
MCP4131-104E/SN
Microchip TechnologyExtended
-40℃~+125℃ 1 1.8V~5.5V 100kHz 100kΩ 129 2.5uA 50ppm/℃ 75Ω Linear Power-on reset RAM SPI ±20% SOIC-8 Digital Potentiometers ROHS
- Part id
- microchip/MCP4131-104E/SN
- Category
- Digital Potentiometers
- Package
- SOIC-8
- Pins
- 8
- In stock
- 118 at JLCPCB (C636034)
- Used on
- 2 open-source boards
Overview
The MCP4131-104E/SN is a digital Potentiometer made by Microchip Technology in a SOIC-8 package with 8 pins. -40℃~+125℃ 1 1.8V~5.5V 100kHz 100kΩ 129 2.5uA 50ppm/℃ 75Ω Linear Power-on reset RAM SPI ±20% SOIC-8 Digital Potentiometers ROHS.
PCBKit's library has its KiCad symbol (EasyEDA_Cloud:MCP4161-502E_SN, from EasyEDA) and its footprint (Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, from KiCad's library), ready for a KiCad board. 118 are in stock at JLCPCB (part C636034). 2 open-source boards in 2 repositories on GitHub use it.
Symbol
Footprint
From the datasheet
13- Supply, least
- 2.7 V · VDD, recommended operating min, specified characteristics · p. 4
- Supply, most
- 5.5 V · VDD, recommended operating max, specified characteristics · p. 4
- Supply, least
- 1.8 V · VDD, serial interface only min · p. 4
- Supply, most
- 2.7 V · VDD, serial interface only max · p. 4
- Supply, absolute maximum
- 7 V · VDD, absolute max relative to VSS · p. 3
- Works from
- -40 °C · Operating ambient min · p. 14
- Works up to
- 125 °C · Operating ambient max · p. 14
- Junction, hottest
- 150 °C · Junction temperature absolute max · p. 3
- Takes working
- 450 µA · IDD max, interface active, VDD = 5.5V, CS = VIL, SCK = 5 MHz · p. 4
- Takes at most
- 1 mA · IDD max, VDD = 5.5V, CS = VIHH, SCK = 5 MHz · p. 4
- Takes asleep
- 2.5 µA · IDD typical, interface inactive, CS = VIH, VDD = 5.5V · p. 4
- A pin gives at most
- 25 mA · Digital output source or sink absolute max · p. 3
- Junction to air (8L-SOIC)
- 149.5 K/W · Junction to ambient typical · p. 14
What it is and has
8- Resolution
- 7-bit, 128 resistors, 129 steps · p. 1
- Resistance
- 100 kΩ nominal, ±20% · p. 5
- Interface
- SPI, 10 MHz, modes 0,0 and 1,1 · p. 1
- Serial data
- Multiplexed SDI/SDO · p. 1
- Wiper range
- Zero scale to full scale · p. 1
- Protection
- Brown-out reset, 1.5V typical · p. 1
- Digital inputs
- Internal weak pull-up · p. 1
- Split rail
- Supported · p. 1
Specifications
54| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Voltage on VDD with respect to VSS VDD | min -0.6 · max 7 V | 3 | |
| Voltage on CS, SCK, SDI, SDI/SDO, and SHDN with respect to VSS | min -0.6 · max 12.5 V | 3 | |
| Voltage on all other pins (PxA, PxW, PxB, and SDO) with respect to VSS | Maximum VDD + 0.3V | min -0.3 V | 3 |
| Maximum output current sunk by any Output pin | max 25 mA | 3 | |
| Maximum output current sourced by any Output pin | max 25 mA | 3 | |
| Maximum current out of VSS pin | max 100 mA | 3 | |
| Maximum current into VDD pin | max 100 mA | 3 | |
| Storage temperature | min -65 · max 150 °C | 3 | |
| Ambient temperature with power applied | min -40 · max 125 °C | 3 | |
| Total power dissipation | Note 1 | max 400 mW | 3 |
| Soldering temperature of leads | 10 seconds | max 300 °C | 3 |
| ESD protection on all pins | HBM | min 4 kV | 3 |
| ESD protection on all pins | MM | min 300 V | 3 |
| Maximum Junction Temperature TJ | max 150 °C | 3 | |
| Supply Voltage VDD | Specified characteristics | min 2.7 · max 5.5 V | 4 |
| Supply Voltage VDD | Serial Interface only. | min 1.8 · max 2.7 V | 4 |
| CS, SDI, SDO, SCK, SHDN pin Voltage Range VHV | VDD ≥ 4.5V; minimum VSS; Note 6 | max 12.5 V | 4 |
| VDD Start Voltage to ensure Wiper Reset VBOR | RAM retention voltage (VRAM) < VBOR | max 1.65 V | 4 |
| Delay after device exits the reset state (VDD > VBOR) TBORD | typ 10 · max 20 us | 4 | |
| Supply Current IDD | Serial Interface Active, VDD = 5.5V, CS = VIL, SCK @ 5 MHz, write all 0’s to volatile Wiper 0 (address 0h); Note 10 | max 450 uA | 4 |
| Supply Current IDD | Serial Interface Inactive, CS = VIH, VDD = 5.5V; Note 10 | typ 2.5 · max 5 uA | 4 |
