MIC29302AWD-TR

Microchip TechnologyExtended

-40℃~+125℃@(Tj) 1 1.24V~15V 16V 260uVrms 3A 800mV@(3A) Adjustable Over Current Protection、Over Temperature Protection、Enable Positive TO-252-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHS

Datasheet JLCPCB LCSC

Part id: microchip/MIC29302AWD-TR
Category: Voltage Regulators, Linear, Low Drop Out (LDO) Regulators
Package: TO-252-5
Pins: 6
In stock: 128 at JLCPCB (C627907)
Used on: 2 open-source boards

Overview

The MIC29302AWD-TR is a voltage Regulators, Linear, Low Drop Out (LDO) Regulator made by Microchip Technology in a TO-252-5 package with 5 pins. -40℃~+125℃@(Tj) 1 1.24V~15V 16V 260uVrms 3A 800mV@(3A) Adjustable Over Current Protection、Over Temperature Protection、Enable Positive TO-252-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHS.

PCBKit's library has its KiCad symbol (Regulator_Linear:MIC29302AWD, from KiCad's library) and its footprint (Package_TO_SOT_SMD:TO-252-5_TabPin3, from KiCad's library), ready for a KiCad board. 128 are in stock at JLCPCB (part C627907). 2 open-source boards in 2 repositories on GitHub use it.

Symbol

Regulator_Linear:MIC29302AWDFrom KiCad's library

Footprint

Package_TO_SOT_SMD:TO-252-5_TabPin3From KiCad's library

From the datasheet

Supply, least: 3 V · IN, recommended operating min · p. 3
Supply, most: 16 V · IN, recommended operating max · p. 3
Supply, absolute maximum: 20 V · IN, absolute maximum · p. 3
Junction, hottest: 125 °C · Junction operating temperature max · p. 5
Takes working: 5 mA · Ground current typical, IOUT = 750 mA, VIN = VOUT + 1V · p. 3
Takes asleep: 32 µA · Ground pin shutdown current typical, VIN = 16V · p. 3
Gives: 3 A · Rated continuous output current max · p. 1
Current limit: 4 A · Current limit typical, VOUT = 0V · p. 3
Dropout: 100 mV · Dropout typical, IOUT = 100 mA, VIN ≥ 3.184V · p. 3
Dropout: 300 mV · Dropout typical, IOUT = 1.5A, VIN ≥ 3.184V · p. 3
Dropout: 500 mV · Dropout typical, IOUT = 2.75A, VIN ≥ 3.184V · p. 3
Dropout: 560 mV · Dropout typical, IOUT = 3A, VIN ≥ 3.4V · p. 3
Junction to case (TO-252): 3 K/W · Junction-to-case thermal resistance typical · p. 5
Junction to air (TO-252): 35 K/W · Junction-to-ambient thermal resistance typical · p. 5

What it is and has

Output voltage: 1.24V to 15V adjustable · p. 1
Accuracy: 1% tolerance · p. 1
Package options: TO-263-5L and TO-252-5L · p. 1
Transient response: Fast · p. 1

Around it

cap 10 μF: between OUT and GND; Required for stability at full load. Aluminum electrolytics are adequate; tantalum is recommended for fast load transients. Extremely low ESR may cause instability. · p. 12
cap 0.1 µF: between IN and GND; Recommended when the source has high AC impedance. · p. 12

