PIC16F15243-I/SS
Microchip TechnologyExtended
-40℃~+85℃ 1.8V~5.5V 10bit 17 256Byte 3.5KB 32MHz 8 Bit Built-in FLASH PIC SSOP-20 Microcontrollers (MCU/MPU/SOC) ROHS
- Part id
- microchip/PIC16F15243-I/SS
- Category
- Microcontrollers (MCU, MPU, SOC)
- Package
- SSOP-20-208mil
- Pins
- 20
- In stock
- 78 at JLCPCB (C3235617)
Overview
The PIC16F15243-I/SS is a microcontroller made by Microchip Technology in a SSOP-20-208mil package with 20 pins. -40℃~+85℃ 1.8V~5.5V 10bit 17 256Byte 3.5KB 32MHz 8 Bit Built-in FLASH PIC SSOP-20 Microcontrollers (MCU/MPU/SOC) ROHS.
PCBKit's library has its footprint (Package_SO:SSOP-20_5.3x7.2mm_P0.65mm, from KiCad's library), ready for a KiCad board. 78 are in stock at JLCPCB (part C3235617).
Symbol
The library has no symbol for this part yet.
Footprint
From the datasheet
13- Supply, least
- 1.8 V · VDD, recommended operating min, FOSC ≤ 16 MHz · p. 366
- Supply, most
- 5.5 V · VDD, recommended operating max, FOSC ≤ 16 MHz · p. 366
- Supply, least
- 2.5 V · VDD, recommended operating min, FOSC > 16 MHz · p. 366
- Supply, absolute maximum
- 6.5 V · VDD, absolute max · p. 364
- Works from
- -40 °C · Industrial operating ambient min · p. 3
- Works up to
- 85 °C · Industrial operating ambient max · p. 3
- Junction, hottest
- 150 °C · Maximum junction temperature · p. 371
- Takes working
- 2.7 mA · Typical active current, HFINTOSC = 32 MHz, VDD = 3.0V · p. 367
- Takes at most
- 3.6 mA · Max active current, HFINTOSC = 32 MHz, VDD = 3.0V · p. 367
- Takes asleep
- 400 nA · Typical base Sleep current, VDD = 3.0V, 25°C · p. 368
- A pin gives at most
- 25 mA · Absolute max source or sink current per standard I/O pin · p. 364
- Junction to air (20-pin SSOP package)
- 31.1 K/W · Typical junction-to-ambient thermal resistance · p. 371
- Edge
- 5 ns · Typical port I/O rise time, slew rate disabled, VDD = 3.0V · p. 375
What it is and has
14- Program Flash memory
- 3.5K bytes · p. 1
- Data SRAM
- 256 bytes · p. 1
- I/O
- 18 pins, Peripheral Pin Select · p. 1
- ADC
- 10-bit, 12 external and 2 internal channels · p. 1
- CCP
- 2 modules · p. 3
- PWM
- 2 pulse-width modulators · p. 3
- Timer0
- Configurable 8/16-bit · p. 3
- Timer1
- 16-bit with gate control · p. 3
- Timer2
- 8-bit with Hardware Limit Timer · p. 3
- EUSART
- 1 · p. 3
- MSSP
- 1, SPI or I2C · p. 3
- ADC
- 10-bit · p. 1
- Peripheral Pin Select
- PPS · p. 1
- Memory Access Partition
- Data protection and bootloader support · p. 1
Around it
10- cap 0.1 μF (100 nF)
- between VDD and VSS; Required on every supply-pin pair; 10-25V ceramic recommended, low ESR; place close to pins, preferably on the same board side, with trace length no greater than 6 mm. · p. 14
- cap 0.01 μF to 0.001 μF
- between VDD and VSS; Additional ceramic capacitor in parallel with each primary decoupling capacitor when high-frequency noise is present; place next to the primary capacitor. · p. 15
- cap 4.7 μF to 47 μF
