
USB2517I-JZX-TR
Microchip TechnologyExtended
-40℃~+85℃ 130mA 3V~3.6V 480Mbps 7 Controller USB 2.0 QFN-64-EP(9x9) USB Converters ROHS
- Part id
- microchip/USB2517I-JZX-TR
- Category
- USB Converters
- Package
- QFN-64-EP(9x9)
- Pins
- 65
- In stock
- 1,057 at JLCPCB (C626667)
- Used on
- 2 open-source boards
Overview
The USB2517I-JZX-TR is a USB Converter made by Microchip Technology in a QFN-64-EP(9x9) package with 65 pins. -40℃~+85℃ 130mA 3V~3.6V 480Mbps 7 Controller USB 2.0 QFN-64-EP(9x9) USB Converters ROHS.
PCBKit's library has its KiCad symbol (EasyEDA_Cloud:USB2517I-JZX-TR, from EasyEDA) and its footprint (qfn-64-1ep-9x9mm-p0-5mm:QFN-64-1EP_9x9mm_P0.5mm, from Antmicro), ready for a KiCad board. 1,057 are in stock at JLCPCB (part C626667). 2 open-source boards in 1 repository on GitHub use it.
Symbol
Footprint
From the datasheet
12- Supply, least
- 1.62 V · VDD18, VDDA18PLL, recommended operating min · p. 48
- Supply, most
- 1.98 V · VDD18, VDDA18PLL, recommended operating max · p. 48
- Supply, least
- 3 V · VDDA33, VDDA33PLL, VDD33, VDD33CR, recommended operating min · p. 48
- Supply, most
- 3.6 V · VDDA33, VDDA33PLL, VDD33, VDD33CR, recommended operating max · p. 48
- Supply, absolute maximum
- 2.5 V · VDD18, VDDA18PLL, absolute max · p. 47
- Supply, absolute maximum
- 4.6 V · VDDA33, VDD33PLL, VDD33, VDD33CR, absolute max · p. 47
- Works from
- -40 °C · industrial operating ambient min · p. 48
- Works up to
- 85 °C · industrial operating ambient max · p. 48
- Takes working
- 420 mA · sum of all supplies, configured Hi-Speed host, 7 ports at HS, typical · p. 50
- Takes at most
- 460 mA · sum of all supplies, configured Hi-Speed host, 7 ports at HS, max · p. 50
- Takes asleep
- 360 µA · sum of all supplies, suspend, typical · p. 50
- Takes asleep
- 110 µA · sum of all supplies, reset, typical · p. 50
What it is and has
10- Downstream ports
- 7 · p. 1
- Package
- 64-Pin (9x9 mm) QFN, RoHS compliant · p. 1
- Power-on reset
- On-chip POR · p. 1
- Internal regulator
- 1.8V · p. 1
- USB termination
- Integrated termination and pull-up/pull-down resistors · p. 1
- Crystal
- Parallel resonant, fundamental mode, 24 MHz ±350 ppm · p. 52
- External clock
- 24 MHz ±350 ppm; 50% duty cycle ±10% · p. 52
- I2C EEPROM frequency
- 58.6KHz ±20% fixed · p. 52
- SMBus clock stretching
- Supports stretching by other devices; does not stretch SCLK · p. 41
- SMBus alert
- Not supported · p. 41
Around it
2- res 10K
- between PRT_DIS_P[7:1] / PRT_DIS_M[7:1] and 3.3V; Pull up the applicable downstream port-disable strap when the strap is enabled by package and configuration settings. · p. 10
- crystal 24 MHz 350ppm
- between XTAL1 and XTAL2; Parallel resonant, fundamental mode; typical circuit uses C1 and C2 selected from crystal load and board/trace capacitance. · p. 52
Specifications
52| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Storage Temperature TSTOR | min -55 · max 150 °C | 47 | |
| Lead Temperature | Soldering < 10 seconds | max 325 °C | 47 |
| 1.8V supply voltage VDDA18PLL, VDD18 | max 2.5 V | 47 | |
| 3.3V supply voltage VDDA33, VDD33PLL, VDD33, VDD33CR | max 4.6 V | 47 | |
| Voltage on any I/O pin | min -0.5 · max 5.5 V | 47 | |
| Voltage on XTAL1 | min -0.5 · max 4 V | 47 | |
| Voltage on XTAL2 | min -0.5 · max 3.6 V | 47 | |
| HBM ESD Performance | max 4 kV | 47 | |
| Operating Temperature TA | USB2517I industrial; ambient temperature in still air; minimum from Note 8-2 | min -40 °C | 48 |
| Operating Temperature TA | USB2517I industrial; ambient temperature in still air; maximum from Note 8-3 | max 85 °C | 48 |
| 1.8V supply voltage VDDA18PLL, VDD18 | min 1.62 · max 1.98 V | 48 | |
| 3.3V supply voltage VDDA33, VDDA33PLL, VDD33, VDD33CR | min 3 · max 3.6 V | 48 | |
| 3.3V supply rise time tRT | See Note 8-1 and Figure 8-1 | max 400 s | 48 |
