyp 500 uA63
SPIS receiving data @ 2 Mbps, Clock=HFXO ISPIS_2MXOtyp 1510 uA63
SPIS receiving data @ 8 Mbps, Clock=HFINT ISPIS_8Mtyp 510 uA63
SPIS receiving data @ 8 Mbps, Clock=HFXO ISPIS_8MXOtyp 1520 uA63
TWIM running @ 100 kbps, Clock=HFINT ITWIM_100typ 590 uA64
TWIM running @ 400 kbps, Clock = HFINT ITWIM_400typ 590 uA64
TWIM running @ 100 kbps, Clock = HFXO ITWIM_100XOtyp 1600 uA64
TWIM running @ 400 kbps, Clock = HFXO ITWIM_400XOtyp 1610 uA64
TWIS transferring data @ 100 kbps, Clock=HFINT ITWIS,RUN_100typ 590 uA64
TWIS transferring data @ 400 kbps, Clock=HFINT ITWIS1,RUN_400typ 510 uA64
TWIS transferring data @ 100 kbps, Clock = HFXO ITWIS,RUN_100XOtyp 1480 uA64
TWIS transferring data @ 400 kbps, Clock = HFXO ITWIS,RUN_400XOtyp 1370 uA64
UARTE transferring data @ 1Mbps IUARTE,1Mtyp 700 uA64
UARTE transferring data @ 115200 bps IUARTE,115Ktyp 510 uA64
WDT started IWDTtyp 2.5 uA64
PSM floor current IPSMCat-M1 and Cat-NB1; B13, B20, B3, B4typ 2.7 uA65
PSM TAU event duration TPSM_TAUCat-M1; B13, B20, B3, B4; Pout 23 dBm, QPSK, resource blocks 6, TBS index 9, UICC includedtyp 1 s65
PSM TAU event energy EPSM_TAUCat-NB1; B13; Pout 23 dBm, QPSK, UICC included; UL: 12SC, MCS Index 5 Resource Units 1, Repetitions 1; DL, 12SC, MCS Index 6, Subframes 3, Repetitions 1typ 343 mJ65
PSM TAU event energy EPSM_TAUCat-NB1; B20; Pout 23 dBm, QPSK, UICC included; UL: 12SC, MCS Index 5 Resource Units 1, Repetitions 1; DL, 12SC, MCS Index 6, Subframes 3, Repetitions 1typ 376 mJ65
PSM TAU event energy EPSM_TAUCat-NB1; B3; Pout 23 dBm, QPSK, UICC included; UL: 12SC, MCS Index 5 Resource Units 1, Repetitions 1; DL, 12SC, MCS Index 6, Subframes 3, Repetitions 1typ 357 mJ65
PSM TAU event energy EPSM_TAUCat-NB1; B4; Pout 23 dBm, QPSK, UICC included; UL: 12SC, MCS Index 5 Resource Units 1, Repetitions 1; DL, 12SC, MCS Index 6, Subframes 3, Repetitions 1typ 347 mJ65
PSM TAU event duration TPSM_TAUCat-NB1; B13, B3; Pout 23 dBm, QPSK, UICC included; UL: 12SC, MCS Index 5 Resource Units 1, Repetitions 1; DL, 12SC, MCS Index 6, Subframes 3, Repetitions 1typ 2.3 s65
PSM TAU event duration TPSM_TAUCat-NB1; B20, B4; Pout 23 dBm, QPSK, UICC included; UL: 12SC, MCS Index 5 Resource Units 1, Repetitions 1; DL, 12SC, MCS Index 6, Subframes 3, Repetitions 1typ 2.4 s65
eDRX average current, 81.92 s, one PO/PTW, PTW = 2.56 s IEDRXRRC mode, Cat-M1; B13, B3typ 18 uA65
Idle eDRX average current, 655 s, one PO/PTW, PTW = 2.56 s IIEDRXRRC mode, Cat-M1; B13, B3typ 5 uA65
Average current consumption, radio resource control (RRC) mode, Cat-M1 IRMC_0DBMB13, B20, B3, B4; Pout 0 dBm, QPSK, 1RB, 5MHz, RMC settings as per 3GPP TS 36.521-1 Annex A.2typ 45 mA65
Average current consumption, radio resource control (RRC) mode, Cat-M1 IRMC_10DBMB13, B20; Pout 10 dBm, QPSK, 1RB, 5MHz, RMC settings as per 3GPP TS 36.521-1 Annex A.2typ 50 mA65
Average current consumption, radio resource control (RRC) mode, Cat-M1 IRMC_10DBMB3, B4; Pout 10 dBm, QPSK, 1RB, 5MHz, RMC settings as per 3GPP TS 36.521-1 Annex A.2typ 55 mA65
