
LCMXO2-1200HC-4SG32I
LatticeExtended
-40℃~+100℃ 1280 160 2.375V~3.465V 21 65536bit MachXO2 Supports hot swap、Supports watchdog timeout detection QFN-32-EP(5x5) Programmable Logic Device (CPLDs/FPGAs) ROHS
- Part id
- lattice/LCMXO2-1200HC-4SG32I
- Category
- Programmable Logic Device (CPLDs, FPGAs)
- Package
- QFN-32-EP(5x5)
- Pins
- 33
- In stock
- 54 at JLCPCB (C1551142)
- Used on
- 3 open-source boards
Overview
The LCMXO2-1200HC-4SG32I is a programmable Logic Device made by Lattice in a QFN-32-EP(5x5) package with 33 pins. -40℃~+100℃ 1280 160 2.375V~3.465V 21 65536bit MachXO2 Supports hot swap、Supports watchdog timeout detection QFN-32-EP(5x5) Programmable Logic Device (CPLDs/FPGAs) ROHS.
PCBKit's library has its KiCad symbol (EasyEDA_Cloud:LCMXO2-1200ZE-2SG32I, from EasyEDA) and its footprint (EasyEDA_Cloud:QFN-32_L5.0-W5.0-P0.50-TL-EP3.5, from EasyEDA), ready for a KiCad board. 54 are in stock at JLCPCB (part C1551142). 3 open-source boards in 3 repositories on GitHub use it.
Symbol
Footprint
From the datasheet
6- Supply, least
- 2.375 V · VCC, recommended operating min, HC devices · p. 42
- Supply, most
- 3.6 V · VCC, recommended operating max, HC devices · p. 42
- Supply, least
- 1.14 V · VCCIO, recommended operating min · p. 42
- Supply, absolute maximum
- 3.75 V · VCC, absolute max, HC devices · p. 42
- Junction, hottest
- 125 °C · Junction temperature, absolute max · p. 42
- Takes asleep
- 3.49 mA · VCC static supply current typical, blank pattern, 0 MHz, TJ = 25 °C · p. 46
Around it
10- res 158 Ohms
- between LVCMOS output + and LVDS25E line +; Driver series resistor in the LVDS25E example; one on each complementary output, ±1%. · p. 51
- res 140 Ohms
- between LVDS25E line + and LVDS25E line -; Driver parallel resistor in the LVDS25E example; ±1%. · p. 51
- res 100 Ohms
- between LVDS25E receiver + and LVDS25E receiver -; Receiver termination in the LVDS25E example; ±1%. · p. 51
- res 80 Ohms
- between LVCMOS output + and BLVDS line +; Driver series resistor in the BLVDS multipoint example. · p. 52
- res 45 Ohms
- between BLVDS line + and BLVDS line -; Left end termination for Zo = 45 Ohms. · p. 52
- res 90 Ohms
- between BLVDS line + and BLVDS line -; Left end termination for Zo = 90 Ohms. · p. 52
- res 45 Ohms
- between BLVDS line + and BLVDS line -; Right end termination for Zo = 45 Ohms. · p. 52
- res 90 Ohms
- between BLVDS line + and BLVDS line -; Right end termination for Zo = 90 Ohms. · p. 52
- res 93 Ohms
- between LVCMOS output + and LVPECL line +; Driver series resistor in the differential LVPECL example. · p. 53
- res 196 Ohms
- between LVPECL line + and LVPECL line -; Driver parallel resistor in the differential LVPECL example. · p. 53
Specifications
313| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Supply Voltage VCC VCC | MachXO2 HC (2.5 V / 3.3 V) | min -0.5 · max 3.75 V | 42 |
| Output Supply Voltage VCCIO VCCIO | MachXO2 HC (2.5 V / 3.3 V) | min -0.5 · max 3.75 V | 42 |
| I/O Tri-state Voltage Applied | MachXO2 HC (2.5 V / 3.3 V); dual function I2C pins have separate limits | min -0.5 · max 3.75 V | 42 |
| Dedicated Input Voltage Applied | MachXO2 HC (2.5 V / 3.3 V) | min -0.5 · max 3.75 V | 42 |
| Storage Temperature (Ambient) | MachXO2 HC (2.5 V / 3.3 V) | min -55 · max 125 °C | 42 |
| Junction Temperature (TJ) TJ | MachXO2 HC (2.5 V / 3.3 V) | min -40 · max 125 °C | 42 |
| Core Supply Voltage for 2.5 V / 3.3 V Devices VCC | HC devices | min 2.375 · max 3.6 V | 42 |
| I/O Driver Supply Voltage VCCIO | min 1.14 · max 3.6 V | 42 | |
| Junction Temperature Industrial Operation tJIND | Industrial grade | min -40 · max 100 °C | 42 |
| Power supply ramp rates for all power supplies. tRAMP | Assumes monotonic ramp rates | min 0.01 · max 100 V/ms | 42 |
| Power-On-Reset ramp up trip point (band gap based circuit monitoring VCCINT and VCCIO0) VPORUP | min 0.9 · max 1.06 V | 43 | |
| Power-On-Reset ramp up trip point (band gap based circuit monitoring external VCC power supply) VPORUPEXT | HC devices only | min 1.5 · max 2.1 V | 43 |
| Power-On-Reset ramp down trip point (band gap based circuit monitoring VCCINT) VPORDNBG | min 0.75 · max 0.93 V | 43 | |
| Power-On-Reset ramp down trip point (band gap based circuit monitoring VCC) VPORDNBGEXT | min 0.98 · max 1.33 V | 43 | |
| Power-On-Reset ramp down trip point (SRAM based circuit monitoring VCCINT) VPORDNSRAM | typ 0.6 V | 43 | |
| Power-On-Reset ramp down trip point (SRAM based circuit monitoring VCC) VPORDNSRAMEXT | typ 0.96 V | 43 | |
| Flash Programming cycles per tRETENTION NPROGCYC | max 10000 Cycles | 43 | |
| Flash functional programming cycles NPROGCYC | max 100000 Cycles | 43 | |
| Data retention at 100 °C junction temperature tRETENTION | 100 °C junction temperature | min 10 Years | 43 |
| Data retention at 85 °C junction temperature tRETENTION | 85 °C junction temperature | min 20 Years | 43 |
| Input or I/O leakage Current IDK | 0 < VIN < VIH (MAX); maximum magnitude ±1000 uA | max 1000 uA | 43 |
