Skip to the content
12345678

MCP4531-103E/MS

Microchip TechnologyExtended

-40℃~+125℃ 1 1.8V~5.5V 10kΩ 129 1LSB 1MHz 2.5uA 50ppm/℃ 75Ω I2C Linear Power-on reset RAM ±20% MSOP-8 Digital Potentiometers ROHS

Part id
microchip/MCP4531-103E/MS
Category
Digital Potentiometers
Package
MSOP-8
Pins
8
In stock
24 at JLCPCB (C150808)
Used on
1 open-source board

Overview

The MCP4531-103E/MS is a digital Potentiometer made by Microchip Technology in a MSOP-8 package with 8 pins. -40℃~+125℃ 1 1.8V~5.5V 10kΩ 129 1LSB 1MHz 2.5uA 50ppm/℃ 75Ω I2C Linear Power-on reset RAM ±20% MSOP-8 Digital Potentiometers ROHS.

PCBKit's library has its KiCad symbol (EasyEDA_Cloud:MCP4531-103E_MS, from EasyEDA) and its footprint (Package_SO:MSOP-8_3x3mm_P0.65mm, from KiCad's library), ready for a KiCad board. 24 are in stock at JLCPCB (part C150808). 1 open-source board in 1 repository on GitHub use it.

Symbol

1HVCA02SCL3SDA4VSS5P0A6P0W7P0B8VDD
EasyEDA_Cloud:MCP4531-103E_MSFrom EasyEDA

Footprint

12345678
Package_SO:MSOP-8_3x3mm_P0.65mmFrom KiCad's library

From the datasheet

14
Supply, least
2.7 V · VDD, recommended operating min · p. 4
Supply, most
5.5 V · VDD, recommended operating max · p. 4
Supply, least
1.8 V · VDD, serial interface only min · p. 4
Supply, most
2.7 V · VDD, serial interface only max · p. 4
Supply, absolute maximum
7 V · VDD, absolute max relative to VSS · p. 3
Works from
-40 °C · Operating ambient temperature min · p. 16
Works up to
125 °C · Operating ambient temperature max · p. 16
Junction, hottest
150 °C · Junction temperature absolute max · p. 3
Takes working
600 µA · VDD, serial interface active at 5.5 V and 3.4 MHz max · p. 4
Takes at most
600 µA · VDD, serial interface active at 5.5 V and 3.4 MHz max · p. 4
Takes asleep
2.5 µA · VDD, serial interface inactive at 5.5 V typical · p. 4
A pin gives at most
25 mA · Any output pin source current absolute max · p. 3
Junction to air (8L-MSOP)
211 K/W · Junction to ambient thermal resistance typical · p. 16
Data rate, most
3.4 Mbit/s · I2C high-speed mode at 4.5–5.5 V, Cb = 100 pF max · p. 13

What it is and has

13
Memory
Volatile · p. 1
Wiper operation
Zero-scale to full-scale · p. 1
Wiper resistance
75 Ω typical · p. 1
Interface
I2C · p. 1
I2C clock support
100 kHz, 400 kHz and 3.4 MHz · p. 1
Wiper commands
High-speed read/write · p. 1
Wiper commands
Increment/decrement · p. 1
Protection
Brown-out reset, 1.5 V typical · p. 1
Digital inputs
High-voltage tolerant up to 12.5 V · p. 1
Temperature range
-40°C to +125°C · p. 1
I2C addressing
7-bit slave addressing · p. 44
I2C multi-master
Supported · p. 44
General call addressing
Supported · p. 44