| Voltage on any I/O pin | If any 3.3V supply drops below 3.0V, maximum becomes (3.3V supply voltage) + 0.5 | min -0.3 · max 5.5 V | 48 |
| Voltage on XTAL1 | Maximum is VDD33 | min -0.3 V | 48 |
| Voltage on XTAL2 | Maximum is VDD18 | min -0.3 V | 48 |
| Low Input Level VILI | I, IS Type Input Buffer; TTL Levels | max 0.8 V | 49 |
| High Input Level VIHI | I, IS Type Input Buffer | min 2 V | 49 |
| Input Leakage IIL | I, IS Type Input Buffer; VIN = 0 to VDD33 | min -10 · max 10 uA | 49 |
| Hysteresis (‘IS’ Only) VHYSI | I, IS Type Input Buffer | min 250 · max 350 mV | 49 |
| Low Input Level VILI | Input Buffer with Pull-Up (IPU); TTL Levels | max 0.8 V | 49 |
| High Input Level VIHI | Input Buffer with Pull-Up (IPU) | min 2 V | 49 |
| Low Input Leakage IILL | Input Buffer with Pull-Up (IPU); VIN = 0 | min 35 · max 90 uA | 49 |
| High Input Leakage IIHL | Input Buffer with Pull-Up (IPU); VIN = VDD33 | min -10 · max 10 uA | 49 |
| Low Input Level VILI | Input Buffer with Pull-Down (IPD); TTL Levels | max 0.8 V | 49 |
| High Input Level VIHI | Input Buffer with Pull-Down (IPD) | min 2 V | 49 |
| Low Input Leakage IILL | Input Buffer with Pull-Down (IPD); VIN = 0; signs and columns retained as printed | min 10 · max -10 uA | 49 |
| High Input Leakage IIHL | Input Buffer with Pull-Down (IPD); VIN = VDD33; signs and columns retained as printed | min -35 · max -90 uA | 49 |
| Low Input Level VILCK | ICLK Input Buffer | max 0.5 V | 50 |
| High Input Level VIHCK | ICLK Input Buffer | min 1.4 V | 50 |
| Input Leakage IIL | ICLK Input Buffer; VIN = 0 to VDD33 | min -10 · max 10 uA | 50 |
| Low Output Level VOL | O12, I/O12 & I/OSD12 Type Buffer; IOL = 12mA @ VDD33 = 3.3V | max 0.4 V | 50 |
| High Output Level VOH | O12, I/O12 & I/OSD12 Type Buffer; IOH = -12mA @ VDD33 = 3.3V | min 2.4 V | 50 |
| Output Leakage IOL | O12, I/O12 & I/OSD12 Type Buffer; VIN = 0 to VDD33; current pins in high impedance | min -10 · max 10 uA | 50 |
| Hysteresis (‘I/OSD12’ pad only) VHYSC | O12, I/O12 & I/OSD12 Type Buffer | min 250 · max 350 mV | 50 |
| Hi-Speed Host ICCINTHS | Supply Current Unconfigured | typ 95 mA | 50 |
| Full-Speed Host ICCINITFS | Supply Current Unconfigured | typ 95 mA | 50 |
| 1 Port HS, 1 Port LS/FS IHCH1C1 | Supply Current Configured (Hi-Speed Host); all supplies combined | typ 230 mA | 50 |
| 2 Ports @ LS/FS IHCC2 | Supply Current Configured (Hi-Speed Host); all supplies combined | typ 230 mA | 50 |
| 2 Ports @ HS IHCH2 | Supply Current Configured (Hi-Speed Host); all supplies combined | typ 270 mA | 50 |
| 4 Ports @ HS IHCH4 | Supply Current Configured (Hi-Speed Host); all supplies combined | typ 330 mA | 50 |
| 7 Ports @ HS IHCH7 | Supply Current Configured (Hi-Speed Host); all supplies combined; Note 8-6 maximum measured with ICH10 EHCI controller, file transfers in Windows7, fastest available HDs, VDD=3.3V+20%, case temperature -55C | typ 420 · max 460 mA | 50 |
| 1 Port IFCC1 | Supply Current Configured (Full-Speed Host); all supplies combined | typ 205 mA | 50 |
| 2 Ports IFCC2 | Supply Current Configured (Full-Speed Host); all supplies combined | typ 210 mA | 50 |
| 3 Ports IFCC3 | Supply Current Configured (Full-Speed Host); all supplies combined | typ 215 mA | 50 |
| 4 Ports IFCC4 | Supply Current Configured (Full-Speed Host); all supplies combined | typ 220 mA | 50 |
| 7 Ports IFCC7 | Supply Current Configured (Full-Speed Host); all supplies combined | typ 235 · max 270 mA | 50 |
| Supply Current Suspend ICSBY | All supplies combined | typ 360 · max 610 A | 50 |
| Supply Current Reset ICRST | All supplies combined | typ 110 · max 400 A | 50 |
| Clock Input Capacitance CXTAL | TA = 25°C; fc = 1MHz; VDD18, VDDPLL = 1.8V; all pins except USB pins (and pins under test tied to AC ground) | max 2 pF | 51 |
| Input Capacitance CIN | TA = 25°C; fc = 1MHz; VDD18, VDDPLL = 1.8V | max 10 pF | 51 |
| Output Capacitance COUT | TA = 25°C; fc = 1MHz; VDD18, VDDPLL = 1.8V | max 20 pF | 51 |
