

- Size
- 50 × 50 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 73
- Nets
- 64
- Pads
- 314
- Tracks, vias
- 901, 136
- Pours
- 3
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 31 Jul 2025
- Updated
- 13 Nov 2025
Overview
Probe is an open-source printed circuit board by zuhayrl, from the zuhayrl/EEE4022S_Thesis repository on GitHub. It is a 4-layer board of 50 × 50 mm with 73 parts on 64 nets, routed with 901 tracks and 136 vias.
It is built around the ESP32-S2-MINI-1-N4, LM358 and LPS28DFW, with the AMS1117-3.3, AMS1117-5.0 and SP3485EN-Y among its other parts. Its parts include 26 resistors, 23 capacitors, 12 ICs, 8 connectors and 2 diodes. It belongs with the sensors and measurement boards and the ESP32 boards of this library.
Main components
7ESP32-S2-MINI-1-N4
SMD-65P-40℃~+85℃ -97dBm 19.5dBm 2.4GHz 310mA 3V~3.6V 63mA ESP32-S2FH4 Chip On-board PCB Antenna Support USB interface UART、SPI、I2C、I2S、USB SMD-65P WiFi Modules ROHSEspressif SystemsWiFi ModulesLM358
SOP-8-18V~18V 0℃~+70℃ 1.2MHz 10nA 2 24mA 3V~36V 500uA 50nA 5mV 80dB Built-in compensation SOP-8 Operational Amplifier ROHSMSKSEMIOperational AmplifierLPS28DFW
CCLGA-7(2.8x2.8)-40℃~+85℃ 0.015hpa 0.5hpa 1.7V~3.6V 26Kpa~4.06bar 900nA I2C、I3C CCLGA-7(2.8x2.8) Pressure Sensors ROHSSTMicroelectronicsPressure SensorsAMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsAMS1117-5.0
SOT-223-40℃~+125℃ 1 1.3V 15V 1A 5V 60dB Fixed Positive Short Circuit Protection、Thermal shutdown SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsSP3485EN-Y
SOP-8SOP-8 RS-485 / RS-422 ICs ROHSYLPTECRS-485 / RS-422 ICsSS34
SMA(DO-214AC)-55℃~+125℃ 3A 40V 500uA@40V 550mV@3A Independent SMA(DO-214AC) Schottky Diodes ROHSMDDSchottky Diodes
README
README.mdEEE4022S_Thesis
Parts
73| Qty | Value | Footprint | References |
|---|---|---|---|
| 15 | 0.1uF | Capacitor_SMD:C_0402_1005Metric | C1, C3, C5, C8, C13, C14, C15, C16, C17, C18, C19, C20, C21, C22, C23 |
| 6 | 22uF | Capacitor_SMD:C_1206_3216Metric | C2, C4, C6, C7, C9, C10 |
| 5 | 4.7K | Resistor_SMD:R_0603_1608Metric | R24, R25, R26, R27, R28 |
| 4 | 20 | Resistor_SMD:R_0603_1608Metric | R17, R18, R19, R20 |
| 4 | 4xSwitch | Package_SO:TSSOP-14_4.4x5mm_P0.65mm | U6, U7, U8, U10 |
| 3 | 10K | Resistor_SMD:R_0603_1608Metric | R6, R7, R22 |
| 3 | 300 | Resistor_SMD:R_0603_1608Metric | R8, R9, R10 |
| 3 | 30K | Resistor_SMD:R_0603_1608Metric | R14, R15, R16 |
| 3 | 3K | Resistor_SMD:R_0603_1608Metric | R11, R12, R13 |
| 2 | 10uF | Capacitor_SMD:C_0603_1608Metric | C11, C12 |
| 2 | 1K | Resistor_SMD:R_0603_1608Metric | R5, R21 |
| 2 | 470 | Resistor_SMD:R_0603_1608Metric | R1, R2 |
| 2 | LM358 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U5, U9 |
| 1 | 120 | Resistor_SMD:R_0603_1608Metric | R23 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U2 |
| 1 | AMS1117-5.0 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U3 |
| 1 | Au1 | ThesisLib:Au_Electrode | J7 |
| 1 | Au2 | ThesisLib:Au_Electrode | J8 |
| 1 | Data | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J5 |
| 1 | ESP32-S2-MINI-1 | PCM_Espressif:ESP32-S2-MINI-1 | U4 |
| 1 | Inter Board | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J6 |
| 1 | LED | LED_SMD:LED_0603_1608Metric | D4 |
| 1 | LPS28DFW | ThesisLib:CCLGA-7L | U13 |
| 1 | MCP4725xxx-xCH | Package_TO_SOT_SMD:SOT-23-6 | U1 |
| 1 | PWR | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J1 |
| 1 | SP3485EN | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U12 |
| 1 | SS34 | Diode_SMD:D_SMA | D1 |
| 1 | SW_Boot | ThesisLib:SW_TS-1088-AR02016 | SW2 |
| 1 | SW_En | ThesisLib:SW_TS-1088-AR02016 | SW1 |
| 1 | TP | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J3 |
| 1 | Temp_Screw | ThesisLib:3-Wire Solder Pads | J4 |
| 1 | USB_B_Micro | ThesisLib:SHOUHAN_MICROXNJ_Edited | J2 |
More from zuhayrl/EEE4022S_Thesis
5- 4 layers50 × 50 mm

- 2 layers50 × 75 mm

- 2 layers55 × 70 mm

- 2 layers28 × 40 mm

- 2 layers28 × 45.6 mm

Similar boards
- 2 layers

Steuerplatine
tomatenkuchen/coffeepress-pressure-control
esp32 based steam pressure control embedded system for la pavoni europiccola
61 partsGPL-3.0 - 2 layers25.4 × 17.8 mm

Lps28dfwBreakoutBoard
DeepSpace00/Awohali
An open soure GNSS station for flash flood nowcasting
12 parts - 2 layers140 × 140 mm

- 2 layers200 × 200 mm

- 4 layers54 × 106 mm

- 2 layers31.2 × 45.8 mm

Esp32-homeassistant rf bridge
grimsteel/homeassistant-rf-bridge
MQTT-based Home Assistant RF + IR bridge
47 parts1GPL-3.0 - 2 layers85.1 × 119.9 mm

- 2 layers30 × 51 mm

WasteIndicator
FunDeckHermit/WasteIndicator
Scripts that modify Tasmota to interact with the Ximmio waste API
16 partsMIT
Questions
How big is the Probe PCB?
It measures 50 × 50 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Probe use?
73 parts, built around the ESP32-S2-MINI-1-N4, LM358, LPS28DFW and AMS1117-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Probe KiCad files?
From the zuhayrl/EEE4022S_Thesis repository on GitHub, at the commit this page was made from: the board is PCB/Probe/probe_v2-0/probe.kicad_pcb and its schematic Diagrams/report_diagrams/report_diagrams.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Probe design in my own project?
Its repository states no licence, so its author keeps all rights: ask zuhayrl before reusing the design.