Skip to the content
12345678910

MCP73833-AMI/UN

Microchip TechnologyExtended

-40℃~+85℃ 1 1.2A 3.75V~6V 4.2V 50uA Charging IC Lithium Battery Support Support MSOP-10 Battery Management ROHS

Part id
microchip/MCP73833-AMI/UN
Category
Battery Management
Package
MSOP-10
Pins
10
In stock
151 at JLCPCB (C627668)
Used on
2 open-source boards

Overview

The MCP73833-AMI/UN is a battery Management made by Microchip Technology in a MSOP-10 package with 10 pins. -40℃~+85℃ 1 1.2A 3.75V~6V 4.2V 50uA Charging IC Lithium Battery Support Support MSOP-10 Battery Management ROHS.

PCBKit's library has its KiCad symbol (dk_PMIC-Battery-Chargers:MCP73833-AMI_UN, from Digikey) and its footprint (Package_SO:MSOP-10_3x3mm_P0.5mm, from KiCad's library), ready for a KiCad board. 151 are in stock at JLCPCB (part C627668). 2 open-source boards in 2 repositories on GitHub use it.

Symbol

1VDD2VDD3STAT14STAT25VSS6PROG7PG(TE)8THERM9VBAT10VBAT
dk_PMIC-Battery-Chargers:MCP73833-AMI_UNFrom Digikey

Footprint

12345678910
Package_SO:MSOP-10_3x3mm_P0.5mmFrom KiCad's library

From the datasheet

12
Supply, least
3.75 V · VDD, minimum charging supply · p. 3
Supply, most
6 V · VDD, maximum charging supply · p. 3
Supply, absolute maximum
7 V · VDD, absolute maximum · p. 3
Takes working
2 mA · VDD, typical supply current while charging · p. 3
Takes at most
3 mA · VDD, maximum supply current while charging · p. 3
Takes asleep
100 µA · VDD, typical standby current; no battery or PROG floating · p. 3
Takes asleep
50 µA · VDD, typical shutdown current; VDD < VBAT or VDD < VSTOP · p. 3
Gives
1 A · Maximum programmable charge current · p. 1
Current limit
1.2 A · Typical maximum output current limit, PROG < 833Ω · p. 3
Works from
-40 °C · TA, minimum operating temperature · p. 5
Works up to
125 °C · TA, maximum operating temperature · p. 5
Junction to air (MSOP-10)
113 K/W · Typical junction-to-ambient resistance, 4-layer JC51-7 standard board, natural convection · p. 5

What it is and has

10
Charge management
Complete linear charge management controller · p. 1
Integrated pass transistor
Yes · p. 1
Integrated current sense
Yes · p. 1
Protection
Integrated reverse discharge protection · p. 1
Programmable charge current
1A maximum · p. 1
Charge status outputs
2 · p. 1
Cell temperature monitor
Yes · p. 1
Low-dropout linear regulator mode
Yes · p. 1
Protection
Under voltage lockout · p. 1
Package
MSOP-10 · p. 1

Around it

5
cap 1 µF
between VDD and VSS; Minimum input bypass capacitance. · p. 11
cap 1 µF
between VBAT and VSS; Minimum bypass capacitance to ensure loop stability when the battery is disconnected. · p. 11
cap 4.7 µF
between VBAT and VSS; Minimum CBAT in System Test (LDO) Mode for IOUT > 250 mA. · p. 4
res 1.0 kΩ
between PROG and VSS; Programs a typical 1000 mA fast-charge current. · p. 3
res 10 kΩ
between PROG and VSS; Programs a typical 100 mA fast-charge current. · p. 3

