2 layers382 × 160 mm
E80-1800-pcb universal
ebastler/E80-1800
QMK compatible PCB replacement for Cherry G80-1800
451 parts86BSD-2-Clause
2 layers285.8 × 96.2 mm
Keyboard
xyzz/g602A simple 3d-printable oring gasket keyboard.
- Size
- 285.8 × 96.2 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 163
- Nets
- 113
- Pads
- 664
- Tracks, vias
- 879, 27
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 24 Dec 2020
- Updated
- 24 Dec 2020
Overview
Keyboard is an open-source printed circuit board by xyzz, from the xyzz/g60 repository on GitHub, published under the CC0-1.0 licence. It is a 2-layer board of 285.8 × 96.2 mm with 163 parts on 113 nets, routed with 879 tracks and 27 vias.
It is built around the SRV05-4 and XC6206P332MR. Its parts include 10 capacitors, 4 connectors, 3 resistors, 3 ICs and 2 switches. It belongs with the keyboards and input boards and the STM32 boards of this library.
Main components
2
SRV05-4
SOT-23-6L-55℃~+150℃ 15V 1pF 4A 5V 5uA 6V 80W ESD Four channels IEC 61000-4-2、IEC 61000-4-5 Unidirectional SOT-23-6L ESD and Surge Protection (TVS/ESD) ROHShongjiachengESD And Surge Protection (TVS/ESD)
XC6206P332MR
SOT-23-40℃~+85℃@(Ta) 1 1uA 200mA 3.3V 6V Fixed Over Current Protection Positive SOT-23-3L Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTorex SemiconductorVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
README
README.mdg60
A simple 3d-printable oring gasket keyboard.
Known issues
Depending on 3d print tolerances, plate and PCB edges might scratch against the corners of the case. Ideally, the outlines of both should be reduced a little bit. Unfortunately, these changes will not be done as a result of me losing interest in the project due to availability of Bakeneko.
Compatibility
The PCB is not compatible with other cases due to custom mounting point cutouts and USB position. In turn, the case is also not compatible with any third-party PCBs.
Oring size
Around 180mm ID and 3.5mm CS, for example AS568-263 should work fine.
Machinability
The case should be machinable, however it was not tested and I cannot suggest getting it machined due to extremely simplistic design (ie just make a Bakeneko instead).
License
This project is licensed under CC0, see the LICENSE file for more details, or tldrlegal.com for a summary.
Parts
163| Qty | Value | Footprint | References |
|---|---|---|---|
| 64 | D | Diode_SMD:D_SOD-123 | D_0, D_1, D_2, D_10, D_11, D_12, D_13, D_14, D_15, D_16, D_17, D_18, D_19, D_20, D_21, D_22 +48 |
| 50 | KEYSW | MX_Only:MXOnly-1U-NoLED | K_0, K_1, K_2, K_10, K_11, K_12, K_13, K_14, K_16, K_17, K_18, K_19, K_20, K_21, K_22, K_23 +34 |
| 7 | 1.25u | MX_Only:MXOnly-1.25U-NoLED | K_56, K_57, K_58, K_60, K_61, K_62, K_63 |
| 4 | 1.5u | MX_Only:MXOnly-1.5U-NoLED | K_156, K_158, K_161, K_163 |
| 4 | 100n | Capacitor_SMD:C_0603_1608Metric | C1, C7, C8, C10 |
| 3 | 1u | Capacitor_SMD:C_0603_1608Metric | C3, C5, C6 |
| 2 | 1u | MX_Only:MXOnly-1U-NoLED | K_157, K_162 |
| 2 | 4.7u | Capacitor_SMD:C_0603_1608Metric | C2, C4 |
| 2 | 5.1k | Resistor_SMD:R_0603_1608Metric | R2, R3 |
| 2 | KEYSW | MX_Only:MXOnly-1.5U-NoLED | K_15, K_28 |
| 1 | 10k | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | 10n | Capacitor_SMD:C_0603_1608Metric | C9 |
| 1 | 500mA | Fuse:Fuse_1206_3216Metric | F1 |
| 1 | 6.25u | MX_Only:MXOnly-6.25U-ReversedStabilizers-NoLED | K_59 |
| 1 | 7u | MX_Only:MXOnly-7U-ReversedStabilizers-NoLED | K_159 |
| 1 | BOOT | Button_Switch_SMD:SW_SPST_TL3342 | SW2 |
| 1 | Daughterboard | Connector_JST:JST_SH_SM04B-SRSS-TB_1x04-1MP_P1.00mm_Horizontal | J1 |
| 1 | GND | TestPoint:TestPoint_Pad_D1.5mm | J4 |
| 1 | HRO-TYPE-C-31-M-12 | Type-C:HRO-TYPE-C-31-M-12 | USB1 |
| 1 | KEYSW | MX_Only:MXOnly-1.25U-NoLED | K_42 |
| 1 | KEYSW | MX_Only:MXOnly-1.75U-NoLED | K_54 |
| 1 | KEYSW | MX_Only:MXOnly-2.25U-NoLED | K_41 |
| 1 | MX-NoLED | MX_Only:MXOnly-2.75U-NoLED | K_154 |
| 1 | MX-NoLED | MX_Only:MXOnly-2.25U-NoLED | K_142 |
| 1 | MX-NoLED | MX_Only:MXOnly-2U-NoLED | K_114 |
| 1 | RESET | Button_Switch_SMD:SW_SPST_TL3342 | SW1 |
| 1 | Regular | MX_Only:MXOnly-1.75U-NoLED | K_29 |
| 1 | SRV05-4 | Package_TO_SOT_SMD:SOT-23-6 | U1 |
| 1 | STM32F072C8Ux | Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.6x5.6mm | U2 |
| 1 | SWCLK | TestPoint:TestPoint_Pad_D1.5mm | J3 |
| 1 | SWDIO | TestPoint:TestPoint_Pad_D1.5mm | J2 |
| 1 | Stepped | MX_Only:MXOnly-1.25U-NoLED | K_129 |
| 1 | XC6206P332MR | Package_TO_SOT_SMD:SOT-23 | U3 |
Questions
How big is the Keyboard PCB?
It measures 285.8 × 96.2 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Keyboard use?
163 parts, built around the SRV05-4 and XC6206P332MR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Keyboard KiCad files?
From the xyzz/g60 repository on GitHub, at the commit this page was made from: the board is pcb/keyboard.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Keyboard design in my own project?
Its repository publishes it under the CC0-1.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
Similar boards
- 2 layers337.2 × 122.6 mm
- 2 layers337.2 × 122.5 mm
- 2 layers346.1 × 93.7 mm
Sifrl main pcb
ramonimbao/SpaceInvadersFRL
An F-rowless TKL keyboard case, plate, and PCB that uses the HiTek Series 725 switches.
177 parts15 - 2 layers194.3 × 79 mm
- 2 layers87 × 30.8 mm
- 2 layers170 × 120 mm
- 2 layers440.5 × 124.9 mm
Gear85 hotswap flex cut, number pad
cosmosalad/Gear80
Gear80 is a 80% keyboard based on the rp2040.
335 parts7MIT