Skip to the content

AS5047U-HTSM

Advanced Monolithic SystemsExtended

-40℃~+150℃ 0°~360° 1.2mm 16mA 4.4mm 4.5V~5.5V 5mm Magnetic rotary position sensor No SPI SSOP-14-4.4mm Position Sensors ROHS

Part id
ams/AS5047U-HTSM
Category
Position Sensors
Package
SSOP-14-4.4mm
Pins
14
In stock
13 at JLCPCB (C2153630)
Used on
4 open-source boards

Overview

The AS5047U-HTSM is a position Sensor made by Advanced Monolithic Systems in a SSOP-14-4.4mm package with 14 pins. -40℃~+150℃ 0°~360° 1.2mm 16mA 4.4mm 4.5V~5.5V 5mm Magnetic rotary position sensor No SPI SSOP-14-4.4mm Position Sensors ROHS.

PCBKit's library has its KiCad symbol (EasyEDA_Cloud:AS5147U-HTSM_C38675951, from EasyEDA) and its footprint (EasyEDA_Cloud:SSOP-14_L5.0-W4.4-P0.65-LS6.4-BL, from EasyEDA), ready for a KiCad board. 13 are in stock at JLCPCB (part C2153630). 4 open-source boards in 4 repositories on GitHub use it.

Symbol

1CSn2CLK3MISO4MOSI5TEST6B7A8W/PWM9V10U11VDD12VDD3V313GND14I/PWM
EasyEDA_Cloud:AS5147U-HTSM_C38675951From EasyEDA

Footprint

EasyEDA_Cloud:SSOP-14_L5.0-W4.4-P0.65-LS6.4-BLFrom EasyEDA

From the datasheet

12
Supply, least
4.5 V · VDD, recommended operating minimum, 5.0 V mode · p. 6
Supply, most
5.5 V · VDD, recommended operating maximum, 5.0 V mode · p. 6
Supply, least
3 V · VDD3V3, recommended operating minimum, 3.3 V mode with NOISESET set · p. 6
Supply, most
3.6 V · VDD3V3, recommended operating maximum, 3.3 V mode with NOISESET set · p. 6
Supply, absolute maximum
7 V · VDD, absolute maximum · p. 5
Supply, absolute maximum
5 V · VDD3V3, absolute maximum · p. 5
Works from
-40 °C · Ambient operating minimum · p. 5
Works up to
150 °C · Ambient operating maximum · p. 5
Works up to
125 °C · Ambient operating maximum, 3.3 V mode, NOISESET = 0 · p. 11
Takes working
16 mA · VDD supply current, max · p. 6
A pin gives at most
4 mA · Digital output current, max, 5 V operation · p. 6
A pin gives at most
2 mA · Digital output current, max, 3 V operation · p. 6

What it is and has

7
Interfaces
Independent SPI, ABI, UVW and PWM outputs · p. 1
Magnetic stray field immunity
Integrated · p. 1
Dynamic angle error compensation
DAEC · p. 1
Dynamic filter system
DFS · p. 1
SPI resolution
14 bit · p. 7
Maximum rotational speed
28000 rpm · p. 8
Package
TSSOP14 · p. 46

Around it

4
cap 1μF
between VDD3V3 and GND; LDO decoupling capacitor; locate close to the chip. · p. 11
cap 100nF
between VDD and GND; Supply capacitor shown for 5.0 V and 3.3 V operation in Figure 11. · p. 11
res unspecified
between CSn and supply; Pull-up required if SPI is unused. · p. 4
res unspecified
between CLK and GND; Pull-down required if SPI is unused. · p. 4

