Skip to the content
2 layers74 × 82.2 mmPanel a25, the printed circuit board in 3D

MacPro6,2: open PCB redesign of the Mac Pro Late 2013 (trashcan) with new CPU, GPU/storage face modules, backplane and I/O boards (KiCad).

Size
74 × 82.2 mm
Copper layers
2
Thickness
0.11 mm
Parts
34
Nets
50
Pads
354
Tracks, vias
825, 88
Pours
73
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
1 Oct 2026
Updated
7 Nov 2026

Overview

Panel a25 is an open-source printed circuit board by winkleplex10-bit, from the winkleplex10-bit/The-Mac-Pro-Project repository on GitHub. It is a 2-layer board of 74 × 82.2 mm with 34 parts on 50 nets, routed with 825 tracks and 88 vias.

Its parts include 8 connectors, 4 capacitors and 4 ICs.

README

archive/kicad/macpro62-storage-face/README.md

MP62 Face S storage module SM-1 rev A0: KiCad 9 project

4 × M.2 2280 NVMe behind an ASMedia ASM2824 PCIe Gen3 switch, on the MP62-FACE v0.1 outline. The plan, BOM, cost and RAID analysis are in /workspace/macpro62-storage-board-plan.md. The spec is macpro62-face-module-spec-v0.1.md §11.3 (update 3).

Status: FLOORPLAN, not routed.

  • PCB: outline, holes, stackup (JLC06161H-2116, 6 layers), rule areas (both-side bus-bar keep-outs, core tab, J_PCIE plug zone), and every IC, connector, socket, standoff, inductor and bulk capacitor placed. Only the lug nets are on the PCB.
  • kicad-cli pcb drc: 0 violations, 0 unconnected, 0 footprint errors.
  • Schematic (macpro62-storage-face.kicad_sch, one flat A0 sheet, label connectivity, 154 symbols): kicad-cli sch erc: 0 errors, 0 warnings.

Frame

  • Same as the template. Module frame origin at the outline's bottom-left, viewed from the core side. Spec (X, Y) → KiCad (60 + X, 190 − Y).
  • F = core side (ASM2824 on the die pad, switch support parts ≤ 2 mm).
  • B = outer side (J_PCIE, J_AUX, 4 × M.2, power band).

PLACEHOLDERS (replace before routing)

FootprintWhy
MP62_M2_MKey_SMT_H4.2_PLACEHOLDERGeneric 67-pad M-key pattern (0.5 mm per row, rows offset 0.25), hold-downs and pegs are guesses. Use the LOTES APCI0107-P001A (LCSC C841661) drawing. The card-edge datum (origin) and the 2280 outline on F.Fab are correct per the M.2 form factor
MP62_BGA-492_21x21mm_Layout25x25_P0.8mm_PLACEHOLDERASM2824 ball map under NDA; 0.8 mm pitch assumed
MP62_TI_RNN0018A_VQFN-HR-18_3.5x3.5mm_PLACEHOLDERTPS56C215 HotRod pads; use TI RNN0018A
MP62_M2_Standoff_SMT_M2_Pad5.0Round pad; height must match the socket's card-bottom height (≈ 3.5 mm for H4.2, verify)

Symbols with logical pin numbering: ASM2824, TPS259824, TPS56C215, TLV62585. Real pinouts: M.2 M-key, MCIO 124 (from the spec CSV), GH15, BL24C64A, TMP1075, 74LVC2G07, SPI NOR, LM74700.

Layers

  • User.1: core contact zones.
  • User.2: outer height-zone lines.
  • User.3: connector band.
  • User.4: M.2 card outlines (host parts under a card ≤ 1.6 mm).
  • Dwgs.User: stock X-bracket (not fitted, deviation D-S1 / spec C-19).
  • Cmts.User: notes.

Rebuild

text
python3 tools/make_footprints.py        # template footprints (MP62_Face.pretty)
python3 tools/make_storage_fps.py       # MP62_Storage.pretty
python3 tools/build_storage.py          # PCB floorplan (KiCad 9 pcbnew python)
python3 tools/postprocess.py            # stackup + netclasses (PCIE_85R, REFCLK_85R, PWR_12V, PWR_3V3)
python3 tools/build_sch.py              # MP62_Storage.kicad_sym + schematic
kicad-cli pcb drc --severity-all -o drc_report.txt macpro62-storage-face.kicad_pcb
kicad-cli sch erc --severity-all -o erc_report.txt macpro62-storage-face.kicad_sch
/workspace/cadenv/bin/python tools/floorplan.py   # floorplan_storage_SM1.png

ICD rev 2 (2026-10-02)

  • U13 INA228 (VSSOP-10, FACE_SMB 0x40, ALERT → FACE_SMB_ALERT#) + R520 2 mΩ 2512 between +12V_PROT and +12V_PROT_S (ahead of U2) + C520; B side at (51.5, 143) / (44, 143) / (51.5, 140.5). DRC 0/0, ERC 0, 157 schematic instances. Renders not refreshed.

