Skip to the content
11

MCP73833-FCI/MF

Microchip TechnologyExtended

-40℃~+85℃ 1 1A 3.75V~6V 4.2V 50uA Charging IC Support Support DFN-10-EP(3x3) Battery Management ROHS

Part id
microchip/MCP73833-FCI/MF
Category
Battery Management
Package
DFN-10-EP(3x3)
Pins
11
In stock
483 at JLCPCB (C511337)
Used on
1 open-source board

Overview

The MCP73833-FCI/MF is a battery Management made by Microchip Technology in a DFN-10-EP(3x3) package with 11 pins. -40℃~+85℃ 1 1A 3.75V~6V 4.2V 50uA Charging IC Support Support DFN-10-EP(3x3) Battery Management ROHS.

PCBKit's library has its KiCad symbol (Celestial_Charger:MICROCHIP MCP73833, from Altium's library) and its footprint (EasyEDA_Cloud:DFN-10_L3.0-W3.0-P0.50-BL-EP, from EasyEDA), ready for a KiCad board. 483 are in stock at JLCPCB (part C511337). 1 open-source board in 1 repository on GitHub use it.

Symbol

1VIN3STAT14STAT25GND7PG6PROG8THERM9VBAT11GND2VIN10VBAT
Celestial_Charger:MICROCHIP MCP73833From Altium's library

Footprint

11
EasyEDA_Cloud:DFN-10_L3.0-W3.0-P0.50-BL-EPFrom EasyEDA

From the datasheet

12
Supply, least
3.75 V · VDD, recommended charging minimum · p. 3
Supply, most
6 V · VDD, recommended charging maximum · p. 3
Supply, absolute maximum
7 V · VDD, absolute maximum · p. 3
Works from
-40 °C · ambient operating minimum · p. 5
Works up to
125 °C · ambient operating maximum · p. 5
Takes working
2 mA · VDD supply current, charging, typical · p. 3
Takes at most
3 mA · VDD supply current, charging, max · p. 3
Takes asleep
100 µA · standby, no battery or PROG floating, typical · p. 3
Takes asleep
50 µA · shutdown, VDD below VBAT or VSTOP, typical · p. 3
Gives
1 A · programmable charge current maximum · p. 1
Current limit
1.2 A · output current limit, PROG < 833Ω, typical · p. 3
Junction to air (DFN-10, 3 mm x 3 mm)
41 K/W · junction to ambient, 4-layer JC51-7 board, natural convection, typical · p. 5

What it is and has

11
Charge management
Complete linear charge management controller · p. 1
Pass transistor
Integrated · p. 1
Current sense
Integrated · p. 1
Protection
Integrated reverse discharge protection · p. 1
Charge current
Programmable, 1A maximum · p. 1
Charge status outputs
2 · p. 1
Temperature monitoring
Cell temperature monitor · p. 1
Regulator mode
Low-dropout linear regulator mode · p. 1
Protection
Under voltage lockout · p. 1
Package
DFN-10 (3 mm x 3 mm) · p. 1
Preconditioning
Deeply depleted cells · p. 1

Around it

7
cap 1 µF
between VDD and VSS; Minimum input bypass capacitance. · p. 11
cap 1 µF
between VBAT and VSS; Minimum output bypass capacitance to ensure loop stability when the battery is disconnected. · p. 11
cap 4.7 µF
between VBAT and VSS; Minimum bypass capacitance in system test (LDO) mode with IOUT > 250 mA. · p. 4
res 10 kΩ
between PROG and VSS; Programming resistance for typical 100 mA fast charge current. · p. 3
res 1.0 kΩ
between PROG and VSS; Programming resistance for typical 1000 mA fast charge current. · p. 3
res 10 kΩ
between THERM and VSS; Use when temperature monitoring is not required. · p. 17
cap 4.7 µF
between VBAT and VSS; Minimum recommended bypass capacitance for stability in Constant-voltage mode. · p. 20