- between VDD and VSS; Typical tank-capacitor range for power traces longer than six inches; select for trace resistance, application current and acceptable voltage sag. · p. 15
- res 10 kΩ
- between VDD and MCLR pull-up junction; R1 in the recommended MCLR circuit; 10 kΩ is the suggested starting value and upper recommended resistance. R2 connects this junction to MCLR. · p. 15
- res 100Ω to 470Ω
- between MCLR pull-up junction and MCLR; R2 in the minimum recommended connections; limits current from C1 into MCLR. · p. 14
- cap 10 nF
- between MCLR pull-up junction and VSS; C1, 16V ceramic, in the recommended MCLR circuit; isolate from MCLR during programming and debugging. · p. 14
- res a few tens of ohms, not to exceed 100Ω
- between ICSP connector signal and ICSPCLK or ICSPDAT; Series resistance recommended if the ICSP connector is expected to experience an ESD event. · p. 15
- res 1 kΩ to 10 kΩ
- between Unused I/O and VSS; Alternative to configuring unused I/O pins as outputs driven low. · p. 16
- cap 0.1 μF
- between VDD and VSS; In parallel with 0.01 uF, as close to the device as possible, to ensure oscillator frequency tolerances. · p. 374
- cap 0.01 μF
- between VDD and VSS; In parallel with 0.1 uF, as close to the device as possible, to ensure oscillator frequency tolerances. · p. 374
Specifications
119| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Ambient temperature under bias | min -40 · max 125 °C | 364 | |
| Storage temperature | min -65 · max 150 °C | 364 | |
| Voltage on pins with respect to VSS • on VDD pin | min -0.3 · max 6.5 V | 364 | |
| Voltage on pins with respect to VSS • on MCLR pin | min -0.3 · max 9 V | 364 | |
| Voltage on pins with respect to VSS • on all other pins | min -0.3 V | 364 | |
| Maximum current • on VSS pin(1) | -40°C ≤ TA ≤ +85°C; even load distribution across I/O pins | max 300 mA | 364 |
| Maximum current • on VSS pin(1) | 85°C < TA ≤ +125°C; even load distribution across I/O pins | max 120 mA | 364 |
| Maximum current • on VDD pin(1) | -40°C ≤ TA ≤ +85°C; even load distribution across I/O pins | max 250 mA | 364 |
| Maximum current • on VDD pin(1) | 85°C < TA ≤ +125°C; even load distribution across I/O pins | max 85 mA | 364 |
| Maximum current • on any standard I/O pin | min -25 · max 25 mA | 364 | |
| Clamp current IK | VPIN < 0 or VPIN > VDD | min -20 · max 20 mA | 364 |
| Total power dissipation(2) | max 800 mW | 364 | |
| Supply Voltage VDD | FOSC ≤ 16 MHz | min 1.8 · max 5.5 V | 366 |
| Supply Voltage VDD | FOSC > 16 MHz | min 2.5 · max 5.5 V | 366 |
| RAM Data Retention(1) VDR | Device in Sleep mode | min 1.7 V | 366 |
| Power-on Reset Release Voltage(2) VPOR | BOR disabled(3); typical at 3.0V, 25°C | typ 1.6 V | 366 |
| Power-on Reset Rearm Voltage(2) VPORR | BOR disabled(3); typical at 3.0V, 25°C | typ 1.1 V | 366 |
| VDD Rise Rate to ensure internal Power-on Reset signal(2) SVDD | BOR disabled(3) | min 0.05 V/ms | 366 |
| HFINTOSC = 16 MHz IDDHFO16 | VDD = 3.0V; active operation; all I/O outputs driven low; MCLR = VDD; WDT disabled; typical at 25°C | typ 1.5 · max 2.1 mA | 367 |
