Beogram esp32

Beonos Controller

Control your vintage Bang & Olufsen Beogram turntable from Home Assistant or Sonos.

What is it? ⬪ Buy a board ⬪ Which turntables ⬪ Hardware ⬪ Firmware ⬪ Repo layout ⬪ License

I recorded a full build video that you can watch here.

Buy a board

Get it as a kit, pre-soldered or not, from the Wells Workshop shop.

Or order your own Beonos Controller from PCBway. You can use my referral code to get $5 off your order, if you want. In my experience they're usually pretty fast and high quality, especially for the price.

What is it?

A small ESP32-C6-powered custom PCB that splices into a Beogram's keyboard cable, reads what the turntable is doing, and sends play/pause/stop commands. The result is a 'smart' vintage turntable that behaves like a digital Sonos source.

• Turntable → Sonos: start the turntable and the speaker switches to Line-In and plays. Pause or switch off, and the speaker pauses.
• Sonos → turntable: pick Line-In on the speaker and the turntable starts (it presses Cue). Switch away or pause, and the turntable stops. If there's no record on the platter, the firmware notices and pauses Sonos rather than leaving it playing silence.

The board splices in-line, so nothing about the turntable is modified permanently — unplug the two headers and it's stock again.

Which turntables

The Beogram 1800 family — the last generation of radial-arm Beograms — all share one control board, so the splice is the same across them:

The RX-2 service manual is published as a supplement to the Beogram 1800/2000/5000 manual, and the three share the same power supply (PCB 8005076) and control board (PCB 8005117). Their keyboards are the same two sub-boards — 8005070 for PLAY/STOP and 8005109 for 45/CUE/33 — landing on the same P7 pins, which is what this board splices into. The RX is unverified only because no manual was to hand; it replaced the 1800 and differs from the RX 2 mainly in being supplied with a pickup.

Not compatible. The Beogram 2200 looks close but wires its speed switches straight to the control board alongside indicator lamps and a motor relay, with no separate keyboard board and no CUE or PLAY/STOP lines to intercept. Tangential-arm Beograms (4002, 8000, 6500, 7000, 9000, 5005 and relatives) use a different arm and control system entirely, and pre-1983 radial decks predate this microcomputer control.

To identify an unknown deck, look for a control PCB stamped 8005117, a 24-pin MCU marked B040680 / ETL 5410N, and a keyboard on its own cable whose buttons switch +12V.

Hardware

• MCU: Seeed Studio XIAO ESP32-C6 (castellated edge-mount module)
• Button drivers: 2× LTV-356T optocouplers, switching the turntable's +12V onto the CUE and PLAYPAUSE lines exactly as the real buttons do
• Level shifters: 2× 1M/1.5M dividers dropping the COP410's 5.3V logic to ~3.18V for the ESP's 3.3V inputs. The values are deliberately high so the divider barely loads the COP410's weak CMOS outputs, and any overvoltage is current-limited into the ESP's ESD clamps.
• Power: an off-board MP1584EN buck module (PS1) steps the +12V button rail down to 5V, so the board draws everything from the button cable and never taps the 5.3V supply. The module hangs on flying leads; the board carries four wire pads for it.
• Decoupling: 10µF + 100nF on the buck's 5V output
• Input filtering: 10nF from each divider midpoint to ground, below R6/R8. The dividers present ~600kΩ to the ESP on wires that run past a motor; the caps give a ~6ms time constant, well inside the firmware's 50 ms debounce.
• Connectors: two 1×8 horizontal headers for the in-line splice — J1 (socket, silkscreened TO BOARD) and J2 (header, silkscreened TO KEYBOARD). Pins 1, 2, 4, 6, 7, 8 pass straight through; pins 3 and 5 also land on the optocoupler emitters.
• Flying leads: the two COP410 sense signals and a ground reference arrive on test pads (TP2, TP3, TP5); four more pads go out to the buck module. Everything is silkscreened by function — On-Off IN, PlayPause IN, GND IN, 12V, 5V, GND — so solder by the printed label, not the designator.

Board is 25 × 64 mm, two layers. Sources are beogram-esp32.kicad_pcb / .kicad_sch / .kicad_pro, with the BOM in bom.csv.

Pin map

D6/D7 (GPIO16/17) are UART0 and are left unconnected on purpose, so the ROM bootloader's serial output can't reach an optocoupler on reset.

Firmware (ESPHome)

pip install esphome
cp secrets.yaml.example secrets.yaml
# fill in WiFi creds in secrets.yaml
esphome run beogram-rx2.yaml

First flash needs USB-C; after that, updates go over the air.

Configuring the Sonos speaker

Once it joins WiFi the device shows up in Home Assistant. Set the "Sonos IP" entity to your speaker's address. That's the only setup — the RINCON UUID is discovered from the speaker on boot.

Exposed entities

Repo layout

beogram-esp32.kicad_pro     KiCad project
beogram-esp32.kicad_sch     Schematic
beogram-esp32.kicad_pcb     PCB layout
fp-lib-table                Registers the project footprint libraries
sym-lib-table               Registers the project symbol library
beogram.pretty/             Project footprints (MP1584 wire pads)
beogram.kicad_sym           Project symbols
New_XIAO_Series_Footprints/ Seeed's XIAO footprint library (vendor)
beogram-rx2.yaml            ESPHome firmware config
secrets.yaml.example        Template for WiFi/OTA/API creds
bom.csv                     Bill of materials
bang-olufsen_beogram_rx2_sch.pdf   RX 2 service-manual schematic, for reference

Credits

ESPHome, the Seeed Studio XIAO ESP32-C6, KiCad, and Bang & Olufsen's engineers, who documented the RX2 well enough to reverse a splice point out of it forty years later.

Donate

While beonos is free and open source, donations are deeply appreciated, and make ongoing development and support possible. Donate now

License

CC BY-NC-SA 4.0. © 2026 Wells Riley.