| Input or I/O Leakage IIL, IIH | Clamp OFF and VCCIO < VIN < VIH (MAX) | max 175 uA | 44 |
| Input or I/O Leakage IIL, IIH | Clamp OFF and VIN = VCCIO | min -10 · max 10 uA | 44 |
| Input or I/O Leakage IIL, IIH | Clamp OFF and VCCIO –0.97 V < VIN < VCCIO | min -175 uA | 44 |
| Input or I/O Leakage IIL, IIH | Clamp OFF and 0 V < VIN < VCCIO –0.97 V | max 10 uA | 44 |
| Input or I/O Leakage IIL, IIH | Clamp OFF and VIN = GND | max 10 uA | 44 |
| Input or I/O Leakage IIL, IIH | Clamp ON and 0 V < VIN < VCCIO | max 10 uA | 44 |
| I/O Active Pull-up Current IPU | 0 < VIN < 0.7 VCCIO | min -30 · max -309 uA | 44 |
| I/O Active Pull-down Current IPD | VIL (MAX) < VIN < VCCIO | min 30 · max 305 uA | 44 |
| Bus Hold Low sustaining current IBHLS | VIN = VIL (MAX) | min 30 uA | 44 |
| Bus Hold High sustaining current IBHHS | VIN = 0.7VCCIO | min -30 uA | 44 |
| Bus Hold Low Overdrive current IBHLO | 0 ≤ VIN ≤ VCCIO | max 305 uA | 44 |
| Bus Hold High Overdrive current IBHHO | 0 ≤ VIN ≤ VCCIO | max -309 uA | 44 |
| I/O Capacitance C1 | VCCIO = 3.3 V, 2.5 V, 1.8 V, 1.5 V, 1.2 V; VCC = Typ., VIO = 0 to VIH (MAX); TA 25 °C, f = 1.0 MHz | min 3 · typ 5 · max 9 pF | 44 |
| Dedicated Input Capacitance C2 | VCCIO = 3.3 V, 2.5 V, 1.8 V, 1.5 V, 1.2 V; VCC = Typ., VIO = 0 to VIH (MAX); TA 25 °C, f = 1.0 MHz | min 3 · typ 5.5 · max 7 pF | 44 |
| Hysteresis for Schmitt Trigger Inputs VHYST | VCCIO = 3.3 V, Hysteresis = Large; bus keeper circuit turned on | typ 450 mV | 44 |
| Hysteresis for Schmitt Trigger Inputs VHYST | VCCIO = 2.5 V, Hysteresis = Large; bus keeper circuit turned on | typ 250 mV | 44 |
| Hysteresis for Schmitt Trigger Inputs VHYST | VCCIO = 1.8 V, Hysteresis = Large; bus keeper circuit turned on | typ 125 mV | 44 |
| Hysteresis for Schmitt Trigger Inputs VHYST | VCCIO = 1.5 V, Hysteresis = Large; bus keeper circuit turned on | typ 100 mV | 44 |
| Hysteresis for Schmitt Trigger Inputs VHYST | VCCIO = 2.5 V, Hysteresis = Small; bus keeper circuit turned on | typ 150 mV | 44 |
| Hysteresis for Schmitt Trigger Inputs VHYST | VCCIO = 1.8 V, Hysteresis = Small; bus keeper circuit turned on | typ 60 mV | 44 |
| Hysteresis for Schmitt Trigger Inputs VHYST | VCCIO = 1.5 V, Hysteresis = Small; bus keeper circuit turned on | typ 40 mV | 44 |
| Core Power Supply ICC | LCMXO2-1200HC; blank pattern, outputs tri-stated, LVCMOS inputs held at VCCIO or GND, oscillator and PLL off; frequency = 0 MHz; TJ = 25 °C, nominal supply voltages | typ 3.49 mA | 46 |
| Bank Power Supply VCCIO = 2.5 V ICCIO | All devices; blank pattern, frequency = 0 MHz; TJ = 25 °C, nominal supply voltages; excludes pull-up/pull-down | typ 0 mA | 46 |
| Core Power Supply ICC | LCMXO2-1200HC; inputs held at VCCIO or GND, outputs tri-stated; typical user pattern; JTAG programming at 25 MHz; TJ = 25 °C, nominal supply voltages | typ 18.8 mA | 46 |
| Bank Power Supply ICCIO | All devices; per bank, VCCIO = 2.5 V; excludes pull-up/pull-down; inputs held at VCCIO or GND, outputs tri-stated; TJ = 25 °C | typ 0 mA | 46 |
| VCCIO VCCIO | LVCMOS 3.3 | min 3.135 · typ 3.3 · max 3.6 V | 48 |
| VCCIO VCCIO | LVCMOS 2.5 | min 2.375 · typ 2.5 · max 2.625 V | 48 |
| VCCIO VCCIO | LVCMOS 1.8 | min 1.71 · typ 1.8 · max 1.89 V | 48 |
| VCCIO VCCIO | LVCMOS 1.5 | min 1.425 · typ 1.5 · max 1.575 V | 48 |
| VCCIO VCCIO | LVCMOS 1.2 | min 1.14 · typ 1.2 · max 1.26 V | 48 |
| VCCIO VCCIO | LVTTL | min 3.135 · typ 3.3 · max 3.6 V | 48 |
| VCCIO VCCIO | PCI; input on bottom bank only | min 3.135 · typ 3.3 · max 3.6 V | 48 |
| VCCIO VCCIO | SSTL25 | min 2.375 · typ 2.5 · max 2.625 V | 48 |
| VREF VREF | SSTL25 | min 1.15 · typ 1.25 · max 1.35 V | 48 |
| VCCIO VCCIO | SSTL18 | min 1.71 · typ 1.8 · max 1.89 V | 48 |
| VREF VREF | SSTL18 | min 0.833 · typ 0.9 · max 0.969 V | 48 |
| VCCIO VCCIO | HSTL18 | min 1.71 · typ 1.8 · max 1.89 V | 48 |
| VREF VREF | HSTL18 | min 0.816 · typ 0.9 · max 1.08 V | 48 |
| VCCIO VCCIO | LVCMOS25R33 | min 3.135 · typ 3.3 · max 3.6 V | 48 |
| VREF VREF | LVCMOS25R33 | min 1.1 · typ 1.25 · max 1.4 V | 48 |
| VCCIO VCCIO | LVCMOS18R33 | min 3.135 · typ 3.3 · max 3.6 V | 48 |
| VREF VREF | LVCMOS18R33 | min 0.75 · typ 0.9 · max 1.05 V | 48 |
| VCCIO VCCIO | LVCMOS18R25 | min 2.375 · typ 2.5 · max 2.625 V | 48 |
| VREF VREF | LVCMOS18R25 | min 0.75 · typ 0.9 · max 1.05 V | 48 |
| VCCIO VCCIO | LVCMOS15R33 | min 3.135 · typ 3.3 · max 3.6 V | 48 |
| VREF VREF | LVCMOS15R33 | min 0.6 · typ 0.75 · max 0.9 V | 48 |
| VCCIO VCCIO | LVCMOS15R25 | min 2.375 · typ 2.5 · max 2.625 V | 48 |
| VREF VREF | LVCMOS15R25 | min 0.6 · typ 0.75 · max 0.9 V | 48 |
| VCCIO VCCIO | LVDS25 | min 2.375 · typ 2.5 · max 2.625 V | 48 |
| VCCIO VCCIO | LVDS33 | min 3.135 · typ 3.3 · max 3.6 V | 48 |
| VCCIO VCCIO | LVPECL; inputs on-chip, outputs require external resistors | min 3.135 · typ 3.3 · max 3.6 V | 48 |
| VCCIO VCCIO | BLVDS; inputs on-chip, outputs require external resistors | min 2.375 · typ 2.5 · max 2.625 V | 48 |
| VCCIO VCCIO | RSDS; inputs on-chip, outputs require external resistors | min 2.375 · typ 2.5 · max 2.625 V | 48 |
