PAC1954-E/4MX
Microchip TechnologyExtended
-40℃~+125℃@(TA) 1.35V 12uA 2.7V~5.5V 4 No Open Drain Power Supervisor VQFN-16(3x3) Supervisor and Reset ICs ROHS
- Part id
- microchip/PAC1954-E/4MX
- Category
- Supervisor And Reset ICs
- Package
- VQFN-16(3x3)
- Pins
- 17
- In stock
- 182 at JLCPCB (C3687526)
Overview
The PAC1954-E/4MX is a supervisor And Reset IC made by Microchip Technology in a VQFN-16(3x3) package with 17 pins. -40℃~+125℃@(TA) 1.35V 12uA 2.7V~5.5V 4 No Open Drain Power Supervisor VQFN-16(3x3) Supervisor and Reset ICs ROHS.
PCBKit's library has its KiCad symbol (PAC1954T-E_VQFN:PAC1954T-E_VQFN, from Antmicro) and its footprint (vqfn-16-1ep-3x3mm-p0-5mm-ep1-1x1-1mm:VQFN-16-1EP_3x3mm_P0.5mm_EP1.1x1.1mm, from Antmicro), ready for a KiCad board. 182 are in stock at JLCPCB (part C3687526).
Symbol
Footprint
From the datasheet
11- Supply, least
- 2.7 V · VDD, recommended operating min · p. 6
- Supply, most
- 5.5 V · VDD, recommended operating max · p. 6
- Supply, absolute maximum
- 6 V · VDD, absolute maximum · p. 5
- Works from
- -40 °C · Operating ambient temperature min · p. 9
- Works up to
- 125 °C · Operating ambient temperature max · p. 9
- Takes working
- 395 µA · VDD active current typical, 1024 SPS, 4 channels enabled · p. 6
- Takes at most
- 535 µA · VDD active current max, 1024 SPS, 4 channels enabled · p. 6
- Takes asleep
- 5 µA · VDD sleep current typical · p. 6
- Junction to air (16-Lead VQFN)
- 39.9 K/W · Junction to ambient thermal resistance typical · p. 9
- Junction to case (16-Lead VQFN)
- 23.1 K/W · Junction to case thermal resistance typical · p. 9
- Data rate, most
- 3.4 Mbit/s · I2C High-Speed mode max · p. 1
What it is and has
13- Current measurement resolution
- 16-bit · p. 1
- Voltage measurement resolution
- 16-bit · p. 1
- Bus voltage full-scale range
- 0V to 32V · p. 1
- Programmable bus voltage range
- 16V · p. 1
- Current sense full-scale range
- -50 mv to +50 mv programmable · p. 1
- Energy measurement
- On-chip accumulation of 30-bit power results · p. 1
- Burst sampling rate
- 5120 SPS for a single channel · p. 1
- I2C/SMBus
- SMBus 3.1 and I2C Fast Mode Plus, 1 Mbps · p. 1
- I2C High-Speed mode
- 3.4 Mbps · p. 1
- SMBus address options
- 16, selected with resistor · p. 1
- ALERT/GPIO
- Two independent pins · p. 1
- Qualification
- AEC-Q100 qualified, VQFN · p. 1
- Package
- 3 x 3 mm 16-Lead VQFN with wettable flanks · p. 1
Specifications
81| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| VDD Pin | min -0.3 · max 6 V | 5 | |
| Voltage on SENSE- and SENSE+ Pins | min -0.3 · max 40 V | 5 | |
| Voltage on Any Other Pin to GND | min -0.3 · max 6 V | 5 | |
| Voltage between Sense Pins (|(SENSE+ – SENSE-)|) | max 500 mV | 5 | |
| Input Current to Any Pin Except VDD | min -100 · max 100 mA | 5 | |
| Operating Ambient Temperature Range | Absolute maximum stress rating | min -40 · max 150 °C | 5 |
| Storage Temperature Range | min -55 · max 150 °C | 5 | |
| ESD Rating – All Pins – HBM | max 7500 V | 5 | |
