Skip to the content
21

ATTINY44A-MU

Microchip TechnologyExtended

-40℃~+85℃ 1.8V~5.5V 10bit 12 20MHz 256Byte 256Byte 4KB 8 Bit AVR Built-in FLASH Power-on reset (POR)、Undervoltage detection (BOR/LVD/LVR/LVI)、Watchdog reset、External pin reset (NRST)、Built-in general-purpose timer、Programmable watchdog、Built-in temperature sensor QFN-20-EP(4x4) Microcontrollers (MCU/MPU/SOC) ROHS

Part id
microchip/ATTINY44A-MU
Category
Microcontrollers (MCU, MPU, SOC)
Package
QFN-20-EP(4x4)
Pins
21
In stock
108 at JLCPCB (C123718)
Used on
8 open-source boards

Overview

The ATTINY44A-MU is a microcontroller made by Microchip Technology in a QFN-20-EP(4x4) package with 21 pins. -40℃~+85℃ 1.8V~5.5V 10bit 12 20MHz 256Byte 256Byte 4KB 8 Bit AVR Built-in FLASH Power-on reset (POR)、Undervoltage detection (BOR/LVD/LVR/LVI)、Watchdog reset、External pin reset (NRST)、Built-in general-purpose timer、Programmable watchdog、Built-in temperature sensor QFN-20-EP(4x4) Microcontrollers (MCU/MPU/SOC) ROHS.

PCBKit's library has its KiCad symbol (MCU_Microchip_ATtiny:ATtiny44A-M, from KiCad's library) and its footprint (Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.6x2.6mm, from KiCad's library), ready for a KiCad board. 108 are in stock at JLCPCB (part C123718). 8 open-source boards in 5 repositories on GitHub use it.

Symbol

1PA42PA33PA24PA15AREF/PA08GND9VCC11XTAL1/PB012XTAL2/PB113RESET/PB314PB215PA716PA620PA5
MCU_Microchip_ATtiny:ATtiny44A-MFrom KiCad's library

Footprint

21
Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.6x2.6mmFrom KiCad's library

From the datasheet

9
Supply, least
1.8 V · VCC, recommended operating min · p. 1
Supply, most
5.5 V · VCC, recommended operating max · p. 1
Supply, absolute maximum
6 V · VCC, absolute max · p. 173
Works from
-40 °C · Industrial operating temperature min · p. 1
Works up to
85 °C · Industrial operating temperature max · p. 1
A pin gives at most
40 mA · DC current per I/O pin, absolute max · p. 173
Takes working
4.4 mA · VCC, active mode typical at 8 MHz, 5 V, external clock, PRR = 0xFF, no I/O drive · p. 174
Takes at most
7 mA · VCC, active mode max at 8 MHz, 5 V, external clock, PRR = 0xFF, no I/O drive · p. 174
Takes asleep
130 nA · VCC, power-down typical at 3 V, WDT disabled, BOD disabled · p. 174

What it is and has

38
Core
AVR 8-bit · p. 1
Instruction set
120 instructions, most single clock cycle · p. 1
Working registers
32 x 8 · p. 1
Flash memory
4K Bytes, in-system self-programmable · p. 1
EEPROM
256 Bytes · p. 1
SRAM
256 Bytes · p. 1
Timers
One 8-bit and one 16-bit, two PWM channels each · p. 1
ADC resolution
10-bit · p. 132
ADC single-ended channels
8 · p. 132
ADC differential channels
12, selectable gain 1x or 20x · p. 132
ADC absolute accuracy
±2 LSB · p. 132
ADC maximum sample rate
15 kSPS at maximum resolution · p. 132
Watchdog
Programmable, separate on-chip oscillator · p. 1
Analog comparator
On-chip · p. 1
Serial interface
Universal Serial Interface · p. 1
Debug interface
debugWIRE · p. 1
Programming
In-system via SPI · p. 1
GPIO
12 programmable lines · p. 1
Pin change interrupts
12 pins · p. 1
Power saving modes
Idle, ADC Noise Reduction, Standby, Power-down · p. 1
Brown-out detection
Programmable, software disable · p. 1
Oscillator
Internal calibrated oscillator · p. 1
Temperature sensor
On-chip · p. 1
Package options
20-pin QFN/MLF/VQFN, 14-pin SOIC, 14-pin PDIP, 15-ball UFBGA · p. 1
Clock speed
0–4 MHz at 1.8–5.5 V · p. 1
Clock speed
0–10 MHz at 2.7–5.5 V · p. 1
Clock speed
0–20 MHz at 4.5–5.5 V · p. 1
Core
AVR 8-bit microcontroller · p. 1
Architecture
Advanced RISC · p. 1
Instruction set
120 instructions, most execute in one clock cycle · p. 1
Operation
Fully static · p. 1
Flash endurance
10,000 write/erase cycles · p. 1
EEPROM endurance
100,000 write/erase cycles · p. 1
Data retention
20 years at 85°C / 100 years at 25°C · p. 1
Memory security
Programming lock for self-programming Flash and EEPROM · p. 1
Timer/Counter
One 8-bit and one 16-bit, each with two PWM channels · p. 1
ADC differential channels
12 channel pairs, programmable gain 1x / 20x · p. 1
Watchdog timer
Programmable, separate on-chip oscillator · p. 1