Pins, by the datasheet
24- 59 USBUP_DP
- Upstream USB bus data; connects to host port or upstream hub. · p. 10
- 58 USBUP_DM
- Upstream USB bus data; connects to host port or upstream hub. · p. 10
- 44 VBUS_DET
- Detects upstream VBUS power to control the internal D+ pull-up; connect to upstream VBUS for a detachable hub, or 3.3V or 5.0V for a self-powered application with permanently attached host. · p. 10
- 56 USBDN7_DP/PRT_DIS_P7
- Downstream port 7 USB data; optional port-disable strap sampled at RESET_N negation. · p. 7
- 54 USBDN6_DP/PRT_DIS_P6
- Downstream port 6 USB data; optional port-disable strap sampled at RESET_N negation. · p. 7
- 12 USBDN5_DP/PRT_DIS_P5
- Downstream port 5 USB data; optional port-disable strap sampled at RESET_N negation. · p. 7
- 9 USBDN4_DP/PRT_DIS_P4
- Downstream port 4 USB data; optional port-disable strap sampled at RESET_N negation. · p. 7
- 7 USBDN3_DP/PRT_DIS_P3
- Downstream port 3 USB data; optional port-disable strap sampled at RESET_N negation. · p. 7
- 4 USBDN2_DP/PRT_DIS_P2
- Downstream port 2 USB data; optional port-disable strap sampled at RESET_N negation. · p. 7
- 2 USBDN1_DP/PRT_DIS_P1
- Downstream port 1 USB data; optional port-disable strap sampled at RESET_N negation. · p. 7
- 55 USBDN7_DM/PRT_DIS_M7
- Downstream port 7 USB data; optional port-disable strap sampled at RESET_N negation. · p. 7
- 53 USBDN6_DM/PRT_DIS_M6
- Downstream port 6 USB data; optional port-disable strap sampled at RESET_N negation. · p. 7
- 11 USBDN5_DM/PRT_DIS_M5
- Downstream port 5 USB data; optional port-disable strap sampled at RESET_N negation. · p. 7
- 8 USBDN4_DM/PRT_DIS_M4
- Downstream port 4 USB data; optional port-disable strap sampled at RESET_N negation. · p. 7
- 6 USBDN3_DM/PRT_DIS_M3
- Downstream port 3 USB data; optional port-disable strap sampled at RESET_N negation. · p. 7
- 3 USBDN2_DM/PRT_DIS_M2
- Downstream port 2 USB data; optional port-disable strap sampled at RESET_N negation. · p. 7
- 1 USBDN1_DM/PRT_DIS_M1
- Downstream port 1 USB data; optional port-disable strap sampled at RESET_N negation. · p. 7
- 36 PRTPWR7
- Enables power to downstream port 7; supports active high power controllers only. · p. 7
- 39 PRTPWR6
- Enables power to downstream port 6; supports active high power controllers only. · p. 7
- 30 PRTPWR5
- Enables power to downstream port 5; supports active high power controllers only. · p. 7
- 20 PRTPWR4
- Enables power to downstream port 4; supports active high power controllers only. · p. 7
- 23 PRTPWR3
- Enables power to downstream port 3; supports active high power controllers only. · p. 7
- 26 PRTPWR2
- Enables power to downstream port 2; supports active high power controllers only. · p. 7
- 29 PRTPWR1
- Enables power to downstream port 1; supports active high power controllers only. · p. 7
Open-source boards using it
2- 4 layers100 × 80 mm

- 4 layers100 × 80 mm

Parts like it
1Questions
Is there a KiCad symbol and footprint for the USB2517I-JZX-TR?
Yes. The symbol is EasyEDA_Cloud:USB2517I-JZX-TR and the footprint qfn-64-1ep-9x9mm-p0-5mm:QFN-64-1EP_9x9mm_P0.5mm, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the USB2517I-JZX-TR?
QFN-64-EP(9x9), with 65 pins. Its footprint is drawn on this page.
Where is the USB2517I-JZX-TR datasheet?
Microchip Technology publishes it: the Datasheet link on this page opens it.
Where can I order the USB2517I-JZX-TR?
JLCPCB lists it as part C626667, with 1,057 in stock; the sellers' links on this page open their listings.
What can replace the USB2517I-JZX-TR?
Parts like it in the library: the FT4232HQ-TRAY by FTDI. Check their datasheets: a part that fits the footprint may still differ in its ratings.
Which open-source boards use the USB2517I-JZX-TR?
2 boards in 1 repository on GitHub; the most starred are listed on this page, with their KiCad files.