| ESD Rating – All Pins – CDM | max 2000 V | 5 | |
| VDD Range VDD | min 2.7 · max 5.5 V | 6 | |
| VDD Active Current IDD | 1024 SPS, 4 channels enabled | typ 395 · max 535 uA | 6 |
| VDD Active Current IDD | 8 SPS, 4 channels enabled | typ 12 · max 130 uA | 6 |
| VDD Sleep Current IDD_SLEEP | typ 5 uA | 6 | |
| VDD Power-Down Current IDD_PWRDN | VDD = 3.3V | min 0 · max 8 uA | 6 |
| Minimum VDD Rise Rate VDD_RISE_MIN | 0V to 5V in 100 ms | typ 0.05 V/ms | 6 |
| Maximum VDD Rise Rate VDD_RISE_MAX | 0V to 5V in 5 us | typ 1000 V/ms | 6 |
| POR Level VPOR | typ 1.35 V | 6 | |
| Bus Voltage Range VBUS | Common-mode voltage on SENSE pins, referenced to ground | min -0.2 · max 32 V | 6 |
| VSENSE Differential Input Voltage Range VSENSE_DIF | min -100 · max 100 mV | 6 | |
| SENSE+, SENSE- Pin Input Current ISENSE+, ISENSE- | VSENSE+ = VSENSE- = Full scale; all states include leakage current and average value of the capacitively coupled switching current | min -6 · typ 0.6 · max 6 uA | 6 |
| SENSE+, SENSE- Pin Input Current ISENSE+, ISENSE- | VSENSE+ = 6V, VSENSE- = 5.9V; all states include leakage current and average value of the capacitively coupled switching current | min -1 · typ 0.4 · max 1 uA | 6 |
| VBUS, VSENSE Input Trace Resistance (allowable trace resistance without measurement error) RTRACE | typ 1 k | 6 | |
| VSENSE ADC Data Resolution VSENSE_RES | max 16 Bits | 6 | |
| VSENSE LSB Step Size VSENSE_LSB | FSR = 100 mV | typ 1.5 uV | 6 |
| VSENSE LSB Step Size VSENSE_LSB | FSR = ±100 mV | typ 3.05 uV | 6 |
| VBUS LSB Step Size VBUS_LSB | FSR = 32V, 16-bit resolution | typ 488 uV | 6 |
| VBUS LSB Step Size VBUS_LSB | FSR = ±32V, 16V resolution | typ 976 uV | 6 |
| VBUS ADC Data Resolution VBUS_RES | 14 bits are used for power calculations, 16 bits are reported when the VBUS measurement result is read | max 16 Bits | 6 |
| VSENSE Gain Accuracy VSENSE_ GAIN_ERR | At +25°C; values are ± | typ 0.1 · max 0.5 % | 6 |
| VSENSE Gain Accuracy VSENSE_ GAIN_ERR | -40°C to +125°C; typical value is ± | typ 0.3 % | 6 |
| VSENSE Offset Accuracy, Referenced to Input VSENSE_OFFSET_ERR | 16-bit resolution; values are ± | typ 25 · max 100 uV | 7 |
| VBUS Gain Accuracy VBUS_GAIN_ERR | At +25°C; values are ± | typ 0.02 · max 0.25 % | 7 |
| VBUS Gain Accuracy VBUS_GAIN_ERR | -40°C to +125°C; typical value is ± | typ 0.2 % | 7 |
| Accumulator Error ACC_Err | 1 Sigma Error Range with > 1000 Accumulations; VSENSE = 97 mV | typ 0.1 % | 7 |
| Accumulator Error ACC_Err | 1 Sigma Error Range with > 1000 Accumulations; VSENSE = 10 mV | typ 0.1 % | 7 |
| Accumulator Error ACC_Err | 1 Sigma Error Range with > 1000 Accumulations; VSENSE = 1 mV | typ 1 % | 7 |
| Accumulator Error ACC_Err | 1 Sigma Error Range with > 1000 Accumulations; VSENSE = 100 uV | typ 2 % | 7 |
| Accumulator Error ACC_Err | 1 Sigma Error Range with > 1000 Accumulations; VSENSE = 50 uV | typ 4 % | 7 |
