Skip to the content
12345678

93LC56BT-I/SN

Microchip TechnologyExtended

-40℃~+85℃ 1,000,000 cycles 2.5V~5.5V 200 Years 2Kbit 2ms 3MHz Built-in write enable latch (WEL)、Power-down/Power-up protection circuit SPI SOIC-8 EEPROM ROHS

Part id
microchip/93LC56BT-I/SN
Category
EEPROM
Package
SOIC-8
Pins
8
In stock
2,227 at JLCPCB (C6164)
Used on
4 open-source boards

Overview

The 93LC56BT-I/SN is an EEPROM made by Microchip Technology in a SOIC-8 package with 8 pins. -40℃~+85℃ 1,000,000 cycles 2.5V~5.5V 200 Years 2Kbit 2ms 3MHz Built-in write enable latch (WEL)、Power-down/Power-up protection circuit SPI SOIC-8 EEPROM ROHS.

PCBKit's library has its KiCad symbol (Memory_EEPROM:93LCxxB, from KiCad's library) and its footprint (Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, from KiCad's library), ready for a KiCad board. 2,227 are in stock at JLCPCB (part C6164). 4 open-source boards in 2 repositories on GitHub use it.

Symbol

1CS2SCLK3DI4DO5GND8VCC
Memory_EEPROM:93LCxxBFrom KiCad's library

Footprint

12345678
Package_SO:SOIC-8_3.9x4.9mm_P1.27mmFrom KiCad's library

From the datasheet

8
Supply, least
2.5 V · VCC, recommended operating min · p. 1
Supply, most
5.5 V · VCC, recommended operating max · p. 1
Supply, absolute maximum
7 V · VCC, absolute max · p. 3
Works from
-40 °C · Industrial (I) operating ambient min · p. 1
Works up to
85 °C · Industrial (I) operating ambient max · p. 1
Takes working
100 µA · VCC read current typical, FCLK = 2 MHz, VCC = 2.5 V · p. 3
Takes at most
2 mA · VCC write current max, FCLK = 3 MHz, VCC = 5.5 V · p. 3
Takes asleep
1 µA · VCC standby current max, Industrial temperature · p. 3

What it is and has

9
Memory
2K Microwire compatible serial EEPROM · p. 1
Memory organization
128 x 16-bit, no ORG pin · p. 1
Interface
3-Wire Serial I/O · p. 1
Protection
Power-On/Off Data Protection Circuitry · p. 1
Device status
Ready/Busy signal · p. 1
Read function
Sequential read · p. 1
Endurance
1,000,000 Erase/write Cycles · p. 1
Data retention
> 200 Years · p. 1
Compliance
Pb-free and RoHS Compliant · p. 1