| HFINTOSC = 32 MHz IDDHFOPLL | VDD = 3.0V; active operation; all I/O outputs driven low; MCLR = VDD; WDT disabled; typical at 25°C | typ 2.7 · max 3.6 mA | 367 |
| IPD Base IPD | VDD = 3.0V; Sleep; I/O high-impedance and tied to VSS; max at +85°C; typical at 25°C | typ 0.4 · max 2.5 uA | 368 |
| IPD Base IPD | VDD = 3.0V; Sleep; I/O high-impedance and tied to VSS; max at +125°C; typical at 25°C | typ 0.4 · max 12 uA | 368 |
| Low-Frequency Internal Oscillator/WDT IPD_WDT | VDD = 3.0V; Sleep; max at +85°C; typical at 25°C | typ 0.5 · max 3.6 uA | 368 |
| Low-Frequency Internal Oscillator/WDT IPD_WDT | VDD = 3.0V; Sleep; max at +125°C; typical at 25°C | typ 0.5 · max 6.1 uA | 368 |
| FVR IPD_FVR | VDD = 3.0V; Sleep; max at +85°C; typical at 25°C | typ 40 · max 64 uA | 368 |
| FVR IPD_FVR | VDD = 3.0V; Sleep; max at +125°C; typical at 25°C | typ 40 · max 66 uA | 368 |
| Brown-out Reset (BOR) IPD_BOR | VDD = 3.0V; Sleep; max at +85°C; typical at 25°C | typ 25 · max 35 uA | 368 |
| Brown-out Reset (BOR) IPD_BOR | VDD = 3.0V; Sleep; max at +125°C; typical at 25°C | typ 25 · max 40 uA | 368 |
| ADC - Active IPD_ADCA | VDD = 3.0V; Sleep; ADC non-converting; ADCRC clock source; max at +85°C | max 3 uA | 368 |
| ADC - Active IPD_ADCA | VDD = 3.0V; Sleep; ADC non-converting; ADCRC clock source; max at +125°C | max 5.6 uA | 368 |
| Input Low Voltage, I/O PORT: with TTL buffer VIL | 4.5V ≤ VDD ≤ 5.5V | max 0.8 V | 368 |
| Input Low Voltage, I/O PORT: with SMBus levels VIL | 2.7V ≤ VDD ≤ 5.5V | max 0.8 V | 368 |
| Input High Voltage, I/O PORT: with TTL buffer VIH | 4.5V ≤ VDD ≤ 5.5V | min 2 V | 369 |
| Input High Voltage, I/O PORT: with SMBus levels VIH | 2.7V ≤ VDD ≤ 5.5V | min 2.1 V | 369 |
| Weak Pull-up Current IPUR | VDD = 3.0V, VPIN = VSS; typical at 25°C | min 25 · typ 120 · max 200 uA | 369 |
| Output Low Voltage, Standard I/O PORTS VOL | IOL = 10 mA, VDD = 3.0V | max 0.6 V | 369 |
| All I/O Pins CIO | Typical at 3.0V, 25°C | typ 5 · max 50 pF | 369 |
| Voltage on MCLR/VPP pin to enter programming mode VIHH | High Voltage Entry Programming Mode; Note 2 | min 7.9 · max 9 V | 369 |
| Current on MCLR/VPP pin during programming mode IPPGM | High Voltage Entry Programming Mode; Note 2 | max 0.6 mA | 369 |
| Thermal Resistance Junction to Ambient θJA | 20-pin SSOP package; -40°C ≤ TA ≤ +125°C | typ 31.1 °C/W | 371 |
| Maximum Junction Temperature TJMAX | -40°C ≤ TA ≤ +125°C | typ 150 °C | 371 |
| Clock Frequency FECL | ECL Oscillator | max 16 MHz | 372 |
| Clock Duty Cycle TECL_DC | ECL Oscillator | min 40 · max 60 % | 372 |
| Clock Frequency FECH | ECH Oscillator | max 32 MHz | 372 |
| Clock Duty Cycle TECH_DC | ECH Oscillator | min 40 · max 60 % | 372 |
| CLKOUT rising edge delay (rising edge FOSC (Q1 cycle) to falling edge CLKOUT TCLKOUTH | Characterized but not tested | max 70 ns | 375 |
| CLKOUT falling edge delay (rising edge FOSC (Q3 cycle) to rising edge CLKOUT TCLKOUTL | Characterized but not tested | max 72 ns | 375 |