| VCCIO VCCIO | SSTL18D | min 1.71 · typ 1.8 · max 1.89 V | 48 |
| VCCIO VCCIO | SSTL25D | min 2.375 · typ 2.5 · max 2.625 V | 48 |
| VCCIO VCCIO | HSTL18D | min 1.71 · typ 1.8 · max 1.89 V | 48 |
| Input low voltage VIL | LVCMOS 3.3, LVTTL | min -0.3 · max 0.8 V | 49 |
| Input high voltage VIH | LVCMOS 3.3, LVTTL | min 2 · max 3.6 V | 49 |
| Input low voltage VIL | LVCMOS 2.5 | min -0.3 · max 0.7 V | 49 |
| Input high voltage VIH | LVCMOS 2.5 | min 1.7 · max 3.6 V | 49 |
| Input low voltage VIL | LVCMOS 1.8; maximum = 0.35VCCIO | min -0.3 V | 49 |
| Input high voltage VIH | LVCMOS 1.8; minimum = 0.65VCCIO | max 3.6 V | 49 |
| Input low voltage VIL | LVCMOS 1.5; maximum = 0.35VCCIO | min -0.3 V | 49 |
| Input high voltage VIH | LVCMOS 1.5; minimum = 0.65VCCIO | max 3.6 V | 49 |
| Input low voltage VIL | LVCMOS 1.2; maximum = 0.35VCCIO | min -0.3 V | 49 |
| Input high voltage VIH | LVCMOS 1.2; minimum = 0.65VCCIO | max 3.6 V | 49 |
| Input low voltage VIL | PCI; maximum = 0.3VCCIO | min -0.3 V | 49 |
| Input high voltage VIH | PCI; minimum = 0.5VCCIO | max 3.6 V | 49 |
| Output low current IOL | PCI; VOL maximum = 0.1VCCIO | max 1.5 mA | 49 |
| Output high current IOH | PCI; VOH minimum = 0.9VCCIO | max -0.5 mA | 49 |
| Input low voltage VIL | SSTL25 Class I; maximum = VREF – 0.18 | min -0.3 V | 49 |
| Input high voltage VIH | SSTL25 Class I; minimum = VREF + 0.18 | max 3.6 V | 49 |
| Output low voltage VOL | SSTL25 Class I | max 0.54 V | 49 |
| Output low current IOL | SSTL25 Class I | max 8 mA | 49 |
| Output high current IOH | SSTL25 Class I; VOH minimum = VCCIO - 0.62 | max 8 mA | 49 |
| Input low voltage VIL | SSTL25 Class II; maximum = VREF – 0.18 | min -0.3 V | 49 |
| Input high voltage VIH | SSTL25 Class II; minimum = VREF + 0.18 | max 3.6 V | 49 |
| Input low voltage VIL | SSTL18 Class I; maximum = VREF – 0.125 | min -0.3 V | 49 |
| Input high voltage VIH | SSTL18 Class I; minimum = VREF + 0.125 | max 3.6 V | 49 |
| Output low voltage VOL | SSTL18 Class I | max 0.4 V | 49 |
| Output low current IOL | SSTL18 Class I | max 8 mA | 49 |
| Output high current IOH | SSTL18 Class I; VOH minimum = VCCIO - 0.40 | max 8 mA | 49 |
| Input low voltage VIL | SSTL18 Class II; maximum = VREF – 0.125 | min -0.3 V | 49 |
| Input high voltage VIH | SSTL18 Class II; minimum = VREF + 0.125 | max 3.6 V | 49 |
| Input low voltage VIL | HSTL18 Class I; maximum = VREF – 0.1 | min -0.3 V | 49 |
| Input high voltage VIH | HSTL18 Class I; minimum = VREF + 0.1 | max 3.6 V | 49 |
| Output low voltage VOL | HSTL18 Class I | max 0.4 V | 49 |
| Output low current IOL | HSTL18 Class I | max 8 mA | 49 |
| Output high current IOH | HSTL18 Class I; VOH minimum = VCCIO - 0.40 | max 8 mA | 49 |
| Input low voltage VIL | HSTL18 Class II; maximum = VREF – 0.1 | min -0.3 V | 49 |
| Input high voltage VIH | HSTL18 Class II; minimum = VREF + 0.1 | max 3.6 V | 49 |
| Input low voltage VIL | LVCMOS25R33; maximum = VREF – 0.1 | min -0.3 V | 49 |
| Input high voltage VIH | LVCMOS25R33; minimum = VREF + 0.1 | max 3.6 V | 49 |
| Input low voltage VIL | LVCMOS18R33; maximum = VREF – 0.1 | min -0.3 V | 49 |
| Input high voltage VIH | LVCMOS18R33; minimum = VREF + 0.1 | max 3.6 V | 49 |
| Input low voltage VIL | LVCMOS18R25; maximum = VREF – 0.1 | min -0.3 V | 49 |
| Input high voltage VIH | LVCMOS18R25; minimum = VREF + 0.1 | max 3.6 V | 49 |
| Input low voltage VIL | LVCMOS15R33; maximum = VREF – 0.1 | min -0.3 V | 49 |
| Input high voltage VIH | LVCMOS15R33; minimum = VREF + 0.1 | max 3.6 V | 49 |
| Input low voltage VIL | LVCMOS15R25; maximum = VREF – 0.1 | min -0.3 V | 49 |
| Input high voltage VIH | LVCMOS15R25; minimum = VREF + 0.1 | max 3.6 V | 49 |
| Input low voltage VIL | LVCMOS12R33; maximum = VREF – 0.1 | min -0.3 V | 49 |
| Input high voltage VIH | LVCMOS12R33; minimum = VREF + 0.1 | max 3.6 V | 49 |
| Output low voltage VOL | LVCMOS12R33; open drain | max 0.4 V | 49 |
| Input low voltage VIL | LVCMOS12R25; maximum = VREF – 0.1 | min -0.3 V | 49 |
| Input high voltage VIH | LVCMOS12R25; minimum = VREF + 0.1 | max 3.6 V | 49 |
| Output low voltage VOL | LVCMOS12R25; open drain | max 0.4 V | 49 |
| Input low voltage VIL | LVCMOS10R33; maximum = VREF – 0.1 | min -0.3 V | 49 |
| Input high voltage VIH | LVCMOS10R33; minimum = VREF + 0.1 | max 3.6 V | 49 |
| Output low voltage VOL | LVCMOS10R33; open drain | max 0.4 V | 49 |
| Input low voltage VIL | LVCMOS10R25; maximum = VREF – 0.1 | min -0.3 V | 50 |
| Input high voltage VIH | LVCMOS10R25; minimum = VREF + 0.1 | max 3.6 V | 50 |
| Output low voltage VOL | LVCMOS10R25; open drain | max 0.4 V | 50 |
| VIL Max. VIL | LVCMOS 33; VCCIO = 1.5 V | max 0.685 V | 50 |
| VIL Max. VIL | LVCMOS 25; VCCIO = 1.5 V | max 0.687 V | 50 |
| VIL Max. VIL | LVCMOS 18; VCCIO = 1.5 V | max 0.655 V | 50 |
| Input Voltage VINP, VINM | Over Recommended Operating Conditions; VCCIO = 3.3 V | min 0 · max 2.605 V | 50 |