Specifications

146
ParameterConditionsAs printedPage
Voltage on VDD with respect to VSSmin -0.6 · max 7 V3
Voltage on HVC/A0, A1, A2, SCL, and SDA with respect to VSSmin -0.6 · max 12.5 V3
Voltage on all other pins (PxA, PxW, and PxB) with respect to VSSmin -0.3 V3
Maximum output current sunk by any Output pinmax 25 mA3
Maximum output current sourced by any Output pinmax 25 mA3
Maximum current out of VSS pinmax 100 mA3
Maximum current into VDD pinmax 100 mA3
Storage temperaturemin -65 · max 150 °C3
Ambient temperature with power appliedmin -40 · max 125 °C3
Package power dissipationMSSOP-8; TA = +50°C, TJ = +150°Cmax 473 mW3
Soldering temperature of leads10 secondsmax 300 °C3
Maximum Junction Temperature TJmax 150 °C3
Supply Voltage VDDmin 2.7 · max 5.5 V4
Supply Voltage VDDSerial Interface only.min 1.8 · max 2.7 V4
HVC pin Voltage Range VHVVDD ≥ 4.5V; Note 6max 12.5 V4
VDD Start Voltage to ensure Wiper Reset VBORRAM retention voltage (VRAM) < VBORmax 1.65 V4
Delay after device exits the reset state (VDD > VBOR) TBORDtyp 10 · max 20 us4
Supply Current IDDSerial Interface Active; HVC/A0 = VIH (or VIL); write all 0’s to Volatile Wiper 0; VDD = 5.5V, FSCL = 3.4 MHz; Notes 10, 11max 600 uA4
Supply Current IDDSerial Interface Active; HVC/A0 = VIH (or VIL); write all 0’s to Volatile Wiper 0; VDD = 5.5V, FSCL = 100 kHz; Notes 10, 11max 250 uA4
Supply Current IDDSerial Interface Inactive; Stop condition, SCL = SDA = VIH; Wiper = 0; VDD = 5.5V, HVC/A0 = VIH; Note 10typ 2.5 · max 5 uA4
Resistance (± 20%) RAB-103 devices; Note 1min 8 · typ 10 · max 12 k5
Resolution N7-bit; No Missing Codestyp 129 Taps5
Wiper Resistance RWVDD = 5.5 V, IW = 2.0 mA, code = 00h; MCP4XX1; Note 3typ 75 · max 160 5
Wiper Resistance RWVDD = 2.7 V, IW = 2.0 mA, code = 00h; MCP4XX1; Note 3typ 75 · max 300 5
Nominal Resistance Tempco RAB/TTA = -20°C to +70°Ctyp 50 ppm/°C5
Nominal Resistance Tempco RAB/TTA = -40°C to +85°Ctyp 100 ppm/°C5
Nominal Resistance Tempco RAB/TTA = -40°C to +125°Ctyp 150 ppm/°C5
Ratiometeric Tempco VWB/TCode = Midscale (40h), 7-bittyp 15 ppm/°C5
Maximum current through Terminal (A, W or B) ITTerminal A; IAW, W = Full-Scale (FS); Note 6max 2.5 mA6
Maximum current through Terminal (A, W or B) ITTerminal B; IBW, W = Zero Scale (ZS); Note 6max 2.5 mA6
Maximum current through Terminal (A, W or B) ITTerminal W; IAW or IBW, W = FS or ZS; Note 6max 2.5 mA6
Maximum current through Terminal (A, W or B) IT10 k; Terminal A and Terminal B; IAB, VB = 0V, VA = 5.5V, RAB(MIN) = 8000; Note 6max 0.688 mA6
Leakage current into A, W or B IWLMCP4XX1 PxA = PxW = PxB = VSStyp 100 nA6
Leakage current into A, W or B IWLTerminals Disconnected (R1HW = R0HW = 0)typ 100 nA6
Full-Scale Error (MCP4XX1 only) VWFSE10 k, 7-bit code = 80h; 3.0V ≤ VDD ≤ 5.5Vmin -2 · typ -0.1 LSb7
Zero-Scale Error (MCP4XX1 only) VWZSE10 k, 7-bit code = 00h; 3.0V ≤ VDD ≤ 5.5Vtyp 0.1 · max 2 LSb7
Potentiometer Integral Non-linearity INL7-bit; 3.0V ≤ VDD ≤ 5.5V; MCP4XX1 devices only (Note 2)min -0.5 · max 0.5 LSb7
Potentiometer Differential Non-linearity DNL7-bit; 3.0V ≤ VDD ≤ 5.5V; MCP4XX1 devices only (Note 2)min -0.25 · max 0.25 LSb7
Bandwidth -3 dB BW10 k, 7-bit, Code = 40h; See Figure 2-65, load = 30 pFtyp 1 MHz8
Rheostat Integral Non-linearity R-INLMCP45X1 externally connected for rheostat testing; 10 k, 7-bit; 5.5V, IW = 450 uA; Note 8min -1.125 · max 1.125 LSb9
Rheostat Integral Non-linearity R-INLMCP45X1 externally connected for rheostat testing; 10 k, 7-bit; 3.0V, IW = 240 uA; Notes 7, 8min -4 · typ 2.5 · max 4 LSb9
Rheostat Differential Non-linearity R-DNLMCP45X1 externally connected for rheostat testing; 10 k, 7-bit; 5.5V, IW = 450 uA; Note 8min -0.375 · max 0.375 LSb10
Rheostat Differential Non-linearity R-DNLMCP45X1 externally connected for rheostat testing; 10 k, 7-bit; 3.0V, IW = 240 uA; Notes 7, 8min -0.75 · typ 0.5 · max 0.75 LSb10