| Port output valid time (rising edge FOSC (Q1 cycle) to port valid) TIO_VALID | Characterized but not tested | typ 50 · max 70 ns | 375 |
| Port input setup time (Setup time before rising edge FOSC – Q2 cycle) TIO_SETUP | Characterized but not tested | min 20 ns | 375 |
| Port input hold time (Hold time after rising edge FOSC – Q2 cycle) TIO_HOLD | Characterized but not tested | min 50 ns | 375 |
| Port I/O rise time, slew rate enabled TIOR_SLREN | VDD = 3.0V; characterized but not tested | typ 25 ns | 375 |
| Port I/O rise time, slew rate disabled TIOR_SLRDIS | VDD = 3.0V; characterized but not tested | typ 5 ns | 375 |
| Port I/O fall time, slew rate enabled TIOF_SLREN | VDD = 3.0V; characterized but not tested | typ 25 ns | 375 |
| Port I/O fall time, slew rate disabled TIOF_SLRDIS | VDD = 3.0V; characterized but not tested | typ 5 ns | 375 |
| INT pin high or low time to trigger an interrupt TINT | Characterized but not tested | min 25 ns | 375 |
| Interrupt-on-Change minimum high or low time to trigger interrupt TIOC | Characterized but not tested | min 25 ns | 375 |
| Voltage on pins with respect to VSS | on VDD pin | min -0.3 · max 6.5 V | 364 |
| Voltage on pins with respect to VSS | on MCLR pin | min -0.3 · max 9 V | 364 |
| Voltage on pins with respect to VSS | on all other pins | min -0.3 V | 364 |
| Maximum current on VSS pin(1) | -40°C ≤ TA ≤ +85°C | max 300 mA | 364 |
| Maximum current on VSS pin(1) | 85°C < TA ≤ +125°C | max 120 mA | 364 |
| Maximum current on VDD pin(1) | -40°C ≤ TA ≤ +85°C | max 250 mA | 364 |
| Maximum current on VDD pin(1) | 85°C < TA ≤ +125°C | max 85 mA | 364 |
| Power-on Reset Release Voltage(2) VPOR | BOR disabled(3) | typ 1.6 V | 366 |
| Power-on Reset Rearm Voltage(2) VPORR | BOR disabled(3) | typ 1.1 V | 366 |
| HFINTOSC = 16 MHz IDDHFO16 | VDD = 3.0V; all I/O pins outputs driven low; MCLR = VDD; WDT disabled | typ 1.5 · max 2.1 mA | 367 |
| HFINTOSC = 32 MHz IDDHFOPLL | VDD = 3.0V; all I/O pins outputs driven low; MCLR = VDD; WDT disabled | typ 2.7 · max 3.6 mA | 367 |
| IPD Base IPD | VDD = 3.0V; Max. +85°C; Sleep mode | typ 0.4 · max 2.5 uA | 368 |
| IPD Base IPD | VDD = 3.0V; Max. +125°C; Sleep mode | typ 0.4 · max 12 uA | 368 |
| Low-Frequency Internal Oscillator/WDT IPD_WDT | VDD = 3.0V; Max. +85°C | typ 0.5 · max 3.6 uA | 368 |
| Low-Frequency Internal Oscillator/WDT IPD_WDT | VDD = 3.0V; Max. +125°C | typ 0.5 · max 6.1 uA | 368 |
| FVR IPD_FVR | VDD = 3.0V; Max. +85°C | typ 40 · max 64 uA | 368 |
| FVR IPD_FVR | VDD = 3.0V; Max. +125°C | typ 40 · max 66 uA | 368 |
| Brown-out Reset (BOR) IPD_BOR | VDD = 3.0V; Max. +85°C | typ 25 · max 35 uA | 368 |
| Brown-out Reset (BOR) IPD_BOR | VDD = 3.0V; Max. +125°C | typ 25 · max 40 uA | 368 |
| ADC - Active IPD_ADCA | VDD = 3.0V; Max. +85°C; ADC is non-converting; ADC clock source is ADCRC | max 3 uA | 368 |
| ADC - Active IPD_ADCA | VDD = 3.0V; Max. +125°C; ADC is non-converting; ADC clock source is ADCRC | max 5.6 uA | 368 |