| Input Voltage VINP, VINM | Over Recommended Operating Conditions; VCCIO = 2.5 V | min 0 · max 2.05 V | 50 |
| Input Common Mode Voltage VCM | Over Recommended Operating Conditions; VCCIO = 3.3 V | min 0.05 · max 2.6 V | 50 |
| Input Common Mode Voltage VCM | Over Recommended Operating Conditions; VCCIO = 2.5 V | min 0.05 · max 2 V | 50 |
| Output high voltage for VOP or VOM VOH | Over Recommended Operating Conditions; RT = 100 Ohm | typ 1.375 V | 50 |
| Output low voltage for VOP or VOM VOL | Over Recommended Operating Conditions; RT = 100 Ohm | min 0.9 · typ 1.025 V | 50 |
| Output voltage differential VOD | Over Recommended Operating Conditions; (VOP - VOM), RT = 100 Ohm | min 250 · typ 350 · max 450 mV | 50 |
| Change in VOD between high and low VOD | Over Recommended Operating Conditions | max 50 mV | 50 |
| Output voltage offset VOS | Over Recommended Operating Conditions; (VOP + VOM)/2, RT = 100 Ohm | min 1.125 · typ 1.2 · max 1.395 V | 50 |
| Change in VOS between H and L VOS | Over Recommended Operating Conditions | max 50 mV | 50 |
| Output short circuit current IOSD | Over Recommended Operating Conditions; VOD = 0 V driver outputs shorted | max 24 mA | 50 |
| Output impedance ZOUT | Over Recommended Operating Conditions | typ 20 Ohms | 51 |
| Driver series resistor RS | Over Recommended Operating Conditions | typ 158 Ohms | 51 |
| Driver parallel resistor RP | Over Recommended Operating Conditions | typ 140 Ohms | 51 |
| Receiver termination RT | Over Recommended Operating Conditions | typ 100 Ohms | 51 |
| Output high voltage VOH | Over Recommended Operating Conditions | typ 1.43 V | 51 |
| Output low voltage VOL | Over Recommended Operating Conditions | typ 1.07 V | 51 |
| Output differential voltage VOD | Over Recommended Operating Conditions | typ 0.35 V | 51 |
| Output common mode voltage VCM | Over Recommended Operating Conditions | typ 1.25 V | 51 |
| Back impedance ZBACK | Over Recommended Operating Conditions | typ 100.5 Ohms | 51 |
| DC output current IDC | Over Recommended Operating Conditions | typ 6.03 mA | 51 |
| Output impedance ZOUT | Over Recommended Operating Conditions; nominal, Zo = 45 | typ 20 Ohms | 52 |
| Output impedance ZOUT | Over Recommended Operating Conditions; nominal, Zo = 90 | typ 20 Ohms | 52 |
| Driver series resistance RS | Over Recommended Operating Conditions; nominal, Zo = 45 | typ 80 Ohms | 52 |
| Driver series resistance RS | Over Recommended Operating Conditions; nominal, Zo = 90 | typ 80 Ohms | 52 |
| Left end termination RTLEFT | Over Recommended Operating Conditions; nominal, Zo = 45 | typ 45 Ohms | 52 |
| Left end termination RTLEFT | Over Recommended Operating Conditions; nominal, Zo = 90 | typ 90 Ohms | 52 |
| Right end termination RTRIGHT | Over Recommended Operating Conditions; nominal, Zo = 45 | typ 45 Ohms | 52 |
| Right end termination RTRIGHT | Over Recommended Operating Conditions; nominal, Zo = 90 | typ 90 Ohms | 52 |
| Output high voltage VOH | Over Recommended Operating Conditions; nominal, Zo = 45 | typ 1.376 V | 52 |
| Output high voltage VOH | Over Recommended Operating Conditions; nominal, Zo = 90 | typ 1.48 V | 52 |
| Output low voltage VOL | Over Recommended Operating Conditions; nominal, Zo = 45 | typ 1.124 V | 52 |
| Output low voltage VOL | Over Recommended Operating Conditions; nominal, Zo = 90 | typ 1.02 V | 52 |
| Output differential voltage VOD | Over Recommended Operating Conditions; nominal, Zo = 45 | typ 0.253 V | 52 |
| Output differential voltage VOD | Over Recommended Operating Conditions; nominal, Zo = 90 | typ 0.459 V | 52 |
| Output common mode voltage VCM | Over Recommended Operating Conditions; nominal, Zo = 45 | typ 1.25 V | 52 |
| Output common mode voltage VCM | Over Recommended Operating Conditions; nominal, Zo = 90 | typ 1.25 V | 52 |
| DC output current IDC | Over Recommended Operating Conditions; nominal, Zo = 45 | typ 11.236 mA | 52 |
| DC output current IDC | Over Recommended Operating Conditions; nominal, Zo = 90 | typ 10.204 mA | 52 |
| Output impedance ZOUT | Over Recommended Operating Conditions; nominal | typ 20 Ohms | 53 |
| Driver series resistor RS | Over Recommended Operating Conditions; nominal | typ 93 Ohms | 53 |
| Driver parallel resistor RP | Over Recommended Operating Conditions; nominal | typ 196 Ohms | 53 |
| Receiver termination RT | Over Recommended Operating Conditions; nominal | typ 100 Ohms | 53 |
| Output high voltage VOH | Over Recommended Operating Conditions; nominal | typ 2.05 V | 53 |
| Output low voltage VOL | Over Recommended Operating Conditions; nominal | typ 1.25 V | 53 |
| Output differential voltage VOD | Over Recommended Operating Conditions; nominal | typ 0.8 V | 53 |
| Output common mode voltage VCM | Over Recommended Operating Conditions; nominal | typ 1.65 V | 53 |
| Back impedance ZBACK | Over Recommended Operating Conditions; nominal | typ 100.5 Ohms | 53 |
| DC output current IDC | Over Recommended Operating Conditions; nominal | typ 12.11 mA | 53 |