Specifications

56
ParameterConditionsAs printedPage
VDD VDDmax 7 V3
All Inputs and Outputs w.r.t. VSSUpper limit is (VDD+0.3)Vmin -0.3 V3
Storage temperaturemin -65 · max 150 °C3
Human Body Model (HBM)ESD protection on all pins; 1.5 kΩ in Series with 100 pFmin 4 kV3
Machine Model (MM)ESD protection on all pins; 200 pF, No Series Resistancemax 300 V3
Supply Voltage VDDChargingmin 3.75 · max 6 V3
Supply Voltage VDDCharge Complete, Standby; minimum VREG(Typical)+0.3Vmax 6 V3
Supply Current ISSChargingtyp 2000 · max 3000 uA3
Supply Current ISSCharge Completetyp 150 · max 300 uA3
Supply Current ISSStandby (No Battery or PROG Floating)typ 100 · max 300 uA3
Supply Current ISSShutdown (VDD < VBAT, or VDD < VSTOP)typ 50 · max 100 uA3
UVLO Start Threshold VSTARTVDD Low-to-Highmin 3.4 · typ 3.55 · max 3.7 V3
UVLO Stop Threshold VSTOPVDD High-to-Lowmin 3.3 · typ 3.45 · max 3.6 V3
UVLO Hysteresis VHYStyp 100 mV3
Line Regulation |(ΔVBAT/VBAT)/ΔVDD|VDD=[VREG(Typical)+1V] to 6V, IOUT=10 mAtyp 0.1 · max 0.3 %/V3
Load Regulation |ΔVBAT/ VBAT|IOUT=10 mA to 100 mA, VDD=[VREG(Typical)+1V]typ 0.1 · max 0.3 %3
Supply Ripple Attenuation PSRRIOUT=10 mA, 10Hz to 1 kHztyp 58 dB3
Supply Ripple Attenuation PSRRIOUT=10 mA, 10Hz to 10 kHztyp 47 dB3
Supply Ripple Attenuation PSRRIOUT=10 mA, 10Hz to 1 MHztyp 25 dB3
Fast Charge Current Regulation IREGPROG = 10 kΩ; TA=-5°C to +55°Cmin 90 · typ 100 · max 110 mA3
Fast Charge Current Regulation IREGPROG = 1.0 kΩ; TA=-5°C to +55°Cmin 900 · typ 1000 · max 1100 mA3
Maximum Output Current Limit IMAXPROG < 833Ωtyp 1200 mA3
Precondition Hysteresis VPHYSVBAT High-to-Lowtyp 100 mV4
ON-Resistance RDSONVDD = 3.75V; TJ = 105°Ctyp 300 mΩ4
Output Reverse Leakage Current IDISCHARGEPROG Floatingtyp 0.15 · max 2 uA4
Output Reverse Leakage Current IDISCHARGEVDD < VBATtyp 0.25 · max 2 uA4
Output Reverse Leakage Current IDISCHARGEVDD < VSTOPtyp 0.15 · max 2 uA4
Output Reverse Leakage Current IDISCHARGECharge Completetyp -5.5 · max -15 uA4
Sink Current ISINKStatus Indicators - STAT1, STAT2, PGtyp 15 · max 25 mA4
Low Output Voltage VOLStatus Indicators - STAT1, STAT2, PG; ISINK = 4 mAtyp 0.4 · max 1 V4
Input Leakage Current ILKStatus Indicators - STAT1, STAT2, PG; High Impedance, 6V on pintyp 0.01 · max 1 uA4
Charge Impedance Range RPROGPROG Inputmin 1 · max 20 kΩ4
Standy Impedance RPROGMinimum Impedance for Standbymin 70 · max 200 kΩ4
Thermistor Current Source ITHERM2 kΩ < RTHERM < 50 kΩmin 47 · typ 50 · max 53 uA4
Upper Trip Threshold VT1VTHERM Low-to-Highmin 1.2 · typ 1.23 · max 1.26 V4
Upper Trip Point Hysteresis VT1HYStyp -50 mV4
Lower Trip Threshold VT2VTHERM High-to-Lowmin 0.235 · typ 0.25 · max 0.265 V4
Lower Trip Point Hysteresis VT2HYStyp 50 mV4
THERM Input Sink Current ISINKStand-by or system test modemin 3 · typ 6 · max 20 uA4
Bypass Capacitance CBATSystem Test (LDO) Mode; IOUT < 250 mAmin 1 uF4
Bypass Capacitance CBATSystem Test (LDO) Mode; IOUT > 250 mAmin 4.7 uF4
Die Temperature TSDThermal Shutdowntyp 150 °C5
Die Temperature Hysteresis TSDHYSThermal Shutdowntyp 10 °C5
UVLO Start Delay tSTARTVDD Low-to-Highmax 5 ms5
Transition Time Out of Preconditioning tDELAYVBAT<VPTH to VBAT>VPTHmax 1 ms5
Current Rise Time Out of Preconditioning tRISEIOUT Rising to 90% of IREGmax 1 ms5
Preconditioning Comparator Filter Time tPRECONAverage VBAT Rise/Fallmin 0.4 · typ 1.3 · max 3.2 ms5
Termination Comparator Filter Time tTERMAverage IOUT Fallingmin 0.4 · typ 1.3 · max 3.2 ms5
Charge Comparator Filter Time tCHARGEAverage VBAT Fallingmin 0.4 · typ 1.3 · max 3.2 ms5
Thermistor Comparator Filter Time tTHERMAverage THERM Rise/Fallmin 0.4 · typ 1.3 · max 3.2 ms5
Status Output turn-off tOFFISINK = 1 mA to 0 mAmax 200 us5
Status Output turn-on tONISINK = 0 mA to 1 mAmax 200 us5
Specified Temperature Range TAmin -40 · max 85 °C5
Operating Temperature Range TAmin -40 · max 125 °C5
Storage Temperature Range TAmin -65 · max 150 °C5
Thermal Resistance, DFN-10, 3 mm x 3 mm θJADFN-10, 3 mm x 3 mm; 4-Layer JC51-7 Standard Board, Natural Convectiontyp 41 °C/W5