| Input Low Voltage VIL | I/O PORT with TTL buffer; 4.5V ≤ VDD ≤ 5.5V | max 0.8 V | 368 |
| Input Low Voltage VIL | I/O PORT with SMBus levels; 2.7V ≤ VDD ≤ 5.5V | max 0.8 V | 368 |
| Input High Voltage VIH | I/O PORT with TTL buffer; 4.5V ≤ VDD ≤ 5.5V | min 2 V | 369 |
| Input High Voltage VIH | I/O PORT with SMBus levels; 2.7V ≤ VDD ≤ 5.5V | min 2.1 V | 369 |
| Weak Pull-up Current IPUR | VDD = 3.0V, VPIN = VSS | min 25 · typ 120 · max 200 uA | 369 |
| Output Low Voltage VOL | Standard I/O PORTS; IOL = 10 mA, VDD = 3.0V | max 0.6 V | 369 |
| All I/O Pins CIO | typ 5 · max 50 pF | 369 | |
| Voltage on MCLR/VPP pin to enter programming mode VIHH | High Voltage Entry Programming Mode; required only if LVP bit is disabled | min 7.9 · max 9 V | 369 |
| Current on MCLR/VPP pin during programming mode IPPGM | High Voltage Entry Programming Mode; required only if LVP bit is disabled | max 0.6 mA | 369 |
| VDD for Bulk Erase VBE | Note 3: Refer to the Family Programming Specification | typ 2.9 V | 370 |
| Supply Current during Programming operation IDDPGM | max 10 mA | 370 | |
| Characteristic Retention TP_RET | Provided no other specifications are violated | typ 40 Year | 370 |
| Self-Timed Row Erase or Self-Timed Write TP_REW | max 2.8 ms | 370 | |
| Thermal Resistance Junction to Ambient θJA | 20-pin SSOP package | typ 31.1 °C/W | 371 |
| Maximum Junction Temperature TJMAX | typ 150 °C | 371 | |
| System Clock Frequency FOSC | System Oscillator; Note 2, Note 3 | max 32 MHz | 373 |
| Instruction Period TCY | System Oscillator; Note 1 | min 125 ns | 373 |
| Precision Calibrated HFINTOSC Frequency FHFOSC | Note 2 | typ 4 MHz | 373 |
| Precision Calibrated HFINTOSC Frequency FHFOSC | Note 2 | typ 16 MHz | 373 |
| Precision Calibrated HFINTOSC Frequency FHFOSC | Note 2 | typ 32 MHz | 373 |
| Low-Power Optimized HFINTOSC Frequency FHFOSCLP | -40°C to 85°C | min 0.92 · typ 1 · max 1.08 MHz | 373 |
| Low-Power Optimized HFINTOSC Frequency FHFOSCLP | -40°C to 85°C | min 1.84 · typ 2 · max 2.16 MHz | 373 |
| Internal Calibrated MFINTOSC Frequency FMFOSC | typ 500 kHz | 373 | |
| Internal LFINTOSC Frequency FLFOSC | min 26.5 · typ 31 · max 36 kHz | 373 | |
| HFINTOSC Wake-up from Sleep Start-up Time THFOSCST | typ 19 · max 40 us | 373 | |
| LFINTOSC Wake-up from Sleep Start-up Time TLFOSCST | typ 0.2 · max 1 ms | 374 | |
| MCLR Pulse Width Low to ensure Reset TMCLR | Characterized but not tested | min 2 us | 377 |
| I/O high-impedance from Reset detection TIOZ | Characterized but not tested | max 2 us | 377 |
| Watchdog Timer Time-out Period TWDT | 1:512 Prescaler | typ 16 ms | 377 |
| Power-up Timer Period TPWRT | PWRTS = ‘10’ (64 ms); characterized but not tested | typ 65 ms | 377 |
| Brown-out Reset Voltage VBOR | BORV = 0 | min 2.4 · typ 2.8 · max 3 V | 377 |
| Brown-out Reset Voltage VBOR | BORV = 1; maximum corresponds to VBORMAX | min 1.8 · typ 1.9 · max 2 V | 377 |
| Brown-out Reset Hysteresis VBORHYS | typ 40 mV | 377 | |
| Brown-out Reset Response Time TBORDC | typ 3 us | 377 | |