| Time to First Communications tINT_T | Time after VDD is applied before it is ready to begin communication and measurement | max 50 ms | 7 |
| Transition from Sleep State to Start of Conversion Cycle tSLEEP_TO_ACTIVE | Time from Sleep state exit commanded by register write to the beginning of the conversion cycle | max 5 ms | 7 |
| Input High Voltage VIH | Digital I/O Pins (SLOW/ALERT, SM_CLK, SM_DATA Pins) | min 1.35 V | 7 |
| Input Low Voltage VIL | Digital I/O Pins (SLOW/ALERT, SM_CLK, SM_DATA Pins) | max 0.8 V | 7 |
| Output Low Voltage VOL | Sinking 8 mA for the ALERT pins and 20 mA for the CLK pin in all modes; 4 mA for the SDA pin in 3.4 MHz mode | max 0.4 V | 7 |
| Leakage Current ILEAK | Digital I/O Pins (SLOW/ALERT, SM_CLK, SM_DATA Pins); powered or unpowered | min -0.5 · max 0.5 uA | 7 |
| Input High Voltage VIH | Digital I/O Pin (PWRDN) | min 1.3 V | 7 |
| Input Low Voltage VIL | Digital I/O Pin (PWRDN) | max 0.6 V | 7 |
| Clock Frequency fSMB | Fast Mode Plus. No minimum if Time-out is not enabled. | min 0.01 · max 1 MHz | 8 |
| Clock Frequency fSMB | High-Speed mode. No minimum if Time-out is not enabled. | min 0.01 · max 3.4 MHz | 8 |
| Spike Suppression tSP | Fast Mode Plus | min 0 · max 50 ns | 8 |
| Spike Suppression tSP | High-Speed mode | min 0 · max 10 ns | 8 |
| Bus Free Time Stop to Start tBUF | Per SMBus 3.1 | min 0.5 us | 8 |
| Hold Time after Repeated Start Condition tHD:STA | Per SMBus 3.1, Fast Mode Plus | min 0.26 us | 8 |
| Hold Time after Repeated Start Condition tHD:STA | Per SMBus 3.1, High-Speed mode | min 0.16 us | 8 |
| Repeated Start Condition Setup Time tSU:STA | Per SMBus 3.1, Fast Mode Plus | min 0.26 us | 8 |
| Repeated Start Condition Setup Time tSU:STA | Per SMBus 3.1, High-Speed mode | min 0.16 us | 8 |
| Setup Time: Stop tSU:STO | Per SMBus 3.1, Fast Mode Plus | min 0.26 us | 8 |
| Setup Time: Stop tSU:STO | Per SMBus 3.1, High-Speed mode | min 0.16 us | 8 |
| Setup Time: Start tSU:STA | Per SMBus 3.1, Fast Mode Plus | min 0.26 us | 8 |
| Setup Time: Start tSU:STA | Per SMBus 3.1, High-Speed mode | min 0.16 us | 8 |
| Data Hold Time tHD:DAT | Per SMBus 3.1, Fast Mode Plus | min 0 ns | 8 |
| Data Hold Time tHD:DAT | Per SMBus 3.1, High-Speed mode | min 0 · max 70 ns | 8 |
| Data Setup Time tSU:DAT | Per SMBus 3.1, Fast Mode Plus | min 50 ns | 8 |
| Data Setup Time tSU:DAT | Per SMBus 3.1, High-Speed mode | min 10 ns | 8 |
| Clock Low Period tLOW | Per SMBus 3.1, Fast Mode Plus | min 0.5 us | 8 |
| Clock Low Period tLOW | Per SMBus 3.1, High-Speed mode | min 0.16 us | 8 |
| Clock High Period tHIGH | Fast Mode Plus | min 0.26 · max 50 us | 8 |
| Clock High Period tHIGH | High-Speed mode | min 0.06 · max 50 us | 8 |
| Clock/Data Fall Time tFALL | Fast Mode Plus | min 12 · max 120 ns | 8 |
| Clock/Data Rise Time tRISE | Fast Mode Plus | max 120 ns | 8 |
| Clock Fall Time tfCL | High-Speed mode | min 10 · max 40 ns | 8 |
| Clock Rise Time trCL | High-Speed mode | min 10 · max 40 ns | 8 |
| Data Fall Time tfDA | High-Speed mode | min 10 · max 80 ns | 8 |