Specifications

56
ParameterConditionsAs printedPage
VDD VDDmax 7 V3
All Inputs and Outputs w.r.t. VSSMaximum is (VDD+0.3)Vmin -0.3 V3
Storage temperaturemin -65 · max 150 °C3
ESD protection on all pins: Human Body Model (HBM)1.5 kΩ in Series with 100 pFmin 4 kV3
ESD protection on all pins: Machine Model (MM)200 pF, No Series Resistancemax 300 V3
Supply Voltage VDDChargingmin 3.75 · max 6 V3
Supply Voltage VDDCharge Complete, Standby; minimum VREG(Typical)+0.3Vmax 6 V3
Supply Current ISSChargingtyp 2000 · max 3000 uA3
Supply Current ISSCharge Completetyp 150 · max 300 uA3
Supply Current ISSStandby (No Battery or PROG Floating)typ 100 · max 300 uA3
Supply Current ISSShutdown (VDD < VBAT, or VDD < VSTOP)typ 50 · max 100 uA3
UVLO Start Threshold VSTARTVDD Low-to-Highmin 3.4 · typ 3.55 · max 3.7 V3
UVLO Stop Threshold VSTOPVDD High-to-Lowmin 3.3 · typ 3.45 · max 3.6 V3
UVLO Hysteresis VHYStyp 100 mV3
Line Regulation |(ΔVBAT/VBAT)/ΔVDD|VDD=[VREG(Typical)+1V] to 6V, IOUT=10 mAtyp 0.1 · max 0.3 %/V3
Load Regulation |ΔVBAT/ VBAT|IOUT=10 mA to 100 mA, VDD=[VREG(Typical)+1V]typ 0.1 · max 0.3 %3
Supply Ripple Attenuation PSRRIOUT=10 mA, 10Hz to 1 kHztyp 58 dB3
Supply Ripple Attenuation PSRRIOUT=10 mA, 10Hz to 10 kHztyp 47 dB3
Supply Ripple Attenuation PSRRIOUT=10 mA, 10Hz to 1 MHztyp 25 dB3
Fast Charge Current Regulation IREGPROG = 10 kΩ; TA=-5°C to +55°Cmin 90 · typ 100 · max 110 mA3
Fast Charge Current Regulation IREGPROG = 1.0 kΩ; TA=-5°C to +55°Cmin 900 · typ 1000 · max 1100 mA3
Maximum Output Current Limit IMAXPROG < 833Ωtyp 1200 mA3
Precondition Hysteresis VPHYSVBAT High-to-Lowtyp 100 mV4
ON-Resistance RDSONVDD = 3.75V; TJ = 105°Ctyp 300 mΩ4
Output Reverse Leakage Current IDISCHARGEPROG Floatingtyp 0.15 · max 2 uA4
Output Reverse Leakage Current IDISCHARGEVDD < VBATtyp 0.25 · max 2 uA4
Output Reverse Leakage Current IDISCHARGEVDD < VSTOPtyp 0.15 · max 2 uA4
Output Reverse Leakage Current IDISCHARGECharge Completetyp -5.5 · max -15 uA4
Sink Current ISINKSTAT1, STAT2, PGtyp 15 · max 25 mA4
Low Output Voltage VOLSTAT1, STAT2, PG; ISINK = 4 mAtyp 0.4 · max 1 V4
Input Leakage Current ILKSTAT1, STAT2, PG; High Impedance, 6V on pintyp 0.01 · max 1 uA4
Charge Impedance Range RPROGPROG Inputmin 1 · max 20 kΩ4
Standy Impedance RPROGMinimum Impedance for Standbymin 70 · max 200 kΩ4
Thermistor Current Source ITHERM2 kΩ < RTHERM < 50 kΩmin 47 · typ 50 · max 53 uA4
Upper Trip Threshold VT1VTHERM Low-to-Highmin 1.2 · typ 1.23 · max 1.26 V4
Upper Trip Point Hysteresis VT1HYStyp -50 mV4
Lower Trip Threshold VT2VTHERM High-to-Lowmin 0.235 · typ 0.25 · max 0.265 V4
Lower Trip Point Hysteresis VT2HYStyp 50 mV4
THERM Input Sink Current ISINKStand-by or system test modemin 3 · typ 6 · max 20 uA4
Bypass Capacitance CBATSystem Test (LDO) Mode; IOUT < 250 mAmin 1 uF4
Bypass Capacitance CBATSystem Test (LDO) Mode; IOUT > 250 mAmin 4.7 uF4
Die Temperature TSDThermal Shutdowntyp 150 °C5
Die Temperature Hysteresis TSDHYSThermal Shutdowntyp 10 °C5
UVLO Start Delay tSTARTVDD Low-to-Highmax 5 ms5
Transition Time Out of Preconditioning tDELAYVBAT<VPTH to VBAT>VPTHmax 1 ms5
Current Rise Time Out of Preconditioning tRISEIOUT Rising to 90% of IREGmax 1 ms5
Preconditioning Comparator Filter Time tPRECONAverage VBAT Rise/Fallmin 0.4 · typ 1.3 · max 3.2 ms5
Termination Comparator Filter Time tTERMAverage IOUT Fallingmin 0.4 · typ 1.3 · max 3.2 ms5
Charge Comparator Filter Time tCHARGEAverage VBAT Fallingmin 0.4 · typ 1.3 · max 3.2 ms5
Thermistor Comparator Filter Time tTHERMAverage THERM Rise/Fallmin 0.4 · typ 1.3 · max 3.2 ms5
Status Output turn-off tOFFISINK = 1 mA to 0 mAmax 200 us5
Status Output turn-on tONISINK = 0 mA to 1 mAmax 200 us5
Specified Temperature Range TAmin -40 · max 85 °C5
Operating Temperature Range TAmin -40 · max 125 °C5
Storage Temperature Range TAmin -65 · max 150 °C5
Thermal Resistance, MSOP-10 θJAMSOP-10; 4-Layer JC51-7 Standard Board, Natural Convectiontyp 113 °C/W5

