Skip to the content
12345678

MCP1642B-33I/MS

Microchip TechnologyExtended

-40℃~+85℃@(TA) 1 1MHz 3.3V 650mV~5.5V 800mA Boost Boost Built-in Fixed Yes MSOP-8 DC-DC Converters ROHS

Part id
microchip/MCP1642B-33I/MS
Category
DC DC Converters
Package
MSOP-8
Pins
8
In stock
31 at JLCPCB (C635907)
Used on
2 open-source boards

Overview

The MCP1642B-33I/MS is a DC DC Converter made by Microchip Technology in a MSOP-8 package with 8 pins. -40℃~+85℃@(TA) 1 1MHz 3.3V 650mV~5.5V 800mA Boost Boost Built-in Fixed Yes MSOP-8 DC-DC Converters ROHS.

PCBKit's library has its KiCad symbol (EasyEDA_Cloud:MCP1642BT-18I_MS, from EasyEDA) and its footprint (Package_SO:MSOP-8_3x3mm_P0.65mm, from KiCad's library), ready for a KiCad board. 31 are in stock at JLCPCB (part C635907). 2 open-source boards in 1 repository on GitHub use it.

Symbol

1EN2NC3PG4VOUT5SW6PGND7SGND8VIN
EasyEDA_Cloud:MCP1642BT-18I_MSFrom EasyEDA

Footprint

12345678
Package_SO:MSOP-8_3x3mm_P0.65mmFrom KiCad's library

From the datasheet

12
Supply, absolute maximum
6.5 V · VIN, absolute maximum · p. 3
Works from
-40 °C · ambient with power applied, min · p. 3
Works up to
85 °C · ambient with power applied, max · p. 3
Junction, hottest
125 °C · operating junction temperature, max · p. 3
Junction, hottest
150 °C · junction temperature, transient max · p. 5
Takes working
400 µA · VOUT quiescent current, PWM mode, typical; externally supplied output, no switching, no load · p. 4
Takes asleep
1 µA · shutdown current, typical; VOUT = EN = GND, no load · p. 4
Gives
300 mA · maximum output current, typical; VIN = 1.5V, VOUT = 3.3V · p. 3
Current limit
1.8 A · NMOS peak switch current limit, typical · p. 4
Output
3.3 V · MCP1642B-33 fixed output, typical; VIN < 3.3V · p. 3
Switches at
1 MHz · switching frequency, typical; IOUT = 65 mA · p. 5
Junction to air (8L-MSOP)
211 K/W · junction to ambient thermal resistance, typical · p. 5

What it is and has

9
Efficiency
Up to 96% typical · p. 1
Switching
1 MHz PWM operation · p. 1
Power Good
Open-drain output · p. 1
Rectifier
Internal synchronous rectifier · p. 1
Compensation
Internal · p. 1
Protection
Inrush current limiting and internal soft-start · p. 1
Shutdown
True load disconnect · p. 1
Protection
Overtemperature protection · p. 1
Package
8-lead MSOP · p. 1

Around it

2
cap 4.7 µF
between VIN and GND; Minimum input bypass capacitance. · p. 11
res high-value resistor
between PG and VOUT; External pull-up for the open-drain Power Good output; use a high value to reduce power consumption. · p. 17