| Frequency for Primary Clock Tree fMAX_PRI | All MachXO2 devices; –4; Over Recommended Operating Conditions | max 269 MHz | 58 |
| Clock Pulse Width for Primary Clock tW_PRI | All MachXO2 devices; –4; Over Recommended Operating Conditions | min 0.7 ns | 58 |
| Primary Clock Skew Within a Device tSKEW_PRI | MachXO2-1200HC-HE; –4; Over Recommended Operating Conditions | max 951 ps | 58 |
| Frequency for Edge Clock fMAX_EDGE | MachXO2-1200 and larger devices; –4; Over Recommended Operating Conditions | max 278 MHz | 58 |
| Best case propagation delay through one LUT-4 tPD | All MachXO2 devices; –4; Over Recommended Operating Conditions | max 7.24 ns | 58 |
| Clock to Output – PIO Output Register tCO | MachXO2-1200HC-HE; –4; Using Primary Clock without PLL; Over Recommended Operating Conditions | max 7.94 ns | 58 |
| Clock to Data Setup – PIO Input Register tSU | MachXO2-1200HC-HE; –4; Using Primary Clock without PLL; Over Recommended Operating Conditions | min -0.17 ns | 58 |
| Clock to Data Hold – PIO Input Register tH | MachXO2-1200HC-HE; –4; Using Primary Clock without PLL; Over Recommended Operating Conditions | min 2.36 ns | 58 |
| Clock to Data Setup – PIO Input Register with Data Input Delay tSU_DEL | MachXO2-1200HC-HE; –4; Using Primary Clock without PLL; Over Recommended Operating Conditions | min 2.17 ns | 59 |
| Clock to Data Hold – PIO Input Register with Input Data Delay tH_DEL | MachXO2-1200HC-HE; –4; Using Primary Clock without PLL; Over Recommended Operating Conditions | min -0.24 ns | 59 |
| Clock Frequency of I/O and PFU Register fMAX_IO | All MachXO2 devices; –4; Over Recommended Operating Conditions | max 269 MHz | 59 |
| Clock to Output – PIO Output Register tCOE | MachXO2-1200HC-HE; –4; Using Edge Clock without PLL; Over Recommended Operating Conditions | max 8.1 ns | 59 |
| Clock to Data Setup – PIO Input Register tSUE | MachXO2-1200HC-HE; –4; Using Edge Clock without PLL; Over Recommended Operating Conditions | min -0.19 ns | 59 |
| Clock to Data Hold – PIO Input Register tHE | MachXO2-1200HC-HE; –4; Using Edge Clock without PLL; Over Recommended Operating Conditions | min 2.52 ns | 59 |
| Clock to Data Setup – PIO Input Register with Data Input Delay tSU_DELE | MachXO2-1200HC-HE; –4; Using Edge Clock without PLL; Over Recommended Operating Conditions | min 2.05 ns | 59 |
| Clock to Data Hold – PIO Input Register with Input Data Delay tH_DELE | MachXO2-1200HC-HE; –4; Using Edge Clock without PLL; Over Recommended Operating Conditions | min -0.23 ns | 59 |
| Clock to Output – PIO Output Register tCOPLL | MachXO2-1200HC-HE; –4; Using Primary Clock with PLL; Over Recommended Operating Conditions | max 6.13 ns | 59 |
| Clock to Data Setup – PIO Input Register tSUPLL | MachXO2-1200HC-HE; –4; Using Primary Clock with PLL; Over Recommended Operating Conditions | min 0.65 ns | 59 |
| Clock to Data Hold – PIO Input Register tHPLL | MachXO2-1200HC-HE; –4; Using Primary Clock with PLL; Over Recommended Operating Conditions | min 0.55 ns | 60 |
| Clock to Data Setup – PIO Input Register with Data Input Delay tSU_DELPLL | MachXO2-1200HC-HE; –4; Using Primary Clock with PLL; Over Recommended Operating Conditions | min 3.72 ns | 60 |
| Clock to Data Hold – PIO Input Register with Input Data Delay tH_DELPLL | MachXO2-1200HC-HE; –4; Using Primary Clock with PLL; Over Recommended Operating Conditions | min -0.83 ns | 60 |
| Input Data Valid After CLK tDVA | –4; All MachXO2 devices, all sides; GDDRX1_RX.SCLK.Aligned; Over Recommended Operating Conditions | max 0.368 UI | 60 |
| Input Data Hold After CLK tDVE | –4; All MachXO2 devices, all sides; GDDRX1_RX.SCLK.Aligned; Over Recommended Operating Conditions | min 0.668 UI | 60 |
| DDRX1 Input Data Speed fDATA | –4; All MachXO2 devices, all sides; GDDRX1_RX.SCLK.Aligned; Over Recommended Operating Conditions | max 208 Mbps | 60 |
| DDRX1 SCLK Frequency fDDRX1 | –4; All MachXO2 devices, all sides; GDDRX1_RX.SCLK.Aligned; Over Recommended Operating Conditions | max 104 MHz | 60 |
| Input Data Setup Before CLK tSU | –4; All MachXO2 devices, all sides; GDDRX1_RX.SCLK.Centered; Over Recommended Operating Conditions | min 0.538 ns | 60 |
| Input Data Hold After CLK tHO | –4; All MachXO2 devices, all sides; GDDRX1_RX.SCLK.Centered; Over Recommended Operating Conditions | min 1.09 ns | 60 |
| DDRX1 Input Data Speed fDATA | –4; All MachXO2 devices, all sides; GDDRX1_RX.SCLK.Centered; Over Recommended Operating Conditions | max 208 Mbps | 60 |
| DDRX1 SCLK Frequency fDDRX1 | –4; All MachXO2 devices, all sides; GDDRX1_RX.SCLK.Centered; Over Recommended Operating Conditions | max 104 MHz | 60 |
| Input Data Valid After CLK tDVA | –4; MachXO2-1200, bottom side only; GDDRX2_RX.ECLK.Aligned; Over Recommended Operating Conditions | max 0.364 UI | 60 |
| Input Data Hold After CLK tDVE | –4; MachXO2-1200, bottom side only; GDDRX2_RX.ECLK.Aligned; Over Recommended Operating Conditions | min 0.679 UI | 60 |
| DDRX2 Serial Input Data Speed fDATA | –4; MachXO2-1200, bottom side only; GDDRX2_RX.ECLK.Aligned; Over Recommended Operating Conditions | max 462 Mbps | 60 |