Pins, by the datasheet

10
1 VDD
Battery Management Input Supply; bypass to VSS with a minimum of 1 uF. · p. 11
2 VDD
Battery Management Input Supply; bypass to VSS with a minimum of 1 uF. · p. 11
3 STAT1
Charge status output for an LED or a host microcontroller with a pull-up resistor. · p. 11
4 STAT2
Charge status output for an LED or a host microcontroller with a pull-up resistor. · p. 11
5 VSS
Battery Management 0V Reference; connect to negative terminals of battery and input supply. · p. 11
6 PROG
Current Regulation Set and Charge Control Enable; resistor to VSS sets currents; floating disables charging. · p. 11
7 PG
Pseudo open-drain power-good output; pull up only to the input supply because of its diode path to the input. · p. 11
8 THERM
Thermistor input with an internal 50 uA bias source for common 10 kΩ NTC thermistors. · p. 11
9 VBAT
Battery Charge Control Output; connect to battery positive and bypass to VSS with at least 1 uF. · p. 11
10 VBAT
Battery Charge Control Output; connect to battery positive and bypass to VSS with at least 1 uF. · p. 11

Open-source boards using it

2
  • 2 layers140 × 135 mmCompoudrier Bas, the printed circuit board in 3D

    Compoudrier Bas

    favsidv/createch_compoudrier

    Ce projet consiste à concevoir, sous KiCad, les cartes électroniques d'un Compoudrier inspiré de Totally Spies. L'objectif est de réunir un écran principal, des commandes de navigation et une horloge dans un objet…

    90 parts
  • 4 layers85 × 50 mmOpenHap, the printed circuit board in 3D

    OpenHap

    kenyattaejones32-boop/AQM

    Open-source hardware design for OpenHAP, an ESP32-based air quality monitor with CO sensing, thermistor temperature input, USB-C charging, and cellular data upload.

    269 parts

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the MCP73833-AMI/UN?

Yes. The symbol is dk_PMIC-Battery-Chargers:MCP73833-AMI_UN and the footprint Package_SO:MSOP-10_3x3mm_P0.5mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the MCP73833-AMI/UN?

MSOP-10, with 10 pins. Its footprint is drawn on this page.

Where is the MCP73833-AMI/UN datasheet?

Microchip Technology publishes it: the Datasheet link on this page opens it.

Where can I order the MCP73833-AMI/UN?

JLCPCB lists it as part C627668, with 151 in stock; the sellers' links on this page open their listings.

What can replace the MCP73833-AMI/UN?

Parts like it in the library: the CW1037CLCM by Cellwise, the CW1027CLCM by Cellwise, the CW1037CLEM by Cellwise and the LT3750EMS#PBF by Analog Devices. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the MCP73833-AMI/UN?

2 boards in 2 repositories on GitHub; the most starred are listed on this page, with their KiCad files.