Capacitance (PA) CAWf =1 MHz, Code = Full-Scaletyp 75 pF10
Capacitance (Pw) CWf =1 MHz, Code = Full-Scaletyp 120 pF10
Capacitance (PB) CBWf =1 MHz, Code = Full-Scaletyp 75 pF10
Schmitt Trigger Low Input Threshold VILSDA and SCL; 100 kHzmin -0.5 V11
Schmitt Trigger Low Input Threshold VILSDA and SCL; 400 kHzmin -0.5 V11
Schmitt Trigger Low Input Threshold VILSDA and SCL; 1.7 MHzmin -0.5 V11
Schmitt Trigger Low Input Threshold VILSDA and SCL; 3.4 Mhzmin -0.5 V11
High Voltage Limit VMAXPin can tolerate VMAX or less; Note 6max 12.5 V11
Output Low Voltage (SDA) VOLVDD ≥ 2.0V, IOL = 3 mAmax 0.4 V12
Weak Pull-up / Pull-down Current IPUInternal VDD pull-up, VIHH pull-down; VDD = 5.5V, VIHH = 12.5Vmax 1.75 mA12
Weak Pull-up / Pull-down Current IPUHVC pin, VDD = 5.5V, VHVC = 3Vtyp 170 uA12
HVC Pull-up / Pull-down Resistance RHVCVDD = 5.5V, VHVC = 3Vtyp 16 k12
Input Leakage Current IILVIN = VDD and VIN = VSSmin -1 · max 1 uA12
Pin Capacitance CIN, COUTfC = 3.4 MHztyp 10 pF12
Standard Mode FSCLCb = 400 pF, 1.8V - 5.5Vmin 0 · max 100 kHz13
Fast Mode FSCLCb = 400 pF, 2.7V - 5.5Vmin 0 · max 400 kHz13
High-Speed 1.7 FSCLCb = 400 pF, 4.5V - 5.5Vmin 0 · max 1.7 MHz13
High-Speed 3.4 FSCLCb = 100 pF, 4.5V - 5.5Vmin 0 · max 3.4 MHz13
Bus capacitive loading Cb100 kHz modemax 400 pF13
Bus capacitive loading Cb400 kHz modemax 400 pF13
Bus capacitive loading Cb1.7 MHz modemax 400 pF13
Bus capacitive loading Cb3.4 MHz modemax 100 pF13
START condition Setup time TSU:STA100 kHz mode; Only relevant for repeated START conditionmin 4700 ns13
START condition Setup time TSU:STA400 kHz mode; Only relevant for repeated START conditionmin 600 ns13
START condition Setup time TSU:STA1.7 MHz mode; Only relevant for repeated START conditionmin 160 ns13
START condition Setup time TSU:STA3.4 MHz mode; Only relevant for repeated START conditionmin 160 ns13
START condition Hold time THD:STA100 kHz mode; After this period the first clock pulse is generatedmin 4000 ns13
START condition Hold time THD:STA400 kHz mode; After this period the first clock pulse is generatedmin 600 ns13
START condition Hold time THD:STA1.7 MHz modemin 160 ns13
START condition Hold time THD:STA3.4 MHz modemin 160 ns13
STOP condition Setup time TSU:STO100 kHz modemin 4000 ns13
STOP condition Setup time TSU:STO400 kHz modemin 600 ns13
STOP condition Setup time TSU:STO1.7 MHz modemin 160 ns13
STOP condition Setup time TSU:STO3.4 MHz modemin 160 ns13
STOP condition Hold time THD:STO100 kHz modemin 4000 ns13
STOP condition Hold time THD:STO400 kHz modemin 600 ns13
STOP condition Hold time THD:STO1.7 MHz modemin 160 ns13
STOP condition Hold time THD:STO3.4 MHz modemin 160 ns13
Clock high time THIGH100 kHz mode; 1.8V-5.5Vmin 4000 ns14
Clock high time THIGH400 kHz mode; 2.7V-5.5Vmin 600 ns14
Clock high time THIGH1.7 MHz mode; 4.5V-5.5Vmin 120 ns14
Clock high time THIGH3.4 MHz mode; 4.5V-5.5Vmin 60 ns14
Clock low time TLOW100 kHz mode; 1.8V-5.5Vmin 4700 ns14
Clock low time TLOW400 kHz mode; 2.7V-5.5Vmin 1300 ns14
Clock low time TLOW1.7 MHz mode; 4.5V-5.5Vmin 320 ns14
Clock low time TLOW3.4 MHz mode; 4.5V-5.5Vmin 160 ns14
SCL rise time TRSCL100 kHz mode; Cb = 10 to 400 pF; Note 5max 1000 ns14
SCL rise time TRSCL400 kHz mode; Cb = 10 to 400 pF; Notes 3, 5max 300 ns14
SCL rise time TRSCL1.7 MHz mode; Cb = 10 to 400 pF; Note 5min 20 · max 80 ns14
SCL rise time TRSCL1.7 MHz mode; After a Repeated Start condition or an Acknowledge bit; Note 5min 20 · max 160 ns14
SCL rise time TRSCL3.4 MHz mode; Cb = 10 to 100 pF; Note 5min 10 · max 40 ns14
SCL rise time TRSCL3.4 MHz mode; After a Repeated Start condition or an Acknowledge bit; Note 5min 10 · max 80 ns14
SDA rise time TRSDA100 kHz mode; Cb = 10 to 400 pF; Note 5max 1000 ns14
SDA rise time TRSDA400 kHz mode; Cb = 10 to 400 pF; Notes 3, 5max 300 ns14
SDA rise time TRSDA1.7 MHz mode; Cb = 10 to 400 pF; Note 5min 20 · max 160 ns14
