AP62600SJ
Diodes IncorporatedExtended
-40℃~+125℃ 1 360uA 4.5V~18V 400kHz~1.2MHz 600mV~7V 6A Adjustable Buck Buck Built-in Yes QFN-12(2x3) DC-DC Converters ROHS
- Part id
- diodes/AP62600SJ
- Category
- DC DC Converters
- Package
- QFN-12(2x3)
- Pins
- 12
- In stock
- 1,597 at JLCPCB (C4748917)
Overview
The AP62600SJ is a DC DC Converter made by Diodes Incorporated in a QFN-12(2x3) package with 12 pins. -40℃~+125℃ 1 360uA 4.5V~18V 400kHz~1.2MHz 600mV~7V 6A Adjustable Buck Buck Built-in Yes QFN-12(2x3) DC-DC Converters ROHS.
PCBKit's library has its KiCad symbol (AP62600SJ-7:AP62600SJ-7, from Antmicro) and its footprint (Horizon_manufacturer:V-QFN2030-12, from Horizon), ready for a KiCad board. 1,597 are in stock at JLCPCB (part C4748917).
Symbol
Footprint
From the datasheet
16- Supply, least
- 4.5 V · VIN, recommended operating min · p. 5
- Supply, most
- 18 V · VIN, recommended operating max · p. 5
- Supply, absolute maximum
- 20 V · VIN, DC absolute max · p. 5
- Works from
- -40 °C · Operating ambient temperature min · p. 5
- Works up to
- 85 °C · Operating ambient temperature max · p. 5
- Junction, hottest
- 150 °C · Junction temperature absolute max · p. 5
- Takes working
- 360 µA · VIN quiescent current typical, no load and non-switching · p. 15
- Takes asleep
- 1 µA · Shutdown supply current typical, VEN = 0V · p. 6
- Gives
- 6 A · Continuous output current rating · p. 1
- Current limit
- 8.5 A · LS valley current limit typical, source to drain · p. 6
- Feedback reference
- 600 mV · Feedback voltage typical, CCM · p. 6
- Switches at
- 400 kHz · Oscillator frequency typical, FSEL = GND, VOUT = 5V, CCM · p. 6
- Switches at
- 800 kHz · Oscillator frequency typical, FSEL floating, VOUT = 5V, CCM · p. 6
- Switches at
- 1.2 MHz · Oscillator frequency typical, FSEL = VCC, VOUT = 5V, CCM · p. 6
- Junction to air (V-QFN2030-12 (Type A))
- 40 K/W · Junction to ambient rating · p. 5
- Junction to case (V-QFN2030-12 (Type A))
- 5.5 K/W · Junction to case rating · p. 5
What it is and has
10- Input voltage
- 4.5V to 18V · p. 1
- Output voltage range
- 0.6V to 7V · p. 1
- Continuous output current
- 6A · p. 1
- Reference voltage accuracy
- 0.6V ± 1% · p. 1
- Soft-start
- Programmable · p. 1
- Power-good indicator
- Available · p. 1
- Protection
- Undervoltage lockout · p. 1
- Protection
- Cycle-by-cycle valley current limit · p. 1
- Protection
- Thermal shutdown · p. 1
- Package
- V-QFN2030-12 (Type A) · p. 1
Around it
3- cap 100nF
- between BST and SW; Recommended to power the high-side driver. · p. 3
- cap 1μF
- between VCC and PGND; Place as close as possible to VCC and PGND. · p. 3
- res 100kΩ
- between PG and VCC; External power-good pull-up resistor. · p. 18
Specifications
55| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Supply Pin Voltage VIN | TA = +25°C; DC | min -0.3 · max 20 V | 5 |
| Supply Pin Voltage VIN | TA = +25°C; 400ms | min -0.3 · max 22 V | 5 |
| VCC Pin Voltage VCC | TA = +25°C | min -0.3 · max 6 V | 5 |