| DDRX2 ECLK Frequency fDDRX2 | –4; MachXO2-1200, bottom side only; GDDRX2_RX.ECLK.Aligned; Over Recommended Operating Conditions | max 231 MHz | 60 |
| SCLK Frequency fSCLK | –4; MachXO2-1200, bottom side only; GDDRX2_RX.ECLK.Aligned; Over Recommended Operating Conditions | max 116 MHz | 60 |
| Input Data Setup Before CLK tSU | –4; MachXO2-1200, bottom side only; GDDRX2_RX.ECLK.Centered; Over Recommended Operating Conditions | min 0.198 ns | 60 |
| Input Data Hold After CLK tHO | –4; MachXO2-1200, bottom side only; GDDRX2_RX.ECLK.Centered; Over Recommended Operating Conditions | min 0.344 ns | 60 |
| DDRX2 Serial Input Data Speed fDATA | –4; MachXO2-1200, bottom side only; GDDRX2_RX.ECLK.Centered; Over Recommended Operating Conditions | max 462 Mbps | 60 |
| DDRX2 ECLK Frequency fDDRX2 | –4; MachXO2-1200, bottom side only; GDDRX2_RX.ECLK.Centered; Over Recommended Operating Conditions | max 231 MHz | 60 |
| SCLK Frequency fSCLK | –4; MachXO2-1200, bottom side only; GDDRX2_RX.ECLK.Centered; Over Recommended Operating Conditions | max 116 MHz | 60 |
| Input Data Valid After ECLK tDVA | –4; MachXO2-1200, bottom side only; GDDRX4_RX.ECLK.Aligned; Over Recommended Operating Conditions | max 0.345 UI | 61 |
| Input Data Hold After ECLK tDVE | –4; MachXO2-1200, bottom side only; GDDRX4_RX.ECLK.Aligned; Over Recommended Operating Conditions | min 0.703 UI | 61 |
| DDRX4 Serial Input Data Speed fDATA | –4; MachXO2-1200, bottom side only; GDDRX4_RX.ECLK.Aligned; Over Recommended Operating Conditions | max 524 Mbps | 61 |
| DDRX4 ECLK Frequency fDDRX4 | –4; MachXO2-1200, bottom side only; GDDRX4_RX.ECLK.Aligned; Over Recommended Operating Conditions | max 262 MHz | 61 |
| SCLK Frequency fSCLK | –4; MachXO2-1200, bottom side only; GDDRX4_RX.ECLK.Aligned; Over Recommended Operating Conditions | max 66 MHz | 61 |
| Input Data Setup Before ECLK tSU | –4; MachXO2-1200, bottom side only; GDDRX4_RX.ECLK.Centered; Over Recommended Operating Conditions | min 0.198 ns | 61 |
| Input Data Hold After ECLK tHO | –4; MachXO2-1200, bottom side only; GDDRX4_RX.ECLK.Centered; Over Recommended Operating Conditions | min 0.344 ns | 61 |
| DDRX4 Serial Input Data Speed fDATA | –4; MachXO2-1200, bottom side only; GDDRX4_RX.ECLK.Centered; Over Recommended Operating Conditions | max 524 Mbps | 61 |
| DDRX4 ECLK Frequency fDDRX4 | –4; MachXO2-1200, bottom side only; GDDRX4_RX.ECLK.Centered; Over Recommended Operating Conditions | max 262 MHz | 61 |
| SCLK Frequency fSCLK | –4; MachXO2-1200, bottom side only; GDDRX4_RX.ECLK.Centered; Over Recommended Operating Conditions | max 66 MHz | 61 |
| Input Data Valid After ECLK tDVA | –4; MachXO2-1200, bottom side only; GDDR71_RX.ECLK.7:1; Over Recommended Operating Conditions | max 0.345 UI | 61 |
| Input Data Hold After ECLK tDVE | –4; MachXO2-1200, bottom side only; GDDR71_RX.ECLK.7:1; Over Recommended Operating Conditions | min 0.703 UI | 61 |
| DDR71 Serial Input Data Speed fDATA | –4; MachXO2-1200, bottom side only; GDDR71_RX.ECLK.7:1; Over Recommended Operating Conditions | max 524 Mbps | 61 |
| DDR71 ECLK Frequency fDDR71 | –4; MachXO2-1200, bottom side only; GDDR71_RX.ECLK.7:1; Over Recommended Operating Conditions | max 262 MHz | 61 |
| 7:1 Input Clock Frequency (SCLK) (minimum limited by PLL) fCLKIN | –4; MachXO2-1200, bottom side only; GDDR71_RX.ECLK.7:1; Over Recommended Operating Conditions | max 75 MHz | 61 |
| Output Data Invalid After CLK Output tDIA | –4; All MachXO2 devices, all sides; GDDRX1_TX.SCLK.Aligned; Over Recommended Operating Conditions | max 0.58 ns | 61 |
| Output Data Invalid Before CLK Output tDIB | –4; All MachXO2 devices, all sides; GDDRX1_TX.SCLK.Aligned; Over Recommended Operating Conditions | max 0.58 ns | 61 |
| DDRX1 Output Data Speed fDATA | –4; All MachXO2 devices, all sides; GDDRX1_TX.SCLK.Aligned; Over Recommended Operating Conditions | max 208 Mbps | 61 |
| DDRX1 SCLK frequency fDDRX1 | –4; All MachXO2 devices, all sides; GDDRX1_TX.SCLK.Aligned; Over Recommended Operating Conditions | max 104 MHz | 61 |
| Output Data Valid Before CLK Output tDVB | –4; All MachXO2 devices, all sides; GDDRX1_TX.SCLK.Centered; Over Recommended Operating Conditions | min 1.87 ns | 61 |
| Output Data Valid After CLK Output tDVA | –4; All MachXO2 devices, all sides; GDDRX1_TX.SCLK.Centered; Over Recommended Operating Conditions | min 1.87 ns | 61 |
| DDRX1 Output Data Speed fDATA | –4; All MachXO2 devices, all sides; GDDRX1_TX.SCLK.Centered; Over Recommended Operating Conditions | max 208 Mbps | 61 |
| DDRX1 SCLK Frequency (minimum limited by PLL) fDDRX1 | –4; All MachXO2 devices, all sides; GDDRX1_TX.SCLK.Centered; Over Recommended Operating Conditions | max 104 MHz | 61 |
| Output Data Invalid After CLK Output tDIA | –4; MachXO2-1200, top side only; GDDRX2_TX.ECLK.Aligned; Over Recommended Operating Conditions | max 0.23 ns | 61 |
| Output Data Invalid Before CLK Output tDIB | –4; MachXO2-1200, top side only; GDDRX2_TX.ECLK.Aligned; Over Recommended Operating Conditions | max 0.23 ns | 61 |