| Data Rise Time trDA | High-Speed mode | min 10 · max 80 ns | 8 |
| Capacitive Load CLOAD | Per bus line, Fast Mode Plus | max 550 pF | 9 |
| Capacitive Load CLOAD | Per bus line, High-Speed mode | max 100 pF | 9 |
| SLOW Pin Pulse Width SLOWpw | Pulses narrower than 150 uS may not be detected | min 150 us | 9 |
| Specified Temperature Range TA | min -40 · max 125 °C | 9 | |
| Operating Temperature Range TA | min -40 · max 125 °C | 9 | |
| Storage Temperature Range TSTG | min -55 · max 150 °C | 9 | |
| Thermal Resistance, 16-Lead VQFN JA | 16-Lead VQFN | typ 39.9 °C/W | 9 |
| Thermal Resistance, 16-Lead VQFN JC | 16-Lead VQFN | typ 23.1 °C/W | 9 |
Pins, by the datasheet
17- 1 SLOW/ALERT1
- Default SLOW input: high selects 8 SPS on all channels; programmable as ALERT1 or open-drain GPIO. · p. 17
- 2 VDD
- Positive power supply voltage. · p. 17
- 3 GND
- Ground for the IC. · p. 17
- 4 SCL
- SMBus clock input. · p. 17
- 5 SDA
- SMBus data I/O; requires a pull-up resistor to Host VDD. · p. 17
- 6 ADDRSEL
- Address selection for the SMBus client address. · p. 17
- 7 SENSE3-
- Connect to the load side of the channel 3 sense resistor; ground unused channels. · p. 17
- 8 SENSE3+
- Connect to the supply side of the channel 3 sense resistor; ground unused channels. · p. 17
- 9 SENSE4-
- Connect to the load side of the channel 4 sense resistor; ground unused channels. · p. 17
- 10 SENSE4+
- Connect to the supply side of the channel 4 sense resistor; ground unused channels. · p. 17
- 11 SENSE1+
- Connect to the supply side of the channel 1 sense resistor; ground unused channels. · p. 17
- 12 SENSE1-
- Connect to the load side of the channel 1 sense resistor; ground unused channels. · p. 17
- 13 SENSE2+
- Connect to the supply side of the channel 2 sense resistor; ground unused channels. · p. 17
- 14 SENSE2-
- Connect to the load side of the channel 2 sense resistor; ground unused channels. · p. 17
- 15 GPIO/ALERT2
- Default GPIO input; programmable as open-drain ALERT2 or GPIO. · p. 17
- 16 PWRDN
- Active-low input powers down all circuitry including SMBus. · p. 17
- 17 EP
- Exposed pad is not electrically connected. · p. 17
Parts like it
1Questions
Is there a KiCad symbol and footprint for the PAC1954-E/4MX?
Yes. The symbol is PAC1954T-E_VQFN:PAC1954T-E_VQFN and the footprint vqfn-16-1ep-3x3mm-p0-5mm-ep1-1x1-1mm:VQFN-16-1EP_3x3mm_P0.5mm_EP1.1x1.1mm, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the PAC1954-E/4MX?
VQFN-16(3x3), with 17 pins. Its footprint is drawn on this page.
Where is the PAC1954-E/4MX datasheet?
Microchip Technology publishes it: the Datasheet link on this page opens it.
Where can I order the PAC1954-E/4MX?
JLCPCB lists it as part C3687526, with 182 in stock; the sellers' links on this page open their listings.
What can replace the PAC1954-E/4MX?
Parts like it in the library: the PAC1944-E/4MX by Microchip Technology. Check their datasheets: a part that fits the footprint may still differ in its ratings.