Skip to the content
2 layers160 × 159 mmLisn pcb, the printed circuit board in 3D

The leery-lisn contains a LISN network on both the neutral and line connections of the AC plug and a common mode / differential mode separator, allowing for measurement of both the differential mode and common mode…

Size
160 × 159 mm
Copper layers
2
Thickness
1.6 mm
Parts
88
Nets
35
Pads
212
Tracks, vias
147, 238
Pours
64
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
14 Jul 2021
Updated
28 Sep 2021

Overview

Lisn pcb is an open-source printed circuit board by westonb, from the westonb/leery-lisn repository on GitHub. It is a 2-layer board of 160 × 159 mm with 88 parts on 35 nets, routed with 147 tracks and 238 vias.

It is built around the 2045-09-BLF, BAV23S and ADT2-71T+. Its parts include 42 resistors, 12 capacitors, 12 inductors, 9 connectors and 4 diodes.

Main components

3

README

README.md

leery-lisn

A open source dual AC LISN with integrated common mode / differential mode separator and transient limiter.

Schematic here

Summary

The leery-lisn is a Line Impedance Stabilization Network (LISN) for pre-compliance conducted EMI measurements of devices that plug into the AC line. A LISN goes between a device and the AC outlet and provides a known AC line impedance, allowing for repeatable measurements of conducted noise generated by the device. It also contains circuitry to couple the noise to a 50 ohm RF output to allow for measurement with a spectrum analyzer.

The leery-lisn contains a LISN network on both the neutral and line connections of the AC plug and a common mode / differential mode separator, allowing for measurement of both the differential mode and common mode noise generated by a device. It also contains a transient limiter to protect a connected spectrum analyzer from transients on the AC line or plugging the LISN into the AC line when the spectrum analyzer is already connected.

The design of the leery-lisn is loosely based on the LISN designs from this thread on the EEVBlog forum, as well as the designs for a common mode / differential mode separator and this transient limiter.

Specifications & Operation

The leery-lisn is a 50uH LISN, which is the typical impedance value for conducted emissions testing between 150KHz - 30MHz, as specified in standards such as CISPR16. The leery-lisn is designed for a maximum input / output voltage of 240V, although the output plug is fixed as a US style 120V plug. The current rating is 5A RMS.

Due to the transient limiter, the common mode and differential mode outputs have 10dB of attenuation. For proper separation of the common mode and differential mode signals the unused output should be attenuated into 50 ohms.

The leery-lisn contains 8.1uF of capacitance between each AC leg and ground to decouple the LISN impedance from the impedance of the AC line. Due to the high ground currents resulting from this capacitance, consider using a isolation transformer between the AC line and the leery-lisn.

Performance

S21 measurements were taken of the leery-lisn to verify correct operation of the common mode / differential mode separator and impedance measurements were taken to check compliance with CISPR16 standard.

A very cursed adaptor was created to connect the AC output of the LISN to a VNA and measurements were taken with the AC input to the VNA shorted.

The leery-lisn is a three port device, so it can not be fully characterized with a two port VNA. However, a resistive splitter allows for accurately measuring the common mode S21 and the common mode rejection.

If it is assumed that driving one input to the LISN with the other terminated into 50 ohms provides a even split of common mode and differential mode stimulus, the differential mode S21 can also be measured.

The impedance of the two legs can also be compared against the CISPR16 standard, which provides a table of frequency vs the allowable |Z| and phase of the LISN input impedance. From the plot below it can be seen that the line leg of the LISN is slightly out of spec above 25MHz due to an extra 2" of wire running between the AC connector and the PCB. This is also the cause of the difference in the differential mode response for the two inputs of the LISN. leery-lisn technically does not meet the CISPR16 requirements, but should be close enough for pre-compliance work.

Construction

The leery-lisn is completely open source and the PCB design for the LISN and the front and back panels are provided in this repository.

Parts not on the BOM for the PCB are:

DescriptionQuantityPart Number
Enclosure11455T1601BU
Fuse Holder2696211001102
AC Outlet13-119-052
Power Switch1H8550VBBBEN551W
AC Inlet11-6609987-4

Improvements

A bleeder resistor should be added across the input capacitors to discharge them.

The impedance of the line side of the LISN is slightly outside of the limits specified in the CISPR16 standards due to the added wire length between the AC plug on the left side of the panel and the line input on the PCB, which is on the right. The front panel could be redone to reduce this wire length.

