
Delta 2.0
YesidAlmanzaGamba/Thesis-Flight-Controller-Fixed-Wing
This thesis addresses the critical need for efficient data management and operational control in fixed-wing UAVs, targeting the gaps in current commercial flight controllers.

This thesis addresses the critical need for efficient data management and operational control in fixed-wing UAVs, targeting the gaps in current commercial flight controllers.
DELTA 1.0 is an open-source printed circuit board by YesidAlmanzaGamba, from the YesidAlmanzaGamba/Thesis-Flight-Controller-Fixed-Wing repository on GitHub. It is a 2-layer board of 156.4 × 71.6 mm with 39 parts on 54 nets, routed with 339 tracks and 26 vias.
It is built around the V7805-1000, PCA9685PW and BNO055, with the XT60-M among its other parts. Its parts include 10 connectors, 4 resistors, 4 diodes, 3 capacitors and 2 ICs. It belongs with the ESP32 boards of this library.
Bachelor's thesis (Proyecto de Grado), Electronic Engineering, Universidad de los Andes Author: Yesid Camilo Almanza Gamba · Advisor: Prof. Alba Ávila Bernal
📄 Read the full thesis (PDF, Spanish) · 🎥 Watch the project video
This project covers the design, build and flight testing of a custom flight controller for fixed-wing UAVs based on the ESP32-S3 (replacing the usual STM32 architecture), along with a desktop ground control station (GCS) that shows telemetry in real time and reconstructs the flight path from GPS and altitude data.
┌───────────────── Aircraft ─────────────────┐ ┌──────────── Ground ────────────┐
│ IMU / Baro / Airspeed / GPS ──► ESP32-S3 │ nRF24L01 │ ESP32-S3 receiver ──USB/serial─┼─► PyQt5 GCS
│ FlySky RX (iBus/PPM) ──────────► │ │ ─────────► │ (src/recepcion.cpp) │ (src/interfazWave)
│ PCA9685 ◄─┘──► SD │ └────────────────────────────────┘
│ servos / ESC │
└────────────────────────────────────────────┘| Path | Contents |
|---|---|
src/ | Firmware (C++/Arduino, PlatformIO) |
src/sensorica/ | Sensor drivers and fusion (IMU, barometer, airspeed, GPS) |
src/control/ | Servo / control-surface regulation (ReguladorServos) |
src/navegacion/ | Control loop and waypoint navigation |
src/telemetria/ | FlySky receiver handling |
src/utilities/ | OLED display helper |
src/main.txt | Onboard flight-controller program (see Building the firmware) |
src/recepcion.cpp | Ground receiver program (nRF24 → serial / SD) |
src/archivosDePrueba/ | Standalone test sketches for individual sensors |
src/interfazWave/ | Ground control station (Python / PyQt5) |
test/graphs_files/ | Post-flight analysis and plotting scripts |
flight_tests/ | Raw flight logs (CSV/JSON), generated plots and HTML maps |
PCB/ | KiCad projects (Delta 1.0, Delta 2.0), footprints, symbols, 3D models and fabrication outputs |
Documento/ | LaTeX source of the thesis plus the compiled PDF |
Requirements: PlatformIO (VS Code extension or CLI). Library dependencies are listed in platformio.ini and download automatically on the first build.
PlatformIO compiles every .cpp file in src/, so only one program with setup()/loop() can be active at a time. The inactive ones are stored as .txt:
src/recepcion.cpp is active.src/recepcion.cpp → recepcion.txt and src/main.txt → main.cpp.# set upload_port in platformio.ini to your board's port first (COM10 by default)
pio run -t upload
pio device monitor # 115200 baudRequirements: Python 3.9+.
cd src/interfazWave
pip install -r requirements.txt
python main.py # pick the receiver's serial port, then the main window opensRun it from inside
src/interfazWave/, because the app loads images and saves data (datosGuardados/) through relative paths.
The scripts in test/graphs_files/ read the CSV logs in flight_tests/ and generate the plots and Folium maps stored there. They use pandas, matplotlib, numpy, scipy and folium.
The thesis (in Spanish, with an English abstract) is in Documento/. To rebuild it from source:
