Skip to the content
49

NRF52810-QFAA-R

Nordic SemiconExtended

-96dBm 1.7V~3.6V 2.4GHz 2.4GHz~2.4835GHz 2Mbps 4.6mA 4.6mA 4dBm Bluetooth SPI、UART、ADC、I2C、PDM、PWM transceiver UQFN-48-EP(6x6) RF Transceiver ICs ROHS

Part id
nordic-semicon/NRF52810-QFAA-R
Category
RF Transceiver ICs
Package
UQFN-48-EP(6x6)
Pins
48
In stock
34,347 at JLCPCB (C141828)
Used on
2 open-source boards

Overview

The NRF52810-QFAA-R is a RF Transceiver IC made by Nordic Semicon in a UQFN-48-EP(6x6) package with 49 pins. -96dBm 1.7V~3.6V 2.4GHz 2.4GHz~2.4835GHz 2Mbps 4.6mA 4.6mA 4dBm Bluetooth SPI、UART、ADC、I2C、PDM、PWM transceiver UQFN-48-EP(6x6) RF Transceiver ICs ROHS.

PCBKit's library has its KiCad symbol (EasyEDA_Cloud:NRF52810-QFAA-E-R, from EasyEDA) and its footprint (EasyEDA_Cloud:UQFN-48_L6.0-W6.0-P0.40-BL-EP4.6, from EasyEDA), ready for a KiCad board. 34,347 are in stock at JLCPCB (part C141828). 2 open-source boards in 1 repository on GitHub use it.

Symbol

49EP48VDD47DCC46DEC445VSS44NC43P0.31/AIN742P0.30/AIN641P0.29/AIN540P0.28/AIN439P0.2738P0.2637P0.2536VDD35XC234XC133DEC332DEC231VSS30ANT29P0.2428P0.2327P0.2226SWDIO25SWDCLK24P0.21/nRESET23P0.2022P0.1921P0.1820P0.1719P0.1618P0.1517P0.1416P0.1315P0.1214P0.1113VDD12P0.1011P0.0910P0.089P0.078P0.067P0.05/AIN36P0.04/AIN25P0.03/AIN14P0.02/AIN03P0.01/XL22P0.00/XL11DEC1
EasyEDA_Cloud:NRF52810-QFAA-E-RFrom EasyEDA

Footprint

49
EasyEDA_Cloud:UQFN-48_L6.0-W6.0-P0.40-BL-EP4.6From EasyEDA

From the datasheet

11
Supply, least
1.7 V · VDD, recommended operating min, independent of DCDC enable · p. 407
Supply, most
3.6 V · VDD, recommended operating max, independent of DCDC enable · p. 407
Supply, absolute maximum
3.9 V · VDD, absolute max · p. 408
Works from
-40 °C · TA, operating temperature min · p. 407
Works up to
85 °C · TA, operating temperature max · p. 407
Takes working
4.6 mA · typical RX only, DCDC, 3 V, 1 Mbps BLE · p. 210
Takes at most
15.4 mA · typical TX only at +4 dBm, LDO · p. 210
Takes asleep
300 nA · typical System OFF, no RAM retention, wake on reset, 3 V · p. 46
Data rate, most
2 Mbit/s · on-the-air data rate max · p. 210
Takes working
10 mA · RX only, LDO, 1 Mbps / BLE 1 Mbps, typical · p. 210
Takes at most
7 mA · TX only, DCDC, 3 V, +4 dBm, typical · p. 210