Parts

88
QtyValueFootprintReferences
1010uwbraun_smd:L_WURTH_WE-HCC-1090L2, L3, L4, L5, L6, L8, L9, L10, L11, L12
10DNPResistor_SMD:R_1206_3216MetricR21, R22, R23, R24, R25, R38, R39, R40, R41, R42
762409-1wbraun_smd:62409-1J3, J4, J5, J6, J7, J8, J9
62.7uCapacitor_THT:C_Rect_L31.5mm_W20.0mm_P27.50mm_MKS4C1, C2, C3, C4, C5, C6
6430Resistor_SMD:R_0805_2012MetricR13, R14, R20, R30, R31, R37
40.47uCapacitor_SMD:C_0805_2012MetricC7, C8, C10, C11
415Resistor_SMD:R_0805_2012MetricR16, R17, R33, R34
4MountingHole_Padwbraun_smd:M3-tight-fit-socket-headH1, H2, H3, H4
3DNPResistor_SMD:R_0805_2012MetricR5, R6, R8
20Resistor_SMD:R_0805_2012MetricR4, R7
20.1uCapacitor_THT:C_Rect_L26.5mm_W10.5mm_P22.50mm_MKS4C9, C12
210Resistor_SMD:R_0805_2012MetricR11, R28
212Resistor_SMD:R_0805_2012MetricR19, R36
2127Resistor_SMD:R_0805_2012MetricR18, R35
21mwbraun_smd:L_BOURNS_PM1812L1, L7
22045-09-BLFwbraun_smd:GDT_Bourns_2045GD1, GD2
2220Resistor_SMD:R_0805_2012MetricR15, R32
25Resistor_THT:R_Axial_Power_L20.0mm_W6.4mm_P25.40mmR1, R2
2560Resistor_SMD:R_0805_2012MetricR10, R27
2620Resistor_SMD:R_0805_2012MetricR9, R26
27.5Resistor_SMD:R_0805_2012MetricR12, R29
2BAV23SPackage_TO_SOT_SMD:SOT-23D2, D4
2Conn_CoaxialConnector_Coaxial:SMA_Amphenol_132203-12_HorizontalJ1, J2
2D_TVSDiode_SMD:D_SOD-323D1, D3
150Resistor_SMD:R_0805_2012MetricR3
1ADT2-71T+RF_Mini-Circuits:Mini-Circuits_CD637_H5.23mmTR1
1LOGOwbraun_smd:Beefield_logoG***

The 87 most common of 88 parts.

Similar boards

  • 4 layers40.6 × 20.8 mmSafepulse, the printed circuit board in 3D

    Safepulse

    Safecast/safepulse

    Open Source HVS for geiger counters.

    92 parts12
  • 2 layers187.5 × 45 mmGamma spectrometer, the printed circuit board in 3D

    Gamma spectrometer

    Motokichirou/gamma-spectrometer

    NaI(Tl) gamma spectrometer: STM32G474 + R1307 PMT + 4-board stack, KiCad schematics, LTspice simulations

    231 parts
  • 4 layers65.4 × 53.7 mmHV POWER SUPPLY, the printed circuit board in 3D

    HV POWER SUPPLY

    Sooraj21s/High-Volt-Radiation-Detect-PCB

    A PCB that converts the radiatoin detected by the geiger tube captured as milli volts to a high voltage by opamp & a buzzer is also provided in the module that triggers when the detected voltage reaches a certain…

    83 parts
  • 2 layers202 × 85 mmInstru bab v2 full, the printed circuit board in 3D

    Instru bab v2 full

    trublion/Boite_a_bourdon_control_board

    HW control board for motorised hurgy-gurdy. Controls a DC motor with a half-H-bridge, reads an analog audio signal envelope, dual-PCB design.

    147 partsMIT
  • 2 layers142.5 × 106.3 mmLily58, the printed circuit board in 3D

    Lily58

    kata0510/Lily58

    6×4+4keys column-staggered split keyboard.

    88 parts2.3k
  • 2 layers43.8 × 60.3 mmSmallreplacement, the printed circuit board in 3D

    Smallreplacement

    c0pperdragon/C64-Video-Enhancement

    Component video modification for the C64 8-bit computer

    88 parts286MIT
  • 2 layers95.3 × 95.3 mmRhymestone, the printed circuit board in 3D

    Rhymestone

    marksard/Keyboards

    This repository is warehouse of my keyboard architecture.

    88 parts193MIT
  • 2 layers69.9 × 108 mmAbakus Main, the printed circuit board in 3D

    Abakus Main

    mzuelch/CATs-Eurosynth

    Analog Synth Eurorack Modules

    88 parts166MIT

Questions

How big is the Lisn pcb PCB?

It measures 160 × 159 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Lisn pcb use?

88 parts, built around the 2045-09-BLF, BAV23S and ADT2-71T+. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Lisn pcb KiCad files?

From the westonb/leery-lisn repository on GitHub, at the commit this page was made from: the board is pcb/lisn-pcb/lisn-pcb.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Lisn pcb design in my own project?

Its repository states no licence, so its author keeps all rights: ask westonb before reusing the design.