Average current consumption, radio resource control (RRC) mode, Cat-M1 IRMC_23DBMB13; Pout 23 dBm, QPSK, 1RB, 5MHz, RMC settings as per 3GPP TS 36.521-1 Annex A.2typ 115 mA65
Average current consumption, radio resource control (RRC) mode, Cat-M1 IRMC_23DBMB20; Pout 23 dBm, QPSK, 1RB, 5MHz, RMC settings as per 3GPP TS 36.521-1 Annex A.2typ 125 mA65
Average current consumption, radio resource control (RRC) mode, Cat-M1 IRMC_23DBMB3, B4; Pout 23 dBm, QPSK, 1RB, 5MHz, RMC settings as per 3GPP TS 36.521-1 Annex A.2typ 120 mA65
eDRX average current, 81.92 s, one PO/PTW, PTW = 2.56 s IEDRXRRC mode, Cat-NB1; B13typ 32 uA65
eDRX average current, 81.92 s, one PO/PTW, PTW = 2.56 s IEDRXRRC mode, Cat-NB1; B3typ 33 uA65
Idle eDRX average current, 655 s, one PO/PTW, PTW = 2.56 s IIEDRXRRC mode, Cat-NB1; B13, B3typ 7 uA65
Average current consumption, radio resource control (RRC) mode, Cat-NB1 IRMC_0DBMB13, B20, B3; Pout 0 dBm, QPSK, 1SC, 15 kHz, TX 33% RX 33%, RMC settings as per 3GPP TS 36.101 Annex A.2.4typ 30 mA65
Average current consumption, radio resource control (RRC) mode, Cat-NB1 IRMC_0DBMB4; Pout 0 dBm, QPSK, 1SC, 15 kHz, TX 33% RX 33%, RMC settings as per 3GPP TS 36.101 Annex A.2.4typ 35 mA65
Average current consumption, radio resource control (RRC) mode, Cat-NB1 IRMC_10DBMB13, B20, B3; Pout 10 dBm, QPSK, 1SC, 15 kHz, TX 33% RX 33%, RMC settings as per 3GPP TS 36.101 Annex A.2.4typ 40 mA65
Average current consumption, radio resource control (RRC) mode, Cat-NB1 IRMC_10DBMB4; Pout 10 dBm, QPSK, 1SC, 15 kHz, TX 33% RX 33%, RMC settings as per 3GPP TS 36.101 Annex A.2.4typ 45 mA65
Average current consumption, radio resource control (RRC) mode, Cat-NB1 IRMC_23DBMB13; Pout 23 dBm, QPSK, 1SC, 15 kHz, TX 33% RX 33%, RMC settings as per 3GPP TS 36.101 Annex A.2.4typ 100 mA65
Average current consumption, radio resource control (RRC) mode, Cat-NB1 IRMC_23DBMB20; Pout 23 dBm, QPSK, 1SC, 15 kHz, TX 33% RX 33%, RMC settings as per 3GPP TS 36.101 Annex A.2.4typ 120 mA65
Average current consumption, radio resource control (RRC) mode, Cat-NB1 IRMC_23DBMB3; Pout 23 dBm, QPSK, 1SC, 15 kHz, TX 33% RX 33%, RMC settings as per 3GPP TS 36.101 Annex A.2.4typ 110 mA65
Average current consumption, radio resource control (RRC) mode, Cat-NB1 IRMC_23DBMB4; Pout 23 dBm, QPSK, 1SC, 15 kHz, TX 33% RX 33%, RMC settings as per 3GPP TS 36.101 Annex A.2.4typ 115 mA65
Average current consumption, radio resource control (RRC) mode, Cat-NB1 IRMC_0DBMB13, B20; Pout 0 dBm, BPSK, 1SC, 3.75 kHz, TX 80% RX 10%, RMC settings as per 3GPP TS 36.101 Annex A.2.4typ 50 mA65
Average current consumption, radio resource control (RRC) mode, Cat-NB1 IRMC_0DBMB3, B4; Pout 0 dBm, BPSK, 1SC, 3.75 kHz, TX 80% RX 10%, RMC settings as per 3GPP TS 36.101 Annex A.2.4typ 55 mA65
Average current consumption, radio resource control (RRC) mode, Cat-NB1 IRMC_10DBMB13, B20; Pout 10 dBm, BPSK, 1SC, 3.75 kHz, TX 80% RX 10%, RMC settings as per 3GPP TS 36.101 Annex A.2.4typ 70 mA65