Specifications

82
ParameterConditionsAs printedPage
Operating Temperaturemin -55 · max 125 °C173
Storage Temperaturemin -65 · max 150 °C173
Voltage on any Pin except RESET with respect to Groundmin -0.5 V173
Voltage on RESET with respect to Groundmin -0.5 · max 13 V173
Maximum Operating Voltagemax 6 V173
DC Current per I/O Pinmax 40 mA173
DC Current VCC and GND Pinsmax 200 mA173
Input Low Voltage VILTA = -40°C to +85°C; VCC = 1.8V - 2.4Vmin -0.5 V173
Input Low Voltage VILTA = -40°C to +85°C; VCC = 2.4V - 5.5Vmin -0.5 V173
Input Low Voltage, RESET Pin as Reset VILTA = -40°C to +85°C; VCC = 1.8V - 5.5; not tested in productionmin -0.5 V173
Output Low Voltage Except RESET pin VOLTA = -40°C to +85°C; IOL = 10 mA, VCC = 5Vmax 0.6 V173
Output Low Voltage Except RESET pin VOLTA = -40°C to +85°C; IOL = 5 mA, VCC = 3Vmax 0.5 V173
Output High-voltage Except RESET pin VOHTA = -40°C to +85°C; IOH = -10 mA, VCC = 5Vmin 4.3 V173
Output High-voltage Except RESET pin VOHTA = -40°C to +85°C; IOH = -5 mA, VCC = 3Vmin 2.5 V173
Input Leakage Current I/O Pin ILILTA = -40°C to +85°C; VCC = 5.5V, pin low (absolute value); typical at 25°Cmax 1 uA173
Input Leakage Current I/O Pin ILIHTA = -40°C to +85°C; VCC = 5.5V, pin high (absolute value); typical at 25°Cmax 1 uA173
Pull-up Resistor, I/O Pin RPUTA = -40°C to +85°C; VCC = 5.5V, input lowmin 20 · max 50 kΩ173
Pull-up Resistor, Reset Pin RPUTA = -40°C to +85°C; VCC = 5.5V, input lowmin 30 · max 60 kΩ173
Supply Current, Active Mode ICCTA = -40°C to +85°C; f = 1 MHz, VCC = 2V; external clock, PRR = 0xFF, no I/O drive; typical at 25°Ctyp 0.25 · max 0.5 mA174
Supply Current, Active Mode ICCTA = -40°C to +85°C; f = 4 MHz, VCC = 3V; external clock, PRR = 0xFF, no I/O drive; typical at 25°Ctyp 1.2 · max 2 mA174
Supply Current, Active Mode ICCTA = -40°C to +85°C; f = 8 MHz, VCC = 5V; external clock, PRR = 0xFF, no I/O drive; typical at 25°Ctyp 4.4 · max 7 mA174
Supply Current, Idle Mode ICCTA = -40°C to +85°C; f = 1 MHz, VCC = 2V; external clock, PRR = 0xFF, no I/O drive; typical at 25°Ctyp 0.04 · max 0.2 mA174
Supply Current, Idle Mode ICCTA = -40°C to +85°C; f = 4 MHz, VCC = 3V; external clock, PRR = 0xFF, no I/O drive; typical at 25°Ctyp 0.25 · max 0.6 mA174
Supply Current, Idle Mode ICCTA = -40°C to +85°C; f = 8 MHz, VCC = 5V; external clock, PRR = 0xFF, no I/O drive; typical at 25°Ctyp 1.3 · max 2 mA174
Supply Current, Power-Down Mode ICCTA = -40°C to +85°C; WDT enabled, VCC = 3V; BOD disabled; typical at 25°Ctyp 4 · max 10 uA174
Supply Current, Power-Down Mode ICCTA = -40°C to +85°C; WDT disabled, VCC = 3V; BOD disabled; typical at 25°Ctyp 0.13 · max 2 uA174
Clock Frequency 1/tCLCLVCC = 1.8 - 5.5Vmin 0 · max 4 MHz175
Clock Frequency 1/tCLCLVCC = 2.7 - 5.5Vmin 0 · max 10 MHz175
Clock Frequency 1/tCLCLVCC = 4.5 - 5.5Vmin 0 · max 20 MHz175
Clock Period tCLCLVCC = 1.8 - 5.5Vmin 250 ns175
Clock Period tCLCLVCC = 2.7 - 5.5Vmin 100 ns175
Clock Period tCLCLVCC = 4.5 - 5.5Vmin 50 ns175
High Time tCHCXVCC = 1.8 - 5.5Vmin 100 ns175
High Time tCHCXVCC = 2.7 - 5.5Vmin 40 ns175
High Time tCHCXVCC = 4.5 - 5.5Vmin 20 ns175