Specifications

39
ParameterConditionsAs printedPage
EN, FB, VIN, VSW, VOUT – GNDmax 6.5 V3
Storage Temperaturemin -65 · max 150 °C3
Ambient Temp. with Power Appliedmin -40 · max 85 °C3
Operating Junction Temperaturemin -40 · max 125 °C3
ESD Protection On All Pins: HBMAll pinsmax 4 kV3
ESD Protection On All Pins: MMAll pinsmax 300 V3
Minimum Start-Up Voltage VINNote 1: resistive load, 1 mAtyp 0.65 · max 0.8 V3
Minimum Input Voltage After Start-Up VINNote 1: resistive load, 1 mA; Note 5: determined by characterization, not production testedtyp 0.35 V3
Output Voltage (MCP1642B/D-XX) VOUTVIN < 3.3V, MCP1642B/D-33, Note 2typ 3.3 V3
Maximum Output Current IOUT1.5V VIN, 3.3V VOUT, Note 5typ 300 mA3
Quiescent Current – PWM Mode IQPWMMeasured at VOUT, EN = VIN, IOUT = 0 mA, Note 3; externally supplied VOUT, device not switchingtyp 400 · max 500 uA4
Quiescent Current – Shutdown IQSHDNVOUT = EN = GND, IOUT = 0 mA; includes N-Channel and P-Channel Switch Leakagetyp 1 uA4
NMOS Switch Leakage INLKVIN = VSW = 5V, VOUT = 5.5V, VEN = VFB = GNDtyp 0.5 uA4
PMOS Switch Leakage IPLKVIN = VSW = GND, VOUT = 5.5Vtyp 0.2 uA4
NMOS Switch ON Resistance RDS(ON)NVIN = 3.3V, ISW = 250 mA, Note 5typ 0.15 4
PMOS Switch ON Resistance RDS(ON)PVIN = 3.3V, ISW = 250 mA, Note 5typ 0.3 4
NMOS Peak Switch Current Limit IN(MAX)Note 5typ 1.8 A4
Accuracy VOUT%MCP1642B/D-33, VIN = 1.2Vmin -3 · max 3 %4
Line Regulation VOUT/VOUT)/VIN|MCP1642B/D-33, VIN = 1.5V to 3.0V, IOUT = 25 mAmin -0.5 · typ 0.01 · max 0.5 %/V4
Load Regulation VOUT/VOUT|MCP1642B/D-33, VIN = 1.5V, IOUT = 25 mA to 150 mAmin -1.5 · typ 0.1 · max 1.5 %4
Maximum Duty Cycle DCMAXNote 5typ 90 %5
Switching Frequency fSWNote 5, IOUT = 65 mAmin 0.85 · typ 1 · max 1.15 MHz5
EN Input Logic High VIHIOUT = 1 mAmin 75 % of VIN5
EN Input Logic Low VILIOUT = 1 mAmax 20 % of VIN5
EN Input Leakage Current IENLKVEN = 1.2Vtyp 0.1 uA5
Power Good Threshold PGTHFVFB Falling, Note 5typ 90 %5
Power Good Hysteresis PGHYSNote 5typ 3 %5
Power Good Output Low PGLOWISINK = 5 mA, VFB = 0V, Note 5typ 0.4 V5
Power Good Output Delay PGDELAYNote 5typ 600 us5
Power Good Output Response PGRESNote 5typ 250 us5
Power Good Input Voltage Operating Range VPG_VINISINK = 5 mA, VFB = 0V, Note 5min 0.9 · max 5.5 V5
Power Good Leakage Current PGLEAKVPG = 5.5V, VOUT in Regulation, Note 5typ 0.01 uA5
Soft Start Time tSSEN Low to High, 90% of VOUT, Note 4: 220 resistive load, 3.3V VOUT (15 mA); Note 5typ 550 us5
Thermal Shutdown Die Temperature TSDNote 5typ 150 C5
Die Temperature Hysteresis TSDHYSNote 5typ 35 C5
Operating Ambient Temperature Range TASteady Statemin -40 · max 85 °C5
Storage Temperature Range TAmin -65 · max 150 °C5
Maximum Junction Temperature TJTransientmax 150 °C5
Thermal Resistance, 8L-MSOP JA8L-MSOPtyp 211 °C/W5

Pins, by the datasheet

8
1 EN
Logic high enables operation; do not allow this pin to float. · p. 11
2 NC
Not connected. · p. 11
3 PG
Power Good output indicates when the output voltage is within regulation. · p. 11
4 VOUT
Boost converter output; connects to the output capacitor. · p. 11
5 SW
Boost and rectifier switch node; connect the boost inductor between SW and VIN. · p. 11
6 PGND
Power ground reference; connect externally to SGND. · p. 11
7 SGND
Signal ground reference; connect externally to PGND. · p. 11
8 VIN
Input supply voltage; local bypass capacitor required. · p. 11

Open-source boards using it

2
  • 4 layers106 × 29.2 mmBatterymeter, the printed circuit board in 3D

    Batterymeter

    hb020/batterymeter

    Handheld Battery AC and Time Domain characterization tool on Attiny series 2

    145 parts20
  • 4 layers106 × 29.2 mmBatterymeter, the printed circuit board in 3D

    Batterymeter

    hb020/batterymeter

    Handheld Battery AC and Time Domain characterization tool on Attiny series 2

    129 parts20

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the MCP1642B-33I/MS?

Yes. The symbol is EasyEDA_Cloud:MCP1642BT-18I_MS and the footprint Package_SO:MSOP-8_3x3mm_P0.65mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the MCP1642B-33I/MS?

MSOP-8, with 8 pins. Its footprint is drawn on this page.

Where is the MCP1642B-33I/MS datasheet?

Microchip Technology publishes it: the Datasheet link on this page opens it.

Where can I order the MCP1642B-33I/MS?

JLCPCB lists it as part C635907, with 31 in stock; the sellers' links on this page open their listings.

What can replace the MCP1642B-33I/MS?

Parts like it in the library: the MCP1642D-33I/MS by Microchip Technology, the LTC1475CMS8-3.3#PBF by Analog Devices, the LT1767EMS8#TRPBF by Analog Devices and the LT1767EMS8-3.3#PBF by Analog Devices. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the MCP1642B-33I/MS?

2 boards in 1 repository on GitHub; the most starred are listed on this page, with their KiCad files.