Average current consumption, radio resource control (RRC) mode, Cat-NB1 IRMC_10DBMB3, B4; Pout 10 dBm, BPSK, 1SC, 3.75 kHz, TX 80% RX 10%, RMC settings as per 3GPP TS 36.101 Annex A.2.4typ 80 mA65
Average current consumption, radio resource control (RRC) mode, Cat-NB1 IRMC_23DBMB13; Pout 23 dBm, BPSK, 1SC, 3.75 kHz, TX 80% RX 10%, RMC settings as per 3GPP TS 36.101 Annex A.2.4typ 215 mA65
Average current consumption, radio resource control (RRC) mode, Cat-NB1 IRMC_23DBMB20; Pout 23 dBm, BPSK, 1SC, 3.75 kHz, TX 80% RX 10%, RMC settings as per 3GPP TS 36.101 Annex A.2.4typ 240 mA65
Average current consumption, radio resource control (RRC) mode, Cat-NB1 IRMC_23DBMB3; Pout 23 dBm, BPSK, 1SC, 3.75 kHz, TX 80% RX 10%, RMC settings as per 3GPP TS 36.101 Annex A.2.4typ 235 mA65
Average current consumption, radio resource control (RRC) mode, Cat-NB1 IRMC_23DBMB4; Pout 23 dBm, BPSK, 1SC, 3.75 kHz, TX 80% RX 10%, RMC settings as per 3GPP TS 36.101 Annex A.2.4typ 230 mA65
PSM TAU event energy EPSM_TAUCat-M1; B13; Pout 20 dBm, QPSK, resource blocks 6, TBS index 9, UICC includedtyp 84 mJ66
PSM TAU event energy EPSM_TAUCat-M1; B20, B3; Pout 20 dBm, QPSK, resource blocks 6, TBS index 9, UICC includedtyp 87 mJ66
PSM TAU event energy EPSM_TAUCat-M1; B4; Pout 20 dBm, QPSK, resource blocks 6, TBS index 9, UICC includedtyp 86 mJ66
PSM TAU event duration TPSM_TAUCat-M1; B13, B20, B3, B4; Pout 20 dBm, QPSK, resource blocks 6, TBS index 9, UICC includedtyp 1 s66
PSM TAU event energy EPSM_TAUCat-NB1; B13; Pout 20 dBm, QPSK, UICC included; UL: 12SC, MCS Index 5 Resource Units 1, Repetitions 1; DL, 12SC, MCS Index 6, Subframes 3, Repetitions 1typ 260 mJ66
PSM TAU event energy EPSM_TAUCat-NB1; B20; Pout 20 dBm, QPSK, UICC included; UL: 12SC, MCS Index 5 Resource Units 1, Repetitions 1; DL, 12SC, MCS Index 6, Subframes 3, Repetitions 1typ 276 mJ66
PSM TAU event energy EPSM_TAUCat-NB1; B3; Pout 20 dBm, QPSK, UICC included; UL: 12SC, MCS Index 5 Resource Units 1, Repetitions 1; DL, 12SC, MCS Index 6, Subframes 3, Repetitions 1typ 280 mJ66
PSM TAU event energy EPSM_TAUCat-NB1; B4; Pout 20 dBm, QPSK, UICC included; UL: 12SC, MCS Index 5 Resource Units 1, Repetitions 1; DL, 12SC, MCS Index 6, Subframes 3, Repetitions 1typ 290 mJ66
PSM TAU event duration TPSM_TAUCat-NB1; B13; Pout 20 dBm, QPSK, UICC included; UL: 12SC, MCS Index 5 Resource Units 1, Repetitions 1; DL, 12SC, MCS Index 6, Subframes 3, Repetitions 1typ 2.3 s66
PSM TAU event duration TPSM_TAUCat-NB1; B20, B3, B4; Pout 20 dBm, QPSK, UICC included; UL: 12SC, MCS Index 5 Resource Units 1, Repetitions 1; DL, 12SC, MCS Index 6, Subframes 3, Repetitions 1typ 2.4 s66
Average current consumption, radio resource control (RRC) mode, Cat-M1 IRMC_20DBMB13, B20, B3, B4; Pout 20 dBm, QPSK, 1RB, 5MHz, RMC settings as per 3GPP TS 36.521-1 Annex A.2typ 90 mA66