Pins, by the datasheet

11
1 VDD
Battery management input supply; bypass to VSS with a minimum of 1 uF. · p. 11
2 VDD
Battery management input supply; bypass to VSS with a minimum of 1 uF. · p. 11
3 STAT1
Charge status output for an LED or a host microcontroller using a pull-up resistor. · p. 11
4 STAT2
Charge status output for an LED or a host microcontroller using a pull-up resistor. · p. 11
5 VSS
Battery management 0V reference; connect to the negative terminals of the battery and input supply. · p. 11
6 PROG
Current regulation set and charge control enable; resistor to VSS sets currents, and floating the input disables charging. · p. 11
7 PG
MCP73833 power good pseudo open-drain output; pull up only to the input supply. · p. 11
8 THERM
Thermistor input with an internal 50 uA bias current source for a 10 kΩ NTC thermistor. · p. 11
9 VBAT
Battery charge control output; connect to the battery positive terminal and bypass to VSS. · p. 11
10 VBAT
Battery charge control output; connect to the battery positive terminal and bypass to VSS. · p. 11
11 EP
Exposed thermal pad; must be connected to VSS. · p. 11

Ordering codes, by the datasheet

1
MCP73833-FCI/MF
10-Lead DFN (3x3) · Marking code AAAC · p. 23

Open-source boards using it

1

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the MCP73833-FCI/MF?

Yes. The symbol is Celestial_Charger:MICROCHIP MCP73833 and the footprint EasyEDA_Cloud:DFN-10_L3.0-W3.0-P0.50-BL-EP, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the MCP73833-FCI/MF?

DFN-10-EP(3x3), with 11 pins. Its footprint is drawn on this page.

Where is the MCP73833-FCI/MF datasheet?

Microchip Technology publishes it: the Datasheet link on this page opens it.

Where can I order the MCP73833-FCI/MF?

JLCPCB lists it as part C511337, with 483 in stock; the sellers' links on this page open their listings.

What can replace the MCP73833-FCI/MF?

Parts like it in the library: the XB6206AE by XySemi, the LTC4079EDD#PBF by Analog Devices, the ISL6292-1CR3Z-T by Renesas Electronics and the ISL6292-2CR3 by Renesas Electronics. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the MCP73833-FCI/MF?

1 board in 1 repository on GitHub; the most starred are listed on this page, with their KiCad files.