| Supply Current IDD | Serial Interface Active, VDD = 5.5V, CS = VIHH, SCK @ 5 MHz, decrement volatile Wiper 0 (address 0h); Note 10 | typ 0.55 · max 1 mA | 4 |
| Resistance (± 20%) RAB | -104 devices (Note 1) | min 80 · typ 100 · max 120 kΩ | 5 |
| Resolution N | 7-bit No Missing Codes | typ 129 Taps | 5 |
| Wiper Resistance RW | VDD = 5.5 V, IW = 2.0 mA, code = 00h; MCP4XX1 | typ 75 · max 160 Ω | 5 |
| Wiper Resistance RW | VDD = 2.7 V, IW = 2.0 mA, code = 00h; MCP4XX1 | typ 75 · max 300 Ω | 5 |
| Nominal Resistance Tempco ΔRAB/ΔT | TA = -20°C to +70°C | typ 50 ppm/°C | 5 |
| Nominal Resistance Tempco ΔRAB/ΔT | TA = -40°C to +85°C | typ 100 ppm/°C | 5 |
| Nominal Resistance Tempco ΔRAB/ΔT | TA = -40°C to +125°C | typ 150 ppm/°C | 5 |
| Ratiometeric Tempco ΔVWB/ΔT | Code = Midscale (40h for 7-bit) | typ 15 ppm/°C | 5 |
| Maximum current through A, W or B IW | Note 6, Worst case current through wiper when wiper is either Full-Scale or Zero Scale. | max 2.5 mA | 5 |
| Leakage current into A, W or B IWL | MCP4XX1 PxA = PxW = PxB = VSS | typ 100 nA | 5 |
| Full-Scale Error VWFSE | MCP4XX1; 100 kΩ, 7-bit code = 80h; 3.0V ≤ VDD ≤ 5.5V | min -0.5 · typ -0.1 LSb | 6 |
| Zero-Scale Error VWZSE | MCP4XX1; 100 kΩ, 7-bit code = 00h; 3.0V ≤ VDD ≤ 5.5V | typ 0.1 · max 0.5 LSb | 6 |
| Potentiometer Integral Non-linearity INL | 7-bit; MCP4XX1 devices only; 3.0V ≤ VDD ≤ 5.5V; Note 2; typical ±0.25 | min -0.5 · max 0.5 LSb | 6 |
| Potentiometer Differential Non-linearity DNL | 7-bit; MCP4XX1 devices only; 3.0V ≤ VDD ≤ 5.5V; Note 2; typical ±0.125 | min -0.25 · max 0.25 LSb | 6 |
| Bandwidth -3 dB BW | 100 kΩ, 7-bit, Code = 40h; load = 30 pF; See Figure 2-64 | typ 100 kHz | 6 |
| Rheostat Integral Non-linearity R-INL | MCP41X1; 100 kΩ, 7-bit; 5.5V, IW = 45 uA; Note 4, Note 8; typical ±0.5 | min -0.8 · max 0.8 LSb | 7 |
| Rheostat Integral Non-linearity R-INL | MCP41X1; 100 kΩ, 7-bit; 3.0V, IW = 24 uA; Note 4, Note 7, Note 8 | min -1.125 · typ 0.25 · max 1.125 LSb | 7 |
| Rheostat Differential Non-linearity R-DNL | MCP41X1; 100 kΩ, 7-bit; 5.5V, IW = 45 uA; Note 4, Note 8; typical ±0.25 | min -0.375 · max 0.375 LSb | 8 |
| Rheostat Differential Non-linearity R-DNL | MCP41X1; 100 kΩ, 7-bit; 3.0V; Note 4, Note 7, Note 8; typical ±0.25 | min -0.375 · max 0.375 LSb | 8 |
| Capacitance (PA) CAW | f =1 MHz, Code = Full-Scale | typ 75 pF | 8 |
| Capacitance (Pw) CW | f =1 MHz, Code = Full-Scale | typ 120 pF | 8 |
| Capacitance (PB) CBW | f =1 MHz, Code = Full-Scale | typ 75 pF | 8 |
| High Voltage Limit VMAX | Pin can tolerate VMAX or less; Note 6 | max 12.5 V | 9 |
| Weak Pull-up / Pull-down Current IPU | Internal VDD pull-up, VIHH pull-down, VDD = 5.5V, VCS = 12.5V | max 1.75 mA | 9 |
| Weak Pull-up / Pull-down Current IPU | CS pin, VDD = 5.5V, VCS = 3V | typ 170 uA | 9 |
| CS Pull-up / Pull-down Resistance RCS | VDD = 5.5V, VCS = 3V | typ 16 kΩ | 9 |
| Input Leakage Current IIL | VIN = VDD and VIN = VSS | min -1 · max 1 uA | 9 |
| Pin Capacitance CIN, COUT | fC = 20 MHz | typ 10 pF | 9 |
| Specified Temperature Range TA | VDD = +2.7V to +5.5V, VSS = GND | min -40 · max 125 °C | 14 |
| Operating Temperature Range TA | VDD = +2.7V to +5.5V, VSS = GND | min -40 · max 125 °C | 14 |
| Storage Temperature Range TA | min -65 · max 150 °C | 14 | |
| Thermal Resistance, 8L-SOIC θJA | 8L-SOIC | typ 149.5 °C/W | 14 |
Pins, by the datasheet
8- 1 CS
- SPI Chip Select Input. · p. 31
- 2 SCK
- SPI Clock Input. · p. 31
- 3 SDI/SDO
- SPI Serial Data Input/Output; the output is open drain with an internal smart pull-up. · p. 31
- 4 VSS
- Ground. · p. 31
- 5 P0A
- Potentiometer 0 Terminal A. · p. 31
- 6 P0W
- Potentiometer 0 Wiper Terminal. · p. 31
- 7 P0B
- Potentiometer 0 Terminal B. · p. 31
- 8 VDD
- Positive Power Supply Input. · p. 31
Open-source boards using it
2- 4 layers200 × 100 mm

- 4 layers80 × 60 mm

Kcell faker
karlp/kcell-faker
fake a load cell, for testing functional behaviour with changing loads.