Low Time tCLCXVCC = 1.8 - 5.5Vmin 100 ns175
Low Time tCLCXVCC = 2.7 - 5.5Vmin 40 ns175
Low Time tCLCXVCC = 4.5 - 5.5Vmin 20 ns175
Rise Time tCLCHVCC = 1.8 - 5.5Vmax 2 us175
Rise Time tCLCHVCC = 2.7 - 5.5Vmax 1.6 us175
Rise Time tCLCHVCC = 4.5 - 5.5Vmax 0.5 us175
Fall Time tCHCLVCC = 1.8 - 5.5Vmax 2 us175
Fall Time tCHCLVCC = 2.7 - 5.5Vmax 1.6 us175
Fall Time tCHCLVCC = 4.5 - 5.5Vmax 0.5 us175
Change in period from one clock cycle to the next ΔtCLCLVCC = 1.8 - 5.5Vmax 2 %175
Change in period from one clock cycle to the next ΔtCLCLVCC = 2.7 - 5.5Vmax 2 %175
Change in period from one clock cycle to the next ΔtCLCLVCC = 4.5 - 5.5Vmax 2 %175
RESET pin threshold voltage VRSTLimits are 0.2 VCC and 0.9VCC; values are guidelines onlymin 0.2 · max 0.9 VCC176
Minimum pulse width on RESET pin tRSTVCC = 1.8V; values are guidelines onlytyp 2000 ns176
Minimum pulse width on RESET pin tRSTVCC = 3V; values are guidelines onlytyp 700 ns176
Minimum pulse width on RESET pin tRSTVCC = 5V; values are guidelines onlytyp 400 ns176
Brown-out Detector hysteresis VHYSTValues are guidelines onlytyp 50 mV176
Minimum pulse width on Brown-out Reset tBODValues are guidelines onlytyp 2 us176
Internal bandgap reference voltage VBGVCC = 5V, TA = 25°C; values are guidelines onlymin 1 · typ 1.1 · max 1.2 V176
Internal bandgap reference start-up time tBGVCC = 5V, TA = 25°C; values are guidelines onlytyp 40 · max 70 us176
Internal bandgap reference current consumption IBGVCC = 5V, TA = 25°C; values are guidelines onlytyp 15 uA176
Release threshold of power-on reset VPORVoltage rising; values are guidelines onlymin 1.1 · typ 1.4 · max 1.6 V176
Activation threshold of power-on reset VPOAValues are guidelines onlymin 0.6 · typ 1.3 · max 1.6 V176
Power-On Slope Rate SRONValues are guidelines onlymin 0.01 V/ms176
VBOT VBOTBODLEVEL[2:0] Fuses = 110min 1.7 · typ 1.8 · max 2 V176
VBOT VBOTBODLEVEL[2:0] Fuses = 101min 2.5 · typ 2.7 · max 2.9 V176
VBOT VBOTBODLEVEL[2:0] Fuses = 100min 4.1 · typ 4.3 · max 4.5 V176
PRTIM1VCC = 2V, f = 1 MHztyp 1.6 uA182
PRTIM1VCC = 3V, f = 4 MHztyp 11 uA182
PRTIM1VCC = 5V, f = 8 MHztyp 48 uA182
PRTIM0VCC = 2V, f = 1 MHztyp 4.4 uA182
PRTIM0VCC = 3V, f = 4 MHztyp 29 uA182
PRTIM0VCC = 5V, f = 8 MHztyp 120 uA182
PRUSIVCC = 2V, f = 1 MHztyp 1.6 uA182
PRUSIVCC = 3V, f = 4 MHztyp 11 uA182
PRUSIVCC = 5V, f = 8 MHztyp 48 uA182
PRADCVCC = 2V, f = 1 MHztyp 8 uA182
PRADCVCC = 3V, f = 4 MHztyp 55 uA182
PRADCVCC = 5V, f = 8 MHztyp 240 uA182
PRTIM1Current consumption additional to active mode with external clocktyp 1 %183
PRTIM1Current consumption additional to idle mode with external clocktyp 5 %183
PRTIM0Current consumption additional to active mode with external clocktyp 3 %183
PRTIM0Current consumption additional to idle mode with external clocktyp 10 %183
PRUSICurrent consumption additional to active mode with external clocktyp 1 %183
PRUSICurrent consumption additional to idle mode with external clocktyp 5 %183
PRADCCurrent consumption additional to active mode with external clocktyp 5 %183
PRADCCurrent consumption additional to idle mode with external clocktyp 20 %183