What it is and has

47
Radio
2.4 GHz transceiver · p. 2
Flash memory
192 kB · p. 2
RAM
24 kB · p. 2
Core
ARM Cortex-M4 32-bit processor, 64 MHz · p. 2
Radio sensitivity
-96 dBm in Bluetooth low energy mode · p. 2
Radio data rates
1 Mbps, 2 Mbps Bluetooth low energy mode · p. 2
Transmit power
-20 to +4 dBm, configurable in 4 dB steps · p. 2
ADC
12-bit, 200 ksps, 8 configurable channels with programmable gain · p. 2
RF balun
On-chip, single-ended RF · p. 2
Comparator
64 level · p. 2
Temperature sensor
Integrated · p. 2
GPIO
Up to 32 · p. 2
RSSI
1 dB resolution · p. 2
PWM
4-channel unit with EasyDMA · p. 2
PDM
Digital microphone interface · p. 2
Timers
3x 32-bit with counter mode · p. 2
SPI
Master/slave with EasyDMA · p. 2
I2C
Compatible 2-wire master/slave · p. 2
Debug
Serial wire debug (SWD) · p. 2
UART
CTS/RTS with EasyDMA · p. 2
PPI
Programmable peripheral interconnect · p. 2
QDEC
Quadrature decoder · p. 2
Power management
Fully automatic LDO and DC/DC regulator system · p. 2
Encryption
AES hardware encryption with EasyDMA · p. 2
RTC
2 · p. 2
Crystal operation
Single crystal · p. 2
Package options
QFN48, 6 x 6 mm · p. 2
Package options
QFN32, 5 x 5 mm · p. 2
Package options
WLCSP, 2.482 x 2.464 mm · p. 2
Software support
Nordic SoftDevice ready · p. 2
Multi-protocol
Support for concurrent multi-protocol · p. 2
Power regulators
On-chip LDO and DC/DC regulators · p. 49
Power modes
System ON/OFF with individual RAM section power control · p. 49
Wakeup
Analog or digital pin wakeup from System OFF · p. 49
Protection
Power on reset, brownout, and power fail supervisor · p. 49
Internal high-frequency oscillator
64 MHz · p. 62
High-frequency crystal oscillator
64 MHz using external 32 MHz crystal · p. 62
Low-frequency RC oscillator
32.768 kHz +/-500 ppm · p. 62
Low-frequency crystal oscillator
32.768 kHz using external 32.768 kHz crystal · p. 62
GPIO pull resistors
Internal pull-up and pull-down resistors · p. 116
PDM microphone inputs
Up to two microphones as a Left/Right pair sharing a data input · p. 130
PDM output
16 kHz sample rate, 16-bit samples · p. 130
PDM buffering
EasyDMA · p. 130
TWI
I2C compatible master, 100 kHz and 400 kHz · p. 298
UART duplex
Full-duplex operation · p. 352
UART flow control
Automatic flow control · p. 352
UART parity
Parity checking and generation for the 9th data bit · p. 352