Specifications

Parameter	Conditions	As printed	Page
Input Supply Voltage VIN		min -20 · max 20 V	3
Enable Input Voltage VEN	Maximum: VIN	min -0.3 V	3
Operating Input Voltage		min 3 · max 16 V	3
Output Voltage Accuracy ∆VOUT	100 mA ≤ IOUT ≤ 3A, (VOUT + 1V) ≤ VIN ≤ 16V	min -2 · max 2 %	3
Line Regulation ∆VOUT/∆VIN	IOUT = 100 mA, (VOUT + 1V) ≤ VIN ≤ 16V	typ 0.1 · max 0.5 %	3
Load Regulation ∆VOUT/∆IOUT	VIN = VOUT + 1V, 100 mA ≤ IOUT ≤ 3A	typ 0.2 · max 1 %	3
Dropout Voltage (Note 2) VDO	IOUT = 100 mA, VIN ≥ 3.184V	typ 100 · max 200 mV	3
Dropout Voltage (Note 2) VDO	IOUT = 1.5A, VIN ≥ 3.184V	typ 300 mV	3
Dropout Voltage (Note 2) VDO	IOUT = 2.75A, VIN ≥ 3.184V	typ 500 mV	3
Dropout Voltage (Note 2) VDO	IOUT = 3A, VIN ≥ 3.4V	typ 560 · max 800 mV	3
Ground Current IGND	IOUT = 750 mA, VIN = VOUT + 1V	typ 5 · max 20 mA	3
Ground Current IGND	IOUT = 1.5A	typ 15 mA	3
Ground Current IGND	IOUT = 3A	typ 60 · max 150 mA	3
Ground Pin Current at Dropout IGNDDO	VIN = 0.5V less than specified VOUT; IOUT = 10 mA	typ 2 mA	3
Current Limit ILIMIT	VOUT = 0V, Note 3; VIN = VOUT (nominal) + 1V; pulse testing	min 3 · typ 4 A	3
Output Noise Voltage (10 Hz to 100 kHz) eN	CL = 10 uF	typ 400 uVRMS	3
Output Noise Voltage (10 Hz to 100 kHz) eN	CL = 33 uF	typ 260 uVRMS	3
Ground Pin Current in Shutdown ISHDN	Input Voltage VIN = 16V	typ 32 uA	3
Reference Voltage VREF	Note 4	min 1.215 · max 1.267 V	3
Adjust Pin Bias Current IADJ		typ 40 nA	3
Adjust Pin Bias Current IADJ		max 120 nA	3
Input Logic Voltage VENABLE	Low (OFF)	max 0.8 V	4
Input Logic Voltage VENABLE	High (ON)	min 2.4 V	4
Enable Pin Input Current IENABLE	VEN = 4.2V	typ 15 · max 30 uA	4
Enable Pin Input Current IENABLE	VEN = 4.2V	max 75 uA	4
Enable Pin Input Current IENABLE	VEN = 0.8V	max 2 uA	4
Enable Pin Input Current IENABLE	VEN = 0.8V	max 4 uA	4
Regulator Output Current in Shutdown IOUT-SHDN	Note 5: VEN ≤ 0.8V, VIN ≤ 16V and VOUT = 0V	typ 10 uA	4
Regulator Output Current in Shutdown IOUT-SHDN	Note 5: VEN ≤ 0.8V, VIN ≤ 16V and VOUT = 0V	max 20 uA	4
Junction Operating Temperature Range TJ		min -40 · max 125 °C	5
Storage Temperature Range TS		min -65 · max 150 °C	5
Thermal Resistance TO-252 JC	TO-252	typ 3 °C/W	5
Thermal Resistance TO-252 JA	TO-252	typ 35 °C/W	5

Pins, by the datasheet

1 EN: Active-high TTL/CMOS-compatible enable input; do not float. · p. 11
2 IN: Unregulated input, +3V to +16V maximum. · p. 11
3 GND: Ground, internally connected to TAB. · p. 11
TAB GND: TAB is internally connected to the IC ground. · p. 11
4 OUT: Regulator output voltage. · p. 11
5 ADJ: 1.24V feedback from external resistor divider. · p. 11

Parameters

Current Limit: 4A
Features: Thermal shutdown
Junction Temperature(Max): 125℃
Noise: 260uVrms
Number of Outputs: 1
Operating Temperature: -40℃~+125℃@(Tj)
Output Configuration: Positive
Output Current: 3A
Output Type: Adjustable
Output Voltage: 1.24V~15V
Thermal Resistance(Junction to Ambient): 35℃/W
Thermal Resistance(Junction to Case): 3℃/W
Voltage - Supply: 3V~16V
Voltage - Supply(Absolute Max): 20V
Voltage Dropout: 800mV@(3A)
standby current: 5mA

Order codes

MIC29302AWD-TRLCSC C627907

Pinout

The pins of the MIC29302AWD-TR
Pin	Name	Type
1	EN	Input
2	VIN	Power in
3	GND	Power in
4	VOUT	Power out
5	ADJ	Input

Show this part on your page

<iframe src="https://pcbkit.io/embed/parts/microchip/MIC29302AWD-TR" title="MIC29302AWD-TR in PCBKit" width="100%" height="480" style="border:0;border-radius:12px" allow="fullscreen" loading="lazy"></iframe>

For any web page: the part itself, turned and zoomed by the reader.

Open-source boards using it

4 layers50 × 110 mm
SensorSuite CircularStack
ELWilson38/SUSF_CanSat_2526
Repo for PCB development
88 parts
2 layers82 × 66 mm
COMET1 PWR Board
Ben-Bussch/COMET-I-Static-Fire
Avionics for Static Fire of Comet 1
42 parts

Parts like it

Questions

Is there a KiCad symbol and footprint for the MIC29302AWD-TR?

Yes. The symbol is Regulator_Linear:MIC29302AWD and the footprint Package_TO_SOT_SMD:TO-252-5_TabPin3, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the MIC29302AWD-TR?

TO-252-5, with 5 pins. Its footprint is drawn on this page.

Where is the MIC29302AWD-TR datasheet?

Microchip Technology publishes it: the Datasheet link on this page opens it.

Where can I order the MIC29302AWD-TR?

JLCPCB lists it as part C627907, with 128 in stock; the sellers' links on this page open their listings.

What can replace the MIC29302AWD-TR?

Parts like it in the library: the MIC29302AWD by Microchip Technology, the LD49300PT08R by STMicroelectronics, the FAN1581D25X by onsemi and the TLE72722DATMA1 by Infineon Technologies. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the MIC29302AWD-TR?

2 boards in 2 repositories on GitHub; the most starred are listed on this page, with their KiCad files.