Open-source boards using it

8
  • 4 layers45 × 70 mmSZG TEMPLATE STD, the printed circuit board in 3D

    SZG TEMPLATE STD

    SYZYGYfpga/pcb-templates

    Template PCB's for SYZYGY board designs

    31 parts31
  • 2 layers40 × 40 mmFancyLight V2, the printed circuit board in 3D

    FancyLight V2

    Glebka/FancyLight

    FancyLight - an LED lamp powered by a Li-Ion battery, which can be found in used electronic cigarettes. It charges via a micro USB connector and is turned on and off using a touch button.

    52 parts1
  • 6 layers50 × 35 mmSyzygy usb3, the printed circuit board in 3D

    Syzygy usb3

    miek/test-pcbs

    35 parts1
  • 2 layersElectronic Dropper, the printed circuit board in 3D

    Electronic Dropper

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    15 parts915
  • 2 layers25 × 26.2 mmElectronic Dropper, the printed circuit board in 3D

    Electronic Dropper

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    12 parts915
  • 4 layers50 × 70 mmSZG TEMPLATE TXR, the printed circuit board in 3D

    SZG TEMPLATE TXR

    SYZYGYfpga/pcb-templates

    Template PCB's for SYZYGY board designs

    31 parts31
  • 2 layers98.8 × 68 mmJulkort, the printed circuit board in 3D

    Julkort

    CASE-Association/christmas-cards

    All CASE christmas cards over the years

    30 parts3GPL-3.0
  • 2 layers6.6 × 0.8 mmJulkort Blank, the printed circuit board in 3D

    Julkort Blank

    CASE-Association/christmas-cards

    All CASE christmas cards over the years

    26 parts3GPL-3.0

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the ATTINY44A-MU?

Yes. The symbol is MCU_Microchip_ATtiny:ATtiny44A-M and the footprint Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.6x2.6mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the ATTINY44A-MU?

QFN-20-EP(4x4), with 21 pins. Its footprint is drawn on this page.

Where is the ATTINY44A-MU datasheet?

Microchip Technology publishes it: the Datasheet link on this page opens it.

Where can I order the ATTINY44A-MU?

JLCPCB lists it as part C123718, with 108 in stock; the sellers' links on this page open their listings.

What can replace the ATTINY44A-MU?

Parts like it in the library: the ATTINY84A-MU by Microchip Technology, the ATTINY24A-MF by Microchip Technology, the ATTINY25-20MU by Microchip Technology and the ATTINY84-20MU by Microchip Technology. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the ATTINY44A-MU?

8 boards in 5 repositories on GitHub; the most starred are listed on this page, with their KiCad files.