ICD rev 3 / O-10 (2026-10-04 ≈ 09:10 ET, Aidan approved)

  • J1 (J_PCIE, MCIO 124 RA) X 43.5 → 47.0 (+3.5 mm), narrow-plug courtyard (±21.6). Zero-jog landing at BP fp6 s = +5.0. Nearest B courtyard MH080 0.34 mm; M.2 card bottom Y 28.5 vs J1 body top Y 24.57 (3.9 mm). tools/floorplan.py reads J_PCIE X from face_geom.json.
  • Nothing routed besides the lug nets, so no re-route. DRC 0/0/0, ERC 0/0 (schematic unchanged). floorplan_storage_SM1.png, render_core_side_F.png, render_outer_side_B.png regenerated (kicad-cli svg + rsvg-convert).

Next steps

  1. Get the ASM2824 datasheet and ball map, plus the LOTES drawing.
  2. Replace the placeholders.
  3. Update the PCB from the schematic and place the ≈ 120 small passives.
  4. Route: PCIe Gen3, ≤ 2 vias per lane; 3V3_SSD on the L4 plane plus B-side pours; 12 V pours.
  5. Run DRC and get a JLC quote.

Parts

34
QtyValueFootprintReferences
8Fiducial_1mm_Mask2mmFiducial_1mm_Mask2mmFID1, FID2, FID3, FID4, FID5, FID6, FID7, FID8
6TDR_LAUNCHTP1A_T, TP1B_T, TP2A_T, TP2B_T, TP3A_T, TP3B_T
4100nF 0201 X5R 10V (3V3_MOD)MP62_MOD:C_0201_0603MetricC1_A1, C1_A2, C1_A3, C1_A4
4BL24C02F-NTRC (C2828222) 24C02 ID EEPROM @0x50MP62_MOD:DFN-8-1EP_2x3mm_P0.5mm_EP0.61x2.2mmU1_A1, U1_A2, U1_A3, U1_A4
4DF40C-50DP-0.4V(51) C424645 -> JMn DF40C-50DS (PMI-50 v2)MP62_MOD:MP62_Hirose_DF40C-50DP-0.4VJ2_A1, J2_A2, J2_A3, J2_A4
4MOD-A - Hong Cheng HC-USB3.0-L137-WJ (C7501870) THT, H 13.7; alt kinghelm KH-3.0AF180ZJ-11.5JB (C2979037, H 11.5)MP62_MOD:MP62_MOD_USB_A3_HC-USB3.0-L137-WJJ1_A1, J1_A2, J1_A3, J1_A4
4TOOLING_2.0TH1, TH2, TH3, TH4

More from winkleplex10-bit/The-Mac-Pro-Project

12
  • 6 layersBackplane, the printed circuit board in 3D

    Backplane

    winkleplex10-bit/The-Mac-Pro-Project

    MacPro6,2: open PCB redesign of the Mac Pro Late 2013 (trashcan) with new CPU, GPU/storage face modules, backplane and I/O boards (KiCad).

    221 parts
  • 4 layersBackplane, the printed circuit board in 3D

    Backplane

    winkleplex10-bit/The-Mac-Pro-Project

    MacPro6,2: open PCB redesign of the Mac Pro Late 2013 (trashcan) with new CPU, GPU/storage face modules, backplane and I/O boards (KiCad).

    152 parts
  • 4 layers104 × 166 mmMacpro62-storage face-2x, the printed circuit board in 3D

    Macpro62-storage face-2x

    winkleplex10-bit/The-Mac-Pro-Project

    MacPro6,2: open PCB redesign of the Mac Pro Late 2013 (trashcan) with new CPU, GPU/storage face modules, backplane and I/O boards (KiCad).

    89 parts
  • 6 layers104 × 166 mmMacpro62-storage face, the printed circuit board in 3D

    Macpro62-storage face

    winkleplex10-bit/The-Mac-Pro-Project

    MacPro6,2: open PCB redesign of the Mac Pro Late 2013 (trashcan) with new CPU, GPU/storage face modules, backplane and I/O boards (KiCad).

    76 parts
  • 10 layers156 × 167.8 mmMacpro62 am5, the printed circuit board in 3D

    Macpro62 am5

    winkleplex10-bit/The-Mac-Pro-Project

    MacPro6,2: open PCB redesign of the Mac Pro Late 2013 (trashcan) with new CPU, GPU/storage face modules, backplane and I/O boards (KiCad).

