

E Bike
Ebike PAS controller
- Size
- 95 × 78 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 71
- Nets
- 42
- Pads
- 188
- Tracks, vias
- 250, 36
- Pours
- 6
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 19 Jun 2021
- Updated
- 29 Jun 2025
Overview
E Bike is an open-source printed circuit board by zachleedogg, from the zachleedogg/E_Bike repository on GitHub, published under the CC0-1.0 licence. It is a 2-layer board of 95 × 78 mm with 71 parts on 42 nets, routed with 250 tracks and 36 vias.
It is built around the ATTINY167-XU, INA240A3D and MAX17552AUB+, with the TPS7B6950QDBVRQ1, CX3225CA16000H0HSSCC and PESD2USB5UX-TR among its other parts. Its parts include 30 capacitors, 27 resistors, 7 connectors, 4 ICs and 1 diode. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
7ATTINY167-XU
TSSOP-20-40℃~+85℃ 1.8V~5.5V 10bit 16 16KB 16MHz 512Byte 512Byte 8 Bit AVR Built-in FLASH TSSOP-20 Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)INA240A3D
SOIC-8-40℃~+125℃ -4V~80V 1 1.8mA 100V/V 132dB 2.7V~5.5V 250nV/℃ 2V/us 400kHz 40nV/√Hz@1kHz 5uV 90uA Bidirectional detection、Zero drift / auto-zero、Programmable output reference level、Analog output interface ±80V SOIC-8 Current Sense Amplifiers ROHSTexas InstrumentsCurrent Sense AmplifiersMAX17552AUB+
MSOP-10-40℃~+125℃@(TA) 1 100kHz~2.2MHz 100mA 22uA 4V~60V 800mV~54V Adjustable Buck Built-in Overcurrent Protection、Light load efficient mode、Adjustable soft-start、Operating status indication、Frequency synchronization、Hiccup current limiting Step-down type Yes MSOP-10 DC-DC Converters ROHSMaxim Integrated (Analog Devices)DC-DC ConvertersTPS7B6950QDBVRQ1
SOT-23-5-40℃~+150℃@(Tj) 1 150mA 15uA 40V 450mV@(100mA) 5V 60dB@(100Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal Shutdown、Enable control、Input undervoltage protection Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsCX3225CA16000H0HSSCC
SMD3225-4P-40℃~+125℃ 100Ω 12pF 16MHz ±20ppm ±50ppm SMD3225-4P Crystals ROHSKyocera AVXCrystalsPESD2USB5UX-TR
TO-236AB0.47pF 11V 1nA 3.3V 4A@8/20us 5V TVS Unidirectional TO-236AB ESD and Surge Protection (TVS/ESD) ROHSNexperiaESD And Surge Protection (TVS/ESD)U500
-Switch Accessories / CapsAPEM
README
README.mdE_Bike
Ebike PAS controller
Parts
71| Qty | Value | Footprint | References |
|---|---|---|---|
| 19 | 10k | Capacitor_SMD:C_0603_1608Metric | R5, R6, R10, R11, R12, R13, R14, R15, R16, R19, R22, R23, R24, R25, R26, R27 +3 |
| 14 | 10n | Capacitor_SMD:C_0603_1608Metric | C1, C8, C10, C11, C12, C15, C16, C17, C18, C19, C20, C21, C28, C29 |
| 6 | 1u | Capacitor_SMD:C_0603_1608Metric | C7, C13, C14, C22, C23, C30 |
| 5 | 100n | Capacitor_SMD:C_0603_1608Metric | C3, C4, C6, C9, C27 |
| 3 | Conn_01x03 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J3, J4, J6 |
| 2 | 18p | Capacitor_SMD:C_0603_1608Metric | C24, C25 |
| 2 | 22R0 | Capacitor_SMD:C_0603_1608Metric | R17, R18 |
| 2 | Screw_Terminal_01x01 | MountingHole:MountingHole_4.3mm_M4_DIN965_Pad | J5, J8 |
| 1 | 10u | Capacitor_SMD:C_1206_3216Metric | C5 |
| 1 | 150u | Inductor_SMD:L_Bourns-SRN4018 | L1 |
| 1 | 1u | Capacitor_SMD:C_1206_3216Metric | C2 |
| 1 | 220n | Capacitor_SMD:C_0603_1608Metric | C26 |
| 1 | 22R1 | Capacitor_SMD:C_0603_1608Metric | R20 |
| 1 | 49k9 | Capacitor_SMD:C_0603_1608Metric | R4 |
| 1 | 4R7 | Capacitor_SMD:C_0603_1608Metric | R21 |
| 1 | 576k | Capacitor_SMD:C_0603_1608Metric | R3 |
| 1 | 69k8 | Capacitor_SMD:C_0603_1608Metric | R1 |
| 1 | ATtiny167-X | Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm | U5 |
| 1 | AVR-ISP-6 | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | J1 |
| 1 | CX3225CA16000H0HSSCC | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | Conn_01x05 | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J2 |
| 1 | INA240A3D | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U2 |
| 1 | MAX17552AUB+ | Package_SO:MSOP-10_3x3mm_P0.5mm | U1 |
| 1 | PESD2USB5UX-TR | Package_TO_SOT_SMD:TSOT-23 | D1 |
| 1 | TPS7B6950QDBVRQ1 | Package_TO_SOT_SMD:SOT-23-5 | U3 |
| 1 | u500 | Resistor_SMD:R_1206_3216Metric | R2 |
More from zachleedogg/E_Bike
2- 2 layers36.3 × 26.5 mm

- 2 layers36.3 × 24.5 mm

Similar boards
- 4 layers220 × 100 mm

- 6 layers100 × 220 mm

- 2 layers35 × 24 mm

HyperLink
antsouchlos/hyperlink-hw
A PCB for gathering data form CommonSense boards over bluetooth and retransmitting over wifi
46 partsMIT - 4 layers150 × 115 mm

Usb controlled debug hub 2a
misko/prompt2device
The separate vNext PCB skill and orchestrator package is available alongside the reference workflow below; existing projects keep their accepted toolchain until an explicit migration.
190 parts3MIT - 4 layers130 × 90 mm

Phase2-module
udaravima/Lab_Bench
A modular, rack-style DC power supply: up to 8 hot-pluggable 600 W buck modules on a shared DC input bus, coordinated by a central manager over CAN.
180 parts1GPL-3.0 - 4 layers113 × 65.6 mm

- 4 layers127.5 × 145 mm

SkidSteer PCB
raitzjm/SkidSteer_PCB
PCB for skid steer spraying rover project for KSU Precision Ag Lab
153 parts - 4 layers282 × 112 mm

Vfd
SimonSchaeff/variable-frequency-drive-induction-motor
This repository contains the hardware and software design files for a frequency inverter for asynchronous motors up to 3 kW, developed as part of a university project at Munich University of Applied Sciences.
117 parts
Questions
How big is the E Bike PCB?
It measures 95 × 78 mm and has 2 copper layers, 1.6 mm thick.
What parts does the E Bike use?
71 parts, built around the ATTINY167-XU, INA240A3D, MAX17552AUB+ and TPS7B6950QDBVRQ1. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the E Bike KiCad files?
From the zachleedogg/E_Bike repository on GitHub, at the commit this page was made from: the board is Hardware/E-Bike_V3/E-Bike.kicad_pcb and its schematic Hardware/E-Bike_V2/E-Bike.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the E Bike design in my own project?
Its repository publishes it under the CC0-1.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).