Specifications

123
ParameterConditionsAs printedPage
CPU running CoreMark ICPU064 MHz from flash, Clock = HFXO, Regulator = DCDC; VDD = 3 V, 25°Ctyp 2.2 mA44
CPU running CoreMark ICPU164 MHz from flash, Clock = HFXO, Regulator = LDO; VDD = 3 V, 25°Ctyp 4.2 mA44
CPU running CoreMark ICPU264 MHz from RAM, Clock = HFXO, Regulator = DCDC; VDD = 3 V, 25°Ctyp 2.1 mA44
CPU running CoreMark ICPU364 MHz from RAM, Clock = HFXO, Regulator = LDO; VDD = 3 V, 25°Ctyp 4 mA44
CPU running CoreMark ICPU464 MHz from flash, Clock = HFINT, Regulator = DCDC; VDD = 3 V, 25°Ctyp 2 mA44
Radio transmitting IRADIO_TX04 dBm output power, 1 Mbps Bluetooth low energy mode, Clock = HFXO, Regulator = DCDC; VDD = 3 V, 25°Ctyp 8 mA45
Radio transmitting IRADIO_TX10 dBm output power, 1 Mbps Bluetooth low energy mode, Clock = HFXO, Regulator = DCDC; VDD = 3 V, 25°Ctyp 5.8 mA45
Radio transmitting IRADIO_TX2-40 dBm output power, 1 Mbps Bluetooth low energy mode, Clock = HFXO, Regulator = DCDC; VDD = 3 V, 25°Ctyp 3.4 mA45
Radio receiving IRADIO_RX01 Mbps Bluetooth low energy mode, Clock = HFXO, Regulator = DCDC; VDD = 3 V, 25°Ctyp 6.1 mA45
Radio transmitting IRADIO_TX30 dBm output power, 1 Mbps Bluetooth low energy mode, Clock = HFXO, Regulator = LDO; VDD = 3 V, 25°Ctyp 10.5 mA45
Radio transmitting IRADIO_TX4-40 dBm output power, 1 Mbps Bluetooth low energy mode, Clock = HFXO, Regulator = LDO; VDD = 3 V, 25°Ctyp 5.1 mA45
Radio receiving IRADIO_RX11 Mbps Bluetooth low energy mode, Clock = HFXO, Regulator = LDO; VDD = 3 V, 25°Ctyp 10.8 mA45
System ON, No RAM retention, Wake on any event ION_RAMOFF_EVENTVDD = 3 V, 25°C, Regulator = LDOtyp 0.6 uA46
System ON, Full 24 kB RAM retention, Wake on any event ION_RAMON_EVENTVDD = 3 V, 25°C, Regulator = LDOtyp 0.8 uA46
System ON, Full 24 kB RAM retention, Wake on any event, Power fail comparator enabled ION_RAMON_POFVDD = 3 V, 25°C, Regulator = LDOtyp 0.8 uA46
System ON, Full 24 kB RAM retention, Wake on GPIOTE input (Event mode) ION_RAMON_GPIOTEVDD = 3 V, 25°C, Regulator = LDOtyp 3.3 uA46
System ON, Full 24 kB RAM retention, Wake on GPIOTE PORT event ION_RAMON_GPIOTEPORTVDD = 3 V, 25°C, Regulator = LDOtyp 0.8 uA46
System ON, Full 24 kB RAM retention, Wake on RTC (running from LFRC clock) ION_RAMON_RTCVDD = 3 V, 25°C, Regulator = LDOtyp 1.5 uA46
System ON, No RAM retention, Wake on RTC (running from LFRC clock) ION_RAMOFF_RTCVDD = 3 V, 25°C, Regulator = LDOtyp 1.4 uA46
System ON, Full 24 kB RAM retention, Wake on RTC (running from LFXO clock) ION_RAMON_RTC_LFXOVDD = 3 V, 25°C, Regulator = LDOtyp 1.1 uA46
System ON, No RAM retention, Wake on RTC (running from LFXO clock) ION_RAMOFF_RTC_LFXOVDD = 3 V, 25°C, Regulator = LDOtyp 1 uA46
System OFF, No RAM retention, Wake on reset IOFF_RAMOFF_RESETVDD = 3 V, 25°C, Regulator = LDOtyp 0.3 uA46
System OFF, Full 24 kB RAM retention, Wake on reset IOFF_RAMON_RESETVDD = 3 V, 25°C, Regulator = LDOtyp 0.5 uA46
CPU running CoreMark from flash, Radio transmitting IS00 dBm output power, 1 Mbps Bluetooth low energy mode, Clock = HFXO, Regulator = DCDC; VDD = 3 V, 25°Ctyp 7.4 mA48
CPU running CoreMark from flash, Radio receiving IS11 Mbps Bluetooth low energy mode, Clock = HFXO, Regulator = DCDC; VDD = 3 V, 25°Ctyp 7.6 mA48
CPU running CoreMark from flash, Radio transmitting IS20 dBm output power, 1 Mbps Bluetooth low energy mode, Clock = HFXO, Regulator = LDO; VDD = 3 V, 25°Ctyp 13.8 mA48
CPU running CoreMark from flash, Radio receiving IS31 Mbps Bluetooth low energy mode, Clock = HFXO, Regulator = LDO; VDD = 3 V, 25°Ctyp 14.2 mA48
