Skip to the content
2 layers99.1 × 99.1 mmNuBoard, the printed circuit board in 3D

Verified 2026-09-24 with KiCad 10.0.6. Open nuBoard.kicadpcb in this directory to inspect the result. This is a PCB-only candidate, separate from the main-board schematic and PCB.

Size
99.1 × 99.1 mm
Copper layers
2
Thickness
1.6 mm
Parts
20
Nets
123
Pads
300
Tracks, vias
619, 50
Pours
2
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
16 Sep 2026
Updated
12 Oct 2026

Overview

NuBoard is an open-source printed circuit board by wickerwaka, from the wickerwaka/nuBoard repository on GitHub. It is a 2-layer board of 99.1 × 99.1 mm with 20 parts on 123 nets, routed with 619 tracks and 50 vias.

Its parts include 16 capacitors, 2 resistors, 1 IC and 1 connector.

README

hardware/main-board/routing/hyperram-top/README.md

Matched top-layer HyperRAM routing candidate

Promoted to the main-board project on 2026-09-24. The authoritative PCB is now ../../nuBoard.kicad_pcb, with its schematic, pin-map CSV and displaced-signal FPGA constraints synchronized. This directory remains the verified pre-promotion reference snapshot; the description below records its original candidate status.

Verified 2026-09-24 with KiCad 10.0.6. Open nuBoard.kicad_pcb in this directory to inspect the result. This is a PCB-only candidate, separate from the main-board schematic and PCB. Do not update it from the unchanged main schematic: its pin allocation is different.

U2 and all 585 HyperRAM signal track segments (DQ0–7, CK, RWDS, CS# and RESET#) are locked against accidental editing. U2's power connections are still unrouted; shared board power networks were not locked.

Result

All ten required signals—CK, DQ0–7 and RWDS—are continuous, unbranched FPGA-pad-center to RAM-pad-center paths on F.Cu only, with zero vias. The PCB-only length spread is 0.214807 mm (8.457 mil), below the 0.381 mm (15 mil) limit by 0.166193 mm. No package compensation is configured. Unknown IC package skew is outside this approved requirement.

SignalFPGA ballRAM ballPCB length (mm)
DQ0K1D310.999998
DQ1L1D210.999991
DQ2H1C411.000001
DQ3J1D411.000009
DQ4G1D511.000003
DQ5K2E311.000000
DQ6L2E210.999998
DQ7M3E110.999998
CKM1B211.000000
RWDSL3C311.214798

U2 remains on F.Cu at (90.8, 75.0) mm, 90°. No additional package movement or pin-map change from the last surface-routing trial was needed. CS# uses G3/A3 and RESET# uses G2/A4; their FPGA-to-RAM paths are also F.Cu-only without vias, but their pull-up branches remain unfinished.

The tuning patterns occupy the straight corridor between approximately x=93.3 and 99.0 mm. Coordinating their direction and spacing avoided the failed approach of inserting isolated large detours into crowded traces. CK and DQ0–7 target 11.0 mm; RWDS retains its original 11.214798 mm route. Trace width is 0.0762 mm, pattern period 0.44 mm, each bump's baseline width 0.22 mm, and corner bevel 0.01 mm. Bump counts for DQ0–7 are 9, 9, 2, 13, 3, 6, 10, 10 respectively; CK has one bump.

All 15 displaced signals retain the replacement routes documented in hyperram-top-layer-plan.md. Their nets have no unconnected items in the final DRC report.

Verification

  • drc.json: fresh DRC with copper zones refilled and the copied main-board project/rules. No length-skew, shorting, clearance, hole-clearance or courtyard violations. Six dangling-track warnings remain outside the fast group, along with 27 whole-board unconnected items.
  • verification.json: independent pad-to-pad graph/length audit, with SHA-256 hashes of the checked PCB and DRC report. It checks both endpoint identities, DDIO capability, RWDS clock capability, absence of branches, disconnected copper and self-crossings, F.Cu-only routing, zero vias, unset package compensation, and the ten-net maximum length spread.
  • validation/test_hyperram_surface.py: mutation tests reject an open segment, a via, a bottom-layer segment, excessive length, a dangling branch and package compensation, even with the previously clean DRC.

From the repository root, repeat:

sh
kicad-cli pcb drc --refill-zones --format json \
  -o hardware/main-board/routing/hyperram-top/drc.json \
  hardware/main-board/routing/hyperram-top/nuBoard.kicad_pcb

# Use KiCad's Python environment (pcbnew and shapely are required).
python3 hardware/main-board/validation/check_hyperram_surface.py \
  hardware/main-board/routing/hyperram-top/nuBoard.kicad_pcb \
  --drc hardware/main-board/routing/hyperram-top/drc.json
python3 hardware/main-board/validation/test_hyperram_surface.py

On this Mac the Python executable used was /Applications/KiCad/KiCad.app/Contents/Frameworks/Python.framework/Versions/3.9/bin/python3.

Not full-board signoff

The requested ten-signal routing/length objective is met in this candidate. The whole board is not fabrication-ready. Power/bypass routing, CS#/RESET# pull-up connections, existing unrelated open connections, and main-project schematic/CSV/FPGA-constraint synchronization remain to do. The main project has deliberately not been overwritten by this candidate.

Geometric length matching is not a signal-integrity simulation or Efinity timing closure. The allocation spans clock regions L3–L6; validate RWDS capture phase/distribution, DDIO implementation, and timing with the actual HyperRAM controller. The existing APS1604M controller remains incompatible.