    57 parts
  • 2 layers99.3 × 98.1 mmPanel c50, the printed circuit board in 3D

    Panel c50

    winkleplex10-bit/The-Mac-Pro-Project

    MacPro6,2: open PCB redesign of the Mac Pro Late 2013 (trashcan) with new CPU, GPU/storage face modules, backplane and I/O boards (KiCad).

    55 parts
  • 10 layers156 × 167.8 mmMacpro62 lga1700, the printed circuit board in 3D

    Macpro62 lga1700

    winkleplex10-bit/The-Mac-Pro-Project

    MacPro6,2: open PCB redesign of the Mac Pro Late 2013 (trashcan) with new CPU, GPU/storage face modules, backplane and I/O boards (KiCad).

    53 parts
  • 2 layers58 × 34 mmTdr coupon c50, the printed circuit board in 3D

    Tdr coupon c50

    winkleplex10-bit/The-Mac-Pro-Project

    MacPro6,2: open PCB redesign of the Mac Pro Late 2013 (trashcan) with new CPU, GPU/storage face modules, backplane and I/O boards (KiCad).

    12 parts
  • 2 layers58 × 19 mmTdr coupon a25, the printed circuit board in 3D

    Tdr coupon a25

    winkleplex10-bit/The-Mac-Pro-Project

    MacPro6,2: open PCB redesign of the Mac Pro Late 2013 (trashcan) with new CPU, GPU/storage face modules, backplane and I/O boards (KiCad).

    6 parts
  • 2 layers44.7 × 9.7 mmMod hdmi, the printed circuit board in 3D

    Mod hdmi

    winkleplex10-bit/The-Mac-Pro-Project

    MacPro6,2: open PCB redesign of the Mac Pro Late 2013 (trashcan) with new CPU, GPU/storage face modules, backplane and I/O boards (KiCad).

    4 parts
  • 2 layers42.1 × 8.8 mmMod usba, the printed circuit board in 3D

    Mod usba

    winkleplex10-bit/The-Mac-Pro-Project

    MacPro6,2: open PCB redesign of the Mac Pro Late 2013 (trashcan) with new CPU, GPU/storage face modules, backplane and I/O boards (KiCad).

    4 parts
  • 2 layers40.1 × 8.8 mmMod usbc, the printed circuit board in 3D

    Mod usbc

    winkleplex10-bit/The-Mac-Pro-Project

    MacPro6,2: open PCB redesign of the Mac Pro Late 2013 (trashcan) with new CPU, GPU/storage face modules, backplane and I/O boards (KiCad).

    4 parts

Similar boards

  • 2 layers26 × 30 mmMicrocontroller, the printed circuit board in 3D

    Microcontroller

    FrameworkComputer/ExpansionCards

    Reference designs and documentation to create Expansion Cards for the Framework Laptop

    34 parts1.1kCC-BY-4.0
  • 2 layers171.2 × 72.9 mmAmiga gfxcard old, the printed circuit board in 3D

    Amiga gfxcard old

    mntmn/amiga2000-gfxcard

    MNT VA2000, an Open Source Amiga 2/3/4000 Graphics Card (Zorro II/III), written in Verilog

    34 parts1k
  • 2 layers53.5 × 62.5 mmLed matrix, the printed circuit board in 3D

    Led matrix

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    34 parts915
  • 2 layers45 × 26 mmESP32-HELP Button, the printed circuit board in 3D

    ESP32-HELP Button

    pcbreflux/espressif

    all espressif stuff will committed here

    34 parts608GPL-3.0
  • 2 layers41.7 × 25.7 mmHeadphones flex pcb rigid, the printed circuit board in 3D

    Headphones flex pcb rigid

    strangeparts/niubi-headphones

    Flexible circuit board design for adding a headphone jack to an iPhone 7

    34 parts493MIT
  • 2 layers18.8 × 16.3 mmAmoeba, the printed circuit board in 3D

    Amoeba

    mtl/keyboard-pcbs

    Keyboard PCBs

    34 parts485
  • 2 layers127 × 69.9 mmEzcgi, the printed circuit board in 3D

    Ezcgi

    baldengineer/bit-preserve

    Project for capturing vintage, classic, aka old computer schematics in KiCad.

    34 parts446

Questions

How big is the Panel a25 PCB?

It measures 74 × 82.2 mm and has 2 copper layers, 0.11 mm thick.

What parts does the Panel a25 use?

34 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Panel a25 KiCad files?

From the winkleplex10-bit/The-Mac-Pro-Project repository on GitHub, at the commit this page was made from: the board is boards/io/modules/panel/panel_a25/panel_a25.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Panel a25 design in my own project?

Its repository states no licence, so its author keeps all rights: ask winkleplex10-bit before reusing the design.