| Enable/UVLO Pin Voltage VEN | TA = +25°C | min -0.3 · max 6 V | 5 |
| MODE Select Pin Voltage VMODE | TA = +25°C | min -0.3 · max 6 V | 5 |
| Frequency Select Pin Voltage VFSEL | TA = +25°C | min -0.3 · max 6 V | 5 |
| Power-Good Pin Voltage VPG | TA = +25°C | min -0.3 · max 6 V | 5 |
| Switch Pin Voltage VSW | TA = +25°C; DC; maximum VIN + 0.3 V | min -1 V | 5 |
| Switch Pin Voltage VSW | TA = +25°C; 20ns; maximum VIN + 2.0 V | min -2.5 V | 5 |
| Soft-Start/Tracking Pin Voltage VSS/TR | TA = +25°C | min -0.3 · max 6 V | 5 |
| Feedback Pin Voltage VFB | TA = +25°C | min -0.3 · max 6 V | 5 |
| Storage Temperature TST | min -65 · max 150 °C | 5 | |
| Junction Temperature TJ | max 150 °C | 5 | |
| Lead Temperature TL | max 260 °C | 5 | |
| Human Body Model HBM | ±2000 V rating | max 2000 V | 5 |
| Charged Device Model CDM | ±500 V rating | max 500 V | 5 |
| Junction to Ambient θJA | V-QFN2030-12 (Type A); FR-4 substrate, four-layer PCB, 2oz copper, minimum recommended pad layout; rating | max 40 °C/W | 5 |
| Junction to Case θJC | V-QFN2030-12 (Type A); FR-4 substrate, four-layer PCB, 2oz copper, minimum recommended pad layout; rating | max 5.5 °C/W | 5 |
| Supply Voltage VIN | TA = +25°C | min 4.5 · max 18 V | 5 |
| Output Voltage VOUT | TA = +25°C | min 0.6 · max 7 V | 5 |
| Operating Ambient Temperature TA | min -40 · max 85 °C | 5 | |
| Operating Junction Temperature TJ | min -40 · max 125 °C | 5 | |
| Shutdown Supply Current ISHDN | VEN = 0V | typ 1 · max 3 uA | 6 |
| Quiescent Supply Current IQ | VFB = 0.85V | typ 360 uA | 6 |
| VIN Power-on Reset Rising Threshold POR | — | min 4 · typ 4.25 · max 4.45 V | 6 |
| VIN Undervoltage Lockout Falling Threshold UVLO | — | typ 3.95 V | 6 |
| VCC Output Voltage VCC | 6.0V < VIN < 18V; 0 < IVCC < 5mA | min 4.75 · typ 5 · max 5.25 V | 6 |
| VCC Current Source IVCC | VIN = 6V, VCC = 0V | max 20 mA | 6 |
| High-Side Power MOSFET On-Resistance (Note 8) RDS(ON)1 | — | typ 36 mΩ | 6 |
| Low-Side Power MOSFET On-Resistance (Note 8) RDS(ON)2 | — | typ 14 mΩ | 6 |
| LS Valley Current Limit (Note 8) IVALLEY_LIMIT | From Source to Drain | min 7.5 · typ 8.5 · max 9.5 A | 6 |
| LS Negative Current Limit INCL | From Drain to Source | typ 2 A | 6 |
| Oscillator Frequency fSW | VFSEL = GND, VOUT = 5V; CCM | typ 400 kHz | 6 |
| Oscillator Frequency fSW | VFSEL = Floating, VOUT = 5V; CCM | typ 800 kHz | 6 |
| Oscillator Frequency fSW | VFSEL = VCC, VOUT = 5V; CCM | typ 1200 kHz | 6 |
| PFM Mode Logic Threshold VMODE_PFM | VMODE = GND | max 0.9 V | 6 |
| Ultrasonic Mode Logic Threshold VMODE_USM | VMODE = Floating | typ 2.5 V | 6 |
| PWM Mode Logic Threshold VMODE_PWM | VMODE = VCC = 5V | min 3.8 V | 6 |
| Minimum On-Time tON_MIN | — | typ 70 ns | 6 |
| Minimum Off-Time tOFF_MIN | — | typ 255 ns | 6 |
| Feedback Voltage VFB | CCM | min 0.594 · typ 0.6 · max 0.606 V | 6 |
| EN Logic High Threshold VEN_H | — | typ 1.2 · max 1.25 V | 6 |
