

Safe chicks
Chicken door to keep them chicks safe
- Size
- 40 × 53 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 53
- Nets
- 43
- Pads
- 179
- Tracks, vias
- 220, 26
- Pours
- 3
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 17 Mar 2025
- Updated
- 31 Dec 2025
Overview
Safe chicks is an open-source printed circuit board by WouterThys, from the WouterThys/SafeChicks repository on GitHub. It is a 2-layer board of 40 × 53 mm with 53 parts on 43 nets, routed with 220 tracks and 26 vias.
Its parts include 19 resistors, 12 capacitors, 6 inductors, 4 connectors and 1 IC. It belongs with the PIC boards of this library.
README
readme.mdSafe Chicks
Chicks need to be safe so make door go brrrr.
Ideas/Notes
- Chord attacked to door and motor winds up/down to open/close door
- Light sensor
- Limit switch -> use the iCab galenus switches? -> magnetic so will not weir out I guess
- Solar powered?
- Controller? What I have is:
- Pico Pi
- Arduino
- Raspberry pi 3
- Beaglebone black
- Adafruit Huzzah -> has ESP..
- Camera to see if checks are there -> would need raspberry for that (arduino is too lightweight)
- DC motor https://www.farnell.com/datasheets/4376711.pdf?_gl=1*1atfsg3*_gcl_au*MjAyNTY1MDc1NS4xNzQxNjI0NTgy
Used in V2
Mouser
426-DRI0044 Fabrik. Artikelnum.: DRI0044 DFRobot 2x1.2A DC Motor Driv / Stroombeheer IC Ontwikkelinghulpmiddelen TARIC:8473302000 ECCN:EAR99 COO:CN
426-FIT0489-D Fabrik. Artikelnum.: FIT0489-D DFRobot Turbo Metal Gear Wor / DFRobo-accessoires TARIC:8471500090 ECCN:EAR99 COO:CN
653-D2HW-C223MR Fabrik. Artikelnum.: D2HW-C223MR Omron Electronics Subminiature Basic S / Basis- / klikschakelaars TARIC:8536508099 ECCN:EAR99 COO:IT
RobotShop
RB-Jsu-84 37mm Motor Mount For Titan Series (Pair) 5-4-G 1 1 0 €5.71 €5.71 RB-Sct-941 15T Timing Pinion Pulley (6mm) 02-6-B 1 1 0 €9.45 €9.45 RB-Phi-457 Waterproof Enclosure 200x120x75 w/ Transparent Lid M05-2-D 1 1 0 €13.12 €13.12

Usefull links
DIY chicken door: https://davenaves.com/blog/interests-projects/chickens/chicken-coop/arduino-chicken-door/#
Battery management system https://www.dfrobot.com/product-1714.html
Arduino low power https://docs.arduino.cc/learn/electronics/low-power/
Measurements
POC Arduino Uno (17/03 16:20)
- added 4[Ohm] resistor between 12V supply
- Idle ~140mV => 4,9 mW
- Run ~1,30V => 423 mW
Parts
53| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 1k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R8, R9, R12, R13, R14, R15 |
| 6 | LED_Small | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | L1, L2, L3, L4, L5, L6 |
| 5 | 10k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R10, R11, R18, R20 |
| 4 | 100k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R6, R7, R17, R19 |
| 4 | 100n | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C2, C4, C10 |
| 4 | 1u | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C8, C9, C11, C12 |
| 4 | MountingHole | MountingHole:MountingHole_3.2mm_M3_Pad_Via | H1, H2, H3, H4 |
| 2 | 10n | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C6, C7 |
| 2 | 613k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R2, R3 |
| 1 | 1007 | Diode_THT:D_DO-15_P10.16mm_Horizontal | D1 |
| 1 | 10u | Capacitor_Tantalum_SMD:CP_EIA-3216-10_Kemet-I_HandSolder | C5 |
| 1 | 16MHz | Crystal:Crystal_HC49-U_Vertical | 16Mhz |
| 1 | 1u | Capacitor_Tantalum_SMD:CP_EIA-3216-10_Kemet-I_HandSolder | C3 |
| 1 | 332k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R4 |
| 1 | 47k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R16 |
| 1 | 5V | TerminalBlock:TerminalBlock_bornier-2_P5.08mm | J1 |
| 1 | Buttons | Connector_Molex:Molex_PicoBlade_53047-0410_1x04_P1.25mm_Vertical | Buttons |
| 1 | LED-Enable | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J9 |
| 1 | MTR | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | Motor |
| 1 | PGM | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J2 |
| 1 | PIC18F2550-ISP | Package_DIP:DIP-28_W7.62mm | U1 |
| 1 | Reset | Button_Switch_THT:SW_PUSH_6mm_H4.3mm | Reset |
| 1 | Sensors | Connector_Molex:Molex_PicoBlade_53047-0410_1x04_P1.25mm_Vertical | J6 |
| 1 | Serial | Connector_Molex:Molex_PicoBlade_53047-0410_1x04_P1.25mm_Vertical | UART |
| 1 | Switches | Connector_Molex:Molex_PicoBlade_53047-0410_1x04_P1.25mm_Vertical | Switches |
More from WouterThys/SafeChicks
2- 2 layers40 × 53 mm

- 2 layers78 × 68 mm

Similar boards
- 2 layers217.1 × 393.8 mm

Sweepv2
davidphilipbarr/Sweep
Sweep - a small promicro based keyboard inspired by the Ferris.
53 parts2.1k - 2 layers121.9 × 81.3 mm

Rgb to hdmi
hoglet67/RGBtoHDMI
Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI
53 parts1kGPL-3.0 - 2 layers48 × 48 mm

- 2 layers103.7 × 74.1 mm

PicoGUS
polpo/picogus
Emulation of ISA sound cards and CD-ROM on Raspberry Pi Pico (GUS, SB/Adlib, MPU-401, Tandy, CMS, Panasonic CD-ROM) with USB mouse/joystick support
53 parts805 - 2 layers60.5 × 76.8 mm

Headphones prototype pcb
strangeparts/niubi-headphones
Flexible circuit board design for adding a headphone jack to an iPhone 7
53 parts493MIT - 2 layers59.1 × 26.1 mm

- 2 layers49 × 49 mm

Open source BMS
Teslafly/Dead-OpenBMS-dead
A scalable, open source battery management system
53 parts248 - 2 layers39 × 40 mm

Mdb bridge esp32s3
nodestark/mdb-esp32-cashless
ESP32-based MDB cashless device for vending machines, supporting EVA DTS DEX/DDCMP telemetry and payments over the MDB protocol via Bluetooth and MQTT
53 parts190MIT
Questions
How big is the Safe chicks PCB?
It measures 40 × 53 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Safe chicks use?
53 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Safe chicks KiCad files?
From the WouterThys/SafeChicks repository on GitHub, at the commit this page was made from: the board is V2/PCB/safe_chicks/safe_chicks.kicad_pcb and its schematic V1/PCB/safe_chicks/safe_chicks.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Safe chicks design in my own project?
Its repository states no licence, so its author keeps all rights: ask WouterThys before reusing the design.