| DDRX2 Serial Output Data Speed fDATA | –4; MachXO2-1200, top side only; GDDRX2_TX.ECLK.Aligned; Over Recommended Operating Conditions | max 462 Mbps | 61 |
| DDRX2 ECLK frequency fDDRX2 | –4; MachXO2-1200, top side only; GDDRX2_TX.ECLK.Aligned; Over Recommended Operating Conditions | max 231 MHz | 61 |
| SCLK Frequency fSCLK | –4; MachXO2-1200, top side only; GDDRX2_TX.ECLK.Aligned; Over Recommended Operating Conditions | max 116 MHz | 61 |
| Output Data Valid Before CLK Output tDVB | –4; MachXO2-1200, top side only; GDDRX2_TX.ECLK.Centered; Over Recommended Operating Conditions | min 0.83 ns | 62 |
| Output Data Valid After CLK Output tDVA | –4; MachXO2-1200, top side only; GDDRX2_TX.ECLK.Centered; Over Recommended Operating Conditions | min 0.83 ns | 62 |
| DDRX2 Serial Output Data Speed fDATA | –4; MachXO2-1200, top side only; GDDRX2_TX.ECLK.Centered; Over Recommended Operating Conditions | max 462 Mbps | 62 |
| DDRX2 ECLK Frequency (minimum limited by PLL) fDDRX2 | –4; MachXO2-1200, top side only; GDDRX2_TX.ECLK.Centered; Over Recommended Operating Conditions | max 231 MHz | 62 |
| SCLK Frequency fSCLK | –4; MachXO2-1200, top side only; GDDRX2_TX.ECLK.Centered; Over Recommended Operating Conditions | max 116 MHz | 62 |
| Output Data Invalid After CLK Output tDIA | –4; MachXO2-1200, top side only; GDDRX4_TX.ECLK.Aligned; Over Recommended Operating Conditions | max 0.23 ns | 62 |
| Output Data Invalid Before CLK Output tDIB | –4; MachXO2-1200, top side only; GDDRX4_TX.ECLK.Aligned; Over Recommended Operating Conditions | max 0.23 ns | 62 |
| DDRX4 Serial Output Data Speed fDATA | –4; MachXO2-1200, top side only; GDDRX4_TX.ECLK.Aligned; Over Recommended Operating Conditions | max 524 Mbps | 62 |
| DDRX4 ECLK Frequency fDDRX4 | –4; MachXO2-1200, top side only; GDDRX4_TX.ECLK.Aligned; Over Recommended Operating Conditions | max 262 MHz | 62 |
| SCLK Frequency fSCLK | –4; MachXO2-1200, top side only; GDDRX4_TX.ECLK.Aligned; Over Recommended Operating Conditions | max 66 MHz | 62 |
| Output Data Valid Before CLK Output tDVB | –4; MachXO2-1200, top side only; GDDRX4_TX.ECLK.Centered; Over Recommended Operating Conditions | min 0.71 ns | 62 |
| Output Data Valid After CLK Output tDVA | –4; MachXO2-1200, top side only; GDDRX4_TX.ECLK.Centered; Over Recommended Operating Conditions | min 0.71 ns | 62 |
| DDRX4 Serial Output Data Speed fDATA | –4; MachXO2-1200, top side only; GDDRX4_TX.ECLK.Centered; Over Recommended Operating Conditions | max 524 Mbps | 62 |
| DDRX4 ECLK Frequency (minimum limited by PLL) fDDRX4 | –4; MachXO2-1200, top side only; GDDRX4_TX.ECLK.Centered; Over Recommended Operating Conditions | max 262 MHz | 62 |
| SCLK Frequency fSCLK | –4; MachXO2-1200, top side only; GDDRX4_TX.ECLK.Centered; Over Recommended Operating Conditions | max 66 MHz | 62 |
| Output Data Invalid Before CLK Output tDIB | –4; MachXO2-1200, top side only; GDDR71_TX.ECLK.7:1; Over Recommended Operating Conditions | max 0.2 ns | 62 |
| Output Data Invalid After CLK Output tDIA | –4; MachXO2-1200, top side only; GDDR71_TX.ECLK.7:1; Over Recommended Operating Conditions | max 0.2 ns | 62 |
| DDR71 Serial Output Data Speed fDATA | –4; MachXO2-1200, top side only; GDDR71_TX.ECLK.7:1; Over Recommended Operating Conditions | max 524 Mbps | 62 |
| DDR71 ECLK Frequency fDDR71 | –4; MachXO2-1200, top side only; GDDR71_TX.ECLK.7:1; Over Recommended Operating Conditions | max 262 MHz | 62 |
| 7:1 Output Clock Frequency (SCLK) (minimum limited by PLL) fCLKOUT | –4; MachXO2-1200, top side only; GDDR71_TX.ECLK.7:1; Over Recommended Operating Conditions | max 75 MHz | 62 |
| Input Clock Frequency (CLKI, CLKFB) fIN | Over Recommended Operating Conditions | min 7 · max 400 MHz | 72 |
| Output Clock Frequency (CLKOP, CLKOS, CLKOS2) fOUT | Over Recommended Operating Conditions | min 1.5625 · max 400 MHz | 72 |
| Output Frequency (CLKOS3 cascaded from CLKOS2) fOUT2 | Over Recommended Operating Conditions | min 0.0122 · max 400 MHz | 72 |
| PLL VCO Frequency fVCO | Over Recommended Operating Conditions | min 200 · max 800 MHz | 72 |
| Phase Detector Input Frequency fPFD | Over Recommended Operating Conditions | min 7 · max 400 MHz | 72 |
| Output Clock Duty Cycle tDT | Without duty trim selected; using LVDS output buffers | min 45 · max 55 % | 72 |
| Edge Duty Trim Accuracy tDT_TRIM | Percentage of the setting value | min -75 · max 75 % | 72 |
| Output Phase Accuracy tPH | CLKOS compared to CLKOP for one phase step at maximum VCO frequency | min -6 · max 6 % | 72 |
| Output Clock Period Jitter tOPJIT | fOUT > 100 MHz | max 150 ps p-p | 72 |
| Output Clock Period Jitter tOPJIT | fOUT < 100 MHz | max 0.007 UIPP | 72 |
| Output Clock Cycle-to-cycle Jitter tOPJIT | fOUT > 100 MHz | max 180 ps p-p | 72 |
| Output Clock Cycle-to-cycle Jitter tOPJIT | fOUT < 100 MHz | max 0.009 UIPP | 72 |
| Output Clock Phase Jitter tOPJIT | fPFD > 100 MHz | max 160 ps p-p | 72 |