| Resolution NR | VDD = 3.0V, TA = 25°C | max 10 bit | 377 |
| Integral Error EIL | VDD = 3.0V, TA = 25°C; ADCREF+ = 3.0V, ADCREF- = VSS | typ 0.5 LSb | 377 |
| Differential Error EDL | VDD = 3.0V, TA = 25°C; ADCREF+ = 3.0V, ADCREF- = VSS | typ 0.3 LSb | 377 |
| Offset Error EOFF | VDD = 3.0V, TA = 25°C; ADCREF+ = 3.0V, ADCREF- = VSS | typ 1 LSb | 377 |
| Gain Error EGN | VDD = 3.0V, TA = 25°C; ADCREF+ = 3.0V, ADCREF- = VSS | typ 0.8 LSb | 377 |
| ADC Reference Voltage (ADREF+) VADREF | VDD = 3.0V, TA = 25°C | min 1.8 V | 377 |
| Recommended Impedance of Analog Voltage Source ZAIN | VDD = 3.0V, TA = 25°C | typ 10 kΩ | 377 |
| ADC Voltage Reference Ladder Impedance RVREF | VDD = 3.0V, TA = 25°C | typ 50 kΩ | 377 |
Parts like it
8PIC16F1827-I/SS
SSOP-20-208mil-40℃~+85℃ 1.8V~5.5V 10bit 16 256Byte 32MHz 384Byte 7KB 8 Bit Built-in FLASH PIC SSOP-20-208mil Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)PIC16F1829-I/SS
SSOP-20-208mil-40℃~+85℃ 1.8V~5.5V 10bit 14KB 17 1KB 256Byte 32MHz 8 Bit Built-in FLASH PIC SSOP-20-208mil Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)PIC16F15345-I/SS
SSOP-20-40℃~+85℃ 10bit 14KB 18 1KB 2.3V~5.5V 32MHz 5bit 8 Bit Built-in FLASH PIC SSOP-20 Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)PIC18F13K22-I/SS
SSOP-20-208mil-40℃~+85℃ 10bit 17 2.3V~5.5V 256Byte 256Byte 64MHz 8 Bit 8KB Built-in FLASH PIC SSOP-20-208mil Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)PIC18F14K50-I/SS
SSOP-20-208mil-40℃~+85℃ 1.8V~5.5V 10bit 14 16KB 256Byte 48MHz 768Byte 8 Bit Built-in FLASH PIC SSOP-20-208mil Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)PIC16F15344-I/SS
SSOP-20-208mil-40℃~+85℃ 10bit 18 2.3V~5.5V 32MHz 512Byte 5bit 7KB 8 Bit Built-in FLASH PIC SSOP-20-208mil Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)PIC16F1828-I/SS
SSOP-20-208mil-40℃~+85℃ 1.8V~5.5V 10bit 17 256Byte 32MHz 7KB 8 Bit Built-in FLASH PIC SSOP-20-208mil Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)PIC16F18345-I/SS
SSOP-20-208mil-40℃~+85℃ 10bit 14KB 18 1KB 2.3V~5.5V 256Byte 32MHz 5bit 8 Bit Built-in FLASH PIC SSOP-20-208mil Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)
Questions
Is there a KiCad symbol and footprint for the PIC16F15243-I/SS?
Yes. the footprint Package_SO:SSOP-20_5.3x7.2mm_P0.65mm, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the PIC16F15243-I/SS?
SSOP-20-208mil, with 20 pins. Its footprint is drawn on this page.
Where is the PIC16F15243-I/SS datasheet?
Microchip Technology publishes it: the Datasheet link on this page opens it.
Where can I order the PIC16F15243-I/SS?
JLCPCB lists it as part C3235617, with 78 in stock; the sellers' links on this page open their listings.
What can replace the PIC16F15243-I/SS?
Parts like it in the library: the PIC16F1827-I/SS by Microchip Technology, the PIC16F1829-I/SS by Microchip Technology, the PIC16F15345-I/SS by Microchip Technology and the PIC18F13K22-I/SS by Microchip Technology. Check their datasheets: a part that fits the footprint may still differ in its ratings.