Skip to the content
2 layers11.5 × 16.5 mmENCODER, the printed circuit board in 3D

This PCB is developed for RoboCup Junior Soccer

Size
11.5 × 16.5 mm
Copper layers
2
Thickness
1.6 mm
Parts
12
Nets
10
Pads
48
Tracks, vias
96, 7
Pours
2
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
25 Feb 2023
Updated
25 Feb 2023

Overview

ENCODER is an open-source printed circuit board by yutatech, from the yutatech/TANUKICHI_2021-PCB repository on GitHub, published under the MIT licence. It is a 2-layer board of 11.5 × 16.5 mm with 12 parts on 10 nets, routed with 96 tracks and 7 vias.

It is built around the ATTINY84A-MMH. Its parts include 4 ICs, 3 resistors, 2 capacitors, 2 connectors and 1 transistor. It belongs with the AVR (ATmega, ATtiny) boards of this library.

Main components

1

README

README.md

TANUKICHI_2021-PCB

This PCB is developed for RoboCup Junior Soccer. The robot has competed as "CAIO Tezukayama" in 2019 and "Leopard" in 2021.

Related Web sites

Related Repositories

Related Resources

TDP
Video

Awards

  • ロボカップジュニア日本大会2021オンライン (RoboCup Junior Japan Tournament 2021 Online)
    • サッカーオープン 優勝 (SoccerOpen 1st Place)
    • ベストプレゼンビデオ賞 (Best Presentation Video Award)
    • ベストインタビュー賞 (Best Interview Award)
    • ベストビジュアルポスター賞 (Best Visual Poster Award)
  • RoboCup 2021 WORLDWIDE
    • SoccerOpen Indvidual 1st Place
    • SoccerOpen SuperTeam 1st Place

Environment

These files are edited with KiCAD 5.1.5

PCB design files

  • MAIN
    • This PCB is the main board of the robot.
  • MOTOR
    • This PCB drives 4 motors and 2 kickers. It is connected to MAIN with pin headers.
  • LINE
    • This PCB includes 2 types of line sensor boards. The robot has two sensor boards of each type.
  • TOP
    • This PCB distributes the wiring from MAIN to the devices mounted on top of the robot.
  • BOTTOM
    • This PCB is connected to the line sensor board without using cables.
  • BOOST V1
    • This PCB is a boost circuit for kickers. It outputs 60V. This version is installed to the robot because it is stable and works well.
  • BOOST V2
    • This PCB is also a boost circuit for kickers. It outputs 150V. This version is an improvement on V1, but was not adopted because it would have caused noise in the surrounding circuit.
  • ENCODER
    • This PCB is a magnetic pulse encoder board.
  • PROTECTION
    • This PCB is Li-PO Battery protection circuit. The voltage of each cell is not monitored, so any imitation should be done at your own risk.

Parts

12
QtyValueFootprintReferences
210Kmodule:1005R29, R30
21umodule:1005C32, C33
2AH1751module:Q_SOT-23U12, U13
14.7Kmodule:1005R28
1AP7333module:Q_SOT-23U11
1ATtiny84A-MMHmodule:QFN-20_P0.45U14
1Conn_01x02module:2PadsJ11
1Conn_01x05module:CONN_01x05J5
1Q_Photo_NPNmodule:2PadsQ24

More from yutatech/TANUKICHI_2021-PCB

8
  • 2 layers60 × 60 mmTANUKICHI 2021-PCB, the printed circuit board in 3D

    TANUKICHI 2021-PCB

    yutatech/TANUKICHI_2021-PCB

    This PCB is developed for RoboCup Junior Soccer

    83 parts5MIT
  • 2 layers60 × 60 mmMOTOR, the printed circuit board in 3D

    MOTOR

    yutatech/TANUKICHI_2021-PCB

    This PCB is developed for RoboCup Junior Soccer

    69 parts5MIT
  • 2 layers70 × 97.7 mmLINE, the printed circuit board in 3D

    LINE

    yutatech/TANUKICHI_2021-PCB

    This PCB is developed for RoboCup Junior Soccer

    60 parts5MIT
  • 2 layers41 × 42 mmBOOST, the printed circuit board in 3D

    BOOST

    yutatech/TANUKICHI_2021-PCB

    This PCB is developed for RoboCup Junior Soccer

    50 parts5MIT
  • 2 layers41 × 42 mmBOOST, the printed circuit board in 3D

    BOOST

    yutatech/TANUKICHI_2021-PCB

    This PCB is developed for RoboCup Junior Soccer

    30 parts5MIT
  • 2 layers28 × 26.5 mmPROTECTION, the printed circuit board in 3D

    PROTECTION

    yutatech/TANUKICHI_2021-PCB

    This PCB is developed for RoboCup Junior Soccer

    28 parts5MIT
  • 2 layers38.1 × 61.1 mmTOP, the printed circuit board in 3D

    TOP

    yutatech/TANUKICHI_2021-PCB

    This PCB is developed for RoboCup Junior Soccer

    22 parts5MIT
  • 2 layers56.3 × 60.8 mmBOTTOM, the printed circuit board in 3D

    BOTTOM

    yutatech/TANUKICHI_2021-PCB

    This PCB is developed for RoboCup Junior Soccer

    17 parts5MIT

Similar boards

  • 2 layersAmulet, the printed circuit board in 3D

    Amulet

    mitxela/amulet

    Source code and KiCad design files for the UV Protection Amulet.

    31 parts42
  • 2 layers35 × 43 mmOc DevKit2, the printed circuit board in 3D

    Oc DevKit2

    SuperMechaCow/OpenCritter

    An open source digital pet

    40 parts20MIT
  • 2 layersNrf bga, the printed circuit board in 3D

    Nrf bga

    github-linguist/linguist

    Language Savant. If your repository's language is being reported incorrectly, send us a pull request!

    12 parts14kMIT
  • 2 layers66.9 × 74.5 mmDeskHop, the printed circuit board in 3D

    DeskHop

    hrvach/deskhop

    Fast Desktop Switching Device

    12 parts7.9kGPL-3.0
  • 2 layers40 × 15 mmSensors, the printed circuit board in 3D

    Sensors

    google/mozc-devices

    Circuit diagrams and firmware source code for Gboard DIY keyboards

    12 parts3kApache-2.0
  • 2 layers42.7 × 56.5 mmTle6240 driver, the printed circuit board in 3D

    Tle6240 driver

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    12 parts1.2k
  • 2 layers49 × 25 mm5v boost regulator, the printed circuit board in 3D

    5v boost regulator

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    12 parts915

Questions

How big is the ENCODER PCB?

It measures 11.5 × 16.5 mm and has 2 copper layers, 1.6 mm thick.

What parts does the ENCODER use?

12 parts, built around the ATTINY84A-MMH. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the ENCODER KiCad files?

From the yutatech/TANUKICHI_2021-PCB repository on GitHub, at the commit this page was made from: the board is ENCODER/ENCODER.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the ENCODER design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).