Specifications

36
ParameterConditionsAs printedPage
VCC VCCmax 7 V3
All inputs and outputs w.r.t. VSSmin -0.6 V3
Storage temperaturemin -65 · max 150 °C3
Ambient temperature with power appliedmin -40 · max 125 °C3
High-level input voltage VIH1VCC ≥ 2.7Vmin 2 V3
Low-level input voltage VIL1VCC ≥ 2.7Vmin -0.3 · max 0.8 V3
Low-level input voltage VIL2VCC < 2.7Vmin -0.3 V3
Low-level output voltage Vol1IOL = 2.1 mA, VCC = 4.5Vmax 0.4 V3
Low-level output voltage Vol2IOL = 100 uA, VCC = 2.5Vmax 0.2 V3
High-level output voltage VOH1IOH = -400 uA, VCC = 4.5Vmin 2.4 V3
Pin capacitance (all inputs/outputs) CIN, COUTVIN/VOUT = 0V; TA = 25°C, FCLK = 1 MHz; Note 1max 7 pF3
Write current ICC writeFCLK = 3 MHz, Vcc = 5.5Vmax 2 mA3
Write current ICC writeFCLK = 2 MHz, Vcc = 2.5Vtyp 500 A3
Read current ICC readFCLK = 3 MHz, VCC = 5.5Vmax 1 mA3
Read current ICC readFCLK = 2 MHz, VCC = 3.0Vmax 500 A3
Read current ICC readFCLK = 2 MHz, VCC = 2.5Vtyp 100 A3
Standby current ICCSI – Temp; CLK = CS = 0V; DI = VSS or VCC; Ready/Busy status cleared from DOmax 1 A3
VCC voltage detect VPOR93LC56B; Note 1typ 1.5 V3
Clock frequency FCLK2.5V ≤ VCC < 5.5Vmax 2 MHz4
Clock high time TCKH2.5V ≤ VCC < 5.5Vmin 250 ns4
Clock low time TCKL2.5V ≤ VCC < 5.5Vmin 200 ns4
Chip Select setup time TCSS4.5V ≤ VCC < 5.5Vmin 50 ns4
Chip Select setup time TCSS2.5V ≤ VCC < 4.5Vmin 100 ns4
Chip Select hold time TCSH1.8V ≤ VCC < 5.5Vmin 0 ns4
Chip Select low time TCSL1.8V ≤ VCC < 5.5Vmin 250 ns4
Data input setup time TDIS2.5V ≤ VCC < 5.5Vmin 100 ns4
Data input hold time TDIH2.5V ≤ VCC < 5.5Vmin 100 ns4
Data output delay time TPD4.5V ≤ VCC < 5.5V, CL = 100 pFmax 200 ns4
Data output delay time TPD2.5V ≤ VCC < 4.5V, CL = 100 pFmax 250 ns4
Data output disable time TCZ4.5V ≤ VCC < 5.5V; Note 1max 100 ns4
Data output disable time TCZ1.8V ≤ VCC < 4.5V; Note 1max 200 ns4
Status valid time TSV4.5V ≤ VCC < 5.5V, CL = 100 pFmax 200 ns4
Status valid time TSV2.5V ≤ VCC < 4.5V, CL = 100 pFmax 300 ns4
Program cycle time TWCErase/Write mode, LC versionsmax 6 ms4
Program cycle time TECERAL mode, 4.5V ≤ VCC ≤ 5.5Vmax 6 ms4
Program cycle time TWLWRAL mode, 4.5V ≤ VCC ≤ 5.5Vmax 15 ms4

Pins, by the datasheet

8
1 CS
Chip Select; high selects the device and low deselects it into Standby mode. · p. 12
2 CLK
Serial Clock; instructions and data are clocked on its positive edge. · p. 12
3 DI
Data In for the Start bit, opcode, address and data. · p. 12
4 DO
Data Out during reads; also provides Ready/Busy status during erase and write cycles. · p. 12
5 VSS
Ground. · p. 12
6 ORG/NC
No internal connection on 93XX56A/B devices. · p. 12
7 NC
No Internal Connection. · p. 12
8 VCC
Power Supply. · p. 12

Open-source boards using it

4
  • 4 layers130 × 90 mmDual adc usb, the printed circuit board in 3D

    Dual adc usb

    devbisme/ai-circuit-design-tests

    Tests of KiCad-related AI tools.

    197 parts10
  • 4 layers150 × 90 mmDual adc usb, the printed circuit board in 3D

    Dual adc usb

    devbisme/ai-circuit-design-tests

    Tests of KiCad-related AI tools.

    186 parts10
  • 4 layers125 × 95 mmPrerouted, the printed circuit board in 3D

    Prerouted

    devbisme/ai-circuit-design-tests

    Tests of KiCad-related AI tools.

    179 parts10
  • 2 layers100 × 100 mmOpen65, the printed circuit board in 3D

    Open65

    Maverick-Shark/X65_BigMiST

    The X65 is an ultimate computer for everyone interested in the venerable 65-series of 8-bit and 16-bit CPUs, i.e. the 6502 and 65816.

    195 partsMIT

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the 93LC56BT-I/SN?

Yes. The symbol is Memory_EEPROM:93LCxxB and the footprint Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the 93LC56BT-I/SN?

SOIC-8, with 8 pins. Its footprint is drawn on this page.

Where is the 93LC56BT-I/SN datasheet?

Microchip Technology publishes it: the Datasheet link on this page opens it.

Where can I order the 93LC56BT-I/SN?

JLCPCB lists it as part C6164, with 2,227 in stock; the sellers' links on this page open their listings.

What can replace the 93LC56BT-I/SN?

Parts like it in the library: the 93AA66A-I/SN by Microchip Technology, the 93LC86CT-I/SN by Microchip Technology, the CAT93C86VI-GT3 by onsemi and the 93AA66C-I/SN by Microchip Technology. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the 93LC56BT-I/SN?

4 boards in 2 repositories on GitHub; the most starred are listed on this page, with their KiCad files.