SDA rise time TRSDA3.4 MHz mode; Cb = 10 to 100 pF; Note 5min 10 · max 80 ns14
SCL fall time TFSCL100 kHz mode; Cb = 10 to 400 pF; Note 5max 300 ns14
SCL fall time TFSCL400 kHz mode; Cb = 10 to 400 pF; Notes 3, 5max 300 ns14
SCL fall time TFSCL1.7 MHz mode; Cb = 10 to 400 pF; Note 5min 20 · max 80 ns14
SCL fall time TFSCL3.4 MHz mode; Cb = 10 to 100 pF; Note 5min 10 · max 40 ns14
Specified Temperature Range TAVDD = +2.7V to +5.5V, VSS = GNDmin -40 · max 125 °C16
Operating Temperature Range TAVDD = +2.7V to +5.5V, VSS = GNDmin -40 · max 125 °C16
Storage Temperature Range TAmin -65 · max 150 °C16
Thermal Resistance, 8L-MSOP JA8L-MSOPtyp 211 °C/W16
SCL rise time TRSCL100 kHz mode; Cb from 10 to 400 pF; Note 5max 1000 ns14
SCL rise time TRSCL400 kHz mode; minimum = 20 + 0.1Cb; Cb from 10 to 400 pF; Note 5max 300 ns14
SCL rise time TRSCL1.7 MHz mode; Note 5min 20 · max 80 ns14
SCL rise time TRSCL1.7 MHz mode; after a Repeated Start condition or an Acknowledge bit; Note 5min 20 · max 160 ns14
SCL rise time TRSCL3.4 MHz mode; Cb from 10 to 100 pF; Note 5min 10 · max 40 ns14
SCL rise time TRSCL3.4 MHz mode; after a Repeated Start condition or an Acknowledge bit; Cb from 10 to 100 pF; Note 5min 10 · max 80 ns14
SDA rise time TRSDA100 kHz mode; Cb from 10 to 400 pF; Note 5max 1000 ns14
SDA rise time TRSDA400 kHz mode; minimum = 20 + 0.1Cb; Cb from 10 to 400 pF; Note 5max 300 ns14
SDA rise time TRSDA1.7 MHz mode; Note 5min 20 · max 160 ns14
SDA rise time TRSDA3.4 MHz mode; Cb from 10 to 100 pF; Note 5min 10 · max 80 ns14
SCL fall time TFSCL100 kHz mode; Cb from 10 to 400 pF; Note 5max 300 ns14
SCL fall time TFSCL400 kHz mode; minimum = 20 + 0.1Cb; Cb from 10 to 400 pF; Note 5max 300 ns14
SCL fall time TFSCL1.7 MHz mode; Note 5min 20 · max 80 ns14
SCL fall time TFSCL3.4 MHz mode; Cb from 10 to 100 pF; Note 5min 10 · max 40 ns14
SDA fall time TFSDA100 kHz mode; Cb from 10 to 400 pF; Note 5max 300 ns15
SDA fall time TFSDA400 kHz mode; minimum = 20 + 0.1Cb; Cb from 10 to 400 pF; Notes 3 and 5max 300 ns15
SDA fall time TFSDA1.7 MHz mode; Note 5min 20 · max 160 ns15
SDA fall time TFSDA3.4 MHz mode; Cb from 10 to 100 pF; Note 5min 10 · max 80 ns15
Data input hold time THD:DAT100 kHz mode; 1.8V-5.5V; Note 5min 0 ns15
Data input hold time THD:DAT400 kHz mode; 2.7V-5.5V; Note 5min 0 ns15
Data input hold time THD:DAT1.7 MHz mode; 4.5V-5.5V; Note 5min 0 ns15
Data input hold time THD:DAT3.4 MHz mode; 4.5V-5.5V; Note 5min 0 ns15
Data input setup time TSU:DAT100 kHz mode; Note 2min 250 ns15
Data input setup time TSU:DAT400 kHz modemin 100 ns15
Data input setup time TSU:DAT1.7 MHz modemin 10 ns15
Data input setup time TSU:DAT3.4 MHz modemin 10 ns15
Output valid from clock TAA100 kHz mode; Note 1max 3450 ns15
Output valid from clock TAA400 kHz modemax 900 ns15
Output valid from clock TAA1.7 MHz mode; Cb = 100 pF; Notes 1 and 6max 150 ns15
Output valid from clock TAA1.7 MHz mode; Cb = 400 pF; Notes 1 and 4max 310 ns15
Output valid from clock TAA3.4 MHz mode; Cb = 100 pF; Note 1max 150 ns15
Bus free time TBUF100 kHz mode; time the bus must be free before a new transmission can startmin 4700 ns15
Bus free time TBUF400 kHz mode; time the bus must be free before a new transmission can startmin 1300 ns15
Input filter spike suppression (SDA and SCL) TSP100 kHz mode; Philips Spec states N.A.max 50 ns15
Input filter spike suppression (SDA and SCL) TSP400 kHz modemax 50 ns15
Input filter spike suppression (SDA and SCL) TSP1.7 MHz mode; spike suppressionmax 10 ns15
Input filter spike suppression (SDA and SCL) TSP3.4 MHz mode; spike suppressionmax 10 ns15
Specified Temperature Range TAUnless otherwise indicated, VDD = +2.7V to +5.5V, VSS = GNDmin -40 · max 125 °C16
Operating Temperature Range TAUnless otherwise indicated, VDD = +2.7V to +5.5V, VSS = GNDmin -40 · max 125 °C16

