Skip to the content
2 layers143.5 × 94.2 mmMushyCloud, the printed circuit board in 3D

48 key split keyboard

Size
143.5 × 94.2 mm
Copper layers
2
Thickness
1.6 mm
Parts
91
Nets
46
Pads
316
Tracks, vias
488, 49
Pours
2
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
14 Apr 2021
Updated
15 Apr 2023

Overview

MushyCloud is an open-source printed circuit board by wozeparrot, from the wozeparrot/MushyCloud repository on GitHub. It is a 2-layer board of 143.5 × 94.2 mm with 91 parts on 46 nets, routed with 488 tracks and 49 vias.

Its parts include 40 connectors, 24 diodes, 24 switches and 1 IC. It belongs with the keyboards and input boards and the AVR (ATmega, ATtiny) boards of this library.

README

README.md

MushyCloud

A low profile 48 key ergonomic split keyboard.

Designed for Kailh choc switches to be super low profile. Fairly simplistic with an optional OLED display.

Building

Parts

Most of these parts can be sourced from AliExpress or local vendors.

  • 2x PCB
  • 2x Pro Micro
  • 2x 1x4 2.54 mm right angle pin header
  • 48x Kailh Choc switches
  • 48x 1N4148 diodes
  • (Optional) 1x 0.96" OLED

Assembly

Assembly is fairly straightforward.

The PCBs are designed to be reversible, so the same PCB will be used for both halves.

The following steps are for one half of the keyboard. Just repeat for the other half.

  1. Solder the diodes to the top side of the PCB.
  2. The switches should "clip" into the PCB. Basically just clip a switch in then solder the pins.
  3. Solder a right angle pin header to the top side of the PCB.
  4. Solder the Pro Micro to the top side of the PCB. On the left half, the Pro Micro should be right side up. On the right half, the Pro Micro should be upside down.
  5. (Optional) Solder the OLED to the left side of the PCB only. The OLED goes just below the pin header on the bottom set of pins.

Flashing

Uses a custom fork of QMK. See here.

Depending on your USB cable, it may be slightly difficult to get the USB cable to plug into the Pro Micro on the right half.

Flashing QMK is the same as any other split keyboard that uses QMK.

Parts

91
QtyValueFootprintReferences
35D2keebio-parts:SinglePadJ6, J6, J6, J6, J6, J6, J6, J6, J6, J6, J6, J6, J6, J6, J6, J6 +19
24DMushyCloud:DiodeD0, D1, D2, D10, D11, D12, D13, D15, D16, D17, D18, D19, D20, D21, D22, D23 +8
24SW_PushMushyCloud:Kailh-PG1350-1u-reversible-No-Clickhole-NoLEDSW1, SW2, SW10, SW11, SW12, SW13, SW14, SW16, SW17, SW18, SW19, SW20, SW21, SW22, SW23, SW24 +8
2Conn_01x04_MaleConnector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalJ4, J4
2LOGOMushyCloud:logoG***, G***
1Conn_01x02_MaleConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_HorizontalJ3
1Conn_01x03_MaleConnector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalJ1
1Conn_01x04_MaleConnector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_HorizontalJ2
1ProMicroMushyCloud:ArduinoProMicro-ZigZag-NoSilkU2

Similar boards

  • 2 layers237.5 × 102.9 mmAlu, the printed circuit board in 3D

    Alu

    jes/scamp-cpu

    A homebrew 16-bit CPU with a homebrew Unix-like-ish operating system.

    91 parts301Unlicense
  • 2 layers132.5 × 84.8 mmShieldXL M, the printed circuit board in 3D

    ShieldXL M

    okyeron/shieldXL

    A rework/remix of the monome norns shield

    91 parts179GPL-3.0
  • 2 layers100 × 68 mmSI4684 SMD, the printed circuit board in 3D

    SI4684 SMD

    PE5PVB/SI4684-DAB-Receiver

    SI4684 ESP32 DAB Receiver

    91 parts135GPL-3.0
  • 2 layers160 × 99.5 mmSupply Board, the printed circuit board in 3D

    Supply Board

    jherkenhoff/STM

    DIY scanning tunneling microscope (STM)

    91 parts88
  • 2 layers213 × 60 mmVController main board, the printed circuit board in 3D

    VController main board

    sixeight7/VController_v3

    Production model of the VController, VC-mini and VC-touch

    91 parts80
  • 2 layers301.6 × 116.9 mmOpus, the printed circuit board in 3D

    Opus

    cfbender/keyboards

    A collection of all of my keyboard projects

    91 parts64MPL-2.0
  • 2 layers89 × 123.4 mmNsec badge-2025, the printed circuit board in 3D

    Nsec badge-2025

    nsec/nsec-badge

    Software from the NorthSec badge

    91 parts62
  • 2 layers167 × 122.8 mmBoardv3, the printed circuit board in 3D

    Boardv3

    compressionKeyboards/compression4c

    This repo contains the files to order a custom PCB for (4c), checkout the zmk layout to build firmware!

    91 parts60

Questions

How big is the MushyCloud PCB?

It measures 143.5 × 94.2 mm and has 2 copper layers, 1.6 mm thick.

What parts does the MushyCloud use?

91 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the MushyCloud KiCad files?

From the wozeparrot/MushyCloud repository on GitHub, at the commit this page was made from: the board is pcb/MushyCloud.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the MushyCloud design in my own project?

Its repository states no licence, so its author keeps all rights: ask wozeparrot before reusing the design.