Specifications

41
ParameterConditionsAs printedPage
DC Supply Voltage at VDD pin VDD5Not operationalmin -0.3 · max 7 V5
DC Supply Voltage at VDD3V3 pin VDD3Not operationalmin -0.3 · max 5 V5
DC Supply Voltage at GND pin VSSmin -0.3 · max 0.3 V5
Input Current (latch-up immunity) IscrAEC-Q100-004min -100 · max 100 mA5
Total Power Dissipation (all supplies and outputs) PTmax 150 mW5
Electrostatic Discharge HBM ESDHBMAEC-Q100-002; rating ±2 kVmax 2 kV5
Operating Temperature Range TAMBAmbient temperaturemin -40 · max 150 °C5
Programming Temperature TaProgProgramming @ room temperature (25°C ± 20°C)min 5 · max 45 °C5
Storage Temperature Range TSTRGmin -55 · max 150 °C5
Package Body Temperature TBODYIPC/JEDEC J-STD-020max 260 °C5
Relative Humidity (non-condensing) RHNCmin 5 · max 85 %5
Positive supply voltage VDD55.0V operation modemin 4.5 · typ 5 · max 5.5 V6
Positive supply voltage VDD3V33.3V operation mode; from -40°C to 150°C (NOISESET bit has to set)min 3 · typ 3.3 · max 3.6 V6
Positive supply voltage VDD_BurnSupply voltage required for programming in 3.3V operationmin 3.3 · max 3.5 V6
Regulated voltage VREGVoltage at VDD3V3 pin if VDD ≠ VDD3V3min 3.2 · typ 3.4 · max 3.6 V6
Supply current IDDmax 16 mA6
C_L C_Lmax 50 pF6
Output current 5 V operation(1) I_Out_5VOnly applicable for digital output pins I/PWM, A, B, U, V, W/PWM, MISO.max 4 mA6
Output current 3 V operation(1) I_Out_3VOnly applicable for digital output pins I/PWM, A, B, U, V, W/PWM, MISO.max 2 mA6
Orthogonal Magnetic Field Strength BzRequired orthogonal component of the magnetic field strength measured at the package surface along a circle of 1.1mmmin 35 · max 70 mT7
Core and resolution on SPI REStyp 14 bit7
Resolution of the ABI interface RES_ABIProgrammable with register setting (ABIRES)min 25 · max 4096 steps7
Non-linearity, optimum placement of the magnet INLOPT @ 25°C25°C; values are ±typ 0.4 · max 0.8 degree7
Non-linearity, optimum placement of magnet and temperature -40°C to 150°C INLOPT+TEMPValues are ±typ 0.6 · max 1 degree7
Non-linearity @ displacement of magnet and temperature -40°C to 150°C INLDIS+TEMPAssuming N35H Magnet (D=8mm, H=3mm), 500um displacement in x and y, z-distance = 2000um; maximum is ±1.2max 1.2 degree7
RMS output noise without filter (1 sigma) on SPI, ABI, PWM and UVW. Not tested, guaranteed by design ONLOrthogonal component for the magnetic field within the specified range (Bz), NOISESET= 0typ 0.034 · max 0.068 degree7
RMS output noise without filter (1 sigma) on SPI, ABI, PWM and UVW. Not tested, guaranteed by design ONHOrthogonal component for the magnetic field within the specified range (Bz), NOISESET = 1typ 0.041 · max 0.082 degree7
System propagation delay –core tdelayReading angle via SPImin 90 · max 110 us7
Residual system propagation delay after dynamic angle error correction tdelay_DAECAt ABI, UVW and SPImin -1.9 · max 1.9 us8
Refresh time of DAEC output trefreshRefresh time at SPI(ANGLECOM), ABI, UVWmin 202 · typ 222 · max 247 ns8
Dynamic angle error DAE1700At 1700 rpm constant speedmax 0.02 degree8
Dynamic angle error DAEmaxAt 28000 rpm constant speedmax 0.32 degree8
Maximum speed MSmax 28000 rpm8
Power-on time tponGuaranteed by design. Time between VDD > VDDmin and the first valid outcomemax 10 ms9
Temperature RangeVDD = 5.0 V; NOISESET = 0min -40 · max 150 °C11
Temperature RangeVDD = 3.3 V; NOISESET = 0min -40 · max 125 °C11
Temperature RangeVDD = 3.3 V; NOISESET = 1min -40 · max 150 °C11
Programming temperature TaProgProgramming @ Room Temperature (25°C ± 20°C)min 5 · max 45 °C39
Positive supply voltage VDD5 V operation mode. Supply voltage during programmingmin 4.5 · typ 5 · max 5.5 V39
Positive supply voltage VDD3.3 V operation mode. Supply voltage during programmingmin 3.3 · max 3.5 V39
Current for programming IProgMax current during OTP burn procedure.max 100 mA39

