Skip to the content
123456789

MR25H10CDFR

Everspin TechExtended

1Mbit MRAM SPI DFN-8-EP(5x6) Random Access Memory (RAM) ROHS

Part id
everspin-tech/MR25H10CDFR
Category
Random Access Memory (RAM)
Package
DFN-8-EP(5x6)
Pins
9
In stock
0 at JLCPCB (C17498373)

Overview

The MR25H10CDFR is a random Access Memory made by Everspin Tech in a DFN-8-EP(5x6) package with 9 pins. 1Mbit MRAM SPI DFN-8-EP(5x6) Random Access Memory (RAM) ROHS.

PCBKit's library has its KiCad symbol (EasyEDA_Cloud:FM25V10-DGTR, from EasyEDA) and its footprint (EasyEDA_Cloud:DFN-8_L5.0-W6.0-P1.27-BL-EP, from EasyEDA), ready for a KiCad board. JLCPCB lists it (part C17498373).

Symbol

6SCK5SI2SO1CS#7HOLD#3WP#9EP4VSS8VDD
EasyEDA_Cloud:FM25V10-DGTRFrom EasyEDA

Footprint

123456789
EasyEDA_Cloud:DFN-8_L5.0-W6.0-P1.27-BL-EPFrom EasyEDA

From the datasheet

9
Supply, least
2.7 V · VDD, recommended operating minimum, Industrial · p. 11
Supply, most
3.6 V · VDD, recommended operating maximum, Industrial · p. 11
Supply, absolute maximum
4 V · VDD, absolute maximum · p. 10
Works from
-40 °C · Industrial operating ambient minimum · p. 11
Works up to
85 °C · Industrial operating ambient maximum · p. 11
Takes working
6 mA · VDD, active read at 40 MHz, typical · p. 11
Takes at most
27 mA · VDD, active write at 40 MHz, max · p. 11
Takes asleep
7 µA · VDD, sleep mode, CS high and SPI bus inactive, typical · p. 11
A pin gives at most
20 mA · Output current per pin, absolute maximum magnitude · p. 10

What it is and has

8
Memory
1,048,576-bit MRAM · p. 1
Write delays
None · p. 1
Write endurance
Unlimited · p. 1
Data retention
Greater than 20 years · p. 1
Protection
Automatic data protection on power loss · p. 1
Protection
Block write protection · p. 1
Interface
SPI, up to 40 MHz clock · p. 1
Package
8-pin DFN Small Flag, 5 mm x 6 mm · p. 1

Specifications

23
ParameterConditionsAs printedPage
Supply voltage2 VDDAll voltages referenced to VSSmin -0.5 · max 4 V10
Voltage on any pin2 VINUpper limit VDD + 0.5 V; all voltages referenced to VSSmin -0.5 V10
Output current per pin IOUTLimit ±20 mAmin -20 · max 20 mA10
Package power dissipation 3 PDPower dissipation capability depends on package characteristics and use environmentmax 0.6 W10
Temperature under bias TBIASIndustrialmin -45 · max 95 °C10
Storage Temperature Tstgmin -55 · max 150 °C10
Lead temperature TLead3 minutes maxmax 260 °C10
Maximum magnetic field exposure Hmax_writeWritemax 12000 A/m10
Maximum magnetic field exposure Hmax_readRead or Standbymax 12000 A/m10
Power supply voltage VDDIndustrialmin 2.7 · max 3.6 V11
Input high voltage VIHAll; upper limit VDD + 0.3 Vmin 2.2 V11
Input low voltage VILAllmin -0.5 · max 0.8 V11
Temperature under bias TAIndustrialmin -40 · max 85 °C11
Input leakage current ILIMaximum ±1 uAmax 1 uA11
Output leakage current ILOMaximum ±1 uAmax 1 uA11
Output low voltage VOLIOL = +4 mAmax 0.4 V11
Output high voltage VOH(IOH = -4 mA)min 2.4 V11
Active Read Current IDDR1 MHztyp 2.5 · max 3 mA11
Active Read Current IDDR40 MHztyp 6 · max 10 mA11
Active Write Current IDDW1 MHztyp 8 · max 13 mA11
Active Write Current IDDW40 MHztyp 23 · max 27 mA11
Standby Current ISBCS high and SPI bus inactivetyp 90 · max 115 uA11
Standby Sleep Mode Current IzzCS high and SPI bus inactivetyp 7 · max 30 uA11

Pins, by the datasheet

8
1 CS
Active low chip select; high powers down memory, ignores inputs and makes SO Hi-Z. · p. 3
2 SO
Serial data output during reads; otherwise Hi-Z, including while HOLD is low; transitions on falling SCK edges. · p. 3
3 WP
Low prevents writes to the Status Register. · p. 3
4 VSS
Power supply ground pin. · p. 3
5 SI
Serial data input sampled on rising SCK edges; may be tied to SO for a single bidirectional data bus. · p. 3
6 SCK
Serial clock up to 40 MHz; supports SPI modes 0 and 3 and can be stopped at any time. · p. 3
7 HOLD
Low suspends the operation and ignores CS and SCK transitions; HOLD transitions must occur while CS is low. · p. 3
8 VDD
Power supply voltage from +2.7 to +3.6 volts. · p. 3

Ordering codes, by the datasheet

8
MR25H10CDC
8-DFN · Industrial, -40 to +85 C; tray; not recommended for new designs · p. 16
MR25H10CDCR
8-DFN · Industrial, -40 to +85 C; tape and reel; not recommended for new designs · p. 16
MR25H10CDF
Small Flag 8-DFN · Industrial, -40 to +85 C; tray · p. 16
MR25H10CDFR
Small Flag 8-DFN · Industrial, -40 to +85 C; tape and reel · p. 16
MR25H10MDC
8-DFN · AEC-Q100 Grade 1, -40 to +125 C; tray; not recommended for new designs · p. 16
MR25H10MDCR
8-DFN · AEC-Q100 Grade 1, -40 to +125 C; tape and reel; not recommended for new designs · p. 16
MR25H10MDF
Small Flag 8-DFN · AEC-Q100 Grade 1, -40 to +125 C; tray · p. 16
MR25H10MDFR
Small Flag 8-DFN · AEC-Q100 Grade 1, -40 to +125 C; tape and reel · p. 16

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the MR25H10CDFR?

Yes. The symbol is EasyEDA_Cloud:FM25V10-DGTR and the footprint EasyEDA_Cloud:DFN-8_L5.0-W6.0-P1.27-BL-EP, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the MR25H10CDFR?

DFN-8-EP(5x6), with 9 pins. Its footprint is drawn on this page.

Where is the MR25H10CDFR datasheet?

Everspin Tech publishes it: the Datasheet link on this page opens it.

Where can I order the MR25H10CDFR?

JLCPCB lists it as part C17498373, with 0 in stock; the sellers' links on this page open their listings.

What can replace the MR25H10CDFR?

Parts like it in the library: the MR20H40CDF by Everspin Tech, the MR25H40MDF by Everspin Tech, the MR25H256AMDF by Everspin Tech and the MR25H256CDF by Everspin Tech. Check their datasheets: a part that fits the footprint may still differ in its ratings.