One TIMER instance running ITIMER01 MHz, Clock = HFINT; VDD = 3 V, 25°C, Regulator = LDOtyp 432 uA48
Two TIMER instances running ITIMER11 MHz, Clock = HFINT; VDD = 3 V, 25°C, Regulator = LDOtyp 432 uA48
One TIMER instance running ITIMER21 MHz, Clock = HFXO; VDD = 3 V, 25°C, Regulator = LDOtyp 730 uA48
One TIMER instance running ITIMER316 MHz, Clock = HFINT; VDD = 3 V, 25°C, Regulator = LDOtyp 495 uA48
One TIMER instance running ITIMER416 MHz, Clock = HFXO; VDD = 3 V, 25°C, Regulator = LDOtyp 792 uA48
RNG running IRNG0VDD = 3 V, 25°C, Regulator = LDOtyp 539 uA48
TEMP started ITEMP0VDD = 3 V, 25°C, Regulator = LDOtyp 998 uA48
SAADC sampling ISAADC,RUN16 ksps, Acquisition time = 20 us, Clock = HFXO, Regulator = DCDC; VDD = 3 V, 25°Ctyp 1.1 mA48
COMP enabled, low power mode ICOMP,LPVDD = 3 V, 25°C, Regulator = LDOtyp 17.2 uA48
COMP enabled, normal mode ICOMP,NORMVDD = 3 V, 25°C, Regulator = LDOtyp 21 uA48
COMP enabled, high-speed mode ICOMP,HSVDD = 3 V, 25°C, Regulator = LDOtyp 28.7 uA48
Supply voltage, independent of DCDC enable VDDmin 1.7 · typ 3 · max 3.6 V407
Supply rise time (0 V to 1.7 V) tR_VDDmax 60 ms407
Operating temperature TAmin -40 · typ 25 · max 85 °C407
VDD VDDSupply voltagesmin -0.3 · max 3.9 V408
VSS VSSSupply voltagesmax 0 V408
I/O pin voltage VI/OVDD ≤ 3.6 Vmin -0.3 V408
I/O pin voltage VI/OVDD > 3.6 Vmin -0.3 · max 3.9 V408
RF input levelRadiomax 10 dBm408
Storage temperatureQFN packagemin -40 · max 125 °C408
MSLQFN package; Moisture Sensitivity Levelmax 2408
ESD HBMQFN package; Human Body Modelmax 4 kV408
ESD CDMQFN package; Charged Device Modelmax 1 kV408
RetentionFlash memory, at 40°Cmin 10 years408
Current at VSS+0.4 V IOL,SDoutput set low, standard drive, VDD ≥1.7min 1 · typ 2 · max 4 mA123
Current at VSS+0.4 V IOL,HDHoutput set low, high drive, VDD >= 2.7 Vmin 6 · typ 10 · max 15 mA123
Current at VSS+0.4 V IOL,HDLoutput set low, high drive, VDD >= 1.7 Vmin 3 mA123
Current at VDD-0.4 V IOH,SDoutput set high, standard drive, VDD ≥1.7min 1 · typ 2 · max 4 mA123
Current at VDD-0.4 V IOH,HDHoutput set high, high drive, VDD >= 2.7 Vmin 6 · typ 9 · max 14 mA123
Operating frequencies fOPmin 2360 · max 2500 MHz210
PLL programming resolution fPLL,PROG,REStyp 2 kHz210
PLL channel spacing fPLL,CH,SPtyp 1 MHz210
On-the-air data rate fskSPSmin 1 · max 2 Mbps210
TX only run current ITX,PLUS4dBM,DCDCDCDC, 3V, PRF =+4 dBmtyp 7 mA210
TX only run current ITX,PLUS4dBMPRF = +4 dBmtyp 15.4 mA210
TX only run current ITX,0dBM,DCDCDCDC, 3V, PRF = 0dBmtyp 4.6 mA210
TX only run current ITX,0dBMPRF = 0dBmtyp 10.1 mA210
TX only run current ITX,MINUS4dBM,DCDCDCDC, 3V, PRF = -4dBmtyp 3.6 mA210
TX only run current ITX,MINUS4dBMPRF = -4 dBmtyp 7.8 mA210
TX only run current ITX,MINUS8dBM,DCDCDCDC, 3V, PRF = -8 dBmtyp 3.2 mA210
TX only run current ITX,MINUS8dBMPRF = -8 dBmtyp 6.8 mA210
TX only run current ITX,MINUS12dBM,DCDCDCDC, 3V, PRF = -12 dBmtyp 2.9 mA210
TX only run current ITX,MINUS12dBMPRF = -12 dBmtyp 6.2 mA210
TX only run current ITX,MINUS16dBM,DCDCDCDC, 3V, PRF = -16 dBmtyp 2.7 mA210
TX only run current ITX,MINUS16dBMPRF = -16 dBmtyp 5.7 mA210
TX only run current ITX,MINUS20dBM,DCDCDCDC, 3V, PRF = -20 dBmtyp 2.5 mA210
TX only run current ITX,MINUS20dBMPRF = -20 dBmtyp 5.4 mA210
TX only run current ITX,MINUS40dBM,DCDCDCDC, 3V, PRF = -40 dBmtyp 2.1 mA210
TX only run current ITX,MINUS40dBMPRF = -40 dBmtyp 4.3 mA210
RX only run current IRX,1M,DCDCDCDC, 3V, 1 Mbps / 1 Mbps BLEtyp 4.6 mA210
RX only run current IRX,1M1 Mbps / 1 Mbps BLEtyp 10 mA210
RX only run current IRX,2M,DCDCDCDC, 3V, 2 Mbps / 2 Mbps BLEtyp 5.2 mA210