Average current consumption, radio resource control (RRC) mode, Cat-NB1 IRMC_20DBMB13; Pout 20 dBm, QPSK, 1SC, 15 kHz, TX 33% RX 33%, RMC settings as per 3GPP TS 36.101 Annex A.2.4typ 70 mA66
Average current consumption, radio resource control (RRC) mode, Cat-NB1 IRMC_20DBMB20; Pout 20 dBm, QPSK, 1SC, 15 kHz, TX 33% RX 33%, RMC settings as per 3GPP TS 36.101 Annex A.2.4typ 75 mA66
Average current consumption, radio resource control (RRC) mode, Cat-NB1 IRMC_20DBMB3, B4; Pout 20 dBm, QPSK, 1SC, 15 kHz, TX 33% RX 33%, RMC settings as per 3GPP TS 36.101 Annex A.2.4typ 80 mA66
Average current consumption, radio resource control (RRC) mode, Cat-NB1 IRMC_20DBMB13; Pout 20 dBm, BPSK, 1SC, 3.75 kHz, TX 80% RX 10%, RMC settings as per 3GPP TS 36.101 Annex A.2.4typ 145 mA66
Average current consumption, radio resource control (RRC) mode, Cat-NB1 IRMC_20DBMB20; Pout 20 dBm, BPSK, 1SC, 3.75 kHz, TX 80% RX 10%, RMC settings as per 3GPP TS 36.101 Annex A.2.4typ 150 mA66
Average current consumption, radio resource control (RRC) mode, Cat-NB1 IRMC_20DBMB3, B4; Pout 20 dBm, BPSK, 1SC, 3.75 kHz, TX 80% RX 10%, RMC settings as per 3GPP TS 36.101 Annex A.2.4typ 160 mA66
Average current during active transmission, nominal operating conditions ITX_PL13_LOW_LATENCYB1, B2, B9, B22; Minimum latency mode, any modulation, Power level 13 (19 dBm)typ 235 mA66
Average current during active reception, nominal operating conditions IRX_-90DBM_LOW_LATENCYB1, B2, B9, B22; Minimum latency mode, Received signal -90 dBmtyp 47 mA66
Average current during idle, nominal operating conditions IIDLE_LOW_LATENCYB1, B2, B9, B22; Minimum latency mode, modem waiting for TX or RX operationtyp 37 mA66
Continuous tracking, without power saving mode IGPS_CONTINUOUStyp 43.1 mA67
Continuous tracking, power saving mode IGPS_CONTINUOUS_PSMtyp 7.8 mA67
Periodic fix average current with A-GPS, one fix every 2 minutes IGPS_PERIODICIncluding LTE current consumptiontyp 0.5 mA67
Battery input voltage VDDIncluding voltage drop, ripple and spikes.; Nom. column recorded as typmin 3 · typ 3.7 · max 5.5 V525
MAGPIO high level voltage MAGPIOHSupply from internal LDO; Nom. column recorded as typmin 1.7 · typ 1.8 · max 1.9 V525
VIO high level voltage VIOSupply from internal LDO; Nom. column recorded as typmin 1.7 · typ 1.8 · max 1.9 V525
Operating temperature TANom. column recorded as typmin -40 · typ 25 · max 85 °C525
SIMIF output high level voltage SIMIFSupply from internal LDO; Nom. column recorded as typmin 1.7 · typ 1.8 · max 1.9 V525
VI/O, VDD_GPIO ≤ 3.6 V VI/OAbsolute maximum ratings; VDD_GPIO ≤ 3.6 V; maximum is VDD_GPIO + 0.3 V, continued on the next linemin -0.3 V526
MSLLGA package; Moisture Sensitivity Levelmax 3527
ESD HBM AUXLGA package; AUX pin Human Body Model; AUX pin is intended for production testmax 500 V527
ESD HBMLGA package; Human Body Model; AUX pin excludedmax 1.5 kV527
ESD CDMLGA package; Charged Device Modelmax 250 V527
Retention10 years at 85°Cmin 10 y527