Parts

20
QtyValueFootprintReferences
10100nFCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC1, C2, C3, C4, C5, C6, C7, C8, C9, C10
5330pFCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC11, C12, C13, C14, C15
247kResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR1, R2
110uFCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC16
1MC68030RC25B68030:CPGA-128_MC68030_RCU1
1nuMezzanine_4x34nuBoard:nuMezzanine_4x34_P2.54mmJ1

More from wickerwaka/nuBoard

8
  • 6 layers141.7 × 105.1 mmNuBoard, the printed circuit board in 3D

    NuBoard

    wickerwaka/nuBoard

    Verified 2026-09-24 with KiCad 10.0.6. Open nuBoard.kicadpcb in this directory to inspect the result. This is a PCB-only candidate, separate from the main-board schematic and PCB.

    330 parts1
  • 2 layers99.1 × 99.1 mmV35s, the printed circuit board in 3D

    V35s

    wickerwaka/nuBoard

    Verified 2026-09-24 with KiCad 10.0.6. Open nuBoard.kicadpcb in this directory to inspect the result. This is a PCB-only candidate, separate from the main-board schematic and PCB.

    13 parts1
  • 2 layers99.1 × 99.1 mmZ80, the printed circuit board in 3D

    Z80

    wickerwaka/nuBoard

    Verified 2026-09-24 with KiCad 10.0.6. Open nuBoard.kicadpcb in this directory to inspect the result. This is a PCB-only candidate, separate from the main-board schematic and PCB.

    13 parts1
  • 2 layers99.1 × 99.1 mmNuBoard, the printed circuit board in 3D

    NuBoard

    wickerwaka/nuBoard

    Verified 2026-09-24 with KiCad 10.0.6. Open nuBoard.kicadpcb in this directory to inspect the result. This is a PCB-only candidate, separate from the main-board schematic and PCB.

    10 parts1
  • 8 layersBuffer, the printed circuit board in 3D

    Buffer

    wickerwaka/nuBoard

    Verified 2026-09-24 with KiCad 10.0.6. Open nuBoard.kicadpcb in this directory to inspect the result. This is a PCB-only candidate, separate from the main-board schematic and PCB.

    7 parts1
  • 2 layers99.1 × 99.1 mmNuBoard, the printed circuit board in 3D

    NuBoard

    wickerwaka/nuBoard

    Verified 2026-09-24 with KiCad 10.0.6. Open nuBoard.kicadpcb in this directory to inspect the result. This is a PCB-only candidate, separate from the main-board schematic and PCB.

    6 parts1
  • 6 layersClock Buffer, the printed circuit board in 3D

    Clock Buffer

    wickerwaka/nuBoard

    Verified 2026-09-24 with KiCad 10.0.6. Open nuBoard.kicadpcb in this directory to inspect the result. This is a PCB-only candidate, separate from the main-board schematic and PCB.

    5 parts1
  • 6 layersOutput LED, the printed circuit board in 3D

    Output LED

    wickerwaka/nuBoard

    Verified 2026-09-24 with KiCad 10.0.6. Open nuBoard.kicadpcb in this directory to inspect the result. This is a PCB-only candidate, separate from the main-board schematic and PCB.

    5 parts1

Similar boards

  • 2 layers66.9 × 74.5 mmDeskHop Rev1, the printed circuit board in 3D

    DeskHop Rev1

    hrvach/deskhop

    Fast Desktop Switching Device

    20 parts7.9kGPL-3.0
  • 2 layers86.4 × 64.8 mmSlot machine, the printed circuit board in 3D

    Slot machine

    google/google-ctf

    Google CTF

    20 parts5.1kApache-2.0
  • 2 layers36.2 × 26.8 mmEsp32 minimal, the printed circuit board in 3D

    Esp32 minimal

    atopile/atopile

    Design circuit boards with code! ✨ Get software-like design reuse 🚀, validation, version control and collaboration in hardware; starting with electronics ⚡️

    20 parts4kMIT
  • 2 layers108.1 × 393.8 mmSweep compact ble, the printed circuit board in 3D

    Sweep compact ble

    davidphilipbarr/Sweep

    Sweep - a small promicro based keyboard inspired by the Ferris.

    20 parts2.1k
  • 2 layers26 × 15.9 mmTPS54340 Buck Regulator, the printed circuit board in 3D

    TPS54340 Buck Regulator

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    20 parts1.2k
  • 2 layers67.6 × 30.5 mmRgb to hdmi, the printed circuit board in 3D

    Rgb to hdmi

    hoglet67/RGBtoHDMI

    Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

    20 parts1kGPL-3.0
  • 2 layers44.3 × 28.7 mmLin bus adapter esp32, the printed circuit board in 3D

    Lin bus adapter esp32

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    20 parts915
  • 2 layers89.5 × 61.6 mmFreeDeck TH 2020-02, the printed circuit board in 3D

    FreeDeck TH 2020-02

    FreeYourStream/freedeck-hardware

    all the stuff you need to build your own FreeDeck

    20 parts772

Questions

How big is the NuBoard PCB?

It measures 99.1 × 99.1 mm and has 2 copper layers, 1.6 mm thick.

What parts does the NuBoard use?

20 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the NuBoard KiCad files?

From the wickerwaka/nuBoard repository on GitHub, at the commit this page was made from: the board is hardware/68030/68030.kicad_pcb and its schematic hardware/68000/68000.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the NuBoard design in my own project?

Its repository states no licence, so its author keeps all rights: ask wickerwaka before reusing the design.