RX only run current IRX,2M2 Mbps / 2 Mbps BLEtyp 11.2 mA210
RX start-up current ISTART,RX,1M,DCDCDCDC, 3 V, 1 Mbps / 1 Mbps BLEtyp 3.5 mA210
RX start-up current ISTART,RX,1M1 Mbps / 1 Mbps BLEtyp 6.7 mA210
Maximum output power PRFtyp 4 · max 8 dBm210
RF power control range PRFCtyp 24 dB210
1st Adjacent Channel Transmit Power 1 MHz (1 Mbps) PRF1,1typ -25 dBc210
2nd Adjacent Channel Transmit Power 2 MHz (1 Mbps) PRF2,1typ -50 dBc211
1st Adjacent Channel Transmit Power 2 MHz (2 Mbps) PRF1,2typ -25 dBc211
2nd Adjacent Channel Transmit Power 4 MHz (2 Mbps) PRF2,2typ -50 dBc211
WDT started IWDT,STARTEDtyp 1.3 uA49
Time from OFF to CPU execute tOFF2ONtyp 16.5 us62
Time from IDLE to CPU execute tIDLE2CPUtyp 3 us62
Time from HW event to PPI event in Constant Latency System ON mode tEVTSET,CL1Constant Latency System ON modetyp 0.0625 us62
Time from HW event to PPI event in Low Power System ON mode tEVTSET,CL0Low Power System ON modetyp 0.0625 us62
Nominal power level warning thresholds (falling supply voltage). Levels are configurable between Min. and Max. in 100mV increments. VPOFFalling supply voltagemin 1.7 · max 2.8 V62
Threshold voltage hysteresis VPOFHYSTtyp 50 mV62
Brown out reset voltage range SYSTEM OFF mode VBOR,OFFSYSTEM OFF modemin 1.2 · max 1.7 V62
Brown out reset voltage range SYSTEM ON mode VBOR,ONSYSTEM ON modemin 1.48 · max 1.7 V62
Latency between setting an EGU event flag and the system setting an interrupt tEGU,EVTtyp 1 cycles116
TX only run current (DCDC, 3V) PRF =+4 dBm ITX,PLUS4dBM,DCDCDCDC, 3V, PRF = +4 dBmtyp 7 mA210
TX only run current PRF = +4 dBm ITX,PLUS4dBMPRF = +4 dBmtyp 15.4 mA210
TX only run current (DCDC, 3V)PRF = 0dBm ITX,0dBM,DCDCDCDC, 3V, PRF = 0dBmtyp 4.6 mA210
TX only run current PRF = 0dBm ITX,0dBMPRF = 0dBmtyp 10.1 mA210
TX only run current DCDC, 3V PRF = -4dBm ITX,MINUS4dBM,DCDCDCDC, 3V, PRF = -4dBmtyp 3.6 mA210
TX only run current PRF = -4 dBm ITX,MINUS4dBMPRF = -4 dBmtyp 7.8 mA210
TX only run current DCDC, 3V PRF = -8 dBm ITX,MINUS8dBM,DCDCDCDC, 3V, PRF = -8 dBmtyp 3.2 mA210
TX only run current PRF = -8 dBm ITX,MINUS8dBMPRF = -8 dBmtyp 6.8 mA210
TX only run current DCDC, 3V PRF = -12 dBm ITX,MINUS12dBM,DCDCDCDC, 3V, PRF = -12 dBmtyp 2.9 mA210
TX only run current PRF = -12 dBm ITX,MINUS12dBMPRF = -12 dBmtyp 6.2 mA210
TX only run current DCDC, 3V PRF = -16 dBm ITX,MINUS16dBM,DCDCDCDC, 3V, PRF = -16 dBmtyp 2.7 mA210
TX only run current PRF = -16 dBm ITX,MINUS16dBMPRF = -16 dBmtyp 5.7 mA210
TX only run current DCDC, 3V PRF = -20 dBm ITX,MINUS20dBM,DCDCDCDC, 3V, PRF = -20 dBmtyp 2.5 mA210
TX only run current PRF = -20 dBm ITX,MINUS20dBMPRF = -20 dBmtyp 5.4 mA210
TX only run current DCDC, 3V PRF = -40 dBm ITX,MINUS40dBM,DCDCDCDC, 3V, PRF = -40 dBmtyp 2.1 mA210
TX only run current PRF = -40 dBm ITX,MINUS40dBMPRF = -40 dBmtyp 4.3 mA210
RX only run current (DCDC, 3V) 1 Mbps / 1 Mbps BLE IRX,1M,DCDCDCDC, 3V, 1 Mbps / 1 Mbps BLEtyp 4.6 mA210
RX only run current 1 Mbps / 1 Mbps BLE IRX,1M1 Mbps / 1 Mbps BLEtyp 10 mA210
RX only run current (DCDC, 3V) 2 Mbps / 2 Mbps BLE IRX,2M,DCDCDCDC, 3V, 2 Mbps / 2 Mbps BLEtyp 5.2 mA210
RX only run current 2 Mbps / 2 Mbps BLE IRX,2M2 Mbps / 2 Mbps BLEtyp 11.2 mA210
RX start-up current (DCDC, 3 V) 1 Mbps / 1 Mbps BLE ISTART,RX,1M,DCDCDCDC, 3 V, 1 Mbps / 1 Mbps BLEtyp 3.5 mA210
RX start-up current 1 Mbps / 1 Mbps BLE ISTART,RX,1M1 Mbps / 1 Mbps BLEtyp 6.7 mA210
1st Adjacent Channel Transmit Power 1 MHz (1 Mbps) PRF1,11 MHz (1 Mbps)typ -25 dBc210
I/O pin voltage VI/OVDD ≤ 3.6 V; maximum is VDD + 0.3 Vmin -0.3 V408
RetentionFlash memory; at 40°Cmin 10 years408

