
RN2483A-I/RM
Microchip Technology
Low-Power Long Range LoRa® Technology Transceiver Module
- Part id
- microchip/RN2483A-I/RM
- Category
- Uncategorised
- Pins
- 47
- Used on
- 3 open-source boards
Overview
The RN2483A-I/RM is an uncategorised made by Microchip Technology with 47 pins. Low-Power Long Range LoRa® Technology Transceiver Module.
PCBKit's library has its KiCad symbol (Analog & Interface:RN2483A, from CERN's library) and its footprint (RF_Module:RN2483, from KiCad's library), ready for a KiCad board. 3 open-source boards in 3 repositories on GitHub use it.
Symbol
Footprint
Pinout
47| Pin | Name | Type |
|---|---|---|
| 1 | GND | Power in |
| 2 | UART_RTS | Output |
| 3 | UART_CTS | Input |
| 4 | DNC | Passive |
| 5 | DNC | Passive |
| 6 | UART_TX | Output |
| 7 | UART_RX | Input |
| 8 | GND | Power in |
| 9 | GPIO13 | Input/output |
| 10 | GPIO12 | Input/output |
| 11 | GND | Power in |
| 12 | VDD | Power in |
| 13 | GPIO11 | Input/output |
| 14 | GPIO10 | Input/output |
| 15 | NC | Passive |
| 16 | NC | Passive |
| 17 | NC | Passive |
| 18 | NC | Passive |
| 19 | NC | Passive |
| 20 | GND | Power in |
| 21 | GND | Power in |
| 22 | GND | Power in |
| 23 | RFH | Input |
| 24 | GND | Power in |
| 25 | RFL | Input |
| 26 | GND | Power in |
| 27 | GND | Power in |
| 28 | GND | Power in |
| 29 | NC | Passive |
| 30 | PGC_INT | Input/output |
| 31 | PGD_INT | Input/output |
| 32 | RESET | Input |
| 33 | GND | Power in |
| 34 | VDD | Power in |
| 35 | GPIO0 | Input/output |
| 36 | GPIO1 | Input/output |
| 37 | GPIO2 | Input/output |
| 38 | GPIO3 | Input/output |
| 39 | GPIO4 | Input/output |
| 40 | GPIO5 | Input/output |
| 41 | GND | Power in |
| 42 | NC | Passive |
| 43 | GPIO6 | Input/output |
| 44 | GPIO7 | Input/output |
| 45 | GPIO8 | Input/output |
| 46 | GPIO9 | Input/output |
| 47 | GND | Power in |
Open-source boards using it
3- 2 layers

- 2 layers68.6 × 53.3 mm

Shield Arduino MOSH
Khomat/GIRIBALDI-DUBOIS_MOSH_Project
The goal of this project is to build a connected gas sensor and build the interface around the sensor.
23 parts - 2 layers75 × 55 mm

Parts like it
2Questions
Is there a KiCad symbol and footprint for the RN2483A-I/RM?
Yes. The symbol is Analog & Interface:RN2483A and the footprint RF_Module:RN2483, both drawn on this page. PCBKit places them on a board for you when you design with it.
What can replace the RN2483A-I/RM?
Parts like it in the library: the RN2483-I/RM101 by Microchip Technology and the RN2483A-I/RM103 by Microchip Technology. Check their datasheets: a part that fits the footprint may still differ in its ratings.
Which open-source boards use the RN2483A-I/RM?
3 boards in 3 repositories on GitHub; the most starred are listed on this page, with their KiCad files.