| EN Logic Low Threshold VEN_L | — | min 1.03 · typ 1.12 V | 6 |
| EN Input Current IEN | VEN = 1.5V | typ 5.1 uA | 6 |
| EN Input Current IEN | VEN = 1V | min 1 · typ 1.4 · max 2 uA | 6 |
| Soft-Start Time tSS | VSS/TR = Floating | typ 1 ms | 6 |
| Soft-Start Current Source ISS | VSS/TR = 1.2V | typ 5 uA | 6 |
| Undervoltage Falling Threshold PGUV_FALL | Percent of Output Regulation, Fault | typ 85 % | 6 |
| Undervoltage Rising Threshold PGUV_RISE | Percent of Output Regulation, Good | typ 95 % | 6 |
| Overvoltage Rising Threshold PGOV_RISE | Percent of Output Regulation, Fault | typ 115 % | 6 |
| Overvoltage Falling Threshold PGOV_FALL | Percent of Output Regulation, Good | typ 105 % | 6 |
| Power-Good Rise Delay Time tPG_RD | — | typ 0.5 ms | 6 |
| Power-Good Output Logic Low VPG_OL | IPG = -3mA | max 0.4 V | 6 |
| Thermal Shutdown (Note 8) TSD | — | typ 160 °C | 6 |
| Thermal Shutdown Hysteresis (Note 8) THYS | — | typ 30 °C | 6 |
Pins, by the datasheet
12- 1 PGND
- Power ground; connect to a single point ground and as large a PGND plane as possible for operation and thermal performance. · p. 3
- 2 VIN
- Power input for the IC and converter MOSFETs; drive with 4.5V to 18V and bypass to GND with a suitably large capacitor. · p. 3
- 3 EN
- Enable input; high enables, low disables, and open permits automatic startup; precision threshold supports UVLO programming. · p. 3
- 4 MODE
- Connect to GND for PFM, leave floating for USM, or connect to VCC for PWM Only Mode. · p. 3
- 5 FSEL
- Connect to GND for 400kHz, leave floating for 800kHz, or connect to VCC for 1.2MHz switching frequency. · p. 3
- 6 PG
- Power-good output pulled to GND outside regulation or during soft-start; connect an external pull-up resistor to VCC. · p. 3
- 7 BST
- High-side gate drive boost input; connect a 100nF capacitor to SW to power the high-side driver. · p. 3
- 8 SW
- Power switching output; connect the output LC filter from SW to the output load. · p. 3
- 9 VCC
- Internal supply for logic and gate drivers; place a 1uF capacitor close to VCC and PGND; inactive when EN is low. · p. 3
- 10 SS/TR
- Controls soft-start, tracking, and sequencing; connect a ceramic capacitor to GND to program soft-start or leave floating for internal soft-start. · p. 3
- 11 GND
- Control logic ground; must have a Kelvin connection to PGND. · p. 3
- 12 FB
- Output voltage sensing terminal; connect to the output resistive divider. · p. 3
Questions
Is there a KiCad symbol and footprint for the AP62600SJ?
Yes. The symbol is AP62600SJ-7:AP62600SJ-7 and the footprint Horizon_manufacturer:V-QFN2030-12, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the AP62600SJ?
QFN-12(2x3), with 12 pins. Its footprint is drawn on this page.
Where is the AP62600SJ datasheet?
Diodes Incorporated publishes it: the Datasheet link on this page opens it.
Where can I order the AP62600SJ?
JLCPCB lists it as part C4748917, with 1,597 in stock; the sellers' links on this page open their listings.