Pins, by the datasheet

8
1 HVC / A0
High-voltage command / address 0. · p. 1
2 SCL
I2C serial clock. · p. 1
3 SDA
I2C serial data. · p. 1
4 VSS
Ground. · p. 1
5 P0A
Potentiometer 0 terminal A. · p. 1
6 P0W
Potentiometer 0 wiper. · p. 1
7 P0B
Potentiometer 0 terminal B. · p. 1
8 VDD
Supply voltage. · p. 1

Open-source boards using it

1
  • 4 layers200 × 100 mmMinUS, the printed circuit board in 3D

    MinUS

    kelu124/minus

    Minimal ultrasound platform

    222 parts3

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the MCP4531-103E/MS?

Yes. The symbol is EasyEDA_Cloud:MCP4531-103E_MS and the footprint Package_SO:MSOP-8_3x3mm_P0.65mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the MCP4531-103E/MS?

MSOP-8, with 8 pins. Its footprint is drawn on this page.

Where is the MCP4531-103E/MS datasheet?

Microchip Technology publishes it: the Datasheet link on this page opens it.

Where can I order the MCP4531-103E/MS?

JLCPCB lists it as part C150808, with 24 in stock; the sellers' links on this page open their listings.

What can replace the MCP4531-103E/MS?

Parts like it in the library: the CAT5115ZI-10-GT3 by onsemi, the MCP4551-502E/MS by Microchip Technology, the MCP4551-103E/MS by Microchip Technology and the MCP4021-202E/MS by Microchip Technology. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the MCP4531-103E/MS?

1 board in 1 repository on GitHub; the most starred are listed on this page, with their KiCad files.