75 parts
Parts like it
8MCP41010-I/SN
SOIC-8-150mil-40℃~+85℃ 1 10kΩ 10nA 1LSB 1MHz 2.7V~5.5V 256 800ppm/℃ Linear Power-on reset SPI ±1% SOIC-8 Digital Potentiometers ROHSMicrochip TechnologyDigital PotentiometersX9C103SIZT1
SOIC-8-40℃~+85℃ 1 100 10kΩ 200uA 40Ω、100Ω 5V Non-volatile storage、Power-on reset U/D nvRAM ±20% ±300ppm/℃ SOIC-8 Digital Potentiometers ROHSRenesas ElectronicsDigital PotentiometersX9C503SIZT1
SOIC-8-40℃~+85℃ 1 100 200uA 4.5V~5.5V 40Ω 50kΩ Linear Non-volatile storage U/D ±20% ±300ppm/℃ SOIC-8 Digital Potentiometers ROHSRenesas ElectronicsDigital PotentiometersMCP4011-103E/SN
SOIC-8-40℃~+125℃ 0.5LSB 1 1.8V~5.5V 10kΩ 1MHz 1uA 50ppm/℃ 64 70Ω Linear Power-on reset RAM U/D ±20% SOIC-8 Digital Potentiometers ROHSMicrochip TechnologyDigital PotentiometersX9C102SIZ
SOIC-8-40℃~+85℃ 1 100 1kΩ 4.5V~5.5V 750uA EEPROM Linear U/D ±20% ±600ppm/℃ SOIC-8 Digital Potentiometers ROHSRenesas ElectronicsDigital PotentiometersMCP41050-I/SN
SOIC-8-40℃~+85℃ 1 10nA 125Ω 1LSB 2.7V~5.5V 256 280MHz 50kΩ 800ppm/℃ Linear Power-on reset SPI ±1% SOIC-8 Digital Potentiometers ROHSMicrochip TechnologyDigital PotentiometersAD8400ARZ10-REEL
SOIC-8-40℃~+125℃ 1 10kΩ 10nA 2.7V~5.5V 256 500ppm/℃ 50Ω、200Ω 600kHz Linear SPI Soft reset ±20% SOIC-8 Digital Potentiometers ROHSAnalog DevicesDigital PotentiometersMCP4161-502E/SN
SOIC-8-40℃~+125℃ 1 15ppm/℃ 2.5uA 2.7V~5.5V 257 2MHz 5kΩ 75Ω EEPROM Linear Non-volatile storage、Power-on reset、Slide lock SPI ±20% SOIC-8 Digital Potentiometers ROHSMicrochip TechnologyDigital Potentiometers
Questions
Is there a KiCad symbol and footprint for the MCP4131-104E/SN?
Yes. The symbol is EasyEDA_Cloud:MCP4161-502E_SN and the footprint Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the MCP4131-104E/SN?
SOIC-8, with 8 pins. Its footprint is drawn on this page.
Where is the MCP4131-104E/SN datasheet?
Microchip Technology publishes it: the Datasheet link on this page opens it.
Where can I order the MCP4131-104E/SN?
JLCPCB lists it as part C636034, with 118 in stock; the sellers' links on this page open their listings.
What can replace the MCP4131-104E/SN?
Parts like it in the library: the MCP41010-I/SN by Microchip Technology, the X9C103SIZT1 by Renesas Electronics, the X9C503SIZT1 by Renesas Electronics and the MCP4011-103E/SN by Microchip Technology. Check their datasheets: a part that fits the footprint may still differ in its ratings.
Which open-source boards use the MCP4131-104E/SN?
2 boards in 2 repositories on GitHub; the most starred are listed on this page, with their KiCad files.