| Output Clock Phase Jitter tOPJIT | fPFD < 100 MHz | max 0.011 UIPP | 72 |
| Output Clock Period Jitter (Fractional-N) tOPJIT | fOUT > 100 MHz | max 230 ps p-p | 72 |
| Output Clock Period Jitter (Fractional-N) tOPJIT | fOUT < 100 MHz | max 0.12 UIPP | 72 |
| Output Clock Cycle-to-cycle Jitter (Fractional-N) tOPJIT | fOUT > 100 MHz | max 230 ps p-p | 72 |
| Output Clock Cycle-to-cycle Jitter (Fractional-N) tOPJIT | fOUT < 100 MHz | max 0.12 UIPP | 72 |
| Static Phase Offset tSPO | Divider ratio = integer | min -120 · max 120 ps | 72 |
| Output Clock Pulse Width tW | At 90% or 10%; using LVDS output buffers | min 0.9 ns | 72 |
| PLL Lock-in Time tLOCK | At minimum fPFD | max 15 ms | 72 |
| PLL Unlock Time tUNLOCK | Over Recommended Operating Conditions | max 50 ns | 72 |
| Input Clock Period Jitter tIPJIT | fPFD ≥ 20 MHz | max 1000 ps p-p | 72 |
| Input Clock Period Jitter tIPJIT | fPFD < 20 MHz | max 0.02 UIPP | 72 |
| Input Clock High Time tHI | 90% to 90% | min 0.5 ns | 72 |
| Input Clock Low Time tLO | 10% to 10% | min 0.5 ns | 72 |
| STANDBY High to PLL Stable tSTABLE | At minimum fPFD | max 15 ms | 72 |
| RST/RESETM Pulse Width tRST | Over Recommended Operating Conditions | min 1 ns | 72 |
| RST Recovery Time tRSTREC | Over Recommended Operating Conditions | min 1 ns | 72 |
| RESETC/D Pulse Width tRST_DIV | Over Recommended Operating Conditions | min 10 ns | 72 |
| RESETC/D Recovery Time tRSTREC_DIV | Over Recommended Operating Conditions | min 1 ns | 72 |
| PHASESTEP Setup Time tROTATE-SETUP | Over Recommended Operating Conditions | min 10 ns | 72 |
| PHASESTEP Pulse Width tROTATE_WD | Over Recommended Operating Conditions | min 4 VCO Cycles | 73 |
| Oscillator Output Frequency (Industrial Grade Devices, –40 °C to 100 °C) fMAX | Industrial Grade Devices | min 124.355 · typ 133 · max 141.645 MHz | 74 |
| Output Clock Duty Cycle tDT | min 43 · typ 50 · max 57 % | 74 | |
| Output Clock Period Jitter tOPJIT | 133 MHz | min 0.01 · typ 0.012 · max 0.02 UIPP | 74 |
| STDBY Low to Oscillator Stable tSTABLEOSC | min 0.01 · typ 0.05 · max 0.1 us | 74 | |
| USERSTDBY High to Stop tPWRDN | All HC/HE devices | max 9 ns | 74 |
| USERSTDBY Low to Power Up tPWRUP | LCMXO2-1200; HC/HE devices | min 20 · max 50 us | 74 |
| USERSTDBY Pulse Width tWSTDBY | All HC/HE devices | min 18 ns | 74 |
Open-source boards using it
3- 6 layers100 × 100 mm

- 8 layers50 × 50 mm

- 8 layers50 × 50 mm

Parts like it
8LCMXO2-1200ZE-1SG32I
QFN-32-EP(5x5)-40℃~+100℃ 1.14V~1.26V 1280 160 21 65536bit MachXO2 Supports hot swap、Supports watchdog timeout detection QFN-32-EP(5x5) Programmable Logic Device (CPLDs/FPGAs) ROHSLatticeProgrammable Logic Device (CPLDs/FPGAs)XC2C32A-6QFG32C
QFN-32(5x5)QFN-32(5x5) Programmable Logic Device (CPLDs/FPGAs) ROHSAMD/XILINXProgrammable Logic Device (CPLDs/FPGAs)ISPGAL22V10AB-75LN
QFN-32(5x5)0℃~+75℃ 10 7.5ns EEPLD Supports hot swap ispGAL QFN-32(5x5) Programmable Logic Device (CPLDs/FPGAs)LatticeProgrammable Logic Device (CPLDs/FPGAs)ISPGAL22V10AC-75LN
QFN-32(5x5)0℃~+75℃ 10 7.5ns EEPLD Supports hot swap ispGAL QFN-32(5x5) Programmable Logic Device (CPLDs/FPGAs)LatticeProgrammable Logic Device (CPLDs/FPGAs)XC2C32A-4QFG32C
QFN-32-EP(5x5)Supports hot swap QFN-32-EP(5x5) Programmable Logic Device (CPLDs/FPGAs) ROHSAMD/XILINXProgrammable Logic Device (CPLDs/FPGAs)XC2C32A-6QFG32I
QFN-32-EP(5x5)Supports hot swap QFN-32-EP(5x5) Programmable Logic Device (CPLDs/FPGAs) ROHSAMD/XILINXProgrammable Logic Device (CPLDs/FPGAs)LCMXO2-1200HC-5SG32C
QFN-32-EP(5x5)0℃~+85℃ 1280 160 2.375V~3.465V 21 65536bit MachXO2 Supports hot swap、Supports watchdog timeout detection QFN-32-EP(5x5) Programmable Logic Device (CPLDs/FPGAs) ROHSLatticeProgrammable Logic Device (CPLDs/FPGAs)LCMXO2-1200HC-6SG32I
QFN-32-EP(5x5)-40℃~+100℃ 1280 160 2.375V~3.465V 21 65536bit MachXO2 Supports hot swap、Supports watchdog timeout detection QFN-32-EP(5x5) Programmable Logic Device (CPLDs/FPGAs) ROHSLatticeProgrammable Logic Device (CPLDs/FPGAs)
Questions
Is there a KiCad symbol and footprint for the LCMXO2-1200HC-4SG32I?
Yes. The symbol is EasyEDA_Cloud:LCMXO2-1200ZE-2SG32I and the footprint EasyEDA_Cloud:QFN-32_L5.0-W5.0-P0.50-TL-EP3.5, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the LCMXO2-1200HC-4SG32I?
QFN-32-EP(5x5), with 33 pins. Its footprint is drawn on this page.
Where is the LCMXO2-1200HC-4SG32I datasheet?
Lattice publishes it: the Datasheet link on this page opens it.
Where can I order the LCMXO2-1200HC-4SG32I?
JLCPCB lists it as part C1551142, with 54 in stock; the sellers' links on this page open their listings.
What can replace the LCMXO2-1200HC-4SG32I?
Parts like it in the library: the LCMXO2-1200ZE-1SG32I by Lattice, the XC2C32A-6QFG32C by AMD/XILINX, the ISPGAL22V10AB-75LN by Lattice and the ISPGAL22V10AC-75LN by Lattice. Check their datasheets: a part that fits the footprint may still differ in its ratings.
Which open-source boards use the LCMXO2-1200HC-4SG32I?
3 boards in 3 repositories on GitHub; the most starred are listed on this page, with their KiCad files.