Pins, by the datasheet

8
1 GND
Ground. · p. 518
2 P0.20
General purpose I/O; alternate AIN7 analog input. · p. 518
3 SWDCLK
Serial wire debug clock input for debug and programming. · p. 518
4 SWDIO
Serial wire debug I/O for debug and programming. · p. 518
5 P0.21
General purpose I/O; optional TRACECLK trace buffer clock. · p. 518
6 P0.22
General purpose I/O; optional TRACEDATA[0] trace buffer data. · p. 518
7 GND
Ground. · p. 518
8 P0.23
General purpose I/O; optional TRACEDATA[1] trace buffer data. · p. 518

Ordering codes, by the datasheet

2
nRF9151-LACA-R
LGA · Minimum ordering quantity 2000 · p. 532
nRF9151-LACA-R7
LGA · Minimum ordering quantity 100 · p. 532

Open-source boards using it

4
  • 4 layers55 × 85 mmSAE Cellular Module, the printed circuit board in 3D

    SAE Cellular Module

    ephrenm/VehiCell

    NRF9151-based cellular telemetry device designed for a FSAE EV vehicle.

    152 parts
  • 4 layers54 × 86 mmEgolf monitor, the printed circuit board in 3D

    Egolf monitor

    ewfuentes/egolf_monitor

    108 parts
  • 6 layers40 × 32 mmCollar tracker, the printed circuit board in 3D

    Collar tracker

    gokselozgur5/pcb-design-collar-tracker

    Small GPS and cellular dog-collar tracker. KiCad sources, DFM evidence and ongoing nano-SIM layout work.

    71 parts
  • 4 layers35 × 28 mmCollar tracker, the printed circuit board in 3D

    Collar tracker

    gokselozgur5/pcb-design-collar-tracker

    Small GPS and cellular dog-collar tracker. KiCad sources, DFM evidence and ongoing nano-SIM layout work.

    53 parts

Questions

What package is the NRF9151-LACA-R?

LGA-113(12.1x11.1), with 113 pins.

Where is the NRF9151-LACA-R datasheet?

Nordic Semicon publishes it: the Datasheet link on this page opens it.

Where can I order the NRF9151-LACA-R?

JLCPCB lists it as part C42236596, with 0 in stock; the sellers' links on this page open their listings.

Which open-source boards use the NRF9151-LACA-R?

4 boards in 3 repositories on GitHub; the most starred are listed on this page, with their KiCad files.