Pins, by the datasheet

14
1 CSn
SPI chip select, active low; pull up if SPI is unused. · p. 3
2 CLK
SPI clock; pull down if SPI is unused. · p. 3
3 MISO
SPI master data input, slave output; may be left open if SPI is unused. · p. 3
4 MOSI
SPI master data output, slave input; pull down if SPI is unused. · p. 3
5 TEST
Test pin; connect to ground. · p. 3
6 B
Incremental signal B; may be left open if unused. · p. 3
7 A
Incremental signal A; may be left open if unused. · p. 3
8 W/PWM
Commutation signal W or PWM-encoded output; may be left open if unused. · p. 3
9 V
Commutation signal V; may be left open if unused. · p. 3
10 U
Commutation signal U; may be left open if unused. · p. 3
11 VDD
5V power supply voltage for on-chip regulator. · p. 3
12 VDD3V3
3.3V on-chip LDO output; requires an external 1uF decoupling capacitor. · p. 4
13 GND
Ground. · p. 4
14 I/PWM
Incremental signal I (index) or PWM; may be left open if unused. · p. 4

Ordering codes, by the datasheet

2
AS5047U-HTSM
TSSOP14 · 7” Tape & Reel in dry pack; 500 pcs/reel · p. 46
AS5047U-HTST
TSSOP14 · 13” Tape & Reel in dry pack; 4500 pcs/reel · p. 46

Open-source boards using it

4
  • 2 layers54.8 × 54 mmFoc encoder, the printed circuit board in 3D

    Foc encoder

    Gepetto/MC300A_AS5047_encoder_PCB

    This is a PCB support for a AS5047 magnetic encoder to replace MC300 control board on myactuator RMD-X actuators.

    28 parts1BSD-2-Clause
  • 2 layers19.4 × 30.2 mmEncoder, the printed circuit board in 3D

    Encoder

    LucienMorey/uni-work

    A collation of my software related work and assignments while at University of Technology Sydney.

    13 partsMIT
  • 4 layers47 × 48.5 mmCubeSat Encoder, the printed circuit board in 3D

    CubeSat Encoder

    famesy/CuteSat

    This is an open-source CubeSat printed circuit board (PCB) project that includes both hardware and software components.

    26 parts3
  • 2 layers9.6 × 14.1 mmEncoder, the printed circuit board in 3D

    Encoder

    Team-Micras/MicrasPCB

    Micras micromouse PCBs as code: Zener circuits, KiCad layouts, CI checks and a design portal

    3 parts1

Questions

Is there a KiCad symbol and footprint for the AS5047U-HTSM?

Yes. The symbol is EasyEDA_Cloud:AS5147U-HTSM_C38675951 and the footprint EasyEDA_Cloud:SSOP-14_L5.0-W4.4-P0.65-LS6.4-BL, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the AS5047U-HTSM?

SSOP-14-4.4mm, with 14 pins. Its footprint is drawn on this page.

Where is the AS5047U-HTSM datasheet?

Advanced Monolithic Systems publishes it: the Datasheet link on this page opens it.

Where can I order the AS5047U-HTSM?

JLCPCB lists it as part C2153630, with 13 in stock; the sellers' links on this page open their listings.

Which open-source boards use the AS5047U-HTSM?

4 boards in 4 repositories on GitHub; the most starred are listed on this page, with their KiCad files.