4 layers70 × 70 mm
Ai camera
maxlab-io/tokay-lite-pcb
Tokay AI Camera - ESP32 camera development board
161 parts130CERN-OHL-P-2.0
2 layers18 × 28 mm
ESP ISP
ZDBioHazard/ESP-ISPA UART programming jig for ESP-12 modules using pogo-pins.
- Size
- 18 × 28 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 28
- Nets
- 17
- Pads
- 64
- Tracks, vias
- 108, 12
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 29 Sep 2016
- Updated
- 13 Mar 2017
Overview
ESP ISP is an open-source printed circuit board by ZDBioHazard, from the ZDBioHazard/ESP-ISP repository on GitHub. It is a 2-layer board of 18 × 28 mm with 28 parts on 17 nets, routed with 108 tracks and 12 vias.
It is built around the XC6206-2.8V. Its parts include 11 resistors, 5 diodes, 3 capacitors, 2 ICs and 2 transistors. It belongs with the ESP8266 boards of this library.
Main components
1README
README.mdESP-ISP
This is just a simple programming jig for the ESP-12 module.
When putting this device together, use <=40-mil pogo pins for the ESP pins. You can then place this device on top of a ESP-12 unit to access it's serial port. (Be careful not to short any of the pogo pins on the metal can though. It can be tricky!)
P1is normal FTDI header. 5V should work.SW1is a reset switch. Hold it down for >5s to bringGPIO0low and release to start flash mode.D5should light up whenGPIO0is low.D3is a power indicator.D2should light up when the ESP is receiving serial data.
Check the schematic for the parts list.
Parts
28| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 10K | Resistors_SMD:R_0805 | R1, R2, R3, R4, R5, R6 |
| 3 | 220 | Resistors_SMD:R_0805 | R9, R10, R11 |
| 2 | 1M | Resistors_SMD:R_0805 | R7, R8 |
| 2 | 1N5819 | Diodes_SMD:DO-214BA | D1, D2 |
| 2 | 1uF | Capacitors_SMD:C_0805 | C1, C2 |
| 2 | 2N7002 | TO_SOT_Packages_SMD:SOT-23 | Q1, Q2 |
| 2 | GREEN | LEDs:LED_1206 | D3, D4 |
| 1 | 2.2uF | Capacitors_SMD:C_0805 | C3 |
| 1 | DUCK | my_footprints:DUCK | G*** |
| 1 | ESP-12 | my_footprints:ESP-12-ISP | U1 |
| 1 | FTDI_BASIC | my_footprints:Pin_Header_Simple_1x06 | P1 |
| 1 | LOGO | my_footprints:Ferret_Logo_0.1in | G*** |
| 1 | LOGO | my_footprints:OSHW_Logo_0.1in | G*** |
| 1 | RED | LEDs:LED_1206 | D5 |
| 1 | RESET | my_footprints:SMD_PUSHBUTTON_3.6x6.0mm | SW1 |
| 1 | XC6206 | TO_SOT_Packages_SMD:SOT-23 | U2 |
Questions
How big is the ESP ISP PCB?
It measures 18 × 28 mm and has 2 copper layers, 1.6 mm thick.
What parts does the ESP ISP use?
28 parts, built around the XC6206-2.8V. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ESP ISP KiCad files?
From the ZDBioHazard/ESP-ISP repository on GitHub, at the commit this page was made from: the board is espisp.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the ESP ISP design in my own project?
Its repository states no licence, so its author keeps all rights: ask ZDBioHazard before reusing the design.
Similar boards
- 2 layers229.8 × 102.6 mm
- 2 layers17.4 × 60.6 mm
- 4 layers40.1 × 39.8 mm
Stm32g431-mt6701-stspin233
VIPQualityPost/aioli-foc
Small, simple closed loop BLDC driver implementing SimpleFOC
90 parts37 - 2 layers185.3 × 68 mm
- 2 layers253.3 × 113.3 mm
- 2 layers344.7 × 123.6 mm
- 2 layers288.8 × 160.1 mm
GRAM SLIM
GRAMCTRL/GRAM-SLIM
Open source low-profile leverless design with an integrated RP2040.
64 parts24GPL-3.0