cd Documento
latexmk -pdf main.tex # uses pdflatex + biber (biblatex)The controller was integrated into a real fixed-wing aircraft and flown. Orientation, altitude, pressure, temperature and GPS position were sent to the ground station, shown in real time and stored for later analysis. The flight tests showed some data loss and corruption over the nRF24L01 link (mostly altitude and pressure). The proposed next steps are:
See chapters Resultados and Conclusiones of the thesis for details.
@thesis{almanza2024flightcontroller,
author = {Almanza Gamba, Yesid Camilo},
title = {Desarrollo e implementación de un controlador de vuelo y estación de control de tierra para un UAV de ala fija},
school = {Universidad de los Andes},
type = {Bachelor's thesis},
year = {2024}
}Thanks to Prof. Alba Ávila Bernal for advising this project, and to @simonpine for contributions to the firmware and the GCS.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 330 Ω | Resistor_SMD:R_0805_2012Metric | R1, R2, R3, R4 |
| 4 | Conn_01x03 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | Encoder1, Pitot1, RX1, TX2 |
| 4 | LED | LED_SMD:LED_1206_3216Metric | D1, D2, D3, D4 |
| 4 | MountingHole | MountingHole:MountingHole_3mm_Pad | H1, H2, H3, H4 |
| 2 | 1000 uF | Capacitor_THT:CP_Radial_D8.0mm_P3.50mm | C1, C2 |
| 2 | Conn_01x02 | Connector_PinSocket_2.54mm:PinSocket_1x02_P2.54mm_Vertical | J9, J10 |
| 1 | 2200 uF | Capacitor_THT:CP_Radial_D8.0mm_P3.50mm | C3 |
| 1 | BNO055 | Library:BNO055 | J3 |
| 1 | Buzzer | Buzzer_Beeper:Buzzer_15x7.5RM7.6 | BZ1 |
| 1 | Conn_01x04_Pin | Connector_JST:JST_EH_B4B-EH-A_1x04_P2.50mm_Vertical | LIDAR1 |
| 1 | Conn_01x04_Pin | Library:OLED | Oled1 |
| 1 | Conn_01x05_Pin | Library:Hmc5883l Gy271 | Gy-271 |
| 1 | Conn_01x06_Pin | Library:module_bme280 | BMP280 |
| 1 | Conn_01x06_Pin | Connector_JST:JST_EH_B6B-EH-A_1x06_P2.50mm_Vertical | GPS-M10Q5883 |
| 1 | Conn_01x07 | Connector_PinHeader_2.54mm:PinHeader_1x07_P2.54mm_Vertical | J1 |
| 1 | ESP32-DEVKIT-V1 | esp32:MODULE_ESP32_DEVKIT_V1 | U2 |
| 1 | GND | Connector_PinHeader_2.54mm:PinHeader_1x07_P2.54mm_Vertical | J6 |
| 1 | J9 | Connector_PinSocket_2.54mm:PinSocket_2x04_P2.54mm_Vertical | NRF24L1 |
| 1 | MPU6050 | Library:module_mpu6050 | J7 |
| 1 | PCA9685 | Library:PCA 9685 | J4 |
| 1 | SDCARD | Connector_PinSocket_2.54mm:PinSocket_1x06_P2.54mm_Vertical | J2 |
| 1 | SW_SPDT | Library:Switch_Slide | SW2 |
| 1 | V7805-1000 | digikey-footprints:3-SIP_Module_V7805-1000 | U1 |
| 1 | XT60-M | Library:AMASS_XT60-M | J8 |
| 1 | vcc | Connector_PinHeader_2.54mm:PinHeader_1x07_P2.54mm_Vertical | J5 |

YesidAlmanzaGamba/Thesis-Flight-Controller-Fixed-Wing
This thesis addresses the critical need for efficient data management and operational control in fixed-wing UAVs, targeting the gaps in current commercial flight controllers.

YesidAlmanzaGamba/Thesis-Flight-Controller-Fixed-Wing
This thesis addresses the critical need for efficient data management and operational control in fixed-wing UAVs, targeting the gaps in current commercial flight controllers.



tclarke/kicad-mikroBUS
Kicad files for creating MikroBUS host boards and modules.




MukeshSethy/micromouse-runner
This is my repo for the first version of full size micromouse development.

pms67/HadesFCS
Complete flight control system designed from scratch. Hardware designed with KiCad.
It measures 156.4 × 71.6 mm and has 2 copper layers, 1.6 mm thick.
39 parts, built around the V7805-1000, PCA9685PW, BNO055 and XT60-M. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the YesidAlmanzaGamba/Thesis-Flight-Controller-Fixed-Wing repository on GitHub, at the commit this page was made from: the board is src/pcb/DELTA 1.0/C1/C1.kicad_pcb and its schematic PCB/Delta 1.0/C1.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask YesidAlmanzaGamba before reusing the design.