Pins, by the datasheet

15
1 DEC1
0.9 V regulator digital supply decoupling. · p. 387
2 P0.00/XL1
General purpose I/O or analog input connection for 32.768 kHz crystal (LFXO). · p. 387
37 P0.25
General purpose I/O. · p. 389
38 P0.26
General purpose I/O. · p. 389
39 P0.27
General purpose I/O. · p. 389
40 P0.28/AIN4
General purpose I/O, COMP input or SAADC input. · p. 387
41 P0.29/AIN5
General purpose I/O, COMP input or SAADC input. · p. 387
42 P0.30/AIN6
General purpose I/O, COMP input or SAADC input. · p. 387
43 P0.31/AIN7
General purpose I/O pin, COMP input or SAADC input. · p. 387
44 NC
No connect; leave unconnected. · p. 389
45 VSS
Ground. · p. 389
46 DEC4
1.3 V regulator supply decoupling; input from DC/DC regulator and output from 1.3 V LDO. · p. 389
47 DCC
DC/DC regulator output. · p. 389
48 VDD
Power supply. · p. 389
Die pad VSS
Exposed die pad must be connected to ground (VSS) for proper device operation. · p. 389

Open-source boards using it

2
  • 4 layers46 × 46 mmPlacement, the printed circuit board in 3D

    Placement

    anil08607/stm32-smartwatch

    A 46 × 46 mm, four-layer Bluetooth smartwatch PCB with a Nordic nRF52810-QFAA, 240 × 240 SPI LCD interface, BMA456 accelerometer, battery-backed PCF8563 RTC, USB-C 5 V charging, protected single-cell battery interface…

    71 parts
  • 4 layers46 × 46 mmRouter base, the printed circuit board in 3D

    Router base

    anil08607/stm32-smartwatch

    A 46 × 46 mm, four-layer Bluetooth smartwatch PCB with a Nordic nRF52810-QFAA, 240 × 240 SPI LCD interface, BMA456 accelerometer, battery-backed PCF8563 RTC, USB-C 5 V charging, protected single-cell battery interface…

    71 parts

Parts like it

4

Questions

Is there a KiCad symbol and footprint for the NRF52810-QFAA-R?

Yes. The symbol is EasyEDA_Cloud:NRF52810-QFAA-E-R and the footprint EasyEDA_Cloud:UQFN-48_L6.0-W6.0-P0.40-BL-EP4.6, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the NRF52810-QFAA-R?

UQFN-48-EP(6x6), with 49 pins. Its footprint is drawn on this page.

Where is the NRF52810-QFAA-R datasheet?

Nordic Semicon publishes it: the Datasheet link on this page opens it.

Where can I order the NRF52810-QFAA-R?

JLCPCB lists it as part C141828, with 34,347 in stock; the sellers' links on this page open their listings.

What can replace the NRF52810-QFAA-R?

Parts like it in the library: the NRF51802-QFAA-R by Nordic Semicon, the NRF51802-QFAA-R7 by Nordic Semicon, the NRF52810-QFAA-E-R by Nordic Semicon and the NRF52810-QFAA-E-R7 by Nordic Semicon. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the NRF52810-QFAA-R?

2 boards in 1 repository on GitHub; the most starred are listed on this page, with their KiCad files.